Search Documents

By J. E. Matta

The Bureau of Mines made laboratory absorption measurements on oil shale samples, which showed that the amount of methane absorbed is proportional to pressure and oil yield, and can be much larger than would be predicted based solely on porosity. Oil shale cores collected in the field were also measured for their gas content using the Bureau of Mines direct method. Cores taken from deep locations and far from outcrops yielded more gas than cores from shallower locations or at outcrops, when taking into account variations in oil yield, and all data indicate that oil shale mines that are both deep and far from an out-crop will emit low levels of methane gas.

Jan 1, 1977

By G. R. Strimbeck

The Federal Bureau of Mines has been developing processes for producing synthesis gas directly from coal, oxygen, and superheated steam. An atmospheric-pressure pilot plant was constructed and operated to: 1. Determine the operability of the plant for gasifying coals of different ranks under various operating conditions. Listed in decreasing order of rank, these coals included a Pennsylvania anthracite, a bituminous A coal from the Sewickley bed, West Virginia, and a subbituminous C coal mined in the Lake de Smet region of Wyoming. 2. Determine the effect of varying operating conditions on: (a) Standard cubic feet (std.c.f.) of oxygen and pounds of coal of different rank required to make M std.c.f. of product gas (carbon monoxide plus hydrogen); (b) carbon gasified, percent; (c) exit-gas temperature, degrees F.; and (d) heat loss, B.t.u. per pound coal. 3. Compare the gasification characteristics, indicated in item 2, of coals of different rank: Bituminous A, anthracite, and subbiturninous C. 4. Determine the concentration of dust in the gases produced and the efficiency of dust removal, and investigate the relation between the sulfur content in the coals gasified and the gases produced.

Jan 1, 1960

By Leroy Dockter

The grinding characteristics of lignite in a ball mill were investigated. The variables studied were initial lignite moisture content, degree of in-the-mill drying, and lignite source. The mill tested was a pilot-p1ant-size conical ball mill which had a maximum output of from 80 to 180 lb/hr pulverized product depending on the lignite and test conditions. The capacity of the test mill ranged from 82 to 103 lb/hr depending upon mine source, in pulverization of as-mined lignite with minimum drying, The capabilities of the ball mill could not be correlated to Hardgrove index of the individual lignites or other observed physical properties. Predrying lignite from its 35 to 40 percent raw moisture content to about 10 percent moisture before grinding improved the mill capacity 87 percent, compared to an increase in capacity of 74 percent with in-the-mi11 drying to the same product moisture.

Jan 1, 1967

By Kenneth G. Broadhead

Four applications of radiotracer techniques in metallurgical research are described: (1) In electrowinning tungsten from scheelite, molybdenum 99 was used to detemine the molybdenum concentration of the fused alkali-phosphate bath and the electrowon tungsten; (2) an attempt to detemine the solubility of tagged ceric oxide in molten CeF3-BaF2-LiF was unsuccessful, but a high rate of cerium ion exchange was observed; (3) iron 59 was added to cerium during casting and used to follow the migration of iron during solid state electrolysis; (4) radiotracers were used in developing special analytical techniques applicable to high-purity rare-earth metals produced by molten salt electrolysis.

Jan 1, 1963

By Martin H. Stanczyk

Acid leaching of selected copper sulfide minerals, impure copper sulfide flotation concentrates, and a cement copper precipitate at elevated temperatures and pressures was investigated. Copper extractions of 97 to 99 pct were obtained by leaching chalcopyrite and the flotation concentrates with water under oxidizing conditions at 200° C for 30 to 60 min. In tests with bornite, chalcocite,and cement copper, addition of sulfuric acid or pyrite to the autoclave was required to obtain similar copper extractions. The chemistry of leaching copper minerals was studied. It was determined that different copper sulfides altered to covellite as one step in their dissolution.

Jan 1, 1963

By R. V. Ramani, R. Bhaskar

"The results .of an experimental and theoretical research study into the spatial and .temporal behavior of dust in mine airways is summarized in the paper. Experiments were performed in mine airways under both controlled and .normal operating conditions. The controlled experiments included the documentation of the concentration and deposition patterns for two types of dust under three different velocities. Real-time dust concentration data were obtained using Real-time Aerosol Monitors (RAM-1) to determine the dispersion coefficient in a mine airway. On the theoretical front, a convection diffusion model of the dust flow phenomenon in mine airways was developed considering dominant mechanisms affecting dust transport and deposition in mine airways. Mechanisms modeled include turbulent and gravitational deposition, coagulation, and dispersion.In this paper, comparative analyses of results of the controlled experiments with the predictions of the mathematical model are presented. In addition to the overall validity, the adequacy of the individual components of the model, such as deposition in the total and respirable range, and dispersion are examined in light of the experimental observations.The experimental data from controlled experiments compared more favorably with model predicted results for similar conditions as opposed to the ·comparative analysis results for in-mine experiments. Specifically, the model· predictions for an 800-meter stretch of a mine airway reveal some significant differences from the behavior noticed in the mine. The deposition was lower than that predicted by the model. Consequently, concentrations were higher than those predicted by the model. The implications of these and other findings for further investigations are discussed in the paper."

