Search Documents

By F. P. Haver

The purpose of this investigation was to determine the effect of common impurities, that is, oxygen, nitrogen, carbon, and iron, on the Brinell hardness of electrolytic titanium. On a weight basis, nitrogen had the greatest hardening effect, followed by oxygen, carbon, and iron in order. The hardening effects of oxygen and carbon were almost identical up to a concentration of approximately 0.1 percent by weight. Above this concentration, the relative hardening effect of carbon decreased rapidly, possibly because of its limited solid solubility in a-titanium. Hardness vs. composition curves for both oxygen and nitrogen were essentially straight lines over the range of Brinell hardness numbers (B.h.n.) covered in the investigation. The hardness of titanium was also determined as a function of the percentage of impurity atoms. On this basis, iron in concentrations up to 0.17 atomic percent had a greater hardening effect than either oxygen or carbon. INTRODUCTION Determination of the as-cast hardness of arc-melted titanium is a method of quality control widely used in industry. Numerous studies4/ have been made of the effect of impurities on the hardness obtained by this method. However, most of them have been based on the use of either iodide titanium or commercially pure Kroll sponge (B.h.n. >90), as a starting material.

Jan 1, 1959

By Ernest V. Deshayes

The Colorado Minerals Co. calcite properties in Archuleta and Hinsdale Counties, Colo., (fig. 1) were examined by Bureau of Mines engineers in 1943. The demand for optical calcite during the war prompted the examinations and resulting development programs on the Meadows and Seavy ranch properties near Pagosa Springs, Archuleta County. Development was begun on the Meadows property in November 1943 and continued to the Seavy ranch property. The work consisted of stripping the overburden from the calcite areas and excavating pits and trenches with a bulldozer. The pits and trenches exposing the most promising calcite veins were then deepened by hand, and one shaft was sunk to a depth of 30 feet. A total of 36 trenches and 9 pits were excavated by bulldozer and. hand methods (figs. 2, 3, and 4). The calcite deposits occur as veins and irregular bodies filling fractures in the Mancos shale of Cretaceous age. The fractures persist for considerable distances along the strike, although the calcite filling may not be continuous for more than a few feet. The widths of individual veins range from a few inches to several feet. The calcite crystals uncovered at the surface and in pits, trenches, and shafts were found to be unsuitable for optical purposes because of fracturing and color in the crystals.

Jan 1, 1949

[In selecting deposits for exploration projects, tabular deposits or large mineralized masses are favored because they may be explored systematically and because they afford the best opportunity for blocking out reserves in advance of mining whereas irregular, small pipes and scattered]

Jan 1, 1941

By G. W. Grove

The Joseph A. Holmes Safety Association acid the Holmes Association have fostered many chapters that have served as a medium in increasing safety in the mining industry. Details relating to the formation, operation, and achievements of the J. J. Forbes District. Council of the Holmes Safety Association, which operates in the Uniontown-Brownsville bituminous coal district of western Pennsylvania will be of interest to all who are striving to increase safety in mines, quarries, and in the oil fields. The Joseph A. Holmes Safety Association The Joseph A. Holmes, Safety Association' was organized in 1916 by 24 of the leading technical societies and mining organizations to perpetuate 'the memory of Dr. Joseph Austin Holmes, first Director of the United States Bureau of Mines.

Jan 1, 1929

By N. L. Wimmler

"INRODUCTIONSedimentary deposits of titaniferrous magnetite occur at various localities in the eastern foothills of the Teton Ranse in Deer Lodge County, Mont. The Choteau deposit was examined by a Bureau of Mines engineer in August 1942. An exploration project was recommended.Core drilling exploration was begun in June 1945; it was concluded in August 1945, Seventy-six holes were drilled. This report presents the data obtained by the Bureau of Mines exploration.ACKNOWLEDGMENTIn its program of exploration of mineral, deposits, the Bureau of Mines has as its primary objective, the more effective utilization of our mineral resources to the end that they make the greatest possible contri¬bution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, Chief, conducts preliminary examination, performs the actual exploratory work, and prepares the final, report. The. Metallurgical Branch, R. G. Knickerbocker, Chief, analyzes samples and performs beneficiation tests. Both of these branches are under the supervision of Dr. R. S. Dean, Assistant-Director. The field work was supervised by Earshel W. Newman, engineer in charge of the Helena Field Office. D. B. Hoiekvam was the project engineer; he provided most of the data used in the preparation of this report."

