Search Documents

By M. Kreuh

An investigation of the pressure pulse spectrum generated by the gas dispersion processes in a Peirce Smith copper converter was undertaken via the simultaneous measurement of four tuyeres using high frequency pressure transducers. The data was captured, stored, and analyzed using digital data processing techniques; including power spectral density plots, band-pass filtering, and a principal component analysis (PCA). The process was characterized throughout by a dominant 3 Hz pulse signature attributed to the formation of lateral gas envelopes. In particular, test tuyeres in the tuyere line tended to operate synchronously at the dominant frequency, regardless of operating conditions tested and despite being distributed along the converter. Synchronous behavior is thought to arise from the acoustic coupling and possible resonance behavior of the gas delivery system on the converter.

Jan 1, 2007

By A. D. Walters

"IntroductionScreens are used in coal preparation plants for four basic functions, namely:I. Scalping off large size run-of-mine coal for initial size reduction;2. Sizing of coal treatment in different process streams;3. Removal of magnetite (dense medium) from clean coal and refuse;4. Dewatering.Canadian coal preparation plants use screens extensively in the above functions. Even plants where no beneficiation takes place, screening and crushing are carried out in the size reduction process.Description of Process UnitsThe type of screen used in coal preparation plants generally falls into the following categories:Fixed Screens and Grizzlies (for large coal)Often a simple rugged construction, either set horizontally above a bin or inclined with the coal flow.Fixed Sieves (for fine coal)They are used for dewatering and/ or size separation of slurried coal or discard. The sieve bend, the Vor-Siv, the Wilmot riffle and the cross flow screen fall into this category. The most commonly used in coal preparation plants is the sieve bend, Figure 1. Coal slurry is fed tangentially onto a fixed curve wedge wire screen deck. The solids are separated at a predetermined particle size, delivering a partially dewatered overproduct and a dilute underflow. The coal slurry is initially delivered to the sieve bend via a feed box. A series of baffles spreads the feed evenly across the width of the deck. The slurry drops from the last baffle, passes through the feed spout and is fed tangentially to the screen. It is important that the feed should contact the surface immediately at the front end of the sieve bend. It is possible to lose as much as 250Jo of screening area with a poorly fitted screen box.The full stream of coal slurry flowing over the sieve bend decreases in depth, in increments of approximately •;4 the slot width each time it passes a slot. Sieve bends make a size separation at 112 to 2h the slot width. This feature virtually eliminates blinding of the screen surface. Slot sizes are normally quoted in millimetres, available standard slot sizes are from 2 mm to 0.125 mm. The sieve bend is also widely used in coal preparation for preliminary dewatering."

Jan 1, 1989

By P. Coursol

The Noranda Reactor Process (NRP) has been in operation now for more than 30 years and this mature process has attained a high level of performance. The NRP at the Home Smelter of Xstrata Copper treats a wide range of feed materials and a thorough knowledge of both process control and smelting physico-chemistry has been beneficial to help meet the required plant flexibility. In this regard, some level of predictive knowledge related to slag chemistry, in particular, the liquid and solid phases such as spinels or olivines, has been found to be beneficial. In the last decade or so, the availability of commercial thermodynamic modeling packages, such as Factsage1m have been utilized with advantage to help the plant optimize slag chemistry and minimize problems from difficult slags, for example, those the could arise from undue feed variability. This paper illustrates the application of this software in examining a range of operating parameters such as: %Fe in product matte, the %Fe/%Si02 ratio in the slag, the levels of minor slag components including CaO, Ah03, ZnO, and MgO, and the level of oxygen enrichment on the operating conditions of the NRP. The slag composition boundaries at the conditions affecting magnetite control and solid magnetite/other precipitated solid phases, as well the conditions influencing the slag liquidus ranges of NRP slags are also discussed with respect to the overall process chemistry.

