Search Documents

By J. Koster

In the western United States occurs deposits of low-grade chromite which, when concentrated, may be reduced to ferrochromiun in electric furnaces that derive energy from dams and hydro plants now in course of construction. Montana ore was chosen for the experiments. A 1-ton sample contained 26 percent Cr203, 17 percent Fed, and 17 percent SiO2, plus other constituents, and the concentrates therefrom assayed 44 -percent Cr203, 23 percent FeO, and 0,79 per cent SiO2, Gravity concentration was found to be the best method. Ferrochromiums are of two grades - high-carbon with 66 to 70 percent chromium and 4-112 to 6 percent carbon and low-carbor with 67 to 72 percent chromium and 0.6 to 2 percent carbon. Both are made in electric furnaces that use anthracite as a reducer and suit-able fluxes. The concentrates mentioned mere smelted under different conditions, and it was concluded that domestic ore could be reduced with anthracite to produce a ferrochromium of S to 10 percent carbon content at yields of 90 percent without re-treating the slag. This carbon may be lowered to required proportion with calcium and silicon, but the former requires a great excess and the latter leaves an alloy high in silicon. INTRODUCTION Chromite occurs in several regions of the United States, but the known deposits of this mineral have not been large enough or high grade enough to permit them to compete under normal conditions with imported ores. There are numerous deposits of chrome ore along the West coast. These are generally conceded to be relatively small, although some were worked during the World War. There are some indications of a revival of interest in California chromites. Montana contains large chromite deposits in Stillwater and Sweetgrass Counties. The utilization of chromite for ferrochromium and. the manufacture of stainless steels is distinctly an electrometallurgical problem; consequently, a study of methods for treatment of chromite might pave the way for the establishment of new electrometallurgical industries in the Western States. This thought is supported by the cheap power that is soon to become available from the western dams, Farther, submarginal domestic chrome deposits might thus be turned into profitable producers.

Jan 1, 1936

By J. Koster

In the western United States occurs deposits of low-grade chromite which, when concentrated, may be reduced to ferrochromiun in electric furnaces that derive energy from dams and hydro plants now in course of construction. Montana ore was chosen for the experiments. A 1-ton sample contained 26 percent Cr203, 17 percent Fed, and 17 percent SiO2, plus other constituents, and the concentrates therefrom assayed 44 -percent Cr203, 23 percent FeO, and 0.79 per cent SiO2, Gravity concentration was found to be the best method. Ferrochromiums are of two grades - high-carbon with 66 to 70 percent chromium and 4-112 to 6 percent carbon and low-carbor with 67 to 72 percent chromium and 0.6 to 2 percent carbon. Both are made in electric furnaces that use anthracite as a reducer and suit-able fluxes. The concentrates mentioned mere smelted under different conditions, and it was concluded that domestic ore could be reduced with anthracite to produce a ferrochromium of S to 10 percent carbon content at yields of 90 percent without retreating the slag. This carbon may be lowered to required proportion with calcium and silicon, but the former requires a great excess and the latter leaves an alloy high in silicon. INTRODUCTION Chromite occurs in several regions of the United States, but the known deposits of this mineral have not been large enough or high grade enough to permit them to compete under normal conditions with imported ores. There are numerous deposits of chrome ore along the West coast. These are generally conceded to be relatively small, although some -were worked during the World War. There are some indications of a revival of interest in California chromites. Montana contains large chromite deposits in Stillwater and Sweetgrass Counties. The utilization of chromite for ferrochromium and. the manufacture of stainless steels is distinctly an electrometallurgical problem; consequently, a study of methods for treatment of chromite might pave the way for the establishment of new electrometallurgical industries in the Western States. This thought is supported by the cheap power that is soon to become available from the western dams. Farther, submarginal domestic chrome deposits might thus be turned into profitable producers.

