Search Documents

By D. W. Frommer

As one phase of a general problem of recovering sulfide slimes, mineral-dressing research was conducted on flotation tailing from the St. Joseph Lead Co., Bonne Terre, Mo., mill to recover a significant portion of the residual, finely divided galena. Production of a high-grade concentrate was not part of the immediate objective. Only a reasonable ratio of concentration of lead sulfide slime was sought, since the problem of upgrading by mechanical or extractive processes would be considered in the later stages of this study. The results show that, from a feed material averaging 0.20 percent lead (about 70 percent finer than 400-mesh), a recovery of up to 45 percent could be effected by flotation in rougher concentrate analyzing up to 6.5 percent Pb. These results were obtained by using larger quantities of various xanthates and sodium sulfide than used customarily in mills. Sodium sulfide, which is ordinarily detrimental to flotation of galena, was beneficial in this case.

Jan 1, 1959

By M. M. Fine

A preliminary mineral-dressing study of five samples of East Texas limonitic brown iron ores was conducted as part of the Bureau of Mines program to develop and extend domestic resources of iron ore. The samples were considered to be typical of ore currently being mined and beneficiated by the Lone Star Steel Co. and Sheffield Steel Co. The objective of the research was to investigate those mineral-dressing unit operations that might recover some of the fine iron lost in current industrial wastes or perhaps improve the recoveries when applied to the ores as well. Since current industrial beneficiation practice yields a washed limonite analyzing 41 to 45 percent iron, higher grade concentrates were not sought in this laboratory study. Laboratory investigation included washing and sizing, reduction roasting, and subsequent magnetic separation of the finely ground roasted materials. The results showed that laboratory recoveries of over 80 percent of the iron were possible, for the ores investigated, at concentrate grades comparable to those expected from cur-rent industrial beneficiation practice. ACKNOWLEDGMENTS Acknowledgment is made to the Lone Star Steel Co. and Sheffield Steel Co. for supplying the brown iron-ore samples on which this research was conducted.

Jan 1, 1956

By R. A. Cortese

The U.S. Bureau of Mines has developed a flame-radiation-powered trigger device to explosively activate suppression barriers to quench gas and coal dust explosions. The major component of the device is a silicon solar panel, which converts radiation from the developing explosion into electrical energy to initiate an electric detonator, which releases an extinguishing agent into the advancing flame front. Solar panels that are rated to produce 20 W of electrical power when exposed to the sunlight are producing about 200 W when exposed to a full-scale dust explosion. The solar panel is electrically isolated from the detonator by a pressure-sensitive switch until the arrival of the precursor pressure pulse, which always precedes a deflagration. This combination of pressure arming and flame-powered photogenerator prevents false barrier activation and requires no external power supply.

Jan 1, 2010

By M. J. Ferrante

The standard enthalpy of formation, low-temperature heat capacities, and enthalpy increments above 298 K were determined by the Federal Bureau of Mines for synthetic dawsonite [NaA1C03(OH)21. The enthalpy of formation was determined by hydrochloric acid solution calorimetry, with the result ?Hf°298 = -469.4±0.7 kcal/mole. The low-temperature heat capacities were determined from 6 to 307 K by adiabatic calorimetry. Tabulated are low-temperature values of Cp°, S°, and H.-Ho° from 3 to 298 K. The derived entropy at 298 K is S298 = 31.55±0.3 cal/deg mole. Enthalpy increments above 298 K were obtained by copper-block drop calorimetry. Tabular data of Cp°, S°, H°-H°298, -(G°-H°298)/T, ?Hf°, ?Gf°, and log Kf are given from 298 to 477 K. Enthalpies and Gibbs energies of decomposition are also reported.

Jan 1, 1976

By Philip C. Tully

This Bureau of Mines report contains experimentally determined vapor-liquid equilibria data for a helium-nitrogen-methane mixture with a nominal composition of 15, 60, and 25 mole-percent, respectively. Measurements of the equilibrium phase compositions were obtained by means of a windowed cell, in conjunction with an automated chromatograph and a special analyzer for low helium concentrations. The data presented include a comprehensive table and eight graphs depicting phase compositions, vaporization ratios, and correlations with a previous study of two helium-nitrogen-methane mixtures of different compositions.