Jan 1, 2007

By Eric Poulin, Anthony Clapperton, Jocelyn Bouchard, Jaime Cristobal Rojas-Montes, Benjamin Legare

"Several grinding mill dynamic simulators have been developed in the last half-century. However, complete circuit simulations are mainly limited to academic investigations, and on-site applications for advanced control or real-time optimization are scarce. One particular issue that has certainly curbed a more widespread use is the time and efforts required for model calibration. This paper illustrates this challenge and presents a calibration method based on dynamic simulation using industrial data and laboratory testwork. The simulator models discussed originate from the work of Austin and Luckie (1972) for grinding mills, and Plitt (1976) for hydrocyclones. A two-stage approach based on a least squares minimization allows determining calibration parameters values. Firstly, laboratory testwork are required for characterizing breakage coefficients of the ore. Secondly, step change responses and their simulation— effect of ore and water feed rates on output flow rates and size distributions—allows identifying transport/mixing conditions. Simulation results are in agreement with actual process responses to variations of feed conditions obtained from a plant survey.INTRODUCTIONDynamic models for grinding circuits has been intensively studied since the 1970's notably by Austin and Luckie (1972b), Klimpel and Austin (1984), Rogovin and Hogg (1988), Napier-Munn et al. (1996), Liu and Spencer (2004), and King (2012) among others. The resulting models primarily serve in simulation applications for process equipment sizing, which incidentally also helps developing a better understanding of comminution operations. An obstacle curbing a more widespread and targeted use of grinding simulation for process control and optimization purposes is the time and efforts required for dynamic model calibration. It remains a cumbersome task that is typically not well detailed in technical papers. This could explain why dynamic process simulators are mainly confined to academic applications."

Jan 1, 2016

By V. Barranco, K. Yliniemi, A. Hubin, B. P. Wilson, D. Janas, M. Lundström, P. Hannula

Typical copper electrorefining electrolyte contains tens of grams of copper, some nickel and a wide variety of impurities. Some of these impurities comprise trace amounts of dissolved precious metals like Ag, Pd and Pt that currently are not fully exploited. This study presents an electrochemical method to recover precious metals via a combined electrodeposition-redox replacement (EDRR) process, where energy is used only to deposit copper during the ED-step, while the RR-step relies on the spontaneous replacement of copper by the precious metals (i.e. cementation). In order to conduct the recovery successfully, process parameters such as deposition potential (EDE), deposition time (tDE), redox replacement time (tRR) and the number of cycles (n) was adjusted. Investigations performed in synthetic electrolyte (40 g/L Cu, Ag = 10 ppm) proved the possibility to recover a high purity silver. Short deposition times (tDE) were found to result in small Cu particles that provided a suitably high surface area for silver cementation. In addition, experiments performed in real industrial electrolytes containing 44 g/L Cu and 54 ppb Ag (Boliden Harjavalta, Pori), demonstrated that EDRR could attain Ag recoveries of between 46–67% in an energy efficient, additive-free manner. INTRODUCTION The raw materials used in the state-of-art primary and secondary copper smelters contain mainly base metals, but also notable amounts of Ag, Pt and other precious metals. These valuable metals distribute mostly into the copper matte during the pyrometallurgical treatment (Tirronen et al., 2017) and end up into the cast anodes. During the electrorefining stage, metals more noble than copper such as gold and platinum, are not dissolved but enrich into the anode slimes. In contrast, silver may dissolve slightly and thus, minor chloride addition is used to retain silver in the slime as sparingly soluble AgCl. Moreover, other metals less noble than copper may also dissolve, such as nickel. Therefore the electrolytes used in electrorefining typically contain substantial amounts of copper, nickel and even arsenic as well as minor metals such as antimony and bismuth. In the Boliden electrorefinery these were reported to be in the magnitude of 51.2– 60.4 g/L of Cu, 10.9–15.8 g/L Ni, 7.2–15.9 As, 0.2–0.4 Sb and 0.1–0.4 Bi with an associated sulfuric acid concentration of 139–155 g/L (Lehtiniemi et al., 2018). Copper is the most noble of the dominating base metals in the electrolyte and is thus deposited on the cathode as 99.99% purity LME-A grade. Anode slimes are collected and subjected to precious metals treatment e.g. via pressure leaching—selenium recovery— Doré smelting—Ag refining—Au/Pt/Pd leaching and reduction process (Ludvigsson & Larsson, 2003). The Pori refinery, operating in Finland since 1941, not only produces 133 000 t Cu cathode and 2300 t nickel sulphate annually but also 66 t silver, 4.6 t gold and palladium and platinum (in year 2017).

