Search Documents

By L. C. Brichta

During a study of the Badger-Peacock area from October 1950 to June 1953, the Federal Geological Survey and the Federal Bureau of Mines completed nearly 98 miles of resistivity profiling and drilled 96 test holes aggregating 17,628 feet of bore, In addition, seismic profile measurements were made along 8 traverse lines for an aggregate length of about 16,600 feet. The geophysical surveys were conducted by the Geophysics Branch of the Geological Survey; the drilling was done by the Bureau of Mines. Electrical-resistivity measurements disclosed 21 low-resistivity anomalies and 1 high-resistivity anomaly. Correlation of the resistivity data with the geological information revealed by the drilling disclosed that the low-resistivity anomalies indicated either slumped shale deposits in limestone sinks or undisturbed deposits of shale lying in erosional depressions in the limestone. The high-resistivity anomaly indicated hard, undisturbed limestone at or near the surface.

Jan 1, 1958

By D. J. Bauer

The Bureau of Mines has conducted extensive studies on the recovery of alumina from kaolinitic clay by a HCI leaching-HCI sparging process. The current study reports a modification of the process, which involves a double-leaching system. The first leach of the calcined clay is made at as high a HCI acid strength as possible so that the dissolution of aluminum chloride hexahydrate (AlCI3*6H20) is suppressed, Most of the impurities, but very little aluminum, are soluble in the strong acid. After liquid-solid separation and washing, the solids are leached with recycled weak HCI, which dissolves the AICI3'6H2O. The pregnant liquor is separated from the gangue, and AICI3'6H2O is crystallized from solu-tion by injecting HCI gas. A proposed flowsheet is presented, and the effect of bleedstream size on AlC13'6H20 purity is discussed.

Jan 1, 1984

By C. M. McCulloch, Maurice Deul

A geologic study of Mines 32 and 33 in Cambria County, Pa., was conducted as part of a methane control research program. Areas of high methane emission and roof instability are encountered which are related to the structural and stratigraphic features that characterize the geologic setting of these mines. Locally the folds trend N 20° E ±2°, the direction of the butt cleat in the Lower Kittanning coal. The face cleat strikes at N 69° W ±2° and the systematic rock joint in the surface bedrock strikes N 67° W ±2°This suggests that a directional stress oriented N 70° W produced the folds and influenced the directions of coal cleat and systematic joint sets. Analysis of SLAR indicates three directions of prominent regional lineation: N 39° E, N 31° W, and N 70° W. Little gas was encountered during development mining; large volumes of gas are encountered when roof falls. Most of the gas comes from strata above the mined coal; therefore, to control methane, roof instability must be controlled. Roof falls and high rates of methane emission are most likely where less than 30 feet of many thin layers of limestone, shale, and sandstone occurs between the Lower Kittanning coal and the next coal and in zones along the margins of a sandstone channel.

Jan 1, 1973

By D. G. Puglio

This Bureau of Mines study covers 25 underground mines that were active in the Upper and Lower Freeport and Lower Kittanning coalbeds in 1976. The coal ranges from low to medium volatile in rank; its primary use is for steam generation. Seven mines emit more than 100,000 cfd of methane gas; those mines are the deepest and largest producers. The methane gas content of three core samples of the Lower Kittanning coalbed was estimated by the direct method. A sample from a depth of 320 feet contained 0.5 cu cm of gas per gram, at 620 feet there was 0.8 cu cm of gas per gram, and at 1,060 feet there was 11 cu cm of gas per gram. These results suggest that methane control problems will be encountered in the future as deeper coal is mined.

Jan 1, 1979

By W. C. McBee

A family of modified-sulfur cements has been developed by the Bureau of Mines for the preparation of construction materials with improved properties. Various types of sulfur cements were prepared by reacting sulfur with mixtures of dicyclopentadiene (DCPD) and oligomers of cyclopentadiene (CPD). Durable cements were prepared with structural characteristics ranging from rigid to flexible. These cements were used to prepare corrosion-resistant materials for use in a wide variety of industrial applications where resistance to acidic and salt conditions is needed. These materials were prepared as rigid concretes, flexible pavings, spray coatings, and grouts. Production of modified-sulfur cements in a commercial-size plant was demonstrated.

