Search Documents

By Deno Pappas, Chrisropher Mark, John Rusnak, Linda McWilliams

Mine planning for a new reserve is based on information obtained from exploratory coreholes. A critical component of an exploration program is the geotechnical evaluation. Poor assumptions about roof conditions greatly add to the risks of mining. Rock mechanics testing is central to a geotechnical exploration program. Typically, 3 to 5 uniaxial compressive strength (UCS) tests are made to characterize a particular roof unit at a given corehole. The average (mean) of these tests is taken as “The UCS” for that location. Isopach contour maps are then used to show spatial trends in roof strength. Two issues are raised by this traditional approach. The first is due to the large variability in UCS values that is typical even within a single unit from a single hole. The average UCS might be higher at Corehole A than it is at Corehole B, but the difference may not be statistically significant. The second issue is whether widely spaced coreholes can identify valid spatial trends in rock strength. The answer depends upon whether rock strength changes over distances that are longer or shorter than the corehole spacing. This is a classical geostatistical problem. While geostatics have been used to investigate many coal quality parameters, they have seldom been used to evaluate rock strength. This paper describes an extensive investigation of these issues conducted by the National Institute for Occupational Safety and Health (NIOSH) in collaboration with Peabody Energy. The study employed the Peabody Rock Mechanics Data Base which contains more than 10,000 individual test results. Data from four important roof units were subjected to statistical analysis: • Brereton Limestone above the Herrin 6 seam (Illinois) • Turner Mine Shale above the No. 9 Seam (Kentucky) • Sandstone above the Eagle Coal (West Virginia) • Shale above the Eagle Coal (West Virginia) The study did not find significant spatial trends in rock strength in any of the cases. Perhaps there are none, or perhaps the exploration coreholes were just too far apart to see them. These results have valuable implications for the design of geotechical exploration programs.

By Yumi Nakashima, Setsuo Maeda

Vibration magnitude and frequency of the z-axis vehicle seat are time-variant, which are influenced by not only vehicle vibration characteristics themselves but also road surfaces, speeds and the human body. There is little in the current reporting about evaluating and analyzing automobile seat vibration that focuses on the time-variant. Yaguchi et al.1 has proposed a method to evaluate automobile seat vibration that is based on judgments using a subjective mental state. Their method focuses on the time-variant magnitude of the peak frequency on a power spectrum density. However, their method has no consideration of all the frequency contents of the discomfort, nor comparison between different peak frequency vibrations. Suzuki2 has emphasized that the vehicle vibration should be judged by a series of vibration stimuli to evaluate, because the vehicle vibration is time-variant, which isn’t a matter of the relationship between a single vibration stimulus and a subjective response. He clarified that the human sensation to the vehicle vibration discomfort changes every moment showing the relationship between the frequency-weighted r.m.s. acceleration calculated every 5 seconds and the category judgment to vehicle vibration discomfort every 5 seconds. However, his study doesn’t show what parameter connects to the subjective final judgment to vehicle vibration. Therefore, we applied the method similar to ISO100563 considering the time-variant to the vehicle seat z-axis vibration evaluation. The new method for the vehicle seat vibration considering the time-variant was examined on the hypothesis that the final subjective evaluation must be conducted from the judgment summarizing a series of vibration stimuli. Methods The vibration bench system, which reproduces the movement of a vehicle floor, was used for the experiment with the single-axis (vertical direction) four-post road simulator system, which is usually used for a car, as shown in Fig.1. The experiment was done on the right side of the vibration bench using the floor vibration which was 5.5 minutes, 0.822 m/sec2 (Wk) over the range 0.5-20Hz with 4 male subjects (age ave21.5, SD0.5, weight ave75kg, SD7.91kg, height ave166.8cm, SD5.2cm) and 4 suspension seats. As Fig.2 shows, subjects evaluated the degree of discomfort every 5 seconds to each seat vibration measuring the seat z-axis vibration acceleration. [ ]

