Search Documents

By G. H. Wigton

This paper, describing the concentrator practice of the Chief Consolidated Co., is one of a series being prepared by the United States Bureau of Mines. The concentrator adjoins the town of Eureka, Utah, in the Tintic mining district. The Chief Consolidated, Eureka Lilly, Plutus, and Grand Central mines, all of which are owned or controlled by the Chief Consolidated Mining Co., are the principal sources of milling ore. The ore is transported from mines to mill by railroad. Although all the mines are within 3 miles of the mill, the railroad distance varies from 1 mile to 12 miles.

Jan 1, 1930

By William L. Crentz

Late in the nineteenth century en active coal-mining industry was begun in the Lower Freeport bed near Reynoldsville, Pa., where the bed thickened to more than 10 feet in places . The coal was readily accepted as an excellent steam fuel. Much of the thick coal his been depleted, but there are many areas where the deposit averages about 14 feet in thickness. As the more desirable mining sites were worked out in the Lower Freeport bed, other beds were exposed from which will come the county's major cowl production in future. The Lower Freeport bed is still the most important bed in Jefferson County from a production standpoint. The Lower Kittanning bed is second. Sporadic mining is being done in the Upper Freeport, Upper Kittanning, Middle Kittanning, Clarion, and Brookville beds. Strip mining has permitted recovery of much coal that could not be mined profitably by conventional underground methods.

Jan 1, 1953

By Constantine C. Popoff

The Hermada antimony deposit is in the Sewtooth Range in southwestern Idaho, about 77 miles by road northeast of Boise. Stibnite mineralization occurs over an area one mile wide from west to east and two miles long. It is locally referred to as the Swanholm district. In 1947 high- grade stibnite ore was discovered on the East Fork of Swanholm Creek. Since then, ore in commercial quantity has been produced by the Hermada Mining Co. The total output for 1947-50 was about 5,000 tons of ore, containing 640 short tons of antimony metal.

Jan 1, 1953

By Frank E. Cash

Although during the past 10 years Alabama has attained an enviable position by its coal-mine accident experience and, like most of the other coal-mining States, has made progress in the safer operation of coal mines, there is still room for improvement, which can be realized only by still greater efforts on the part of employees and employers. From 1993, when accidents were first recorded by the Alabama State Mine Inspection Department, to 1934, inclusive, 3,451 men lost their lives in the production of 569,722,676 tons of coal. The primary purpose of this report is to bring to the attention of the mining industry in Alabama end elsewhere statistics of fatal accidents for 1931-34, with the hope that a study of the causes may lead to reduction of similar accidents in the future.

Jan 1, 1936

By James M. Link

Underground coal mining is the most hazardous industrial occupation in the United States.. Haulage accidents in underground coal mines contribute substantially to the occupational hazards of this type of work. In an effort to improve mine safety, a completely hydraulic transport system has been designed to move coal from the mine face to the preparation plant. The capital investment for the hydraulic haulage system is great, and the size of the mine developed for this study is large. Mine production for the conventional haulage mine is 1. 1 million tons of clean coal per year, while the hydraulic haulage mine will produce over 1.6 million tons of clean coal per year. Safety statistics for a number of mines of this size are shown.

Jan 1, 1975

By Robert L. Skaggs

Sixteen nonaqueous techniques conceived to replace the current aqueous scheme for separating hafnium and zirconium tetrachlorides were re- viewed and evaluated by the Bureau of Mines. The methods are divided into two classes: separation by fractional volatilization of the tetrachlorides, which takes advantage of the higher volatility of hafnium tetrachloride; and separation by chemical techniques, based on differences in chemical behavior of the two tetrachlorides. The criteria used to evaluate separation methods were temperature, pressure, separation factor per equilibrium stage, complexity, compatibility with existing technology, and potential for continuous operation. Three processes were selected as being most promising: (1) high-pressure distillation, (2) extractive distillation from a molten salt, and (3) preferential reduction of gaseous ZrC14. Any of the proposed nonaqueous Hf-Zr separation schemes must be supplemented with additional purification to remove trace impurities.

