Search Documents

By David A. Lipton

In 1983, U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources in the Carrizo Gorge Wilderness Study Area (WSA). The 14,571-acre WSA, located 42 miles east of El Centro, CA, is underlain primarily by Mesozoic granitic rocks and pre-Cretaceous metasedimentary rocks. Six prospects were found within the WSA and two mines are adjacent to it. Mineral deposits within the WSA have had insufficient development and rock exposures for calculating resources. The WSA contains no identified mineral resources; however, further exploration may disclose gem quality minerals. Two mines adjacent to the WSA, the Pack Rat and Beebe Hole, have produced gem quality kunzite and aquamarine from pegmatite dikes. According to the owners, a significant amount of gem minerals have been mined here in the last decade. Based on past production and the characteristic minerals indicating gem-bearing pockets, additional pockets are likely. Similar pegmatite dikes occur from Mt. Tule to Carrizo Gorge and may contain gem-bearing pockets. Pegmatite dikes also occur in the WSA near Rockhouse Canyon, but contained few of the mineral associations indicative of gem-bearing pockets. Manganese occurrences north of the Beebe Hole and Packrat Mines and within the WSA contain low concentrations of manganese. Significant sand and gravel were not identified. There is no evidence of deposits of oil and gas, or geothermal energy.

Jan 1, 1985

By Richard C. Moore

The U.S. Bureau of Mines contracted a study to review the air and water monitoring requirements of five Federal environmental acts (the Federal Water Pollution Control Act, the Safe Drinking Water Act, the Clean Air Act, the Surface Mining Control and Reclamation Act, and the Resource Conservation and Recovery Act) and to compile information on the currently available monitoring instruments. A literature review of the acts and their associated regulations was conducted to determine applicability to the mining industry as well as any air and water monitoring requirements. In addition, an industry search and literature review was performed to assess the instrumentation available to comply with the monitoring regulations. Based on this research, the instruments are classified by general applicability to air, surface water, or ground water monitoring, then catalogued by monitoring parameters. A discussion is provided on recommended and innovative monitoring techniques.

Jan 1, 1981

By J. S. Berber

Bastnasite is a natural fluocarbonate of the cerium group and affords an abundant and high-grade source of the lighter rare-earth elements. As part of a broad research program in rare-earth element technology, the Federal Bureau of Mines directed extensive experimental work to separating and purifying the rare-earth elements in bastnasite. By the use of a combination of techniques--classical chemical, ion exchange, and solvent extraction--the processing of a bastnasite concentrate to obtain the individual rare-earth elements, or groups of elements, was accomplished. A bastnasite concentrate, containing about 60 percent rare-earth oxides, was sulfated with concentrated sulfuric acid to eliminate the carbon dioxide, fluorine, and silica. Calcination at 1,200° F. made the gangue matter insoluble, thus permitting the separation of the soluble rare-earth sulfates. Essentially 100 percent of the rare-earth elements were recovered by this procedure. Since the rare-earth sulfate solution contained only trace amounts of nonrare-earth elements, subsequent separation procedures were simplified.

Jan 1, 1960

By John C. Edwards, Gene F. Friel

A series of liquid fuel fire experiments evaluated the comparative responses of five types of commercially available smoke detectors and a diffusion-mode carbon monoxide (CO) detector under normal and reduced airflow conditions based upon the alarm times of the detectors. These experiments were conducted in the Safety Research Coal Mine at the U.S. Bureau of Mines Pittsburgh Research Center. Two of the smoke detectors had manufacturer set alarms. For the other three smoke detectors, an alarm point was defined in terms of their background analog signal and the detector's electrical output noise under ambient conditions. A correlation was developed of the travel time of 5 ppm CO between pairs of CO detectors with the travel time calculated from entry and crosscut volumes and measured airflow. Based upon the relative performance of smoke detectors in this limited study, smoke detectors can be as effective as CO detectors for mine fire detection once identifiable alarm values are defined. Implementation of smoke detectors as part of an atmospheric mine monitoring system will improve mine safety.