Jan 1, 1981

By C. W. Owings

"Coal may be and has been hauled safely at approximately the same cost with permissible2 storage-battery locomotives as with trolley, cable-reel, crab-reel, or nonpermissible storage-battery locomotives. While in general, thinking mining men readily admit the relative safety of the permissible storage-battery locomotive there are some persons who question the safety of this type; however, the greatest opposition to the widespread use of storage-battery locomotives is from those who believe them to be more expensive to operate and to be more expensive in first cost than the trolley or cable-reel locomotive. Data collected during a comprehensive study- of storage-battery and wired transmission of power in some Pennsylvania and West Virginia coal mines indicate that there is but little difference between the cost of hauling with cable-reel or with storage-battery locomotives. It would appear that if this fact were mere generally known mine operators of the more progressive type would install such equipment and avail themselves of greater safety in hauling coal.The need for greater safety in haulage in coal mines is readily understood when it is considered that during the 12 month period, July 1, 1929 to June 30, 1930, trolley or cable reel gathering locomotives caused four explosions in which 407 lives were endangered, 11 persons were injured, and 30 lives were lost. Still another disaster was averted by the vigilance of a fire boss, who discovered a stratum of gas 3 feet thick at the top of an entry into which a gathering locomotive was about to enter. Other explosions not resulting in any fatality probably have not been reported. In addition numerous fires have been caused by trolley or cable-reel locomotives, and these fires probably would have been avoided had permissible storage-battery locomotives been used."

Nov 1, 1930

Laboratory tests were conducted by the U.S. Bureau of Mines to determine respirable dust reduction effectiveness of and interaction between face airflow and water sprays for a continuous miner. Increases in exhausting face ventilation from 3,000 to 9,000 cfm, in waterflow from 15 to 35 gpm, and in water nozzle operating pressure from 80 to 200 psi were evaluated. Results indicated that airflow had the greatest individual impact on reducing dust levels, with concentrations at return and operator sampling locations reduced by as much as 57% and 99%, respectively. Regression modeling was utilized to predict dust concentrations over the range of values tested for the control parameters. Interactions between the control parameters were significant and often defined an optimum level where further increases in that parameter failed to produce additional dust reductions. Increasing airflow to 8,400 cfm, waterflow to 25 gpm, and water pressure to 140 psi typically reduced dust concentrations at operator and return locations. Application of a control parameter above these levels can provide additional dust reductions if used in conjunction with appropriate levels of the other two control parameters. Otherwise, higher operator dust levels may result and can be attributed to increased rollback and/or airflow turbulence.

Jan 1, 2010

By R. E. Heithecker, D. B. Taliaferro

"INTRODUCTION Recovery of core specimens from subsurface formations and their subsequent analysis are important aids in efficient development and operation of oil and gas fields. Gore specimens first were obtained mainly for the geologic information they revealed; now they are analyzed to determine many of the physical characteristics and conditions of the subsurface formations as well. Cores recovered from the producing formations may be analyzed for porosity, permeability, oil content, ""connate"" water content, and other physical and chemical properties of the formation, all to the end of furnishing enough data for making reliable estimates of the quantity and avail¬ability of oil and as within a reservoir and in devising efficient means for their withdrawal.Examination of bottom-hole samples of oil gives valuable information concerning the amount of gas in solution in the oil within the reservoir and the resultant shrinkage of the oil when the gas is released. Producing characteristics of reservoirs nay be determined by means of subsurface pressure and temperature gages and measurements male at the wellhead; however, unless reliable core analyses are available, these data have only limited use in any quantitative study of reserves. In such a study the quantity of oil, gas, and water contained in a unit volume of the reservoir formation is extremely important. Although reliable methods of analyzing cores have been developed and the data thus obtained are valuable, their applications become more limited or reservoirs at higher temperatures and pressures are discovered. This condition results almost entirely from the fact that in recovering a core from a formation of high pressure and temperature by present methods a large part of the fluid content of the core is lost or contaminated to an unknown extent. For a number of years most petroleum engineers have held that if this loss and contamination of the fluid content of a core were eliminated, the value of core analyses would be increased greatly."