Jan 1, 1936

By A. C. Richardson

The mine of the Porter Coal Co. is located at the town of Porter in the northwestern part of Jefferson, County, Ala., about 20 miles west of Birmingham. The operations in this mine are confined to the middle and bottom benches of the Mary Lee bed. The coal from the Porter mine is handpicked and washed before being placed on the market. The handpicked lump coal and the washed egg and nut, coal are sold chiefly as domestic and steam-raising fuel. The coal finer than 1 inch is washed in 2-compartment jigs and utilized in the manufacture of metallurgical coke. The coal company has found that, when coal ranging in size from 1 to 0 inch is washed in jigs, a considerable amount of high-ash material finer than 3/16 inch remains in the washed coal. This paper gives the results of an investigation which was conducted for the purpose of determining the washing characteristics of the through 316-inch raw coal and the extent to which the ash might be reduced by means of coal-washing tables. This investigation has been made in connection with an. extensive study of the coal-washing problems now being conducted by the United States Bureau of Mines and the University of Alabama, with the cooperation of the coal-mining companies of the State.

Jan 1, 1933

By J. J. de Barbadillo

This report describes a process for recovering chromium and other metals from superalloy scrap. Part I contains the results of laboratory scale experiments which were conducted to test a complex flowsheet utilizing a wide range of extractive metallurgical operations. The novel basis for the process is the formation of a sulfide matte in which chromium is concentrated in a discrete chromium sulfide phase. Mineral processing and hydrometallugical procedures are used to separate chromium sulfide from the other matte constituents. The products of the process are a chromium-nickel alloy suitable for reuse in the superalloy industry, electrolytic nickel, electrolytic cobalt, and an iron-molybdenum residue. Recovery of the principal elements contained in the scrap are chromium(Cr)-93 percent, nickel(Ni)-99 percent, cobalt(Co)-96 percent, molybdenum(Mo)-92 percent. Part II encompasses a preliminary engineering design of a pilot plant capable of treating 100 pounds(lb) of superalloy scrap per hour. Also included is an economic analysis of the operation of the pilot plant.

Jan 1, 1980

By William D. Monaghan, Michael A. Trevits

Over the period 2000 to 2003, roof falls have accounted for 4 to 14% of the fatalities in underground mining operations. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce the frequency, exposure, and risk of these events through an ongoing program of field and laboratory studies. One area of research involves the evaluation of polyurethane grouting technology that is commonly used to stabilize fractured mine roof strata. Concurrently, NIOSH is conducting work to evaluate the application of ground penetrating radar for advanced delineation of problematic mining areas. In this study, NIOSH partnered with Sub-Technical, Inc. who injected a polyurethane grout (also known as glue) into a roof area of NIOSH’s Safety Research Coal Mine. The mine roof area was scanned using ground penetrating radar technology before and after grout injection in an attempt to determine the extent of grout infiltration. A comparison of the pre-and post-grouting radar records showed a significant change at a mine roof depth of about four to five feet. The interpreted radar records were then compared with drill core information, borescope evaluation of roof-bolt holes in the study area, and underground observations. At this site, the interpretations of the radar records correlated with data obtained from the core holes, borescope evaluations and underground observations. This study showed that ground penetrating radar technology can be a useful tool for detecting changes in mine roof due to the injection of the grout.

By Louis H. Berkelhamer

"INTRODUCTION ""Free silica"" includes all free forms of silicon dioxide, such as quartz, chalcedony, tridymite, cristbbalite, opal, diatomaceous earth, and lechatelierite. The term, has been used rather loosely however, as synonymous with quartz, as quartz is the most abundant form of free silica. ""Combined silica,"" on the other hand, has been reserved to denote silica combined with other elements as silicates.Improvements in methods for the determination of free silica, and quartz in particular, have been the subject of considerable interest during the past decade, owing mainly to the accented and increased knowledge concerning quartz as a causative factor in silicosis. Analysis for quartz, however, is of importance in many other fields, including the determination of quartz in ceramic raw materials, such as feldspar and clay; the evaluation of a beneficiation procedure by the ore dresser, such as in the concentration of iron ore; control studies of a manufactured product, such as silica brick; and routine analysis of rock, mineral, and ore samples by chemists and petrographers."