Jan 1, 2019

By L. B. Smith

Introduction The property of Wright-Hargreaves Mines, Limited is situated at the northeastern end of Kirkland lake, Ontario. It lies immediately east of the Lake Shore mine, and about in the centre of the Kirkland Lake camp. The district is served by the Swastika-Rouyn branch of the Temiskaming & Northern Ontario railway, the town of Kirkland Lake being four miles northeast of Swastika, which is 63 miles north of Cobalt and 392 miles north of Toronto. The mine is developed by three shafts and has more than twenty-eight miles of underground workings. There are two main producing veins, which lie in a porphyry boss 1,350 feet wide. Milling started in May, 1921, and to-date (January, 1933) the mine has produced gold to the value of $21,770,183. Present production is at the rate of 800 tons of ore per day. For a description of the geology, reference may be made to the report by E. W. Todd on the Kirkland Lake Gold Area (1). Structure and Ore Deposits The two major productive veins on the Wright-Hargreaves property are known as the North vein and the South vein. In the vicinity of the shafts these veins are approximately 550 feet apart. A third vein, known as the Inclined vein, has been worked from its junction with the South vein at the 2,000-foot level to its intersection with the North vein at the 800-foot level. This inclined vein has to date been found only in the area east of the eastern major north-south fault. The main North vein and South vein have a general vertical dip, although local rolls and post-ore faults throw certain sections out of line. From the surface to 3,900 feet, the North vein is displaced south less than 200 feet, and the South vein at the same horizon is almost perpendicularly beneath the surface showings.

Jan 1, 1934

By M. Nzotta, L. Teng, S. Seetharaman, A. Chychko

The objective of the present work is to optimize the EAF practice towards Mo alloying with maximum retention of the alloying element in molten steel. During Mo additions, there were significant losses to the dust (ca 7 %) and to the slag phase (ca 2 %), which had serious economic and environmental impacts. The present work was aimed at designing a suitable Mo precursor, an alternative to ferromolybdenum, as the Mo source and a process sequence for optimal retention of Mo in the steel. The design of the Mo source should be in such a way that low cost raw materials such as MoO3 concentrate have to be used, stable during the addition so that the vapour phase losses as MoO3 are kept minimum and the dissolution of the precursor in molten steel is easy without loss to the slag phase. After thermodynamic considerations, three precursor materials were chosen, viz. CaMoO4, MgMoO4 and Fe2MoO4. Synthetic mixtures of the component oxides in each case as well as pure MoO3 were investigated by TGA and high temperature XRD in order to find out the temperature range in which the compounds were formed. Experiments were also conducted separately where the evolved gases were analyzed. All the three precursors were formed easily and the loss of MoO3 to the vapour phase was found to be extremely low. Addition of the oxide mixtures to steel melts were conducted in three different scales, viz. 16 g, 500 g and 3 tons (induction furnacle). Initial experiments showed that MgMoO4 was not suitable since the Mo yield in the steel melt was not very high. Fe2MoO4 was found to perform best, the Mo yield reaching 98 %. Further trials were conducted in the 65 ton Electric Arc Furnace (EAF) at Uddeholms AB in Hagfors. Mixtures of mill scale, MoO3 and carbon in suitable proportions were added in a pre-determined addition sequence. It was found that, in the actual practice, the Mo yield reached 99 %, equaling in performance the addition of ferromolybdenum. The process offers an effective use of cheaper raw materials and very high Mo yield avoiding a pre-treatment step like the production of ferromolybdenum. This is both cost effective and environmentally advantageous. The process has been patented and is being currently implemented at Uddeholms AB, Hagfors, Sweden.