Jan 1, 1976

By A. F. Colombo, D. W. Frommer

Bench- scale tests were made to determine the applicability of flotation as a means of upgrading finished and semifinished magnetic concentrates prepared from reductively roasted iron ores . Both anionic and cationic flotation methods were used to remove siliceous gangue from the magnetic concentrates and produce upgraded products . Seven magnetic concentrates , containing from 6.7 to 13.7 percent SiO2 , were improved by the flotation treatment , yielding final concentrates containing less than 6.0 percent Si02 . Cationic flotation methods were studied on four of the seven samples ; of this group only one sample yielded better results by cationic flotation than by the anionic method .

Jan 1, 1964

By J. B. Cheung

The results of a program to demonstrate the technical feasibility of hydraulic borehole coal mining are presented in this report. The hydraulic borehole method of coal mining involves inserting a hydraulic mining device into a borehole that has been drilled from the surface into the underground coal bed. The borehole mining device issues a jet of water under high pressure, which breaks the coal. These pieces of coal, along with the water, form a slurry, which flows to the base of the borehole where it is pumped to the -surface. Phase I of the program encompassed the design, fabrication and factory-testing of a hydraulic borehole mining device. The program was successfully completed with the field tests being conducted at the Wilkeson-Carbonado Coal Field near Wilkeson, Washington. The technical feasibility of hydraulic borehole coal mining was demonstrated by mining 32 tons of coal at a depth of about 75 ft over a period of 4 hours.

Jan 1, 1976

By F. W. Lee

The paramount importance of water to life of all forms on the earth is too well known to require elaboration in this brief paper. It has repeatedly been termed the most valuable of all our mineral resources. Its importance is justifiably recognized in the extensive areas covering the earth which receive sufficient rainfall to sustain a relatively luxuriant vegetation; but in those areas where rainfall is insufficient to support anything but a relatively meager plant growth, the location of a water supply and its development become of even more vital interest to those attempting to obtain a living from the soil. Geological investigations concerning the water supply of the United States have been most extensive, important work having been accomplished by Federal, State, and local governments and by private enterprise. A casual examination of the titles of the 739 Water-Supply Papers published by the United States Geological Survey3/ alone testifies 'to the vital nature of our water resources and the extensive work that has been done on them.

Jan 1, 1936

By Efrem R. Reeves

Noise-induced hearing loss (NIHL) is the most common occupational illness in the United States, with 30 million workers exposed to excessive noise levels [NIOSH 1996] every day. Of particular concern is the mining industry; which has the highest prevalence of hazardous noise exposure of any major industry sector [Tak et al. 2009] and is second only to the railroad industry in prevalence of work-ers reporting hearing difficulty [Tak and Calvert 2008]. This document is for operators, safety personnel, and mechanics in the mining industry who are not specialists in noise control engineering or acoustics. Evaluations of successful and unsuccessful attempts at controlling noise on several large, underground metal mining machines are detailed to illustrate the basic principles of noise control. Once personnel understand the guidelines and principles of noise control, they will be able to ¦evaluate the extent of a noise problem; ¦determine the best approach to the problem; and ¦apply the most appropriate solution. Because of the insidious nature of NIHL, it can go unnoticed until a considerable loss of hearing has occurred. In some cases, diagnosis is delayed because an exposed individual claims to have become accustomed to the noise. In reality, that person may have already suffered irreversible hearing loss. Humans can hear sounds in the frequency range from about 20 to 20,000 Hertz (Hz). Within this range, NIHL usually begins in the frequency region around 4,000?6,000 Hz, the upper levels of the speech region. The first noticeable symp-toms include difficulty understanding higher pitched voices, such as the voices of females and children, and difficulty understanding certain consonant sounds, which are primarily high frequency in nature. The extent of NIHL varies depending on the level and duration of noise exposure and on an individual?s susceptibility; despite having similar noise exposure, individuals can experience differing degrees of hearing loss, or none at all. NIHL is almost always preventable. To reduce or eliminate the possibility of NIHL, an individual?s noise environment must be analyzed and appropriate action taken to reduce noise exposure.