Jul 1, 1944

By G. B. Gait

This report is the third in a series concerning the Bureau of Mines program for microfilming maps of abandoned mines in the Pennsylvania anthracite region; a catalog of the microfilmed maps of mines in the Lackawanna Basin of tile Northern anthracite field is presented. Previous reports IC 8274, published in 1965, and IC 8379, published in 1968, were catalogs of microfilmed maps of mines in the Eastern Middle anthracite field and Wyoming Basin, Northern anthracite field, respectively , Additional catalogs will be published as the microfilming of significant mining areas is completed.

Jan 1, 1970

By H. William Zeller, T. E. Westpha1

The U.S. Bureau of Mimes evaluated the effects of two iron-based fuel additives on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of engines used in underground mines. One additive, ferrous picrate, did not measurably affect exhaust emissions. This report is mainly about a ferrocene-based additive that reduced DPM between 4 and 45 pct, depending on engine operating conditions. The report concludes that the DPM reductions were caused by the catalytic oxidation properties of a ferric oxide coating that developed inside the engine's combustion chamber. The ferric oxide coating also decreased gas-phase hydrocarbons and O, but it increased CO, and NO,. The increase in NO,, of about 12 pct, is considered the only adverse effect of the ferrocene-based fuel additive. The results suggest that the effectiveness of ferrocene was partially offset by increased sulfates because of the high-sulfur fuel used. Recommendations for continuing fuel additive research are presented.

Jan 1, 1992

By John R. Zelonka

Models made by encasing strain-gage networks in epoxy are described and evaluated. With this technique relatively complex models can be constructed in which any number of gages can be located and alined precisely. Although the gages are an integral part of the model matrix, they create no important mechanical or thermal stresses. Model construction techniques and experimental data proved reproducible and reliable. In addition, the sGlution obtained with these models to the problem of the state of stress around a circular hole in a plate subject to a plane stress condition was in agreement with theoretical, photoelastic, and finite-element solutions.

Jan 1, 1970

By S. H. Ash

For many years the Federal Bureau of Mines has been investigating fires and explosions in mines, tunnels, buildings, and hazardous processes of various kinds. Means and methods for controlling and extinguishing mine fires and preventing explosions and other accidents in many hazardous processes require the collection and analysis of samples of the atmospheres surrounding the sources of ignition. Complex mixtures of gases often encountered in mines, tunnels, and industrial processes may well presage imminent danger from explosions. This report discusses some practicable methods of utilizing the analyses of samples of complex mixtures of gases in their application to the many problems that arise from their presence.

Jan 1, 1948

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain t did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A bibliography of pertinent literature is included as an appendix. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By Joan Weinberg

Real gross national produce (GNP) grew at a seasonally adjusted annual rate of 2.0% in the fourth quarter (table 1). The restrained quarterly growth rate was the slowest in 2 years, and was substantially slower than the 2.5 % rate of the previous quarter. According to the U.S. Department of Commerce, the summer drought reduced the fourth-quarter growth rate by 1.1 percentage points. A growing trade deficit and a reduction in business investment were the key economic factors curtailing growth. The trade deficit widened by $6.8 billion, reflecting both a surge of imports and a slowing of exports. Business investment declined 3.7%, mainly as a result of a slowdown in computer sales. On a year-to-year basis, the economy grew at an inflation-adjusted rate of 3.8% for 1988, the fastest in 4 years, despite the drought. However, on a fourth-quarter-to-fourth-quarter basis, real growth measured 2.7%. Increased exports and business spending for plant and equipment accounted for much of the 1988 GNP growth. Employment continued to grow as the manufacturing sector added 414,000 new workers (table 2). Of these, the primary metals industry added 26,000 workers, and the clay, glass, and stone industry added 10,000. The civilian unemployment rate remained low throughout 1988, fluctuating between 5.3% and 5.4% during the last quarter.

