Search Documents

By Constantine C. Popoff

"INTRODUCTION AND SUMMARYDuring 1946 several high-grade limestone deposits in western Washington were examined by the Bureau of Mines. This report presents the data obtained from investigation of the Sauk Mountain deposits in east-central Skagit County, Washington.The investigation consisted of transit and topcgraphic surveys and sampling. The areas selected for sampling were first cleaned by blasting; channel samples up to 40 pounds were cut where practical. Chip samples averaging 30 pounds were taken where channel samples could not be cut. A total of 21 samples in the Sauk Mountain area were taken and. analysed. The locations of the samples are shown in figures 2 and 4, and the analyses are listed in tables 1 and 2. This investigation is a part of a long-range program of general investigation of mineral resources for future industrial development of the Pacific Northwest. The Sauk Mountain deposits were investigated for the purpose of disclosing now sources of high-purity limestone, which could be mined and shipped at low cost to Seattle and other industrial cities in the Pacific Northwest."

Oct 1, 1948

By R. Blickensderfer

Several thin film absorber stacks with spectrally selective characteristics were developed by the Bureau of Mines. The stacks consisted of a silicon thick film or a zirconium compound thin film on a reflective thin film of silver. The zirconium absorber films, with the general formula ZrCxOyNz, were prepared by reactively sputtering zirconium or zirconium carbide in argon with small amounts of oxygen, nitrogen, or both, or by oxidizing zirconium films in air. A few similar types of films were prepared from titanium. The short-wave absorptance over the solar spectrum, a(s), and thermal emittance at 600 K, e(600 K), of the solar absorber stacks were calculated from room-temperature reflectance data. The values of a(s) ranged from 0.47 to 0.93, e(600 K) from 0.49 to 0.034, and the ratio a(s)/e(600 K) from 1.7 to 34. The specimen with the best combination of properties, a ZrNx-Ag stack, had a solar absorptance a(s) of 0.85 and a ratio, a(s)/e(600 K), of 24. The effect of film thickness and composition on spectral selectivity was determined. An emissometer for measuring normal total emittance up to 800 K and a method for determining a (s), e(T) (hemispherical), and a(s)/e(T) using simulated solar radiation are described. A calorimetric method for measuring a(s) and e(T) (hemispherical) at elevated temperature is also described. Measurements made on several specimens agreed favorably with calculated values.

Jan 1, 1976

By Hugh Haddow

This paper describing the methods of recovery and treatment of a sand and gravel deposit and the preparation of these materials for a number of special markets is one of a series being prepared by the U. S. Bureau of Mines. It is of particular interest to those sand and gravel operators who have a surplus of fine sand which must be sent to waste, both from the point of view of, equipment and the variety. of markets supplied, and in that it describes one of the few sand and gravel plants which have resorted to hydraulic classification for sizing fine sand. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of J. R. Thoenen, mining engineer of the Bureau of Mines, in the preparation of this paper.

Jan 1, 1931

By R. V. Lundquist

A method was developed by the Federal Bureau of Mines for evaluating viscosity data from slurries obtained in leaching sinters from the lime soda sinter process for extracting alumina from aluminous silicates. The logarithm of the viscosity was observed to be a linear function with time. The slope of the plotted line provides a means for evaluating viscosity behavior in a lime soda sinter blurry and also a means for comparing gelation characteristics directly with other variables in the lime soda sinter process. This report presents one aspect of a continuing study by the Bureau of Mines on methods for treating siliceous aluminum ores. It is one of the many programs of the Bureau concerned with conservation, development, and use of our domestic minerals resources. Previous investigations of lime soda processes, both by the Bureau4-7/ and industrial concerns, have demonstrated that sintered materials containing CaO, Na2O, A1203, and S102 in various combinations exhibit a tendency to gel or set when mixed with water or other extraction solutions. Gelling prevents satisfactory recovery of alumina and in extreme cases prevents operation of an extraction plant.

Jan 1, 1960

By Frederick C. Trutt

Research performed on arcing faults and their interaction; with electrical insulating materials within coal.-mine power-system enclosures is described. This work was performed at The Pennsylvania State University from 1 December, 1976 through 30. November, 1977. Results presented are interim in nature and future research is planned to integrate the simulations which have been constructed, as well as to apply developed experimental procedures to the evaluation of electrical insulating materials for use in coal-mine enclosures. The thrust of this research has been divided into several primary areas. These include the development of a theoretical procedure for computation of three-phase and line-to-line arcing fault currents as a function of time, formulation of an arc model based upon thermal-arc plasma properties so that arc voltages and energies may be computed, development of a simulation for pressure and temperature rises when an arc interacts with an electrical insulating material within an enclosure, experimental evaluation of electrical insulating materials in terms of their tendency to support an arc as well as their potential contribution to enclosure pressure rises, and integration of the above research areas to form overall procedures for theoretical and experimental evaluation.