Dec 1, 2009

By Elton L. Litchfield

The Bureau of Mines determined minimum energies for direct initiation of expanding gaseous detonation waves in acetylene-oxygen mixtures. Composition limit ranges for the initiation of detonation with fixed energies have been compared to data in the literature. Assuming that the stored electrical energy is completely converted to thermal energy, the agreement between the energy of primary explosive initiators and the energy of electrical discharge initiators was good. Minimum energies for initiation of detonation in the most sensitive composition (40 percent C20 plus 60 percent 0 2) were: 0.64 joule at an initial pressure of 1/4 atmosphere, 5.0X10-2 joule at 1/2 atmos¬phere, and 3.7X10-3 joule at I atmosphere. Fuel concentrations in mixtures initiated to detonation by 4.9X102 joules ranged from 10 to 65 percent C2H2 at 1/4 atmosphere, 10 to 67 percent C2H2 at 1/2 atmosphere, and 9 to 68 percent C2H2 at 1 atmosphere.

Jan 1, 1967

By A. Z. Dimitroff

An improvised rock-dust disseminator, consisting of a 10-gallon galvanized metal milk can that dispenses rock dust in return air currents by the injection of compressed air has reduced the float dust explosion hazards at the Koehler coal mine, Koehler, N. Mex.

Jan 1, 1965

By W. T. Millar

Magnetite mines in the Sterling tract, Orange County, N. Y., were operated almost continuously from pre-Revolutionary days until 1923. The Red-Back mine, one of several in this tract, was discovered in 1780; operated briefly in 1880; and abandoned, presumably because the iron ore contained considerable sulfur. The mine is in rough, mountainous country, with altitudes ranging from 500 to 1,100 feet. The magnetite deposit occurs in complex metamorphosed pre-Cambrian formation and is thought to be a replacement of limestone by magnetite. A dip-needle survey, completed in 1916, traced magnetic anomalies for a mile along the outcrop. A preliminary examination of the Red-Back mine was made by W. T. Millar, Bureau of Mines engineer, in December 1942. The Bureau of Mines bored seven diamond-drill holes aggregating 2,727.6 feet during the winter of 1943-44. A zone of magnetite mineralization was intersected in each of the holes.

Jan 1, 1949

By J. M. Stuve

Low-temperature adiabatic heat-capacity determinations were made by the Bureau of Mines in the temperature range from 5 to 300 K for the two crystalline modifications of zinc sulfide, sphalerite (ß) and wurtzite (a). The entropy at 298.15 K of sphalerite was evaluated as l4.02±0.04 cal/deg mole and wurtzite, l4.06±0.04 cal/deg mole.

Jan 1, 1974

By J. K. Whyatt, B. G. White

Various methods of monitoring slip movements on bedding planes, as well as examination of rock burst damage in stopes, suggests that rock bursts in the Lucky Friday Mine are closely associated with these movements. Slip displacements along bedding simultaneously reduce the physical dimensions of stopes and increase compressive stress along stope margins. Such changes, in turn, contribute directly to rock bursts and the sudden failure of volumes of rock and cemented sandfill surrounding stopes. The distribution of seismicity and several mining-induced and premining structures resemble those described in South African gold mines. These suggest fundamental similarities in seismic sources and mechanisms of rock burst damage.

By Marvin L. Whisman

A radiotracer technique developed by the Bureau of Mines extends to the parts-per-billion range the sensitivity for determining contributors of deposits formed in stored and thermally stressed jet fuels. The method depends upon measuring radioactivity associated with thermally induced deposits from fuels containing one labeled compound. The technique was applied to 88 test blends, representing 12 fuels and nine carbon-l4 labeled fuel constituents or fuel additives, or both. Data from results of these tests are included in this report. With this radiotracer technique, the contribution of fuel components and additives to thermally induced deposits in a variety of fuel environments was estimated before and after storage.

Jan 1, 1969

By James P. Rider

This U.S. Bureau of Mines report describes a viewing transformation algorithm that generates a perspective view of a three-dimensional scene. This tool may be used by researchers to improve mine safety by assessing the visual capabilities of a mobile equipment operator. Three-dimensional transformations used to build the viewing transformation and techniques used to project the image onto a two-dimensional display screen are defined. The algorithm is written in the C-programming language and designed to stress portability, allowing it to work without significant modifications on numerous computers. A listing of the computer routines along with sample output is included in the report.

Jan 1, 1992

By Andrew J. Fergus

The purpose of this study was to provide basic information to aid further research on beryllium mineral flotation. Contact-angle and microflotation (Hallimond tube) methods were used to study collector action and flotation response of beryllium minerals and associated gangue minerals with representative commercial surfactants. Chrysoberyl received prime attention. Results indicated that selective flotation of beryl and chrysoberyl from fluorite and quartz is possible with sodium isooctyl phosphate below pH 2, and fluorite and topaz are readily collected by both anionic and cationic surfactants. Several modifying reagents were studied at one pH and one level of collector concentration. Aluminum sulfate, starch, and sodium silicate proved to be depressants in chrysoberyl flotation.

