Search Documents

By S. P. Cashin, D. Kashuba, W. Esplin

Barrick has had 6 autoclaves in operation at the Goldstrike Mine, North of Carlin Nevada, since 1993. The 6 autoclaves operate in parallel, processing slurry of gold ore. The gold in the ore is predominantly associated with, and encapsulated by, sulphide minerals. It is necessary to oxidize at least 90% of the sulphide mineral before the gold can be concentrated using a cyanide/carbon-in-leach (CIL) circuit. Sulphide oxidation chemical reactions occurring in the autoclaves are exothermic; however, the sulphide content in the ore is not high enough to operate the autoclaves in an auto-thermal mode. Heat from steam is added to the first 2 of 5 autoclave compartments to initiate the sulphide oxidation reactions. The steam used to heat the autoclaves is supplied by three boilers, which are fuelled with propane gas. The completion of a few operations and maintenance projects in the last 2 years has resulted in a 50% reduction in propane energy requirements. The autoclave operating temperatures were minimized. Excess oxygen addition was held as low as possible. The material of construction for the compartment walls inside the autoclaves was changed from brick to Titanium metal. And, the speed of the autoclave slurry agitators was increased. All of these activities had an impact on the propane energy requirements of the autoclaves. Presented below is a description of the autoclave systems, and a discussion of how the energy needs were reduced, resulting in significant operating cost savings.

Jan 1, 2004

By R. M. Beauchamp

Base metal processing operations often treat process tailings and acid mine drainage using a high density sludge (HDS) water treatment process. Lime is used in this process, which reacts with existing sulfates to form gypsum. When a recycle stream is incorporated in the process, gypsum levels in recirculating water may build up and cause high levels of gypsum supersaturation. Precipitation of gypsum from the supersaturated process water causes many problems. It is speculated that gypsum may precipitate on sulfide minerals and silica gangues in the flotation circuit, resulting in decreased selectivity and recovery. An understanding of the determinants and nature of precipitation may provide solutions to mitigate the formation of precipitates and improve flotation performance. This study showed that both sphalerite and silica exhibited gypsum- or calcium carbonate-like behavior in the respective supersaturated solutions, indicative of a coating of calcium species on the mineral particle surfaces. The addition of copper sulfate and/or potassium xanthate had little effect on the precipitation of gypsum or calcium carbonate on the mineral particles. Sodium carbonate is encouraging as a method to minimize calcium species interactions on sphalerite/silica surfaces.

Jan 1, 2006

By R. H. Wallis

Weighted moving-average contour maps have been constructed for molybdenum, copper and zinc using 7850 stream-sediment samples from 5430 square miles (14,063 sq. kms) of south-central British Columbia. Regional trends for molybdenum and zinc are northeast, north and northwest and those for copper are north and northwest. These trends are interrupted by zones markedly low in metals . The metal-rich trends cross rocks of different lithology and age and thus appear to be structurally controlled. The northeast trend may have exerted control on metal distribution at two different times.

Jan 1, 1978

By Eugene Sun, Qiang Xu

This presentation will review current applications of composite materials in aircraft design and discuss the challenges involved in maximizing the potential of the composites in aircraft applications.

Jan 1, 2010

By Ernest Becker

Golder Associates provided overall radiological direction and assistance to the client in their interactions with the Canadian Nuclear Safety Commission and operational radiation protection services for the remediation of a calciner that had been used to process uranium. The project was somewhat unusual in that the radioactivity from within the calciner room was removed from the site and the cleaned steel recycled. The presence of yellowcake within the process equipment required stringent radiation protection measures. This project was completed successfully with minimal radiation exposures to the workers and the effective protection of the environment.

Aug 1, 2010

By A. Sadough vanini A. Kami

In this paper, effects of different ageing treatments on the mechanical properties, microstructure and formability of 7075 aluminum alloy have been studied. Forming limit diagrams of the alloy have been obtained for four ageing conditions including T6, OA1, OA2 and O. For this purpose, combination of uniaxial tensile tests and the Erichsen cupping tests with different sizes and shapes of sheet specimens have been performed after each ageing treatment. The highest formability and the lowest formability have been observed at samples with O and T6 ageing treatments, respectively. Also, investigation of precipitated microstructures showed that the size of precipitation particles has a significant effect on the formability of the alloy. Formability improves with coarsening of precipitation particles.