Jan 1, 2011

By R. V. Kumar, C. Schwandt, S. Subramanian, S. Sampath, S. Vimalnath

Waste waters and industrial effluents containing toxic heavy metals such as Pb, Hg, As and Cr, beyond permissible limits (0.1 ppm, 0.01 ppm, 0.02 ppm and 0.05 ppm, respectively) (WHO, 2011), pose serious threats to the ecosystem, when discharged into the environment. It thus becomes imperative to monitor the concentration of the toxic heavy metals and treat them before discharging. In this study with the above objective in mind, a microbial sensor has been developed using P. aeruginosa cells drop coated onto a carbon paste electrode (CPE) for the detection of Pb(II) ions in aqueous solutions. Detailed biosorption experiments confirmed that complete bioremoval of lead could be achieved using P. aeruginosa cells under optimum conditions of pH and biomass loading. For the electro-analytical determination, the Pb(II) ions were initially preconcentrated on the P. aeruginosa modified CPE, reduced and then anodically detected with oxidation of Pb0 using differential pulse anodic stripping voltammetry (DPASV) technique. All the experiments were carried out in the presence of 0.1 M sodium acetate buffer and KNO3 as background electrolyte. The parameters namely pH, scan rate, biomass loading, deposition potential, deposition time and concentration of Pb(II) ions were optimized for the biomass modified CPE, to obtain maximum voltammetric response. Under the optimized conditions of pH 5.6, scan rate of 0.008 V/s, biomass content of 1.7–1.8×109 cells/mL, deposition potential of –1.2 V, and deposition time of 500 s, the developed microbial sensor showed a linear response for the peak current between 0.5×10-5 M and 1×10-8 M of Pb(II) ions with the R2 value of 0.9979. The lowest limit of detection (LLOD) was determined as 2.4×10-7M of Pb(II) ions (0.05 ppm). The redox mechanisms of Pb(II) ions on the P. aeruginosa modified CPE surface are discussed.

Jan 1, 2016

By I. Filippova, L. Filippov

"The by-product potential of light rare-earth elements (LREE, La, Ce, Nd) and rare-metals (W, Nb, Sn) within the St Austell kaolin deposits (UK) is related to the kaolinisation process, which liberates the accessory heavy minerals of the host granite in the clay matrix and allows their separation in the waste streams. As a consequence these minerals are pre-concentrated in the micaceous residue which displays relatively high LREE content (around 170 ppm) hosted by monazite which is mainly distributed (up to 95%) in the -100 µm fraction. A combined gravity/flotation concentration flowsheet, starting with classification of the residue into 3 size fractions (+150 µm, 150-53 µm and -53µm) was developed. This study presents the results of the clay-rich -53 µm size fraction beneficiation by flotation using sodium oleate and hydroxamate as collectors.The effect of dispersant addition during de-sliming operations on flotation efficiency was also investigated. The LREE grade in the floated product obtained with sodium oleate increased from 3370 ppm to 5350 ppm and recovery from 30% to 80% with dispersant which is attributed to clay coating. Comparison of flotation performance and Falcon Ultra-Fine (UF) concentration of monazite to previous results obtained with Falcon Semi-Batch (SB) gravity concentrator on the unscreened raw residue clearly shows that flotation of the fine residue is more efficient than Falcon UF and Falcon SB. Indeed Falcon UF produced high recoveries (87-95%) but with almost no enrichment (1.3-1.4 ratios) whereas Falcon SB concentration of unscreened residue produced higher grades (up to 0.6 % LREE) but with low recoveries (17-22 %). These preliminary results show that LREE can be pre-concentrated suggesting that the micaceous residue stream (and the associated tailings dams) could be considered as a potential resource for these metals."