Jan 1, 1996

Reduce respirable dust exposure of workmen operating auger-type continuous mining machines. Approach: An auger miner was fitted with an exhaust system which draws dust laden air through a [scruber] and discharges it behind the line curtain. How It Works: Dusty air is drawn into the space above the coal conveyor and through a scrubber, by two fans mounted side by side above the conveyor. Exhaust from the fans passes through a duct to the side of the auger miner, and into tubing that runs back and into the air return passage formed by the line curtain. See Figure 1. Of the 5,000 cubic feet per minute of air normally entering the working place, 4/5 is drawn out through the dust exhaust system. The system was installed on a Wilcox Mark 20 Miner and tested underground by personnel of the Bureau's Pittsburgh, Pa., Mining and Safety Research Center, under a cost sharing

Jan 1, 1976

By J. W. Paul

A study of mining methods and underground practices as they influence injury from falls of roof or coal reveals data as to the location in the mine where such injuries occur with the greatest frequency and as to some of the methods and practices which are in use for the prevention of injury. This paper, which presents statistics bearing on the frequency and place of occurrence of accidents and discusses regulations and practices which have resulted in a low-frequency rates from falls of roof and coal in a few representative mines, takes its information from mine-accident reports and from the results of studies conducted in a group of 80 mines in the bituminous coal fields of Western Pennsylvania, Ohio, and West Virginia. The statistics from this group of mines cover periods of one to four years but average 2 years and 7 months. During this time these mines produced over 110,400,000 tons of coal, equivalent to one-fifth of the annual production of all bituminous mines in the United States. The coal beds of the mines in the group studied are mostly flat, with local pitches of moderate degree. A number of mining plans are in use, each of which follows a general system of multiple entries, gross entries, and rooms. Room and pillar in panels either advancing, retreating, or half advance and half retreat, and the block system are employed. The methods of pillar extraction are by splitting, slabbing, pocket-and-stump, and open end. It is hoped that in presenting some of the details of the methods and practices at particular mines of this group which have commendable records in the prevention of injury some goad may accrue to many other bituminous mines which have similar natural conditions.

Jan 1, 1933

By O. C. Blade

This report on the properties of burner-fuel oils produced during 1956 was issued under a cooperative agreement between the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, at the request of the Oil-Heat Institute of America and the petroleum industry. This survey is the second for this type of fuel, the first being made in 1955. 2/ The surveys are conducted to provide information on the characteristics of burner-fuel oils now manufactured for sale. They are similar in pattern to the diesel-fuel surveys, conducted since 1950, 3/ and are not intended to conflict with but rather to supplement them. The importance of fuel oil has resulted in the need for more information by the petroleum industry, manufacturers of heating appliances, and consumers regarding the types and qualities of the fuels currently being marketed. Samples of burner-fuel oil typical of their manufacture during the early part of 1956 were analyzed by the refiners in accordance with instructions from the subcommittee on fuel surveys of the Automotive Research Committee of the American Petroleum Institute, Results of the analyses were transmitted to the Bureau of Mines where the data were studied and compiled as shown in the tables of this report.