Jan 6, 2006

By Suresh K. Bhatt, Christopher Mark

Fatalities caused by highwall/spoil bank failure in the surface mines, coal and non-metal, increased to an alarming rate of seven during 1999. To determine the causes of slope failure and successful mining practices, the National Institute for Occupational Health and Safety undertook a study. The study included: 1.A review of accident statistics; 2.A review of Federal and state mining laws pertaining to surface mining; 3.A literature review, and; 4.Mine visits. The study emphasized surface mines in the states of West Virginia, Ohio, and Pennsylvania. The review of a decade’s accident statistics using the mine Safety and Health Administration’s (MSHA) database showed that approximately 40% of all ground control related incidents reported to MSHA occurred in just four eastern states: Kentucky, West Virginia, Pennsylvania, and Ohio. The comprehensive literature search provided a historical perspective of highwall stability issues. Eleven mines we visited to obtain data on their mining practice or design. Commodities included coal, sandstone, and limestone. Based on the visits, five case studies were developed to represent typical mining methods and effective ground control practices used in eastern surface mines. Benching was found to be a common technique to reduce the overall highwall slope angle. Decking in the softer zones, such as shale, proved useful in controlling damage due to blasting.

By Steven J. Page

Researchers have developed a model to describe airborne respirable dust (ARD) generation on surface coal mine drills. By measuring a few basic parameters and using a graph, a drill operator or engi­neer can estimate the relative severity of drill dust emissions as well as how much of a reduction in ARD can be obtained by changing any given parameter. Geometric parameters include: drill deck cross-sectional area, shroud leakage associated with the deck shroud as well as the operational parameters of bailing air­flow, and dust collector airflow. The rela­tionships yield predictive ARD values which fall in the range measured on oper­ating drills for collector/bailing air flow ratios greater than 2. Overexposure to airborne respirable crystalline silica dust can cause serious or fatal respiratory disease. Exposures of sur­face coal mine rock drillers to respirable crystalline silica are of particular concern. In a 1992 alert on silicosis in rock drillers, the National Institute for Occupational Safety and Health (NIOSH) reported on 23 cases of advanced silicosis (acute, acceler­ated, and chronic) ranging in ages from 25 to 60 with drilling tenures ranging between three and 20 years.1 Most of the cases involved drill operators in their 30?s and 40?s, indicating high silica exposure levels are associated with their occupation. A more recent lung x-ray surveillance study of a 664 volunteer population of surface coal miners showed that the prevalence of silicosis-like abnormalities was 9%.2 The two most significant factors associated with these abnormalities were increasing age and years of drilling experience.

Jan 1, 2008

By Paul M. Tyler

"In preparing this paper the writer has perforce depended mainly upon published information, including the catalogs and pamphlets issued by importers and dealers such as the Diamond Drill Carbon Co. and J. K. Smit & Zonen. Special acknowledgment is made to various articles published by S. H. Ball. The writer of this paper, however, is alone responsible for statements herein contained and since he has often found it necessary to rationalize apparently conflicting opinions of recognized authorities on this little-known subject, he will welcome constructive criticism from the trade.Two types of diamond are extensively used for industrial purposes. One type, known as bort or bortz (boort, boart, bowr, etc.), consists of diamonds of the gem variety but unfit for cutting into gems. They may be colorless, yellow, brown, or gray. The other type, carbonado, known in the trade as ""carbon"" or ""black diamond,"" differs greatly from the white diamond, being opaque and apparently amorphous or noncrystalline. Actually, instead of forming a large single crystal as in a gem stone, carbon diamond comprises a mass of microscopic crystals that interlock to form a tough, homogeneous material with no planes of cleavage. It is found in various colors -- black, dark green, brown, and gray -- but usually it has .a dark lustrous black surface, with a resinoid or submetallic appearance, often resembling fine-grained steel. Upon exposure to the air the broken surface gradually darkens to an ash-gray color. Ballas is a special type of carbonado in which the crystals are definitely-oriented around a central nucleus. They are harder and tougher than ordinary carbonado but are much scarcer. The Cape ballas is reputed to be not quite so tough as Brazilian ballas but tougher than carbon or bort.The diamond crystals are isometric and take a variety of forms. The cleavage is octahedral and well marked. A crack is easily -started parallel to an octahedral face, and bort or gem diamonds are notoriously brittle, especially when subjected to sudden shock. Even carbonado, while it has a high resistance to slowly applied pressures, may be chipped or broken by a sharp blow.Exposed to radioactive rays, the diamond becomes phosphorescent; this property is often utilized to distinguish it from quartz, topaz, or glass. The unusually high refractive index likewise aids in its identification in the case of a more or less transparent stone. At the temperature of the electric arc, diamond is converted into graphite, another form of Carbon but one of the softest mineral substances. At a much lower temperature, as low as 1,5620 F., the diamond may be burned like ordinary carbon in an atmosphere of oxygen, and according to some authorities there is danger of burning a diamond if overheated even in air."