Jan 1, 2016

By H. W. Leon, F. J. Ellis

"This paper covers the new six-strand curved-mould billet casting machine at the Contrecoeur Works of SidbecDosco. It commenced production of 3 Yz-in. square billets at the beginning of January 1972. Together with two 100- ton ultra-high-power electric furnaces in a new meltshop, it is the principal source of billets for the existing rod and bar mill also located at Contrecoeur. The paper develops the reasoning for casting-to-size 3Y2 -in. billets and for choosing a six-strand machine. It indicates the significance of Sidbec-Dosco Montreal Works' extensive experience in operating a four-strand curvedmould billet machine since 1965 and the ways in which this experience influenced the design and operation of the new caster. Machine features are described in detail, as are the reasons for some of the features. The installation, checkout and crew training are briefly discussed as well as the tundish teeming trials. The first cast on January 5, 1972, is covered and a log is shown of the first casts to an empty ladle. There are operating statistics covering the first 100 casts, which produced 8000 tons of good billets in ten weeks of operation. Machine performance and billet quality were good and the few minor problems encountered are described."

Jan 1, 1973

By Angus D. Campbell

Introduction Gowganda forms part of the general Cobalt area. Its rocks and ores are very similar to those of the other parts of the area. While its total production of silver is only 4 per cent of that of the famous Cobalt silver camp, its 1928 shipments contained 42 1/2 per cent as much silver as those of Cobalt for that year. During twenty years of production, 15,000,000 ounces of silver have been shipped from Gowganda. Of this, over 8,000,000 ounces have been shipped in the past five years. The area has thus made for several years a substantial contribution to the wealth of Ontario. Its future depends to a great extent on the priee of silver, which is now, unfortunately, at a record low price. This paper is a discussion of how the Gowganda ore-shoots occur, together with some notes on the milling of the ores at the Castle-Trethewey Mines. The first part is written in the hope of stimulating further study of the silver occurrences, which may lead to further discoveries. The second part, besides being a matter of record, may be of some use to operators of small mills. The drawings in the several Figures illustrating the text are by W. D. Stroud, mine superintendent of the Castle-Trethewey Mines, the benefit of whose opinions I have had in compiling these notes.

Jan 1, 1930

By Oleg G. Tovmachenko

We have studied optical properties of fluorescent nanoparticles. These particles consist of a metal (gold/silver) core, an empty and a dye labelled silica shells. The different dye molecules with moderate quantum yields (about 0.3) has been used. Almost all of types of nanoparticles show fluorescence enhancement. This enhancement is strongly dependent on the degree of the overlap between the surface plasmon band of the metal and the absorption/emission band of the dye molecules. The results are interpreted in terms of competition between local field enhancement and quenching of fluorescence by the metal surface.