Jan 1, 1984

By Lyman Moore

This Bureau of Mines report describes 2nd evaluates iron ore resources in California and Nevada and analyzes the California and Japanese iron ore markets in which these resources will be used. The competitive position of California-Nevada ores, in these markets, was estimated by comparing regional iron ore prices, production costs, and transportation costs with those of foreign suppliers. Resources were determined to be sufficient to produce the equivalent of 585 million tons of 64-percent iron pellets at a price of less than $15 per ton delivered at California ports. Much higher tonnage could be produced at higher prices. Iron ore requirement of the California iron and steel industry will increase to an estimated 15.9 million tons by the year 2000. A study of the iron ore production potential of California-Nevada deposits and of out-of- State sources indicated that this ore requirement can be supplied most economically by California-Nevada ores. Iron ore import requirements of the Japanese iron and steel industry will increase to an estimated 150.0 million tons by the year 2000. A study of price trends in this market indicated that very little California-Nevada iron ore will be sold in Japan after 1973 when existing sales contracts expire. Iron ore-exports might be economically possible if ore could be transported from California to Japan at ballast rates as backhaul on existing petroleum shipping.

Jan 1, 1971

By Lloyd Williams

1. The investigation shows that the Poplar Creek and Big Mary beds contain the largest known recoverable reserves of coal in Morgan County, Tenn. The Poplar Creek bed has been the most productive. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 96 million tons, as of January 1, 1954. Of this total, 59 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By Robert J. Hundhausen

The Young America lead-silver-zinc mine in Stevens County, Wash., was investigated by the Bureau of Mines during parts of 1946, 1947, and 1948. Results of the investigation are described herein. The mine is 1/4 mile northeast of Bossburg, Wash., the nearest railway station. An excellent paved highway (No. 22) connects Bossburg with Colville, Wash., 23 miles to the south. The property was located in October 1885. It is credited with a production of 2,178 tons of shipping ore since 1901. The shipping ore averaged 7 percent lead, 7.7 percent zinc, and 16.1 ounces silver per ton. The property is under lease and option to Walter E. Morris and Perry Leighton of Colville, Wash. The deposit crops out on a steep limestone bluff overlooking the Columbia River. The country rock is a highly metamorphosed, brecciated, marbleized limestone (Northport formation).

Jan 1, 1949

By Frank J. Wiebelt

Under a general program to extend the resources of mineral deposits, the Bureau of Mines examined the Quien Sabe antimony mine in October 1948. The preliminary evaluation demonstrated that a diamond-drill program was warranted co establish the tenor and persistence of the veins and permit an estimation of antimony reserves. The Bureau of Mines conducted a diamond-drilling program on the property from December 1949 to May 1950. Ten holes aggregating 2,483 feet were drilled. Nine of the holes encountered antimony-bearing vein material.

Jan 1, 1956

By P. L. Woolf, N. Bernstein, M. M. Fine

Continuous experimentation utilizing a 3- by 36 - foot rotary kiln was conducted to demonstrate the feasibility of simultaneous induration and reduction of magnetic taconite concentrate . Lignite , or lignite - anthracite mixtures , and green magnetite pellets (64.2 percent Fe , dry basis ) were heated in a rotary kiln to about 2,100 ° F. After separation from excess reductant , the product pellets were found to be highly reduced and acceptably hard . A total of 140 tons of prereduced pellets with an average Fe content of 79.0 percent was produced at Minneapolis and smelted in the Bureau's experimental blast furnace at Bruceton , Pa . Two additional supplies of prereduced pellets were obtained from The Steel Company of Canada , Ltd. , Hamilton , Ontario , which contained 83.8 and 91.3 percent Fe , respectively . Smelting of prereduced pellets was compared with that of unreduced pellets obtained from The Hilton Mines , Shawville , Quebec , and from the Erie Mining Co. , Hoyt Lakes , Minn . Blast furnace tests established that a substantial decrease in coke rates and higher production result from the use of prereduced pellets .

Jan 1, 1964

By Seth T. Reese

REPORTS received from operating companies by the Bureau of Mines, United States Department of the Interior, indicated marked progress in the reduction of injuries to employees in the coking industry in 1951 as compared with 1950. The fatality rate (0.14) per million man-hours of exposure declined 33 percent and was the second best performance since statistics on the industry were first collected in 1916. The nonfatal-injury rate (10.94), the best since 1940, declined 8 percent and was bettered only in 8 of the past 36 years. The nonfatal rate is based on all injuries resulting in loss of time for more than the remainder of the day on which the injury occurred. The exposure to hazard, as represented by the number of man-hours of work time during the year, was 7 percent higher than in 1950 and, except for the year 1943, was the highest since 1920. The fatality rate for men employed at beehive-coke ovens decreased 16 percent and the nonfatal-injury rate 23 percent, while the man-hours of work time or exposure increased slightly over 16 percent. The fatality and nonfatal-injury rates at byproduct ovens declined 33 and 2 ½ percent, respectively, while the number of man-hours worked increased 6 percent.