Nov 1, 1939

By B. C. Burgess

This paper, describing the milling practices at the Minpro plant of the Tennessee Mineral Products Corporation, Spruce Pine, N. C., is the first of a series being prepared by the U.S. Bureau of Mines on feldspar milling methods and costs in the various feldspar producing areas in the United States. It describes not only the latest practices in feldspar grinding but includes studies of the cost of producing ground feldspar. These cost studies, obviously of interest to every consumer and purchaser of feldspar and to all feldspar grinders, are also of value to the small operator, who is generally prone to understimate his real costs. It describes the latest practices in feldspar milling and includes detailed costs of grinding. The cost tabulations presented show operating expenditures only and not total production costs. Details of costs are given only to the extent that they are essential to the technical discussion and study of the methods employed. A description of the recently installed milling unit for the preparation of granular glasspar by graded crushing, and magnetic separation is of particular interest. It illustrates how highly specialized feldspar milling has become, and to what an extent grinders are going to supply consumers with the products best suited for their particular needs.

Jan 1, 1931

By W. C. Smith

This Bureau of Mines report discusses how pull-test data can help establish polyester resin column length criteria for roof bolts in evaporite minerals. The study evaluates the effectiveness of partial to full columns of resin in anchoring 4-ft, No.6, grade 40 rebar roof bolts in potash, salt, trona, gypsum, and borate mine roofs. Pull tests were performed on over 600 roof bolts in 11 evaporite mines. Column lengths ranging from 6 to 48 in (fully grouted) were evaluated for each test site. In general, comparative results among all test sites indicate that pull-out loads in excess of 10 tons (force) were attained with resin-grouted bolts having 13 to 75 pet less than a full column of polyester resin. Ten tons (force) of load-carrying capability compared favorably, in terms of strength, with the calculated yield strength of the rebar used in the tests, which was 8.8 tons (force). The site-specific nature of each test site, due to the unique combinations of geology, mine-induced stresses, and other unknown parameters, prevented the establishment of valid generic column-length criteria. For these reasons, data to evaluate resin-column-length effectiveness are best obtained on a mine-specific basis.

Jan 1, 1987

By William C. Cooley

Data on equipment and components which have been used in hydraulic mining experiments, tests, and operations were collected from the literature. Also data were obtained from U.S. manufacturers and suppliers of equipment which is potentially applicable and available in the U.S. for hydraulic mining. The data have been divided into 24 main categories (see the following page) and have been assembled on two-page data sheets which follow. Wherever possible, drawings or photographs are included immediately after each data sheet.

Jan 1, 1975

By Jasinder S. Jaspal

In underground room-and-pillar mining methods, the sectional conveyor belts are extended or retracted periodically to maintain shuttle car tramming distance to a minimum. A conventional conveyor belt extension or retraction is a heavy, arduous job that if mecahnized, has the potential to improve productivity and safety. To reduce the burden of heavy work of this activity and mechanize it, the Bureau of Mines developed a conveyor belt service machine (CBSM) through a research contract with Tractor MBA. The CBSM is a self-contained, battery-powered, rubber-tired vehicle capable of handling, storing and transporting conveyor belting, wire rope, and associated belt structures in seams as low as 48 in. Belt extensions and retractions are accomplished by moving the tailpiece of a belt conveyor with the CBSM to the next position while dispensing or retrieving the belt, wire rope, and associated belt structures. The CBSM improves the belt extensions and retractions by making them easier and faster, and it utilizes fewer workers. The CBSM was surface tested at the Bureau's Mining Equipment Test Facility (METF) to evaluate its performance and reliability. Modifications were made to the CBSM to correct deficiencies found during surface testing.