Oct 1, 2011

By K. Nagy

To support the implementation of its integrated SHEQ Policy, Cameco has undertaken an environmental leadership initiative with the goal of moving beyond regulatory compliance and significantly reducing environmental impacts in five key areas: air emissions, treated water quality and quantity, energy use and greenhouse gas emissions, and waste generation. To ensure environmental leadership becomes routine business practice, it was necessary to integrate the initiative into Cameco?s programs and management systems at the corporate and operational levels. Operations based environmental leadership strategies and action plans have since been developed, as well as a corporate reporting system to monitor Cameco?s environmental performance.

Aug 1, 2010

"In 2008, the Committee for Mineral Reserves and International Reporting Standards (CRIRSCO) and the Russian State Commission on Mineral Reserves (GKZ) entered into an agreement leading towards harmonization of Russian and international minerals reporting systems. The purpose of the protocol is to define an agreed method by which mineral resources and reserves, reported by companies in Russia according to the current Russian classification system, can be expressed in terms that are comparable to the CRIRSCO reporting codes in Russia and elsewhere."

Jan 1, 2003

By P. M. Chapman

Risks to aquatic receiving environments from uranium mining and milling fall into three categories: physical (habitat change), chemical (e.g., uranium, selenium, total dissolved solids [TDS], metals including vanadium), and radiological. Although all categories of risk need to be managed, chemical risks are the most significant and are typically chronic rather than acute. For instance, selenium toxicity is primarily manifested as reproductive impairment due to maternal transfer, resulting in embryotoxicity and teratogenicity in egg-laying vertebrates. Risk is best assessed using a weight of evidence approach focused on ecosystem services. Risk management should be based on both risk assessment and adaptive monitoring.

Aug 1, 2010

By Theophile Yameogo

Much has been said about the methodology of geomechanical design in underground excavations. However, the geological, hydrogeological and geotechnical complexities encountered at the production horizons in the Athabasca Basin commanded for a novel approach in the geomechanical assessment and design of underground openings. Rock mechanics engineers at Cameco McArthur River have been able to establish a practical methodology that goes beyond known conceptual approaches. In this paper, the author describes the original challenges and unique approach in the geomechanical assessment for drifts and chambers development. The example of the successful development of the 510-8225N Chamber will also be presented.

Aug 1, 2010

By Ward G. Wilson

Best practice in the design and construction of soil cover systems for mine waste management has advanced extensively over the past two decades. While significant progress has been achieved, we still have little experience with respect to proven performance for cover systems that must last hundreds of years. Some cover designs appear to be functioning well, while at the same time the performance of many more are now being called into question. This presentation evaluates the integrity of cover systems from both a global and local perspective in relation to the uranium industry within Canada.

Aug 1, 2010

By M. Oliazadeh

The bioleaching of fine low grade copper sulfide ore is described. A sample of ground (> 1 mm) copper ore from Sarcheshmeh, Iran, was subjected to a series of agglomeration procedures and subsequently leached. The best agglomerate was obtained by using lime and sulfuric acid as binders. A column bioleaching test of agglomerated ore was then run for 105 days along with a non-inoculated control column having thymol as bactericide. The results show that about 77.5% of copper was extracted in the bioleaching, whereas the control column achieved only 57% copper leaching.

Jan 1, 2007

By J. Kang

There is increasing demand to utilize aluminium alloy sheets and their spot welds by the automotive industry. While traditional uniaxial tensile tests only determine mechanical properties to small strain, direct measurement of the constitutive behaviour of aluminium alloy spot welds at large strain remains a challenge. A technique was successfully developed using digital image correlation coupled with shear tests to directly measure the constitutive behaviour of an AA6022-T4 spot weld to large strains. The results show that the spot welding process not only decreases the yield strength but also lowers the work hardening rate of the nugget versus the base material. Details of sample preparation, experimental approach and results will be discussed.

Jan 1, 2011

By John Battista

Uranium mining in Australia has a chequered history. This paper reviews the development of the Australian uranium mining industry from the 1930?s to the present day. It outlines the geology of the various deposits and the mining and metallurgical techniques used to extract the uranium. The industry is profoundly affected by government policies and the paper considers the roles of the Federal, State and local governments. The influence of public opinion on nuclear issues and the effects current and historical policies of various governments have had on uranium mining are outlined. Despite heavy restrictions placed on it, Australia?s uranium mining industry has maintained its place as one of the world?s largest producers. This paper also provides an outline of where the industry in Australia may be headed in future.