Aug 31, 1989

By A. L. Engel

Simple treatment methods, employing the least possible equipment, can sometimes be established for marginal ores and economical results achieved. In continuation of a long-established part of the hydrometallurgical and ore-dressing program of the Reno Station of the Bureau of Mines, typical ores from newly discovered or recently explored mining districts have been investigated. The purpose of such investigations is to encourage the search for and development of mineral resources and particularly to assist in the economical exploitation of low-grade and marginal ores, as well as the conservation and recovery of values in products from former operations that were discarded because of past inability to treat them economically. Several of these investigations have been limited to preliminary tests of samples from prospecting operations, whereas some involved samples of old dumps or tailings piles. The test, work in these cases was not extensive enough to warrant publication as individual reports, but is of considerable interest inasmuch as it indicates the possibilities as well as the limitations of treating the respective materials; and because, inasmuch as the samples were representative of the districts from which they were obtained, this in-formation should be helpful in the future development of these districts. The present report is a compilation of results of brief preliminary tests on oxide ores only, which contained gold and silver and in some cases base metals. The methods of treatment used include gravity concentration, amalgamation, flotation, and cyanidation. For the most part, only standard laboratory procedures were employed. No attempts were made to develop new methods for the low-grade refractory ores in this group of samples if simple treatment was not successful, as the stage of development of the properties did not warrant extensive experimentation on the samples submitted.

Jan 1, 1951

By P. L. Woolf

Two blast furnaces, one a. commercial furnace and the other the Bureau of Mines experimental furnace, were successfully operated with extremely low slag volumes. The lowest slag rate obtained on the industrial furnace was 335 pounds per ton of metal. Using the same burden materials a 245-pound slag volume was achieved on the furnace. The coke rate saving and increase in productivity resulting from lowered slag rates are discussed as well as the factors limiting a low slag practice.

Jan 1, 1965

To provide longwall operators with a method to predict methane emissions from panels with increased face width.

Jan 1, 1997

By Jr. Watts, B. K. Cantrell, D. H. Carlson, K. L. Rubow, S. T. Bagley

"Permissible exposure limits (PELs) have been established for gaseous pollutants, carbon monoxide (CO), carbon dioxide (CO), nitric oxide (NO), nitrogen dioxide (NO2), and some gas-phase hydrocarbons emitted in diesel exhaust. There is, as yet, no PEL recommended for diesel exhaust aerosol (DEA), nor is there a standard method for sampling this aerosol.The University of Minnesota and the U.S. Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size-selective inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were made in underground coal mines that use diesel equipment.The mine mean DEA concentrations for the five mines surveyed, determined with the PDEAS in the haulageway, was 0.89 mg/m3, with a standard deviation of 0.44 mg/m3. DEA contributed 52 % of the respirable aerosol at this location.In three of the mines filter samples were collected for DEA-associated polynuclear aromatic hydrocarbons (PAHs) and biological activity determinations. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust. In general, the PAH and biological activity levels were similar for all three mines, and indicate that up to 25 % of the haulageway concentrations may be contributed by outby diesel vehicles. Measured concentrations of CO, CO2. NO, NO2, and SO2, were well below regulated levels.INTRODUCTIONDiesel exhaust contains pollutant gases, such as carbon monoxide, carbon dioxide, nitric oxide, nitrogen dioxide, and gas-phase hydrocarbons, as well as DEA. Much of the health-related concern focuses on DEA and associated organic compounds (Watts, 1992a). A wide variety of these PAHs have been identified and some are known carcinogens and/or mutagens. The U.S. Mine Safety and Health Administration (MSHA) has proposed new PELs for these and other contaminants (MSHA, 1989). MSHA has also published an advance notice of proposed rulemaking to establish a separate PEL for diesel particulate (MSHA, 1992)."

Nov 1, 1995

By Stephen P. Holt

In the fall of 1946 and spring of 1947 the Bureau of Mines put down five inclined diamond-drill holes totaling about 3,100 feet of bore to test for the possible eastward extension of the Royal Princess ore deposit in Jo Daviess County, Ill. Attention of the .Bureau was first directed to this property by the Illinois State Geological Survey. The history of production of the Royal. Princess mine and reports as to the size and nature of the deposit were considered justification for investigating the trend of the mineralization. This report describes the work done by the Bureau of Mines and presents the data obtained.