Mar 1, 1932

By P. M. Gruzensky

A survey of the literature has been made covering the extraction of bismuth from raw materials, its separation from lead, and its subsequent refining. The use of aqueous, nonaqueous, and fused electrolytes in electrolytic refining is reviewed. This literature survey has been prepared preliminary to some proposed investigations concerning the electrometallurgy of bismuth, and, although an effort has been made to cover a majority of the applicable references, a critical review was not attempted and no assertion is made that this manuscript is exhaustive in nature. Titles of publications in parenthesis are translations from the language in which the reference was originally published.

Jan 1, 1954

By Edward W. Parsons

The transverse force developed by expansion-shell rock-bolt anchors on the wall of a drill hole as the bolt is tensioned was measured by the Bureau of Mines using a device specially designed and fabricated for attachment to a universal testing machine. Load cells equipped with electrical-resistance strain gages provided the data from which the transverse force, in pounds, was calculated. Seven different expansion-shell anchors were tested, and the ratio of transverse force to bolt-tension load was found to range between 0.98 and 1.94 to 1.0. The drag load appeared to be the major cause of the transverse-force variation, but the relative effects of individual factors that affected the ratio between the transverse force and the bolt tension were not determined.

Jan 1, 1968

By Dean H. Ambrose

This paper presents the results of a study using computer human modeling to examine machine appendage speed. The objective was to determine the impact of roof bolter machine appendage speed on the likelihood of the operator coming in contact with. A contact means two or more objects intersecting or touching each other, e.g., appendage makes contact with the operator?s hand, arm, head or leg. Incident investigation reports do not usually contain enough information to aid in studying this problem and laboratory experiments with human subjects are also not feasible because of safety and ethical issues. As an alternative, researchers developed a computer model approach as the primary means to gather data. By simulating an operator?s random behavior and machine?s appendage velocity, researchers can study potential hazards of tasks where it is not possible to perform experiments with human subjects. Analysis information is helpful to the mining industry in terms of making recommendations that reduce the likelihood that roof-bolter operators experience injury due to contact with a moving boom. Data analysis of roof bolter simulations show that the virtual-operator?s response time has little effect on the number of contacts experienced. Based on frequency and cross-tabulation, regardless of other variables, contact incidents were always greater when the boom was moving up, were always greater on the palm, and were always greater for the boom part of the machine. Also, regardless of boom speed, the 25th-percentile-sized operators experienced more contacts than did other operator sizes. Furthermore, regardless of boom speed, the 152-cm mine seam experienced more contacts than did other seam heights tested. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speed greater than 41 cm/s results in a substantial increase in risk to the roof bolter operator and should probably be avoided. At speeds less than or equal to 25 cm/s are associated with a more modest relative risk, which represents an acceptable level of risk. Also, at speeds between 25 and 41 cm/s, there could be a particular boom speed in this range at which a significant inflection point in the relative risk estimates occurs. Based on the results, this issue needs to be addressed by future research.

Jan 1, 2003

By Jeffrey M. Listak

The National Institute for Occupational Safety and Health (NIOSH) conducted field tests to evaluate the effectiveness of a wet head continuous mining machine for reducing dust exposure for continuous miner operators. Wet head technology delivers water via sprays to the continuous miner's cutter head as opposed to traditional standard sprays located on the boom and body of the mining machine. The sprays, positioned directly behind each bit on the cutter head, deliver water at the point of attack, serving to cool the bits during mining to reduce the potential for frictional ignitions. The sprays also flood the coal with water to potentially suppress dust generation. Dust surveys were conducted at several mines to evaluate the wet head's effectiveness to control respirable dust exposure at the continuous miner operator location and in the immediate return. Results show that the wet head miner improved air quality at both locations to varying degrees in some cases and not in others when compared to a continuous miner with a standard spray system.

Jan 1, 2010

By Michael E. Henderson

The U.S. Bureau of Mines (BOM) constructed the Hydraulic Transport Research Facility (HTRF) to investigate the hydraulic parameters relating to the transport of coarse coal. To achieve these goals in a timely and efficient manner, the Bureau contracted to Boeing Services International, Inc. (BSI) the responsibility of operating the HTRF and providing technical support. This data report is a summary of the testing and data results for the period from 16 September to 1 November 1983. The testing covered herein is for coarse 2-in by a (minus 50 mm) Pittsburgh Seam coal in a 12-in (3 00 mm) pipeline, at velocities ranging from 5 to 18 ft/s (1.5 to 5.5 m/s) and at concentrations ranging from 15 to 55 pct.