Jan 1, 1968

By M. H. Stanczyk

The Bureau of Mines made bench-scale laboratory tests on a sample of typical Florida phosphate slime to determine alumina and phosphate extractions obtainable by agitation leaching, by baking and curing, and by a leach-electrolysis scheme. Recovery of mineral values from leached slime pulps by resin-in-pulp ion exchange contact and the reaction of the leached pulps to filtration, flocculation, and settling were also investigated. The best extractions of alumina and phosphate were obtained by (l) agitation leaching with sulfuric, hydrochloric, or nitric acid at an elevated temperature or (2) curing or baking the slime with sulfuric acid. Alumina extractions ranged from 80.8 to 90.0 percent and phosphate extractions ranged from 93.3 to 98.4 percent when the slime was leached at 90° C with sulfuric, hydrochloric, or nitric acids. Baking the slime with sulfuric acid at 200° C for 4 hours yielded an alumina extraction of 92.3 percent and a phosphate extraction of 97.0 percent, whereas curing with sulfuric acid at 100° C for 24 hours gave slightly higher alumina and phosphate extractions. Flocculation and settling properties of the slime were virtually unaffected in all cases. Filter area requirements, although somewhat improved as compared to untreated slime, remained relatively high. The lowest filter area requirement obtained was 44 square feet per ton of dry solids treated per day. Contacting leached slime pulps with ion exchange resins depleted the leach pulps of solubilized values; however, the filtration and settling properties of the barren pulps were unaffected. A leach-electrolysis scheme resulted in some concentration of solubilized phosphorus, but the method showed little promise of being commercially feasible.

Jan 1, 1966

By Fred D. DeVaney

Copper sulphate is a common flotation reagent for blonde ores. Metallic iron also is present in the mill circuit, and a reaction between the iron and the salt would be in accord with well-known chemistry. The abundance of metallic iron in a flotation food may be noted by even perfunctory examination. First of all the mine contributes metallic iron, then the coarse-crushing machines add their share, and finally the fine-grinding medium its portion. If the grinding is with cast-iron balls the amount of metallics is greater than when steel is used. Thus it, is that much more metallic iron is present than would be indicated by noting the ball consumption. An estimate that the total amount of metallics is twice that supplied by the balls and liners might not be far amiss. That copper sulphate plates out on iron in an acid solution is well known, but since flotation is practiced commonly in solutions where acid has not been added this reaction has not been given sufficient thought.

Jan 1, 1929

By W. H. Ode, W. A. Selvig

"INTR0DUCTIONAccording to the Standard Specifications for Classification of Coals by Rank of the American Society for Testing Materials (A.S.T.M. Designation: D388-38).1/ high-volatile bituminous coals, subbituminous coals, and lignites are classified on the basis of calorific values on the ""moist"", mineral-matter-free basis. The moist basis refers to coal containing its natural bed moisture but not including visible water on the surface of the coal. It is assumed that the natural bed moisture of coal in the ground represents the moisture-holding capacity of the coal when in equilibrium with air at approximately 100 percent relative humidity. This moisture is sometimes referred to as inherent moisture as opposed to extraneous moisture, which wets the surface of the coal.To simplify procedures for determining the moisture-holding capacity of coal it is assumed, for all practical purposes that the moisture content of coal when brought to a standard condition of moisture equilibrium in an atmosphere of 97 percent relative humidity and 300 C. represents the bed moisture of the coal. The A.3.T.M. specifications provide that this condition of moisture equilibrium shall be obtained by bringing the coal to a standard condition of moisture equilibrium at 300 C. in a vacuum desiccator containing a saturated solution of potassium sulfate (97 percent relative humidity) according to the procedure proposed by Stanfield and Gilbart. 4/ No mention is made in the specifications for bringing partly air-dried samples to their natural bed moisture condition probably because of the hysteresis effect that has been noted by various investigators. 5/ In this connection it has been found from sorption studies that the adsorption and desorption curves for lignite are not entirely reversible. The hysteresis effect has been explained by some investigators as resulting from shrinkage of the lignite during drying, which causes a collapse of some of the capillaries, so the dried lignite cannot take up as much water as it held originally."

Apr 1, 1953