Jan 1, 1977

By Robert J. Anderso

Few elements have received more attention and developed greater interest in the last ten years than titanium. The substantially pure metal has been din...ie. cult to isolate, and so far has been little employed oommercially, but the use af alloys and chemical compounds of titanium has increased markedly in recent years. The earlier attempts at preparing pure titanium resulted in various impure forme which, from their metallic appearance, were always mistaken for the metal. Hunter in 1910 isolated pure titanium by the reduction of titanium tetrachloride with sodium. This brief statement is issued by the Bureau of Mines in response to numerous inquiries which have been received concerning titanium. More complete in. formation on the metal may be had by consulting the referenpes appended. The Literature is voluminous and only the more important references are Riven. It has been drawn upon freely in preparing this report; also information was supplied by M. g. Hunter, Arthur Braid, M 1. Schmid, C. M. Johnson, N. B. Hoffman, and de Courny Browne. The pioneer investigator in titanium is A. IL Rossi.

Oct 1, 1922

By F. E. Brantley, D. M. Yergensen, D. A. Martin

Fluidized - bed roasting was investigated as a means of decomposing gypsum and gypsum mixtures to produce a gas rich in sulfur dioxide and a lime or portland cement residue . Ninety- eight percent desulfurization of gypsum in a 10 - inch fluidized- bed reactor took 1.5 hours at an operating temperature between 1,200 ° and 1,225 ° C. A cement- type residue was obtained but had to be refired at 1,450 ° C before mortar prepared from it met the physical specifications for cement .

Jan 1, 1963

By C. J. Chindgren, L. C. Bauerle, J. B. Rosenbaum

Modifications of the conventional method of preparing ductile vanadium metal by calcium reduction of V2 05 in a bomb were explored for clues to a more economical procedure . The modifications examined included ( 1 ) omitting the gas purge of the bomb ordinarily used for eliminating atmospheric nitrogen , (2 ) using low- grade vanadium feed materials , ( 3 ) using alternative reductants , such as aluminum , magnesium , and silicon , and reductant mixtures , and ( 4 ) bomb refining of aluminothermic metal produced in open- vessel reductions . The most promising modification appeared to be bomb refining , using calcium to purify vanadium metal -- of low aluminum but high oxygen content-- prepared by open- vessel aluminothermic reduction of vanadium pentoxide .

Jul 1, 1960

By Van H. Manning

Chemical and physical tests of coals for the use of the Government have been made by the United States Bureau of Mines. These tests form part of a general study of the coals in the United States with respect to the manner in which each coal can be utilized most efficiently. As a result of this study, much information of value to all industries using coal has been compiled. Special investigations by the Bureau of Mines of the fuels used by the Government have, until recently, been for the most part limited to coal. In the course of these investigations the bureau has de- veloped new methods for use in the purchase of coal by the Gov- ernment. The application of these methods permits an intelligent selection of the coal adapted to the requirements of particular heat- ing or power plants, and has already resulted in the saving of large sums of money. In addition, these investigations have led to the compiling of a series of carefully made analyses of samples of coal collected in a predetermined manner in the mines of all the impor- tant coal fields in the United States, and these analyses are being published to enable Government purchasing agents and all users of coal to select the coal best suited to their needs. The purpose of this paper is to describe briefly the general char- acter and commercial quality of some of the coals mined in the United States that reach tidewater shipping ports, and to show in a general way the important characteristics of those coals that by reason of transportation facilities and the situation of the coal fields are most available for export. Coals of excellent physical character and of high heating value are available for export. For this reason and because of the modern facilities at the collieries for properly grading large shipments, American producers can supply coals suitable for any kind of service. The transportation system from the mines to tidewater and the coal- handling equipment for loading boats at the various ports are highly developed, so that producers are able to give excellent service to foreign buyers. Enormous quantities of these coals have been used by railroads, manufacturing, illuminating-gas, and coke plants, and seagoing vessels, and for household purposes. Much of the coal available for export is superior to the coals that have been supplied to foreign users from other sources.