Jan 1, 1948

By Bruce D. Hanson

The Bureau of Mines conducted a series of ignition tests with two types of conical bits (plumb bob and pencil) used on continuous mining machines, to determine their ignition potential at various bit speeds, cut depths, and wear conditions. The tests were conducted using single bits mounted on a 34-in-diam drum in a Bureau ignition test facility. The bits impacted blocks of Berea sandstone in a 6.5 pet methane atmosphere at various bit speeds and cut depths. In a new condition, the plumb bob bits were considerably more incendive than the pencil bits, causing ignitions in 32 of 35 tests at 60 rpm, compared with ignitiolls in 2 of 22 tests for the pencil bits. The results from new bit testing also show that reduction of bit tip velocity to 180 fpm does not eliminate ignition potential. When subjected to progressive wear, bits of both types were more incendive when they were locked in place, unable to rotate, than when they were free to rotate.

Jan 1, 1983

By Joseph A. DeCarlo

For the first time the Bureau of Mines is combining, in one report, comprehensive tabulations on both beehive and slot-type ovens. This publication presents statistical data on the number and capacity of all such coke ovens in the United States on December 31, 1957. Combining data on both types of ovens should prove helpful to those interested in keeping abreast of the latest changes in carbonizing capacity, particularly since the coke has similar properties and uses. Annual reports furnished to the Bureau of Mines by coke-oven operators shared that 78 oven-coke plants were operating in 22 States on December 31, 1957. This was a decline of one plant from December 31, 1956, as the Republic Steel Corp. took the ovens at Canton, Ohio, out of production on December 17, 1957, for dismantling and rebuilding in 1958. Total oven-coke capacity was 80,299,400 tons in 1957.

Jan 1, 1958

By J. L. Eakin

The Bureau of Mines determined agents that are effective in foaming heavy brines and oil from gas wells in severe concentrations of sodium chloride, in severe concentrations of calcium chloride, or in moderate oil-brine mixtures. Dynamic foam tests were designed to select the more effective foaming agents. Numerous foaming agents were tested in concentrated simulated brines, in oilfield brines having varied concentrations of ions, in heavy natural brines, and in a commercial brine generally used as a reservoir pressure-balancing fluid. Several agents were detected that could perform efficiently in the field under the most severe saline conditions. Agents that promote foaming in oil-brine mixtures were also determined.

Jan 1, 1965

By L. M. Demers, D. C. Kuhn

It has been suggested that radicals on the surface of dust particles are key chemical factors in the pathophysiology that results from the occupational inhalation of coal and silica dust. In addition, oxygenated derivatives of arachidonic acid (eicosanoidsJ have been implicated as important biochemical mediator5 of mineral dust-induced lung disease through their role in bronchial and vascular smooth muscle reactivity, inflammation, and fibrosis. Therefore, we assessed eicosanoid production by the rat alveolar macrophage (AM) exposed in vitro to mineral dusts with varying surface chemical characteristics in order to determine if radicals associated with the mineral dust could influence the production of proinflammatory mediators in the lung environment. Primary cultures of rat AM were exposed to freshly fractured or "stale" bituminous coal dust, as well as untreated silica or silica calcined to 500 and 1100°C. Prostaglandin E1 (PGE;V, thromboxane Ai (T}(Ay, and leukotriene 84 (LTB; levels in incubation medium were determined by specific radioimmunoassay. When AM were exposed to freshly fractured coal dust, PGE2 production was markedly increased. In contrast, exposure of AM to "stale" dust significantly reduced PGE1 production. Exposure of AM to freshly fractured coal dust resulted in a significant increase in production by AM, while exposure to stale coal dust did not influence AM TXA1 production. Neither "fresh" nor "stale" coal dust had any effect on LTB4 production. In vitro exposure of AM to untreated silica resulted in a significant increase in TXA1 PGE.,, TXA; and LTB4 production compared with control. However, exposure of AM to silica calcined to 11oo•c resulted in eicosanoid levels that were not significantly different from control. These effects were still apparent 8 wk after calcination of the silica particles. Silica was a more potent activator of AM eicosanoid production than was coal, and amorphous fumed silica was a more potent activator of AM eicosanoid production than was crystalline silica. These findings suggest that radicals associated with respirable coal and silica particles may play a key role in the ability of mineral dust to activate AM eicosanoid production and therefore may be important in the pathophysiological consequences of occupational mineral dust inhalation.