Jan 1, 1954

By S. H. Ash

THIS REPORT covers the third in a series of five projects into which the Conowingo tunnel system has been divided for geographical and practical reasons. It outlines the work constituting Project No.3 that consists principally of the following: (a) To sink the No. 15 shaft and extend the Alden, Sugar Notch, Baltimore No.2, and Laflin shafts from their present depths to tunnel level; (b) to drive a tunnel off these shafts to connect with the western end of the tunnel in Project No.1 (Lackawanna) and to a point 1 mile south of the No. 15 shaft; (c) to construct an emergency pumping plant at the No. 15 shaft, complete with 3 centrifugal pumps of 200-cubic-foot-per-second (c. f. s.) capacity each, and a discharge-water shaft and a discharge tunnel for conducting the water from the pumping plant into the Susquehanna River; and (d) to construct a lateral tunnel 1 mile long off the main tunnel in the vicinity of the No. 15 shaft, to be known as the Wyoming lateral. The project, as outlined, is a self-contained drainage unit that will permit unwatering inundated mines and safeguarding active mines in the Wyoming Basin of the Northern field and also will handle the water in the Lackawanna Basin, thus permitting the temporary pumping plant provided in Project No.1 to be discontinued. The pumps installed in the temporary pumping plant provided in Project No.1 can then be moved to the emergency pumping plants recommended in Projects Nos. 2 and 3, to be installed as the third or standby unit.

Jan 1, 1955

By Wilbert J. Huff

The organization of the'Explosives Division is indicated by the accompanying chart (fig. 1). As this has been discussed in a previous report3/, it will not be considered further in this report. The activities of the various units are outlined below. I. INFLAMMABILITY OF GASES AND VAPORS4/ Determination of the Explosion Hazards of Combustible Gases and Vapors Found in Mines and Industries The Explosives Division maintains, at the Pittsburgh Experiment Station, a laboratory specially equipped for the determination of the explosion hazards of combustible gases and vapors. Of particular importance, is the determination of the chemical composition within which explosions may occur and beyond which there is no danger of explosion, combustion or inflammation. These limits, known as the limits of inflammability, as determined by this and other laboratories, have been compiled in Bulletin 279 of this Bureau. The last revised edition (1931) of this bulletin has been exhausted. Since it was published, the Pittsburgh laboratory has determined the limits of about 40 combustibles and has ascertained more precisely and accurately many previously published limits.

Jan 1, 1938

By W. P. DYKEMA

This report gins the results of a study conducted hy the Ilnreau of Mines for the purpose of informing the petroleum industry on the recent progress in the de,·elopment nncl application of the absorption process for recO\·ering gasoline from natural gas. The work has been undertaken entirely with regard to plant practice and for the purpose of describing the features and the operation of units of the plants now in use, the improvements that have been made, and the reasons for any ehanges eontemplated by the engineers in eharge· of the plants studied. Throughout the United States the impro,·ements in the absorption process that are under consideration by engineers not only widen practice so as to include gases at all pressures and percentages of gasoline content, but seem to be dewloping definite standards as to dimensions of towers, l"elocities of flow, saturation of oi~ areas of eooling surfaces, and quantities of menstruum to be circulated. Although perfect practice has by no means been attained, the writer belie,·es thnt a description of the current practice at ,·arious plants, including those ob,'iously more efficient features that each plant hns <le\"eloped and uses at one or another stage of treatment, will intere;; t and possibly help all persons operating or designing absorption plants.