Jan 1, 1916

To provide a means for mechanically separating and recovering nonferrous metals continuously from non-magnetic reject material produced at scrap automobile shredding facilities. Approach The Bureau of Mines developed a water elutriator system that separates metals from shredded scrap auto-mobiles based on differences in specific gravities. A premium-quality product, containing aluminum, magnesium, lead, zinc die cast, copper, copper alloys, and stainless steels, is obtained. How It Works Mixed nonmagnetic reject material currently being separated at automobile shred-ding facilities is introduced onto the top of an upwardly flowing vertical column of water. The water, overflowing a weir in the top of the vertical column, carries with it the floating, lightweight waste materials, mostly combustibles, while the heavier pieces sink through the rising water. Medium-density substances such as glass, rubber, and heavy plastics are carried off through a side port, located in the upper third of the column. The cleaned, mixed metal product sinks to the bottom and is continuously removed from the base of the column with a bucket elevator having perforated buckets. All three categories of material are removed from the system on separate wire mesh belt conveyors. Most of the water drains through the belts into a holding tank and, after settling, is recirculated back through the elutriator column. The purity and recovery of the metal product are influenced by two elutriator operating variables: the flow rate of water through the vertical column, and the height of the overflow weir at the top of the column.

Jan 1, 1983

The coal reserve base is defined for coalbeds having sufficient thickness for underground mining within a depth range compatible with economic recovery. The reserve data are compiled by the Federal Bureau of Mines by updating and reevaluating previous estimates of the U.S. Geological Survey, State geological surveys, and others. Through the application of computer techniques, the tonnages are compiled by State, county, coalbed, and rank. Coal reserve base is allotted to sulfur categories by a statistical apportionment of data from available Bureau of Mines reports and records. The coal reserve base in those States east of the Mississippi River, minable by underground methods, is estimated to be 169 billion tons in coalbeds greater than 28 inches in thickness to a maximum depth of 1,000 feet. Excluding those coals in reliability categories other than measured and indicated, the underground reserve base includes 162 billion tons of bituminous coal and 7 billion tons of anthracite. Of the total, 27 billion tons contains 1.0 percent or less sulfur. Most of this low-sulfur coal is in the southern Appalachian area. Approximately 16 percent of the underground reserve base is without available analyses. Included in this report is a glossary of terms applicable to a classification system for coal resources and reserves. The purpose of this system is to provide a common yardstick for determining coal resources and reserves.

Jan 1, 1974

By H. W. St. Clair

This study of the rate of evaporation of zinc was undertaken as a part, of a general investigation on refining mixtures of metals resulting from melting reclaimed scrap. One of the methods by which the more volatile metals, such as zinc, magnesium, and cadmium, may be separated is by distillation. Distillation may be carried out at lower temperatures if it is done in an evacuated enclosure. The immediate purpose of the present investigation was to determine accurately the effect of temperature, pressure, and other factors on the rate of evaporation of zinc.

Jan 1, 1950

By I. D. Shah

The Bureau of Mines investigated the sequence of principal chemical reactions taking place during the roasting of covellite (CuS). Practically all covellite is converted to digenite (Cul.SS) before oxidation to Cu20 begins. Part of the Cu2O is then converted to CuO, which in turn forms CuS04 through CuO?CuS04 as an intermediary. CuS04 and CuO'CuS04 decompose at 600° to 700° C to yield CuO and S03 (g) as final products. An overall mechanism is proposed for chemical reactions occurring at different interfaces of partially oxidized CuS pellets.

Jan 1, 1970

By James H. Cobbs

The purpose of this study is to investigate the application of boring equipment to the production of anthracite coal from steeply pitching beds. Both raise boring and augering equipment were considered. Previous studies (11) have indicated that boring equipment may have definite applications to the development of steeply pitching anthracite beds. This investigation was to carry forward previous work to determine the possible application of the two different types of equipment being considered. Previous conclusions have been substantiated by the results of this study.

Jan 1, 1975

By D. G. Kesterkel

Low-melting thoriurnrbase binary alloys or metal solutions were prepared by two different techniques involving the electrolysis of ThO2 dissolved in fluoride melts. Experiments were performed at 950° to 1,250° C using electrolytes containing ThF4 and various alkali and alkaline earth fluorides. In the first method, electroreduction of ThO2 and deposition of thorium on a nickel or iron cathode formed a molten alloy that dripped off and collected on the bottom of the cell, or in a tungsten cup. An electrocodeposition technique was used to prepare thorium-base alloys or solutions containing nickel, iron, chromium, or manganese. Electrolytic reduction of the component metal oxides and simultaneous deposition of the two metals on a tungsten cathode yielded a liquid alloy product. Complementary experiments were performed on the fused fluoride electrowinning of dendritic thorium from Th02 at 1,075° to 1,200° C in which thorium crystals were recovered and arc-melted into buttons. Major contaminants were aluminum, carbon, copper, iron, oxygen, and silicon, totaling 0.2 percent.