Jan 1, 1989

This Bureau of Mines report and its companion report (Information Circular 9143) have been prepared to assist in the preparation of prefeasibility type estimates for capital and operating costs of mining of various types of mineral occurrences using current technology. The handbook provides a convenient costing procedure based on the summation of the casts for the unit processes required in any particular mining or mineral processing operation. The costing handbook consists of a series of costing sections, each corresponding to a specific mining unit process. Contained within each section is the methodology to estimate either the capital or operating cost for that unit process. The unit process sections may be used to generate, in January 1984 dollars, costs through the use of either costing curves or formulae representing the prevailing technology. Coverage for surface mining includes dredging, quarrying, strip mining, and open pit mining. The underground mining includes individual development sections for drifting, raising, shaft sinking, stope development, various mining methods, underground mine haulage, general plant, and underground mine administrative cost. This system can be used for estimating cost data for an undeveloped deposit or for checking or verifying mining costs from a developed deposit, with a minimum amount of background information.

Jan 1, 1987

By G. R. Fitterer

In the manufacture of steel by any process the refining period involves the partial elimination of the metalloids carbon, manganese, phosphorus, and silicon, by virtue of their reactions with ferrous oxide. At the end of this refining stage the metal consists chiefly of iron in which small amounts of these materials are dissolved. Unless some deoxidizer is added to the steel at this time, the reaction between carbon and ferrous oxide will continue with such force that it is impossible to form sound steal in the ingot molds. Instead, the product will exhibit a marked porosity due to the formation and trapping of carbon monoxide-the product of the reaction mentioned. However, if deoxidizers are added, steel may be obtained which is dense and free from gas bubbles. At the same time the deoxidation products will remain in the steal as impurities. For example, silicon additions form Si02 or combinations of Si02 and FeO. Additions of manganese form deoxidation products consisting of various proportions of MnO and FeO. It is also quite obvious that simultaneous additions of manganese and silicon will form oxide combinations either in the binary system MnO-SiO2 or in the ternary system FeO-MnO-SiO2. Work at the Pittsburgh Experiment Station of the United States Bureau of Mines, in cooperation with the Carnegie Institute of Technology and the Metallurgical Advisory Board, involved the study of such deoxidizing reactions and their products. In this connection considerable information is necessary concerning FeO, MeO, Si02, and Al 203, and their various combinations. Some of the most needed data are the melting points of all of these materials. At the outset of this work ordinary methods of melting point determinations were found to be inadequate for various reasons, and the procedure finally selected involved the use of the micropyrometer with occasional corroboration by quenching methods, The reasons for this selection, together with a description of the apparatus, are given in the following pages.

Jan 1, 1932

By Howard E. Rollman

South Central United States, an area including Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas, is a net exporter of refractories. Nearly $45 million of these materials was shipped in 1954 from plants in the area, compared with area consumption of $18.5 million. About 88 percent of all refractories production is concentrated in Missouri. The prevalent consumption pattern, however, is one of localized shortages. For example, although Texas uses more than half of the refractories consumed in the South Central United States, production of refractories in Texas is relatively small. Also, the apparent self-sufficiency of the area is in terms of value produced rather than in terms of products consumed. Nearly all of the $6,425,000 nonclay refractories consumed in the area were shipped from other States. Local resources possibly could be developed for making refractories to serve markets that currently are being supplied from outside the area. Since other industries are growing rapidly in the area, the market for refractories is expected to continue to grow--more rapidly than the national market. The Missouri refractories industry is economically important nationally. Nearly one-fourth of the clay refractories produced in the United States are made in Missouri. Moreover, Missouri produces most of the higher grade clay refractories, about 62 percent of the high-alumina refractories, and 85 percent of the superduty refractories. The competitive position of the Missouri refractories industry is strong. The national market for clay refractories and the market in the South Central United States are expected to continue to grow. The ratio of net income to the value of refractories shipped in Missouri is larger than the national average.