Jan 1, 1956

By K. L. Erickson, Gerald A. Munson

"The need for spodumene as a source of lithia for war purposes led to the exploitation of the Edison pegmatite deposit 1-1/2 miles southeast of Keystone, S. Dak. The operation was conducted during 1943 and 1944 by the Lor Mining Co., Rapid City, S. Dak. Spodumene concentrates in the ratio of 15:1 were recovered by hand picking from a sorting belt. This method was expensive and wasteful of spodumene, owing to the small size of the crystals.Data4/ obtained by the Bureau of Mines indicates that blunging with hydroflouric acid or sodium hydroxide is a prerequisite to selective flotation. Results of tests by Denver Equipment Co., Denver, Colo., indicate that economic recoveries can be obtained in an alkaline circuit after desliming.At the request of the Lor Mining Co., K. L. Erickson, metallurgical engineer, was permitted to work in the pegmatite research laboratory to verify previous investigations and to determine problems that might be involved in commercial milling. The ensuing investigation indicated that electrolytes in the mill water produced a profound inhibiting action on the flotation of Edison spodumone.An investigation of mill water from various sources showed that some waters are suitable for the process and others are not. Subsequent testing showed that all of the available waters are suitable after treatment. The flotation of the Edison spodumene in an alkaline circuit after desliming and using oleic acid as collector is efficient and economical when the water does not contain impurities.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B.Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches arc under the supervision of Dr. R. S. Dean, assistant director.As the work was of a practical nature, samples from possible mill-water sources in the southern Black Hills were obtained, and commercial softening and demineralizing methods were investigated. Data on various waters tested are given in table 1."

Jun 1, 1946

By Peter F. Steidl

Seven degasification wells have been completed in the Pittsburgh coalbed at the new Emerald mine near Waynesburg, Pa. Funding was provided by the Bureau of Mines to perform stimulation treatments on five of the wells, to show that this is a feasible and economical means of degasifying part of a coalbed. The seven wells ranged in depth from 590 to 910 feet. Stimulation treatments used 25,260 to 42,660 gallons of foam and 7,400 to 12,800 pounds of 20/40-mesh prop sand. Pumping rates were 10.8 to 11.6 bbl/min and treating pressures were from 1,050 to 1,600 psig. On the day following stimulation, gas production ranged from a few hundred cubic feet per day to more than 100,000 cu ft/day.

Jan 1, 1978

By Raymond B. Ladoo

"The name bentonite has been applied to a group or series of clay-like materials characterized by an alkaline oxide and alkaline earth content of 5 to 10 per cent, fine grain Giza, high absorptive powers, and usually very strong colloidal properties.Bentonite probably represents no mineral of fixed composition, and its physical properties vary considerably. The type material from Wyoming is light yellow or greenish yellow in color, but from other localities it may be cream colored, white, gray, pink, dark brown or even black. It is exceedingly fine grained, very plastic and highly absorbent. The appearance may be dull or powdeay, but a freshly cut surface usually has a waxy luster. Some varieties have the appearance of wax and may be cut into very thin, translucent shavings. The fracture of the type material is roughly conchoidal, that of other varieties is platey and shale-like, while still others have no typical fracture. Bentonite is highly absorbent; .hen wetted it will absorb more than three times its weight or seven times its volume of water. Some varieties when wetted with water expand to more than six times (some experimenters report eight times) their original volume. The wetted material is exceedingly smooth and soft and feels like soft soap. Unlike most clays, bentonite is easily fusible at a comparatively low temperature.Under a high-power microscope bentonite seems to consist of extremely small, more or less rounded, grains of uniform size, but the texture of most varieties is so fine that individual grains can not be distinguished.Some varieties when finely ground and thoroughly agitated with water will stay in suspension indefinitely, forming a translucent gelatinous mass. The addition of small amounts of acids or sodium chloride seems to have little or no tendency to raid coagulation or settling. Other varieties of similar analysis and appearance go into suspension more easily, but settle out again in a comparatively short time. It has been suggested that the material which stays in suspension indefinitely is a true colloid of the emulsion or lyophilic type."

Oct 1, 1921

By Harvey Patashnick

Current state-of-the-art microweighing technology represented by the Tapered Element Oscillating Microbalance (TEOM) is utilized as the basis for a new generation of Personal Dust Exposure Monitors (PDEM's). Two design configurations are presented. The first is an end-of-shift analysis system which uses small TEOM-PDEM cannisters that replace the filter cartridges in the current PDEM system. All other components carried by the miner (cyclone preseparator and pump) are the same. After the shift the TEOM cannister is plugged into an interface box which enables a minicomputer to automatically identify the unit, determine the dust mass increase during the shift, compute the shift average dust mass concentration, and print out and/or store the data. The second design is a real-time TEOM-PDEM system which is capable of operation over a 10-hour shift and on demand display real-time dust concentration level, time weighted average, and shift average concentration. As a result of the design study, a prototype end-of-shift analysis system was fabricated and delivered to the Bureau of Mines. A description of this system which consists of six TEOM cannisters, interface electronics and minicomputer is given. The system represents a significant advance in the dust monitoring program in terms or accuracy and automation.