Jan 1, 1985

By W. J. Wenger

Colorado has been producing petroleum since 1863 but only recently has become a major oil State. The first well was drilled on Oil Creek near Florence, but out-put was relatively small until discovery and development of the Weber sandstone reservoir at Rangely. Oil was discovered in the Weber sandstone in 1933, and the reservoir was developed after 1940, bringing Colorado, in 1949, to 11th place among the 48 States as an oil producer. Colorado's output increased further because of the discovery and development of many fields in the Julesburg Basin since 1949 By 1954 Colorado was in ninth place and maintained that position through 1955.4/ Between 1946 and 1951, Colorado's oil production more than doubled, while the total United States production increased only 25 percent. It seems probable that production will continue to expand in Colorado for many years. This report presents analyses of 92 crude oils from 73 fields representing 90 percent of the production in 1955. Abridged analyses are listed for easy comparision, and complete analyses arc given in the appendix. Oil samples were collected for study from many different sources. Although many of the newer fields were not sampled, their oils probably are very similar to those from corresponding formations that were studied and tabulated.

Jan 1, 1957

During development mining, ventilation capacity may decrease and the ventilation requirements may depart from initially planned values depending on the mining rate, increases in the methane emission rate, and changes in ventilation airway leakages. Insufficient ventilation air quantities and the occurrences of high methane liberation rates can overwhelm the existing quantity of ventilation air and result in elevated levels of methane gas during development mining. This condition can both limit the development of that section and increase the risk for an ignition that may lead to an explosion. Thus, the prediction of ventilation air requirements prior to mining can enhance worker safety by reducing the likelihood that explosive methane-air mixtures form. This study presents an approach for prediction of methane inflow rates using coalbed methane reservoir modeling. For this purpose, a two-phase coalbed reservoir model of a three-entry type roadway is developed. In the model, grids are dynamically controlled to simulate development of entries. Examples are given for methane inflow and ventilation air requirements as a function of mining rate, development section length, mining height, and the existence of degasification boreholes. This technology can be used to limit the methane concentrations occurring as a result of the influences of various coalbed and operational parameters.

Jan 1, 2008

By J. Burlin Johnson

This report describes an investigation of the relationship between crater dimensions formed in laboratory blasting experiments and the mechanical properties of the material cratered. Scaled field data have been included when available. The results show that tensile strength and possibly other mechanical properties may be useful in predicting maximum crater dimensions.

Jan 1, 1963

By Paul Wellman

A computer program is presented that may be used to calculate the bare equipment cost of the major processing units for any hot potassium carbonate gas purification system. The program is designed such that, with only minor modifications, it could be used with a variety of computer systems.

Jan 1, 1968

The Bibliographic Data Base contained in the present volume is the result of a literature search conducted as one task of the Bureau of Mines project concerned with research in borehole assay technology. The data base includes articles, symposia, books, corporate and government reports, patents, and other literature concerned with some aspect of borehole logging, from January 1969 through December 1975. Occasional updating to keep the data base current is anticipated. The remainder of the intro¬duction will be devoted to the explanation of the organization of each entry, along with the translation of terms and abbreviations used in the text. Each entry contains six sections. These include an ID code, a title, an author section, a source section, an abstract, and a descriptor section. The first item listed in an entry is the ID code. This serves to identify an entry. It consists of the first six characters of the first author's (or editor if no authors are involved) last name, along with the last two digits of the year of publication. A letter sometimes follows the year of publication to assure a unique alphanumeric code. For example, if an author named Wilson writes more than one piece of literature in a given year (for example, 1972), the ID code for the entries identifying these pieces of literature would be identical. Therefore, to allow for unique ID codes, the first piece would he identified as "WILSON 72,', the second piece as "WILSON 72A", the third "WILSON 72B", and so on.

Jan 1, 1976

By Louis C. Brichta

The Rush Creek district of Marion County, Ark., has had a more or less continuous record of zinc production over the past 40 years. The ore has come from many small mines working on oxidized and semi-oxidized deposits found in the Everton formation where that formation forms the present surface rock. Prospecting has been restricted to the hillsides above the creek levels, the actual ore outcrops being the guides. Little attention has been paid the possible sulfide zones. In August 1942, the United States Geological Survey and the Bureau of Mines recommended exploration of the Powell and Cotter formations, which underlie the Everton, for which purpose the Survey had previously located 18 proposed drill-hole sites in geological structures that seemed favorable to are deposition.