Jan 1, 1988

By Wilbert J. Huff, Raymond H. Moore

"Black powder is employed widely in peace and war. Its properties are therefore of considerable interest to many. The Bureau of Mines frequently is asked to furnish information on its use and safe handling in the mining and mineral industries in times of peace and is now engaged in studies of its application to the arts of war.Black powder has been the agent in many accidents - some very disastrous - and its handling and use are deemed very hazardous. The belief is widespread that the hazards are due principally to the ease with which the powder is ignited by a hot spark or flame in contradistinction to high explosives; these usually are ignited only with difficulty, and some burn incompl0tely and to a certain extent are self-extinguishing. Primary precautions, .therefore, should be taken to prevent the access of heat, spark, and flame.In black powder manufacturing operations a frequent source of disaster is the initiation of fires and explosions in the wheel mills in which the sulfur, charcoal, and nitrate are incorporated. Long experience has indicated that the wheel mill probably will fire if the powder is not kept moist enough; manufacturing supervision calls for the maintenance of a minimum moisture content, at least during the milling. Accidents occur elsewhere in the manufacturing line, and in an endeavor to minimize these, particularly those happening in corning mills, one of the writers suggested many years ago that a suitable humidity be maintained in other operations in the hope that it would serve protectively as in the wheel mill. The experience of one company for many years with this practice was favorable. It seemed desirable therefore, to explore the question experimentally."

Nov 1, 1944

By A. J. Miscoe

A unique machine for inducing bending fatigue in wire ropes was built at the U.S. Bureau of Mines' Pittsburgh Research Center. This machine can produce nine levels of degradation through repetitive cycling of long samples of wire ropes of the types used in the mining industry. This report provides an analysis of the results of the first wire rope to be fatigued on this machine. These results have indicated that as a wire rope accumulates bending cycles, its strength first decreases because of wear and then in-creases due to cold working of the wires. As the amount of cold working increases, more and more of the embrittled wires break and the strength of the rope decreases rapidly. In this test, application of several of the regulatory retirement criteria to various sections of the rope suggests that there may be some inconsistency among them.

Jan 1, 2010

By J. L. Reuss

The Bureau of Mines investigated the technical feasibility of smelting copper concentrates containing chalcocite (Cu2S) and native copper using nonpyritic sulfur-bearing materials to aid matte formation. The procedure consisted of combining various proportions of commercial chalcocite concentrate, smelter slag, fluxes, and matte-forming constituents to produce charges of comparable compositions. The mixtures were charged in fire-clay crucibles and smelted in an induction furnace at 1,300° C. The research proved that either sulfur or gypsum can replace pyrite as a matte-forming material, and that gypsum produces an exceptionally high-grade copper matte. The addition of small quantities of metallic iron to the nonpyritic smelting charge furthers the removal of sulfur, improves the recovery of copper, and makes it possible to utilize gypsum as the exclusive flux and matte-forming ingredient, thereby eliminating the necessity of adding limestone.

Jan 1, 1968

By D. E. Shanks

As part of its goal to help maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines, U.S. Department of the Interior, is investigating a fused-salt electrolytic procedure for producing zinc metal. A previous report described preliminary, small-scale work on the fused-salt electrolysis of ZnC12. The present report covers a more detailed investigation of the properties of ZnC12-alkali metal chloride electrolyte systems in relation to the production of zinc metal and also discusses electrolysis in largescale, internally heated cells. The effect of composition on bath stability, current efficiency, cell voltage, and liquidus temperature was determined for the ZnCla-NaC1-KC1, ZnC12-NaC1-LiC1, and ZnC12-KC1-LiC1 electrolyte systems. An electrolyte com-posed of 38 mole-pct ZnC12, 31 mole-pct NaC1, and 31 mole-pct KC1 gave the best overall results. Sludge (ZnO) formation in the ZnC12-NaC1-KC1, ZnC12-KC1-LiC1, and ZnC12-KC1 systems was investigated during prolonged electrolysis. The ZnC12-KC1-NaC1 electrolyte showed the least sludge formation. A 1,500-amp cell was operated using the ZnC12-NaC1-KC1 electrolyte at 500° C. Zinc metal was produced at the rate of 4.0 lb/hr with a current efficiency of 95 pct.