Jan 1, 1983

By Robert E. Manning

At present, a need exists for more effective noise control in the coal-mining industry. In particular, new muffler designs with the required acoustic performance are needed for percussive pneumatic drills. Accordingly, the U. S. Bureau of Mines issued a contract to USS Engineers and Consultants to design a muffler capable of attenuating the noise from the air exhaust of a pneumatic drill. The specific objective of the contract was to design and deliver a prototype muffler that would attenuate the air-exhaust noise to 90 decibels on the A scale (90 dbA). The test drill used in this investigation was one used for roof-bolting purposes in coal mines. Using the combined approach of analysis by digital-computer program and experiment by simulated-noise tests, three prototype mufflers were designed and constructed at U. S. Steel Research. The mufflers consisted of a variety of resonator chambers and expansion-contraction chambers, and were of the following sizes: A muffler with a 3- by 5-inch elliptical cross section and about 8 inches in length. A muffler 5 inches in diameter and about 5-1/2 inches in length. A muffler 5 inches in diameter and about 10-1/2 inches in length. These mufflers were subjected to laboratory tests to determine their effectiveness in attenuating exhaust noise, mechanical noise, total drill noise, and simulated noise. All mufflers reduced the exhaust-noise level by about 25 dbA - from about 115 dbA without a muffler to below 90 dbA with a muffler - and thus were successful in meeting the contract objective. Field tests were conducted with the three prototype mufflers at U. S. Steel's Robena No. 4 Mine, and no icing problem was encountered. A fourth prototype muffler was designed to fit around the leg of the pneumatic drill. Tests showed that this kidney-shaped muffler also reduced the air-exhaust noise to below 90 dbA.

Jan 1, 1973

By Len Blackman

The Absaroka-Beartooth Study Area is a tract of approximately 1.4 million acres of National forest land in southern Montana, part of the Greater Yellowstone Area. This study evaluated the mineral potential of four mineral terranes containing undiscovered resources in the area. The geological data is probabilistic, with estimates of the possible number: of deposits and their grades and tonnages. Possible future development scenarios range from no development to many mines, including some very large. As two thirds of the study area is within the Absaroka-Beartooth Wilderness, the future development scenarios reflect the area's mineral potential, not what we expect to see in the foreseeable future. Based on the analysis performed on these four terranes, the most likely future scenario for the study area would include the potential for two medium sized, (predominately) gold, mines, each employing a few hundred workers. There is a small chance, less than 5%, that a large Porphyry Copper or Superior Iron deposit would be discovered and be economically feasible to develop.

Jan 1, 1994

By R. C. Butman

The Lincoln Terminal System (LTS) is a stand-alone computerized training device that presents high quality visual displays, and audio messages to a student. A keyboard is provided for student input. A variety of student-machine interactive programs arc provided. These programs allow the author/instructor to evaluate numerical entries and responses to simple and compound multiple-choice questions (where a compound choice is defined to be more than one choice, ordered or unordered from one or more list(s) of choices. Descriptions of LTS applications, lesson development procedures, hardware provided and support facilities required are given. A contract history summary, and a bibliography of reports published under three successive BoM contracts supporting LTS development, is provided.

Jan 1, 1979

By Corwin L. Cooper

This paper, describing; the milling and cyanidation methods and costs at the Yellow Aster gold mine, is one of a series of papers being prepared by the Bureau of Mines on bold milling practices in the United States. Acknowledgments Acknowledgment is made to the executives of the Anglo American Mining Corporation, Ltd., for permission to publish this article, and to A. W. Frolli, manager, and other members of the company staff, for assistance` in preparing the, paper.