Jan 1, 1960

By S. D. Hill

To help insure the continued viability of the minerals and materials sector of the U.S. economy, the Bureau of Mines is conducting research and disseminating technology that will result in more efficient minerals extraction. As part of this effort, a process is being investigated that involves an aqueous chlorine-oxygen leaching procedure to treat complex sulfide concentrates to produce ZnCl2. Subsequent fused-salt electrolysis of the ZnCI2 produces high-purity zinc metal. Previous reports described preliminary, small-scale research on the chlorine-oxygen leaching system and fused-salt electrolysis of ZnCl2. This report discusses the details of design, construction, and longterm, continuous operation of both monopolar and bipolar fused-salt cells. The effects of temperature, electrode gap, current density, electrolyte composition, and electrode configuration on current efficiency and energy consumption were determined for a ZnCl2-KC1-NaCl electrolyte system. Zinc metal was produced at the rate of about 50 lb/day in a monopolar cell which was operated continuously for 60 days with current efficiencies from 85.8 to 98.6 pct and an average power consumption of 2.1 kwhr/lb. Bipolar cells with several different electrode configurations were operated for 90 days. A current efficiency of about 70 pct and power consumption of about 1.7 kwhr/lb of zinc were achieved using a three-electrode-pair, bipolar assembly with a chlorine gas lift pump to circulate electrolyte.

Jan 1, 1981

By Jonathan Ludlow

This document is the final report of a study aimed at defining the relative contributions of various sources of respirable airborne dust on longwall faces. In order to define the contribution of various primary sources, continuous dust level data were recorded on five longwalls for an average of five shifts at each. By analysis of these data with records of face activity, it was possible to determine the overall contribution of each of the major elements of the longwall system to overall respirable dust exposure at various face locations. Average levels were determined for roof support generated dust, conveyor and intake dust and for dust levels during various shearer activities. When average levels are compared between mines, a significant degree of consistency is noted. The next phase of the study was aimed at differentiating the various dust sources associated with the shearer. To this end 'fly cuts' varying from 6 in. to 30 in. were closely monitored as were dust levels at operators' positions over the various segments of longwall cycle. These data indicated that the clearance ring of the shearer drum as a disproportionately heavy contributor to shearer dust make. A statistical analysis of the effect of shearer haulage speed on dust make revealed that high haulage speeds are associated with low specific dust make.

Jan 1, 1983

By W. G. Freeman

This study provides recommendations for improved safety in underground blasting procedures based on in-mine observations of blasting practices in 30 underground metal, non-metal, and coal mines, and the analysis of blasting accidents since 1970 and existing state and federal regulations pertaining to the storage and use of explosives. Results of these analyses and observations indicate that 1) blasting accidents have declined but are an important contributor to the hazards of underground mining; 2) existing regulations are essentially adequate; 3) greater emphases should be placed on human errors and unsafe practices and the enforcement of existing regulations; and 4) future revisions of these regulations and standards should be organized, and their intent coordinated to eliminate ambiguities.

Jan 1, 1980

By James Westfield

Drilling for roof bolting has created a new dust problem for the coal-mining industry. Drilling is inherently dusty, and control of dust produced by drilling vertical or nearly vertical holes is much more difficult than control of that produced by drilling flat or down holes.4/ Also, the dust produced by roof drilling differs in composition from that produced by drill-fur, or cutting the coal face because it contains a significantly greater amount of free silica and therefore presents a greater potential hazard of silicosis. Roof bolting has been practiced successfully in the mines of the St. Joseph Lead Co. in southeastern Missouri for over 20 years, but it was not until 1947 and 1948 that large-scale roof-bolting experiments were conducted in coal mines.5/ Although the need for dust control in conjunction with roof drilling was recognized from the beginning, the development and acceptance of roof bolting progressed so rapidly during 1949 and 1950 that solution of the dust problem lagged behind other engineering phases of the technique.

Jan 1, 1951

By H. C. Miller

Several agencies of the Federal Government are engaged in research and fact finding relative to petroleum and natural gas, and others are concerned with carrying out the provisions of specific laws that affect these natural resources in their broad aspects. The Bureau of Mines, however, is the only Federal agency designated by law to engage in research in oil and natures gas production, chemistry, refining, and

Jan 1, 1941