Oct 1, 2003

By I. Yutronic

Compañía Minera Doña Inés de Collahuasi's (CMDIC) Concentrator Plant is located at 4300 meters above sea level, approximately 2000 kms north from Santiago, Chile. The concentrator has three grinding lines. Each one, Lines 1 and 2, have one SAG mill at the primary grinding stage followed by a secondary grinding and classification stage consisting of one ball mill, two hydrocyclone batteries and a sump with two pumps. Line 3 has one SAG mill (Gearless Mill Drive), followed by a secondary grinding and classification consisting two ball mills, four hydrocyclone batteries and a sump with four pumps. Average throughput for these three lines is 150 Ktons per day. Peak values of 180 ktons per day have been achieved. Since late 2008 and throughout 2009 and 2010, Operations and Automation areas developed an optimization program for the grinding process, considering the implementation of Model Predictive Controllers (MPC) for the three SAG mills, and later, extending MPC to the secondary grinding and classification stages. The implementation of a MPC solution was based on stability considerations (high variability of the SAG process, high interaction between sump level control and classification efficiency, etc), requirements for an automated and consistent operation, the need to maximize throughput under timevarying scenarios and, in the long term, optimization of grinding process considering Specific Energy Consumption, among other parameters. MPC solutions had proven control robustness and strong optimizing capabilities in terms of helping in discovering new operational points and so achieving all of the aforementioned goals. On the first stage of the program, MPC implementation considered identification of dynamical process control models based mainly on historical data, in order to know the impact of a group of Manipulated Variables over Controlled Variables. Also, the impact of measured Disturbance Variables was modeled in order to take into account the high impact and interaction of these variables over the processes. At the end of this stage, 4 controllers were successfully operating for the 3 SAG mills and the secondary grinding and classification process. In response to challenges made by the working group, the second stage of the development of control applications in the grinding process required to achieve a design and implementation of a solution capable of governing the milling process, in addition to stabilization and optimization of both processes (SAG milling and secondary grinding), to integrate from a point of view of process control and automation. Therefore, in the second stage, MPC performance was continuously monitored and optimized through advanced tuning, inclusion of more process models (with proper step tests), redefinition of specific optimization criteria and adjustment to new process needs. Finally, successful MPC implementation at Collahuasi has proved that fast development and deployment of process control solutions is possible and allows immediate process stability, higher throughput, specific energy consumption reduction, and successful product size control, among many others.

Jan 1, 2012

By V. G. Papangelakis, J. E. Dutrizac, G. Azimi

A new model capable of predicting the solubility of calcium sulphate solid phases in zinc sulphate processing solutions from 25 to 95°C was developed. The model uses the Mixed Solvent Electrolyte (MSE) model of the OLI systems software to calculate the mean activity coefficients of the electrolyte species. The model was tested using recently developed experimental measurements. It was shown to predict accurately the solubility behaviour of calcium sulphate in multi-component zinc processing solutions containing ZnSO4, H2SO4, MgSO4, MnSO4, Fe2(SO4)3, Na2SO4 and (NH4)2SO4. The model can also explain the complex effect of coexisting metal sulphates on the solubility of the CaSO4 phases. The model is a practical tool for assessing the process chemistry of a wide variety of complex aqueous processing streams.

Jan 1, 2008

By R. H. Schonewille

One of the many challenges in developing new metallurgical processes is choosing the best option for validating process design parameters and establishing the process operating window. Historically this has been achieved by constructing pilot or demonstration plants of considerable size and complexity, to enable integrated operation of all key process units for a significant duration. While this would appear to be the best option for minimizing technical risk, it is often impractical from a perspective of cost, schedule, resources or bulk sample acquisition. Such an undertaking can even provide a false sense of security, as the optics of running a complete scaled-down version of a commercial plant suggest a high level of process understanding, regardless of the challenges encountered during operation. Xstrata Nickel has undertaken numerous process development and improvement projects over the past 15 years to support green field project development and continuous improvement in existing operations. The approaches used have included; computer simulation, cold flow modeling, construction of pilot test units in third party facilities, commercial plant referencing and the more conventional construction of integrated test plants. Regardless of the strategy employed, the keys to success have included; managing stakeholder expectations, involving the commercial plant design engineers in the planning stage, anticipating subsequent data and sample requirements and most importantly, constructing and operating complex demonstration plants only as a last resort. This paper provides examples of various process development approaches used by Xstrata Nickel and discusses the rationale specific to each project.