Dec 1, 1946

By G. S. Baur, J. W. Montoya, S. R. Wilson

Beryllium occurs in the Honeycomb Hills area in volcanic tuff similar to the more extensive berylliferous tuff occurring 20 miles east at Spor Mountain , Juab County , Utah . Samples from the two areas have been mineralogically examined to ascertain whether they have similar characteristics . The Honeycomb Hills samples showed the presence of beta- Be ( OH ) 2 , as well as an amorphous berylliferous substance , whereas in the Spor Mountain tuff the beryllium- bearing minerals are hydrated bertrandite and berylliferous saponite .

Jan 1, 1964

By W. A. Dunkley

During the past year and a half the Western United Corporation of Aurora , Illinois , has been distributing carburetted water ges from its Lockport , Ill . , plant , to an extensive territory , under an initial pressure ranging up to 90 lb.. per sq. in . The most distant distributing point on the system is at Harvard , Ill . , about 35 miles from the plant.. The territory supplied is approximately 85 miles long and 35 miles wide , the total mileage of rains being 1223 , or approximately 24 per cent of all the gas trains in Illinois outside the city of Chicago .

Feb 1, 1923

By G. E. McElroy, D. Harrington

In connection with the cooperative metal-mine dust and ventilation investigations of the U. S. Bureau of Mines and the U. S. Public Health Service , some underground data have been obtained with intent to ascertain the adaptability of the katathermometer for determining the comfort of working places in mines . This preliminary study indicates that the instrument will probably be useful for making routine determinations of comfort conditions in our mines , and that it may also prove an important accessory for investigative work on problems in ventilation and kindred subjects ; in both coal and metal mines , although the instrument should probably be altered somewhat for maximum utility under the varied conditions in the mines of the United States . The katathermometer is an instrument contrived by Dr. Leonard Hill , an eminent English physiologist , and its various features have been fully described by him in his book entitled " The Science of Ventilation and Open Air Treatment . " He made exhaustive experiments and concluded that the rate of cooling of the human body was the controlling factor in determining comfort or discomfort , and then set out to make an instrument that would measure this rate of cooling . The resulting instrument the katathermometer measures its own rate of cooling when its temperature approximates that of the human body and thus serves as an index of the rate of cooling of the body itself . - The instrument consists of an alcohol thermometer having a cylindrical bulb 1 inches long and 3/4 inches in diameter, and a stem about 8 inches long graduated from 95 to 100° F. This temperature range gives a mean temperature of 97.5° F. ( 36.5° C. ) , which is approximately that of the clothed body surface . The stem terminates in a small reservoir which serves the double purpose of acting as a safety overflow in case of overheating the bulb , and of insuring a regular rate of cooling by the time the meniscus has fallen to the 1000 point .

May 1, 1922

By Howard F. Carl

"INTRODUCTION Talc is a hydrous magnesium silicate mineral found throughout the world in deposits of economic importance. This mineral occurs in different physical forms and varying degrees of purity, both of which affect its ultimate commercial usage. Talc is used in finely ground condition by the ceramic, paint, paper, rubber, cosmetic, and other industries. Most domestic talc production is of this type. Talc also occurs, although much less frequently, in massive, fine-grained, fairly homogeneous bodies; the impure varieties are the familiar soapstones, and the purer form is frequently called ""steatite."" Because of certain properties, the purest grades of this massive variety have a monetary value about 20 times that of the ground talc.One desirable property of this massive talc is its amenability to accurate cutttng, machining, and working in many ways, similar to a hard wood or soft metal, and then firing without warping or appreciable shrinkage into a hard, refractory ceramic body. Consequently, shapes that cannot be formed conveniently by molding and pressing can be produced readily with ordinary machine tools. When talc is fired to about 1,100° C., it is converted to a ceramic body with certain very desirable physical properties. This fired material has a hardness and toughness frequently superior to steel. It is a refractory and an exceptionally good electrical insulator. When formed from a high-grade talc essentially free from iron, it has unusually low dielectric losees, even at very high frequencies."