Mar 1, 1992

By H. S. Caldwell

Molten zinc, condensed from zinc vapor, was used by the Federal Bureau of Mines to leach aluminum from an aluminum-silicon alloy made by carbothermic reduction of silicious aluminum ores. Zinc requirements were minimized by re-fluxing condensed zinc in a low-pressure, Soxhlet-type distillation unit. The minimum ratio of zinc used to aluminum in the crude alloy was approximately 2:1. When the system pressure was reduced from atmospheric pressure to 100 microns or less, the rate of aluminum extraction increased by a factor of 20. Leaching rates were much higher when the zinc vapor was condensed directly on the crude alloy than when molten zinc was passed over the alloy in the absence of appreciable zinc vapors. Observations indicated higher extraction efficiencies from crude alloys containing greater amounts of iron. Complete extraction was obtained with negligible loss of zinc. Assuming complete removal of zinc, the aluminum products will contain 1 to 6 percent silicon and about 0.5 percent iron plus titanium. The leached crude-alloy residue is a highly friable spongelike material containing about 80 percent silicon, several percent iron and titanium, with the remainder aluminum. This extraction method has been patented (Patent 2,810,637) and assigned to the Government. Research and development investigations are continuing at the College Park Metallurgy Research Center.

Jan 1, 1961

By B. J. Scheiner

Electrooxidation of cinnabar mercury ores (HgS) was investigated as a means of providing an effective and economical hydrometallurgical technique for extraction of mercury from its ores, particularly those too low in grade to allow economical metal recovery by retorting or furnacing techniques. Oxidation was accomplished by electrolysis of ere slurried with brine. Cinnabar was dissolved by oxidation of the insoluble sulfide to soluble mercuric salts. The mercury ion in a brine solution forms a stable tetrachloro complex. Typical laboratory experiments required I to 7 hours of electrolysis at 35-percent pulp density in a brine solution that contained 4 to 20 weight-percent sodium chloride (NaCl). Power consumption ranged from 10 to 50 kwhr/ton of dry ore. Mercury extraction values between 90 and 99 percent were obtained with all of the ores investigated. Subsequent mercury recovery from leach solutions was readily accomplished by precipitation on zinc. Pilot mill experiments in a 100- to 200-lb/hr extraction plant are in progress to quantify power and reagent requirements, and extraction and recovery data obtained to date closely parallel those obtained in the laboratory.

Jan 1, 1970

By P. R. Bremmer

As part of a program to devise alternative technologies for producing alumina from domestic resources, the Bureau of Mines investigated the leaching of calcined kaolinitic clay to form basic aluminum chloride solutions. Bench-scale experiments were conducted for single-stage batch leaching with AICl3 solution and three-stage countercurrent leaching with substoichiometric HCI. Variable conditions of clay calcination and leaching were studied to determine their effects on aluminum extraction and pregnant liquor composition,

Jan 1, 1984

By Lee M. Manna

Approximately 10,000, 10-Ton, 4 wheel, 2 truck, coal mine cars are in general service in U. S. Mines. None are equipped with an automatic braking system. Very few are equipped with hand or parking brakes. The report lists major manufacturers of the car and develops estimate as the percentage represented. It complies physical specification of cars of major car manufacturers, and develops a composite clearance diagram. It then discusses a pneumatic system employing truck components for an automatic system that could be used as an add-on unit. The components are listed and priced and a schematic circuit is developed for the system. Recommendations as to future programming are made.

Jan 1, 1976

By D. D. Fischer

Recovery and separation of molybdenum and rhenium from a process solution was accomplished by a technique developed by the Federal Bureau of Mines involving a combined solvent extraction and activated carbon adsorption procedure. The processing sequence required treatment of the solution with S02 to reduce the chlorate ion and adjust the pR prior to solvent extraction of molybdenum and rhenium with a tertiary amine. Molybdenum and rhenium were stripped from the organic phase with an NH40H solution, and the strip solution was then passed through activated carbon to preferentially adsorb the rhenium. After washing entrained molybdenum from the column with a brine solution, rhenium was eluted with an MeOH-H20 mixture. The activated carbon was regenerated with water. Molybdenum was recovered as (NH4)6Mo7024 by evaporating the column effluent. Rhenium in the column eluate was reextracted with a tertiary amine, stripped from the organic phase with dilute NH40H, and recovered as NH4Re04 by evaporating the strip solution. The final (NR4)Re04 product contained < 80 ppm impurities. Sodium sulfate was crystallized from the first solvent-extraction raffinate by lowering the solution temperature to 0° C. Precious metals contained in the original process solution were adsorbed onto the activated carbon.

Jan 1, 1975