Jan 1, 1979

By P. F. Sands

This U.S. Bureau of Mines report reviews the state of the art in blind pneumatic stowing of backfill in voids in abandoned coal mines. It contains a short history of the development of pneumatic equipment in mining and four recent case histories of blind pneumatic stowing. Limitations of pneumatic stowing in terms of equipment wear, costs, backfill material, and methodology are discussed, and some new procedures and designs are reviewed. A bibliography covering pneumatics in mining is included also. This report provides background for the preparation of a Bureau test program in which the variables affecting the efficiency of pneumatic backfilling will be studied using a full-scale surface test facility.

Jan 1, 1990

By P. G. Kovalchik

Safe electrical operation of shuttle cars depends upon maintaining the trailing cable's conductor temperature below 90° C. However, trailing cables are wound on and off reels, which changes the heat transfer characteristics of the cable-reel system. Derating factors for trailing cables are an attempt to adjust for this changing heat transfer mechanism in a practical way. The U.S. Bureau of Mines conducted research to determine acceptable derating factors for reeled mine trailing cables, using four cable-reel combinations, representative of industry usage. Cables were continuously and intermittently loaded at different duty cycles with direct currents of different magnitudes. Relationships between the average temperature rise and current load were established for each layer of each cable. Two models were constructed; one used empirical data from the continuous and intermittent load tests, and the other was based on thermodynamic theory. Results obtained from the theoretical model were compared with those from the empirical model for the rated temperature rise of the cable. Both models can be used to simulate a variety of test conditions including those that normally cannot be conducted in the laboratory. This information was used to determine acceptable derating factors for each layer of these cable-reel combinations.

Jan 1, 1994

By John Ward Smith

This paper describes and evaluates a method that the Federal Bureau of Mines used to determine the ultimate composition of the organic material in 10 samples of oil shale from the Mahogany zone of the Green River formation in Colorado and Utah. Since interest has centered on the Mahogany zone, the richest section of the deposit, these 10 samples were chosen to provide a broad representation of this zone with the objective of obtaining generally valid ultimate composition values. The most probable organic composition for the Mahogany zone and the 95-percent confidence limits for each component average (in weight-percent of organic material) are: Carbon 80.5 ± .4 Hydrogen 10.3 ± .1 Nitrogen 2.4 ± .1 Sulfur 1.0 ± .1 Oxygen 5.8 ± .5 As only minor variations in composition were observed, the organic material of this particular bed is quite similar over a wide geographic area.

Jan 1, 1961

By Will H. Coghill, C. O. Anderson

In July 1921 , we were assigned by the U. S. Bureau of Mines to an investigation of milling methods in the Tri - State zinc district ( Missouri -Kaneas- Oklahoma district ) . The work has progressed without interruption , and about onehalf of the funds allotted for it has been expended . This preliminary statement abcut the nature of the work and the results so far obtained , has been prepared for the information of the operators , and through their assistance to insure the greatest possible progress during the remainder of the work . A general survey of the district was made , and many of the mining companies cordially offered the facilities of their plants for the investigation . The work was finally centralized at the plant of the 0. M. Bilharz Mining Co. Its manager , F. H. Gartung, and his successor , O. W. Bilharz , have been especially helpful , also the millmen at this plant and elsewhere have rendered assistance without which the work could not have advanced . The Missouri School of Mines and Metallurgy , Rolla, Mo. , and the Miami School of Mines , Miami , Okla . , have given hearty cooperation . The Webb City Iron Works and the Joplin Supply Co. donated some necessary apparatus .

Jan 1, 1922