Feb 1, 1945

By A. L. Engel

In the period of 1942-1945, medium-grade, oxidized, lead-silver ore was mined and shipped from the Diamond district near Eureka, Nev. An encouraging tonnage of low-grade ore was developed during these operations and partly blocked-out for future mining. If the low-grade ore could be treated profitably, further development of the district would result, and production of an important strategic metal might be increased. A representative sample of Diamond district ore was obtained through the Reno office of the Mining Division for the studies described in this report. The sample consisted of lumps and fines of a highly altered siliceous rock containing much earthy red hematite and some granular black hematite. Examination with the binocular microscope showed the lead carbonate mineral, cerussite, in seams and disseminated in the hematite. No zinc or silver minerals were identified, and no sulfide minerals were present. Analyses of the ore showed:

Jan 1, 1951

By M. J. Ferrante

Relative enthalpies of high-purity disodium hexatitanate (Na2Ti6013) were measured at the Bureau of Mines to provide new thermodynamic data needed to advance the technology of materials. Measurements from 298.15 to 1,478 K were made by drop calorimetry with a copper block. Tabulated values are listed for the standard relative enthalpy, heat capacity, en-tropy, and Gibbs energy function between 298.15 and 1,500 K. Enthalpy data are also given in equation form and are combined with thermodynamic data from the literature to derive values of standard enthalpies of formation, Gibbs energies of formation, and logarithms of the equilibrium constants of formation. Similar calculations were made for the reaction of Na20 with Ti02.

Jan 1, 1986

By B. I. Ferber

Sodium chloride aerosol was employed to determine respirator filter penetration in a manner suitable for use in Bureau of Mines approval and certification procedures. The aerosol was produced by an ultrasonic generator and treated to yield the proper conditions of relative humidity, particle size, and concentration. Respirator filters were exposed to the aerosol; filter penetration (down to 0.02 percent) was determined with a flame photometer. Results are comparable with those obtained in another laboratory using different equipment.

Jan 1, 1970

By M. M. Tilman

The objectives of this research were to determine the practicability of using cobalt as a means of controlling the amount of ferrite in the micro-structures of semiaustenitic stainless steels, and to determine the effects of reduced ferrite content on mechanical properties of these steels. Cobalt additions of up to 3 weight-percent were made to type 17-7 PH2 (AISI 631) stainless steel. Ferrite contents were determined for alloys in the aged condition, and for alloys quenched from the hot working temperature. Ferrite can be completely eliminated from the microstructure of 17-7 PH stainless steel by additions of cobalt, but complete elimination of the ferrite phase results in lower tensile strength, yield strength, and hardness. Tensile properties, hardness, and impact strength were determined for aged material. A subzero temperature treatment before heattreating was necessary to obtain maximum strength in the alloys containing cobalt. Addition of 2 weight-percent cobalt enhances mechanical properties of 17-7 PH stainless steel.

Jan 1, 1968

By Henry J. Kellner, Michael J. Brnich

This U.S. Bureau of Mines report addresses issues involved in using a limited number of training apparatus to give hands-on self-contained self-rescuer (SCSR) training to a succession of miners, and provides guidance regarding methods for minimizing the spread of infectious diseases. Procedures used for preventing the spread of infectious organisms in dentistry, cardiopulmonary resuscitation (CPR) training, and scuba training are examined. The sanitizing methods of three organizations that require individuals to insert the mouthpiece as part of the SCSR donning sequence are discussed. It was found that each of these organizations was able to render their mouthpiece assemblies microbe free simply and inexpensively.

Jan 1, 1989

By Wilbur I. Duvall

A linear array of shot and gage holes 30 feet deep in a granite outcrop was used to compare the size and shape of radial strain pulses produced in the rock when short cylindrical charges of cast composition B were detonated axially or at one end. The axially detonated charges produced radial strain pulses that had shorter rise times and larger peak strain than the strain pulses produced by end detonated charges.