Jan 1, 1949

By John E. Hamak

The U.S. Bureau of Mines estimates the identified helium resources of the United States at 630 Bcf as of December 31, 1990. This includes 295 Bcf of demonstrated reserves, 87 Bcf of demonstrated marginal reserves, and 42 Bcf of demonstrated subeconomic resources. The identified resources include 161 Bcf of helium in inferred and marginal reserves and 45 Bcf in inferred subeconomic resources. The identified helium resources contained on Federal lands are approximately 170 Bcf, including 32 Bcf in underground storage in the Cliffside Gasfield near Amarillo, TX. In addition to the identified helium resources, undiscovered helium resources in the United States are estimated at a most likely volume of 103 Bcf, with a maximum volume of 259 Bcf and a minimum volume of 41 Bcf. Also reported are 43 Bcf of helium in nonconventional and low-helium-content natural gases. Current extraction of helium in the United States occurs mostly from natural gases produced from the Hugoton gas area in Kansas, Oklahoma, and Texas, and the Riley Ridge area in southwest Wyoming. Helium extracted from natural gas in the United States in 1990 was 2.5 Bef. If current trends continue, some shortfalls in helium supply may occur in about 5 to 10 years.

Jan 1, 1993

By Jack D. Ramsdell

Electrorefined, magnesium-reduced, and sodium-reduced titanium samples were evaluated for recrystallization behavior, effect of cold rolling on tensile properties, and bend ductility. Curves were determined for the softening of 2.5 to 80 percent reduced cold-rolled metal that was annealed over a temperature range of 300° to 800° C. Upon annealing, coarsening of the grains was found to occur for reductions in thickness of less than 20 percent in titanium made by all three processes. The presence of metallic impurities greatly inhibits coarsening for reductions in thickness below 20 percent, but for reductions in excess of 20 percent grain size is essentially constant at each annealing temperature. The three grades of titanium did not harden excessively from cold rolling; both tensile and bend ductility were good for reduction in thickness up to 80 percent. Upon annealing, softening occurs between 400° and 600° C., and, based on microstructure and property studies, full annealing is accomplished after 30 minutes at 700° C. for the magnesium-reduced and electrorefined titanium and at 800° C. for the sodium-reduced titanium.

Jan 1, 1960

A system to continuously measure the concentration of radon in mine ventilating air has been developed and tested in a uranium mine. In use, the air/radon mixture to be monitored is pumped through filters into a scintillation cell where nuclear decay of the radon produces flashes of light. These are electronically counted, giving a quantitative measure of the radon present. Air is continuously drawn from the mine atmosphere into the radon sensor box. This air sample passes through two filters into the detector cell as shown in the schematic diagram. A portion of the radon in the detector cell will experience nuclear decay, producing polomium 218 and an alpha particle. The alpha particles from the fraction that decays strike a zinc-sulfide coating on the inside wall of the cell and produce flashes of light. These enter a photo-multiplier tube which records each flash as an electrical pulse. An amplifier increases the voltage of each pulse, allowing electronic screening to remove noise and other undesirable pulses. The remaining pulses are counted by a conventional data acquisition system.

Jan 1, 1978

By Michael J. Sapko, Gregory M. Green, Kenneth L. Cashdollar

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted a joint survey to determine the range of coal particle sizes found in dust samples collected from intake airways of US coal mines. The last comprehensive survey of this type was performed in the 1920s. The size of the coal dust is relevant to the amount of rock dust required to inert the coal dust, with more rock dust needed to inert finer sizes of coal dust. Dust samples were collected by MSHA inspectors from several mines in each of MSHA's 10 bituminous Coal Mine Safety and Health Districts. Samples were normally collected in several intakes at each mine. The laboratory analysis procedures included acid leaching of the sample to remove the limestone rock dust, sonic sieving to determine the dust size, and low-temperature ashing of the sieved fractions to correct for any remaining incombustible matter. The results indicate that particle sizes of mine coal dust in intake airways are finer than those measured in the 1920s. This finer size coal dust in intake airways would require more incombustible matter to be effectively inerted than the 65% incombustible specified in current regulations.