Aug 1, 2010

By Sergio Bustos

A significant expansion project is under way at KATCO?s Torkuduk In Situ Leaching (ISL) operation to increase uranium production up to about 4000 tU/year. Higher flows and lower uranium concentration are expected in the rich solutions coming from the well fields. Therefore, extra adsorption and elution columns and modified operating conditions are required to deal with the increased demand for uranium transfer from the ISL solutions to the eluate solution, which goes to the uranium precipitation section. Resin adsorption and elution performance have been interpreted and projected by using Mac Cabe-Thiele equilibrium diagrams. The resin load, the adsorption mass transfer coefficient, the adsorption zone height and the eluate concentration have been estimated for the expected changing operating conditions associated to the future mine plan. This information has allowed to improve the present operation results and to define the main process design criteria for the expansion project.

Aug 1, 2010

By C. L. Belyk

There are fifteen accepted types of uranium ore deposits and at least forty subtypes readily identified around the world. Each deposit type has a unique geological model which may also have unique processing implications. Primary uranium production in the past decade has come from a handful of these deposit types: unconformity, sandstone, calcrete, intrusive, breccia complex and volcanic. Processing implications for each of the fifteen deposit types can vary widely between and within different geological models. Some key characteristics of uranium deposits that may have processing implications include: ore grade, uranium and gangue mineralogy ? including clay and carbonate species and content, hardness, porosity, uranium mineral morphology, and carbon content. Processing roadblocks may occur as a result of one or more of these characteristics for any of the fifteen deposit types. Future technological advances and innovative thinking around uranium ore processing could provide avenues for roadblock removal setting the stage for additional and economically-viable uranium production from traditional and non-traditional uranium ore deposits.

Aug 1, 2010

By Kimberly Morrison

Strategically located within the Uravan Mineral Belt District of western Colorado, the Piñon Ridge Project is the first new uranium mill being proposed for construction in the United States in over 25 years. In 1992, dramatic changes to the US regulatory environment for uranium ore processing occurred making regulatory compliance an increased challenge for a new facility. Proposed as a 6.3 million tonne uranium milling operation, the mill will receive ore from a number of mines in the region. The project includes design and permitting of a uranium/vanadium processing facility, tailings cells, evaporation ponds, and ore stockpile pads. The focus of this paper is to provide an overview of the US regulations and how these regulations were applied to design of the mill facilities, as well as provide a status update on the project as the mill license application was submitted to the Colorado Department of Public Health and Environment (CDPHE) in November 2009.

Aug 1, 2010

By D. Fredlund

The decommissioning of uranium tailings facilities often requires the design of a suitable cover system. In northern climatic environments there is a portion each year that can be considered to be ?inactive? while the remainder of the year can be considered to be ?active?. There are numerous engineering design assumptions required when analyzing both the ?active? and the ?inactive? portions of the year. Cover systems are subjected to complex boundary conditions and nonlinear unsaturated soil properties. The proposed paper describes the steps necessary for the preparation and the analysis of a multi-year climatic database for the design of a cover system in northern environments. The paper also explains how climate can be classified and how observed variations from one year to the next can be taken into consideration in cover design. The results of climatic records at two different sites are used to illustrate conditions that need to be taken into consideration when designing soil cover systems.

Aug 1, 2010

By Z. Manafi

Bioleaching of a copper sulfide ore containing "activated pyrite", using a mixed culture of mesophilic bacteria, was studied. This type of copper ore had been found unsuitable for flotation because it produces a concentrate containing relatively high iron concentrations and, therefore, a low copper grade. Microscopic observations showed that pyrite particles had been activated by the formation of a thin film of chalcocite. Hence, a bioleaching process was considered as an alternative to treat this ore. Following shake flask and acid consumption tests, column tests of the crushed ore (75% -12.5 mm) were initiated and the effects of culture medium, agglomeration, and irrigation type on copper recovery were studied. The results showed that all the columns containing bacteria had copper recoveries around 90% compared to the abiotic control column with a recovery of 50%. It was concluded that bioleaching could be successfully utilized to process copper ores containing activated pyrite.

Jan 1, 2007

By K. Waters, A. Navarra, T. Grammatikopoulos

Strategic decisions to develop a mineral deposit are subject to geological uncertainty, due to the sparsity of drill core samples. The selection of metallurgical equipment is especially critical, since it restricts the processing options that are available to different ore blocks, even as the nature of the deposit is still highly uncertain. Current approaches for long-term mine planning are successful at addressing geological uncertainty, but do not adequately represent alternate modes of operation for the mineral processing plant, nor do they provide sufficient guidance for developing processing options. Nonetheless, recent developments in stochastic optimization and computer data structures have resulted in a framework that can integrate operational modes into strategic mine planning algorithms. A logical next step is to incorporate geometallurgical models that relate mineralogical features to plant performance, as described in this paper.

Jan 1, 2017