Jan 1, 1936

By Sean Gallagher, Gene Wilson, Christopher Mark, Craig S. Compton, Gregory M. Molinda

Falls of small pieces of rock from between roof bolts continue to cause fatalities and to injure hundreds of coal miners each year. Roof screen is the most effective way to prevent these incidents, but some mines are reluctant to use it because they believe installing screen can be awkward, expensive and time-consuming. The most common type of roof bolting machine used in mines today is the dual boom, outside-controlled roof bolter. Mines who install roof screen using these machines have developed some machine modifications and techniques to ease roof screen installation. This paper describes some successful techniques and machine modifications that are being used in productive mines to assist with roof screen installation. Since the material handling involved with roof screen installation can expose miners to an increased risk of musculoskeletal injuries, the National Institute for Occupational Safety and Health (NIOSH) ergonomists, designed machine modifications and implemented a series of tests to evaluate roof screen handling procedures for outside-controlled, dual boom roof bolting machines. Roof screen installation can also have a positive economic impact on a mine by reducing the cost of injuries, workers’ compensation, required spot or re-bolting, and clean-up of long term travel and belt entries.

Reduce the danger to personnel and destruction of equipment caused by fires on surface coal augers. Approach: A reasonably priced reliable system which automatically senses a fire and activates dry chemical extinguishers, has been built and field tested. How It Works: Heat sensors mounted in the engine compartment and hydraulic hose areas detect the fire, usually before the operator does. This causes the system to automatically discharge A-B-C class dry chemical extinguisher through a fixed piping system.

Jan 1, 1976

By Michael R. Kennedy

This report describes the demonstration of longwall mining in a seam dipping 27 to 34'. Equipment was selected on the basis of capability, compatibility, and co t. Snowmass, Bureau of Mines, consultants and manufacturers were involved in the selection process. The equipment arrived in early 1981, prior to completion of development for the first panel; therefore, the equipment was operated on the surface for training. The surface training paid off with a fast, efficient installation and start-up of the face. The longwall equipment operated very well on the steep pitch with an average equipment downtime of 21.9[9]. Coal handling outby the face was a problem which caused an additional downtime of 19.5%. Development for the panels proved to be the major problem in the economics of longwall mining on a steeply dipping seam. During the first 9 months of operation the longwall averaged 71.9 TPMS and development averaged 0.6 TPMS for an overall average of 14.1 TPMS. Had mining continued, timing of development would have been another major problem. Monitoring of subsidence, pillar stability and shield loading was done in connection with mining, but little useful information was gained from the monitoring.

Jan 1, 1987

Table A-1. Number of underground coal mines and samples collected for underground occupations, 1988-92 [ ]

Jan 1, 1997

By Scott W. Hazen

METHODS of determining the grade and tonnage in a mineral deposit have not kept pace with scientific developments in certain other fields. The most commonly used methods of computing ore reserves and grade based on diamond-core-drill sampling are the cross section, the polygon, and the triangle. Tonnage and grade may be determined by these methods with acceptable accuracy, providing a sufficient number of samples is obtained; however, there is no means of determining when an adequate number has been taken or conversely if the deposit has been sampled excessively. It is demonstrated that, by using the techniques of statistical analysis, a mining engineer will be able to determine when a sufficient number of samples has been taken to determine the grade of a mineral deposit within a specified degree of confidence. Using statistical analysis to compute the estimated average grade of the ore makes it possible to compute a fiducial interval, when a distribution of the sample means is normally distributed, so that there is 95-percent confidence in the statement that the true average grade of the deposit is covered by the interval. This report utilizes data obtained from the Maggie Canyon manganese deposit, Artillery Mountains region, Mohave County, Ariz. Four separate exploration projects were conducted at Maggie Canyon between 1936 and 1950. Present economic conditions have made it desirable to determine the amount of 5-percent manganese ore developed by these projects.

Jan 1, 1957