Jan 1, 1966

By R. D. Currie

Haulage accidents in the anthracite region cause fewer fatal and lost-time accidents per million man-hours than similar accidents in bituminous mines, a fact that may be accounted for in several ways, but primarily because haulage, in a large part of the region, is restricted to haulage crews operating only on the gangways where most of the miners seldom come in contact with movement or handling of cars and locomotives. Generally in underground mines the number of men injured compared with the number killed is greater for haulage than for roof-fall accidents, while the number of men killed by haulage is second only to the number killed by roof falls.

Jan 1, 1939

By R. W. Stahl

Coal mining has been revolutionized by the continuous miner. This machine has replaced, or has combined into 1, 3 former operations: Cutting, blasting, and loading. During the 25-year period before this machine was introduced, advances had been made in transportation, but the actual "coal getting" remained virtually the same. As frequently occurs, the multiple-purpose continuous miner introduced a new hazard--more rapid liberation of methane. The coal output formerly obtained from 10 to 20 working places might now be obtained from 1. It is true that circulation of air was generally increased; but the bulk of this machine virtually precludes continuous flow of air across the face, where gas may accumulate. Apprehension about this possible hazard led the Bureau of Mines to test face atmospheres during operation; and Report of Investigations 5288, Methane Buildup During Cutting and Continuous Mining Operations (published in 1956), presents proof that real danger may be present in many otherwise well ventilated mines.

Jan 1, 1958

By T. L. Marchewka

As part of its program to conserve the Nation's natural resources by developing improved performance materials, the Bureau of Mines, U.S. Department of the Interior, in cooperation with the U.S. Department of Energy, has conducted an investigation of materials of construction able to withstand the high temperature and hostile environments encountered in coal gasification units. Refractory pipe liners are required when extremely hot gases or abrasive solids are transported between processing units in the gasification plants. One promising technique for producing refractory pipe (or refractory pipe liners) is centrifugal casting. For this study, the effect of processing variables such as workability, additives, reinforcement and spinning time, and centrifugal force were evaluated using four commercial refractory concretes. In addition, data on characteristics such as strength, density, abrasion, and spalling resistance of 5-inch-diam refractory pipe were developed. Techniques for forming large-diameter (19-inch) refractory pipe also were evaluated. The test results indicated that all four refractory concretes could be made into strong, homogeneous pipe, but that optimum casting parameters had to be determined for each specific composition. The investigation revealed that the major controlling factor in the production of the centrifugally cast pipe was the workability of the refractory concrete.

Jan 1, 1979

By Anthony W. Sparks

The Bureau of Mines conducted tests designed to compare its breathing metabolic simulator (BMS) with other methods that are currently used to evaluate the performance of respiratory protective equipment. The BMS is a commercially developed device that uses a piston cylinder to simulate breath movement. Using a propane furnace that consumes oxygen and forms CO2, the BMS also simulates the respiratory metabolism of humans. The breathing and metabolic subsystems of the BMS are described in detail in this report. Results are compared from tests that used the BMS to evaluate respiratory equipment and from tests that used human subjects for the same purpose. The BMS was also tested against a pulsatile breathing machine (PBM) previously designed by the Bureau. Both machines were used to test respiratory equipment, and the test results are compared in this report. To illustrate typical applications of the BMS, the report briefly describes how the BMS was used to test two different types of closed-circuit respiratory apparatus, and the test results are presented. This research showed that BMS test results compared more closely to the results of tests that used human subjects than did results obtained using the PBM.

Jan 1, 1980

A revolutionary development in blasting materials has occurred in recent years. Ammonium nitrate, sensitized by the addition of a small percentage of No. (class) 2 diesel fuel or other suitable petroleum product, has been adopted as a low-cost, efficient blasting agent2 in a wide variety of mining, quarrying, and heavy construction operations. Moreover, the ready availability of the component supplies throughout the Nation, together with the ease of formulating them into effective blasting agents, has made it possible for the blaster himself to prepare the mixes at the site of use. Recently, most established explosives manufacturers have begun supplying premixed AN-FO (ammonium nitrate-fuel oil) or a comparable product to various mining operations. However, many individuals and small business establishments are marketing premixed products prepared in facilities that are often poorly constructed and poorly located. Although these blasting agents have partly or wholly displaced explosives such as dynamites in many applications, there are some blasting operations in which the fuel-sensitized ammonium nitrate agents do not appear to be well adapted. As long as the hazards they present are clearly understood and respected, ammonium nitrate-based blasting agents have important safety characteristics when prepared under competent factory control or field-mixed under equivalent close control. This publication attempts to summarize the knowledge of those hazards and to incorporate practical ways to cope with them.

Jan 1, 1963