Jan 1, 2011

By Kirsten Corin, Margreth Tadie, Cyril O’Connor, Jenny Wiese, Wonder Chimonyo

"Relating flotation performance to the electrochemical characteristics of a pulp remains a complex issue both in fundamental research and in practice. For example, in the case of thiol collectors different Eh values can result in the formation of the dimer or the metal thiolate which may or may not enhance the hydrophobicity of the mineral. Reducing or oxidizing conditions in a flotation system, viz. changing the Eh value, are usually manipulated to achieve an optimum flotation response by the control of pH and dissolved oxygen levels in the system. It is also possible to vary the potential by the addition of modifiers such as sodium hydrosulphide (NaHS), sodium hypochlorite (NaClO) or hydrogen peroxide (H2O2). The objective of the present study was to investigate the effect of the addition of the oxidising agents, NaClO and H2O2, on valuable mineral recoveries and grades in the flotation of sulphides from a PGM bearing Merensky ore. Batch flotation tests were conducted at pH 9.2, the natural pH of the system, in the absence and presence of a xanthate collector and Eh modifiers, viz. NaClO or H2O2. Most importantly in this way it was possible to vary Eh at constant pH and DO levels. The results indicate that in the absence or presence of xanthate the addition of H2O2 reduced both the recovery and grade of copper and nickel. In the absence of xanthate, the addition of NaClO improved the recovery of copper slightly and both the recovery and grade of nickel significantly, but in the presence of xanthate NaClO addition resulted in unchanged copper recovery and grade, but those of nickel were reduced. Based on anecdotal evidence that the addition of trace amounts of a potential modifier could improve flotation performance further tests were conducted the results of which suggest improved flotation performance.INTRODUCTIONIn the Merensky Reef, platinum group minerals (PGM) are commonly associated with base metal sulphides (BMS) and this has an effect on the way in which these minerals can be concentrated by flotation (Vermaak, Venter & Pistorius, 2004; Wiese, Harris & Bradshaw, 2005; Schouwstra, Kinloch & Lee., 2000). A major problem stemming from this association has been reported to be the loss of valuable minerals (PGM) associated with the loss of BMS (Wiese et al., 2005) during flotation. Shackleton (2007) suggested that PGMs behave in a similar manner to sulphides during flotation. Therefore, in order to recover the PGM, base metals are targeted. There is thus a need to investigate ways to improve the flotation performance of the sulphide minerals. The electrochemistry of the flotation of sulphide minerals has been studied for over half a century and there is consensus that sulphide minerals float only under a suitable redox environment (Heyes & Trahar 1979). This implies that reducing and oxidizing conditions during flotation of ores such as Merensky can be manipulated/varied to achieve an optimum flotation response.During flotation, sulphide minerals interact with thiol collectors in an electrochemical reaction to form hydrophobic species at the mineral surface (Finkelstein & Goold 1972; Rand & Woods 1984). The sulphide minerals are semiconductors and their interaction with collectors involves transfer of electrons. As such, a potential difference results which is responsible for driving electrons between reacting species (Fuerstenau, Jameson & Yoon, 2007). The magnitude of the potential difference affects the relative energies of charge carriers (electrons) at the mineral/solution interface hence controlling the direction and rate of charge transfer or rate of reaction (Bard & Faulkner, 2001). In a mixed mineral system the mineral/solution interface potentials account for the mixed potential which is critical to the process of flotation (Chander, 2003; Woods, 2003)."

Jan 1, 2016

By F. Chevarin

The reaction of O2 with the carbon anode is considered as the main parasitic chemical reaction affecting Hall-Heroult process anodes. The current study aims at investigating the influence of the microstructure of baked anode on its overconsumption. Samples were removed from different positions of an industrial anode. Density, porosity, Lc and BET specific surface area were measured. The anode reactivity was evaluated based on the weight losses for the samples resulting from the reaction of anode with air at 550°C after 7h. The essential parameters determined to control the air reactivity are closed porosity, Lc and pores with a pore entrance radius of 1.5, 8.5 and 12 p.m. The knowledge of effects of these parameters allows better understanding of the reactivity of anodes and consequently reduction of their overconsumption in electrolysis bath.

Jan 1, 2011

By T. Krumins, L. Zunti, R. Frischmuth

Mercury is known to occur in sulphide-bearing refractory gold deposits in the form of sulphide minerals or elemental inclusions. These deposits typically require an oxidative pre-treatment process, such as pressure oxidation or roasting, to achieve economic gold recovery. However, these processes also have the potential to liberate mercury, a portion of which may then be released to the environment through gaseous emissions. Mercury emissions from mine processing operations have been of particular interest in recent years, as governments impose lower emission targets and organizations adopt better industry practices to reduce the environmental and health aspects of releasing mercury into the environment. This paper describes various mercury removal technologies with respect to pressure oxidation gas handling circuits, with a focus on key design variables and technology selection criteria.