Jan 1, 1965

By John H. Thompson

Recent studies ** at the Pittsburgh Experiment Station of the Bureau of Mines have revealed some interesting facts as to the probable behavior of steamed coke in the blast furnace . The literature on the chemistry of the blast furnace was tho roughly reviewed , and with this information in mind , the probable behavior of the coke sulphur in the blast furnace was deduced . Enough small - scale tests were conducted to furnish a check on most of the important deductions , and the conclusions derived therefrom accord with what is already known in regard to the forms of sulphur in coke , and fit in well with the general opinion concerning blast-furnace reactions .

Aug 1, 1923

By A. L. Engel

[This report describes preliminary tests of samples from six deposits of oxidized copper ores .in Nevada. The tests for the most part were confined to laboratory-scale acid leaching to extract the copper.'The exceptions consisted of flotation tests to demons' ate the possibilities of treating the ore by that method. The samples tested were representative of oxidized copper ores from six counties in all parts of Nevada. The results obtained by the preliminary tests described were indicative of the extractions of copper to be expected, In the five leaching experiments, the approximate consumption of acid was also indicated.]

Jan 1, 1953

By Joseph A. DeCarlo

The annual survey of the oven-coke industry by the Bureau of Mines, United States Department of the Interior, described in this report shows that 79 plants were operating in 22 States December 31, 1956. On that date 15,923 serviceable ovens existed, with a maximum total annual coke capacity of 79,965,100 net tons, and 631 new ovens were under construction. Their annual coke capacity was 3,307,300 net tons. The number of serviceable ovens in existence relates only to those capable of producing coke and does not include (1) any ovens that were blanked off or retired permanently in batteries that were operating December 31, 1956, and (2) ovens that had been demolished and were being rebuilt on that date. For this reason, the number of ovens at furnace plants reported by the Bureau of Mines at the end of each calendar year differs from the number reported for the same group by the American Iron & Steel Institute, as the institute includes ovens being rebuilt.

Jan 1, 1958

By Hsin Wei Wu

A real-time Diesel Particulate Matter (DPM) monitor has been developed on the basis of the successful National Institute of Occupational Health and Safety (NIOSH) designed Personal Dust Monitor (PDM) unit. The objectives of a recently completed Australian Coal Association Research Program (ACARP) study were to modify the PDM to measure the submicrometre fraction of the aerosol in a real-time monitoring underground instrument. Mine testing focused on use of the monitor in engineering evaluations to determine how conditions can be improved. Studies, including a selection during Longwall (LW) moves as described in this paper, demonstrated how DPM concentrations from vehicles fluctuate under varying ventilation and operational conditions. Correlation between the current SKC DPM measurement system and real-time DPM monitors were conducted and results from six mines show a correlation between elemental carbon (EC) and the new monitor DPM mass ranging from .51 to .81 with R2 >.90. These differences are suspected to be due to variations from mine to mine in aspects such as mine atmospheric contamination, vehicle fleet variations, fuel type, engine maintenance, engine combustion efficiency, engine behaviour or interference from other submicrometre aerosol. Real-time monitoring readily reflects the movement of individual diesel vehicles and allows pin-pointing of high exposure zones such as those encountered where various vehicles work in areas of constrained or difficult ventilation. DPM monitoring approaches that have been available for some time based on shift average monitoring do not readily allow successful engineering evaluation exercises to determine acceptability of pollution levels. Identification of high DPM concentration zones allows efficient modification of mine ventilation, operator positioning and other work practices t o reduce miners? exposures without waiting for laboratory analysis results.

Jan 1, 2010

By Andrew B. Cecala

As deeper seams are continually mined, methane liberation will continue to increase and must be monitored effectively. To effectively monitor and develop appropriate control technology, methane-liberation patterns must be known. The Bureau of Mines recently completed a study to identify specific patterns of face methane liberation during long- wall mining. Both of the longwall faces surveyed had high methane liberation rates. At one longwall face, most of the methane was liberated during cutting of coal by the shearer mining machine. At the second face, a significant portion of methane was emitted from the face and floor. An effective methane-monitoring system would be different for each longwall panel because of the differences in how the gas is released along the face.

Jan 1, 1985