Jan 1, 1919

By J. W. Thompson

A contract stipUlating for the delivery of quantities of phosphate rock" f. o. b. mines," and stipUlating that" while this contract is in form an absolute sale for a fixed quantity in each year, it is mutually understood and agreed that the purchase is for the buyer's consumption and not for a sale; the buyer agreeing to give to seller the refusal of any surplus over and above the actual consumption. Buyer is at liberty to increase or diminish the quantity called for in any year, to the extent of not exceeding 10 per cent; provided that the quantity to be taken shall not be less than buyer's consumption; provided further that notice of such increased or diminished demand be given seller 12 months in advance of such change," is to be construed as a contract for the sale of stated quantities of rock, deliverable in approximately equal quantities during each year for the specified series of years, subject only to be increased or diminished after specified notice in any year, where the amount taken would not be les<; than the buyer's consumption, not exceeding 10 per cent, and the contract indicating that the rock was intended by both parties for consumption in the fertilizer plant of the buyer. but the quantity to be taken was not limited by the necessities of' the plant.

Jan 1, 1916

By Robert C. Merritt

This report describes laboratory as well as pilot heap leaching investigations of low-grade sandstone ores from Wyoming, New Mexico, and Colorado. Sodium carbonate-bicarbonate solutions containing sodium hypochlorite extracted up to 86, 54, and 16 percent U308 from Wyoming, New Mexico, and Colorado ores, respectively. Ammonium carbonate-bicarbonate solutions containing sodium hypochlorite were less effective at leaching these ores. Acid leach in replicate pilot plant testing resulted in U308 extractions of 96, 88, and 81 percent from the Wyoming, New Mexico, and Colorado ores. The development of cost-effective processes for extracting uranium from low-grade ore is essential to the assurance of a continuing domestic supply of uranium.

Jan 1, 1977

By L. F. Heising

The Bureau of Mines evaluated 42 composite samples from selected Michigan-Wisconsin iron formations by reductive roasting-magnetic separation and flotation at minus 325 mesh. Samples having poor to marginal response on initial examination by conventional methods were reevaluated by finer grinding, by reagent suite modifications, and by selective flocculation-desliming techniques. Results ranged from excellent on Menominee Range samples to relatively on Gogebic Range ores. Marquette Range samples ranged from responsive to nonresponsive, depending upon grain size and mineral association.

Jan 1, 1967

By C. T. Anderson

In July 1947, the U. S. Bureau of Mines, in cooperation with the Air Materiel Command, started an investigation of zirconium alloys with the object of determining the suitability of such alloys for high-temperature applications. This report covers the preliminary study of about 25 zirconium-rich alloy systems with respect to preparation, fabrication, tensile properties, metallographic structures; constitution, and heat resistance. Obviously, each system could not be investigated thoroughly, and this publication can be regarded only as a first approach. The more promising individual alloy systems will be studied in greater detail and reported in subsequent publications. The study of zirconium alloys on such a scale has been made possible by the U.S. Bureau of Mines developments in the past 5 years On producing zirconium metal. This basic process is similar to that developed by Kroll for producing ductile titanium metal and consists essentially of reducing zirconium chloride by means of molten magnesium. The Northwest Electrodevelopment Laboratory at Albany, Oreg., has produced several thousand pounds of ductile metal in this manner and has a pilot plant producing over 300 pounds of metal per week. Alloys were prepared by melting Bureau of Mines zirconium and the best available grade of alloying element in graphite, with suitable provisions for preventing oxidation. The ingots were quartered longitudinally and sheath-swaged at 850° c. to 3/8-inch diameter rod. Two of those rods were send to Wright Field for room-temperature and 1,200° F. tensile properties. The remaining two sections were used for metallographic, hardness, heat-treatment, and heat-resistance studies. The salient features of this investigation are summarized in table 1.

Jan 1, 1950

By L. M. Burman

The phase-boundary pressure required to maintain a natural hydrocarbon fluid in a single phase must be considered in planning the recovery of reservoir liquids by miscible-phase processes. The change in the phase-boundary pressure at reservoir temperature that results when a light component or a mixture of light components is added to a reservoir fluid is an especially important consideration. The cricondenbar pressure (maximum phase-boundary pressure) and the critical pressure are unique correlated pressures that have been utilized to calculate the change in phase-boundary pressure that may result when the composition of a reservoir liquid is altered by an additive. In this study one reservoir oil and three gas-condensate fluids are used as examples. Correlations pertaining to the critical and cricondenbar states in chapters 4 and 5 of Bureau of Mines Monograph 10 (3)5 were used to demonstrate how butane and lighter components added to these reservoir fluids affect their phase-boundary pressures.

Jan 1, 1962