Jan 1, 2014

By K. K. Mamyrbayeva, G. Z. Guseinova, V. A. Luganov

This paper presents the results of theoretical and technological studies on leaching ore of Bozshakol deposit. The major oxidized copper mineral of Bozshakol ore is atacamite, and the content of malachite, azurite, cuprite, copper sulfide minerals is insignificant. The chemical composition of the test sample, with mass, %: 0.9 Cu; 55.00 SiO2; 22.40 AI2O3; 9.00 Fe2O3; 2.24 CaO; 3.56 MgO. Technological studies on leaching the ore were carried out with sulfuric acid 5, 15, 25 and 50 g/dm3 in one and multistage (up to 4 stages) countercurrents. Size of ore 1 mm, the ratio S : L 1: 4. It was found that with increasing of acid concentration from 5 to 50 at one-mode leaching the copper extraction reaches 55 %. At multistage leaching the copper recovery reaches 73 %, a productive solution containing g/dm3: Cu - 4; Fe – 1.2; Al – 1.1 at a pH of 2.8. When leaching the cinders obtained by ore roasting in an atmosphere with limited value of oxygen, with increasing of the roasting temperature from 650 up to 750 °? the extraction of copper from the Bozshakol ores reduced from 31.5% down to 24.4%. The rate of filtration is markedly increased compared with the crude ore. When leaching the cinders obtained by roasting in a nitrogen atmosphere a marked increase up to 87.2-88 % of copper extraction from Bozshakol ores is observed. As an extractant for the extraction of copper from the pregnant solution used LIX984N extractant in kerosene. On the basis of the calculations it was built extraction isotherm and modeled processes of copper recovery with the circuit 2E + 1P, allowing up to 93 and 96% extraction. The through extraction of copper from the ore in the electrolyte was 67 %. Technology is recommended for semi test.

Jan 1, 2016

By Sakellariou M., Ferentinou M.

Determination of the nonlinear behavior of multivariate dynamic systems often presents a challenging and demanding task. Therefore, complex geomechanics systems are an ideal area for the application of intelligent methods. Often the physical problem is controlled by nonlinear equations, conveying to the use of neural networks. Hudson, (1992a), aiming at efficient engineering modelling and design, introduced and developed Rock Engineering Systems (RES) approach, through the implementation of generic interaction matrix GIM. This approach has been used for a wide variety of rock engineering and other problems, resulting in many case studies available, which illustrate the application of RES to rock engineering problems. Considering the spectrum of the coding methods for the Generic Interaction Matrix, we suggest an objective coding approach. Among the five proposed coding GIM methods, the coding method according to the slope of Pi and Pj relation is relatively accurate, but it might be difficult or impossible to establish or estimate the exact relation of Pi vs Pj for most of the variables involved within a rock engineering system. Self organising maps, are a special type of unsupervised artificial neural networks, which can learn from complex, multidimensional data, and transform them to visually decipherable clusters. The proposed, coding of the GIM, is performed through the combined use of scatter plots produced through, (SOM), and the coding according Pi vs Pj slope. Naghadehi et al., (2013) constructed a database of worldwide experience, in open-pit mine slope stability, the selection of the principal factors was based on Hudson (1992a) who proposed an ‘atlas’ of factors affecting the stability of rock slopes. Slope classification was performed according to status of stability. The rating of the GIM matrix was completed, coupling scatter matrix produced by SOM training, and Pi vs Pj slope plot. Results refer to the identification of clusters, according to status of stability within the original multivariate data set, and the rating of the principal factors according to the dominance and interaction intensity within the open pit mines RES.

Jan 1, 2015