Search Documents

By K. Kawagishi, J. Ang, A. Sato, H. Harada

"We have recently proposed a new ""EQ Coating"" bond coat system to solve the problem of secondary reaction zone (SRZ) formation caused by bond coats applied on the hot section components of modem jet engines. A viable EQ coating alloy was previously found for a representative znd generation superalloy, TMS-82+. It would be ideal if the same could be done for a representative 5th generation superalloy, TMS-173. In this paper, we will show that the coating with the best oxidation resistance in the EQ system of TMS-173, although possessing considerably better resistance than TMS-173, did not have sufficient oxidation resistance. In order to improve the oxidation resistance of the EQ coating for TMS-173, we have ventured into ""Pseudo-EQ coatings"". A diffusion couple between the Pseudo-EQ coating and TMS-173, after 300hrs at 1100°C, had a 0-15µm IDZ, but no SRZ. A diffusion couple between a conventional coating and TMS-173 formed a 80-150 µm SRZ. After a 1 hr oxidation test at 1100°C, the PseudoEQ coating formed a thinner oxide layer than the EQ coating, but still contained NiO and spinel. Aerospace"

Jan 1, 2006

By K. van Netten, T. P. Ernst

"Froth flotation has been used successfully for about a century in the beneficiation of both coal and mineral particles. With the on-going trend towards lower feed grades, however, there is a need to transform this technology in ways that can deliver ultrafast separations, with strong selectivity, and recovery, covering a broader size range. It should be recognised that the hydrophobic effect, with its highly selective and long-range interactions, will most likely underpin any new technology. We identified the separation of the concentrate from the tailings as the rate determining step of conventional flotation technology. This limitation was then addressed by developing a novel flotation technology, insuring the formation of a concentrate that could be separated more rapidly from the tailings. We introduced a novel binder medium, a highly concentrated water in oil emulsion, to act as the focal point for hydrophobic adhesion, effectively replacing the air bubbles used in conventional flotation. The hydrophobic particles adhere to and become embedded within the binder, forming saturated agglomerates that float upwards. Moreover, by forming these large and resilient agglomerates, the product can be quickly dewatered over a screen and separated almost immediately from the tailings. Remarkably, this new binder permits residence times in the order of a few seconds under batch conditions. This paper examines the performance of the technology as a function of the oil wt% added to the slurry. The paper also examines the performance of the technology as a function of the particle size, showing a decline as the particle size exceeds 0.50 mm.INTRODUCTIONFroth flotation involves the collision and adhesion of hydrophobic particles to rising air bubbles, the carrying of those particles from the bubbly-pulp zone into a froth zone, and subsequent drainage and migration of the pulp to achieve the final concentrate (Wills, 2006). Within a Jameson Cell the feed slurry and air bubbles are brought into intense contact within the active area of the downcomer, achieving rapid kinetics of hydrophobic particle adhesion to the air bubbles (Harbort et al., 1994). However, once the bubble laden product and tailings emerge from the downcomer there is the need for separation of the concentrate from the tailings, an inherently slower process. In other devices such as mechanical cells the initial kinetics of particle adhesion are far slower, relying on the turbulent eddies throughout the cell, while in a column the kinetics rely upon an even slower process of bubble interception with suspended and settling particles (Gorain, 2007). However, in all cases the driving force for segregating the bubbles from the tailings, and the drainage of the froth are inherently the same. We do note, however, recent advances by Galvin and co-workers in achieving so-called Fast Flotation, utilizing a system of inclined channels to dramatically increase the segregation rate of bubbles from the tailings, permitting much higher gas and feed fluxes to be applied, achieving up to a ten-fold throughput advantage (Dickinson et al., 2014). Any further improvement within the existing flotation paradigm would require the introduction of centrifugal forces, but this would also require the formation of much finer bubbles than is typically used given the tendency of relatively large bubbles to reach a limiting slip velocity due to deformations and increased drag. Across all flotation devices we argue the rate determining step remains the segregation of the bubbles from the tailings."

Jan 1, 2016

By Jim Hazzard

A numerical investigation is presented to examine fluid flow in fractured rock slopes. In mining geomechanics, different numerical modelling approaches are used to estimate fluid pressures in open pit mines. The most common technique is the Equivalent Porous Medium (EPM) approach in which the fractured rock is assumed to behave as a porous continuum. Depending on the geometry and properties of the problem, this may not always be the best approach. The paper presents a parametric study to examine the effect of fracture spacing, fracture and matrix diffusivity and excavation rate on the fluid behaviour in rock slopes. Based on the model results, guidelines are provided as to when EPM models can be used and when different modelling approaches (e.g., discrete fracture flow) may be necessary.

Jun 1, 2012

By J. C. Folinsbee, D. R. Derry

"The Property of Opemiska Copper Mines (Quebec) Ltd. is in Levy Township, Chibougamau district, west of Chibougamau and south of Opemiska Lake. The original find was made in 1929 by the late Leo Springer and associates of Prospectors Airways Ltd., following observation from the air of an area of dark rocks in newly burned-over country. Work on the ground discovered three veins of high-grade chalcopyrite in gabbro (No. l, No. 2, and ""North"") and, after several seasons of trenching and diamond drilling, financed by Ventures Ltd., a shaft was sunk in 1936. This work indicated about 280,000 tons of six per cent copper ore to a depth of 500 feet. During this period, the senior author carried out a reconnaissance geological survey over the whole property and surrounding claims, which showed that the veins were in the gabbro portion of a large composite basic sill that had been folded with the enclosing lavas. Owing to the low price of copper and lack of transport work was suspended and the property remained dormant until 1951.In that year the company was re-financed, the property prepared for production, and further exploratory drilling undertaken. The drilling, based on structural indications, located a new vein of which the only previous evidence had been some irregular stringers. This vein, No. 3, was traced by drilling for a length of 2,000 feet and the indicated reserves were thereby increased to about one million tons. An additional vein, No. 4, was intersected in several holes.With this encouragement, plans for production were confirmed, and operations commenced' at the beginning of 1954 on a scale of about 400 tons a day, concentrates being shipped by truck to St. Felicien and thence by rail to Noranda. In the first year of operation concentrates were re-covered carrying 14,047,210 pounds of copper, 76,714 ounces of silver, and 6,259 ounces of gold. The operation is under the direction of J. P. Millenbach, General Manager, with J. M. Thompson as Assistant General Manager and F. G. Cooke as General Superintendent on the property."

Jan 1, 1949

By David Deglon, Martin Harris, Mehdi Safari

"This study investigates the effect of energy/power input on the flotation of a platinum ore in a pilot-scale oscillating grid flotation cell. Oscillating grids generate near ideal hydrodynamic environments, characterised by turbulence which is relatively homogeneous and isotropic. Secondary rougher feed and primary cleaner tail streams were floated in a pilot-scale oscillating grid flotation cell at power inputs from 0 to 2.5 W/kg, using 0.50 and 1.50 mm bubbles. From this study one may conclude that the effect of energy/power input on the flotation rate is strongly dependent on the particle and bubble size. Flotation rates generally increase with increasing particle size and decreasing bubble size. Increasing energy input generally leads to an increase in the flotation rate for finer particles and an optimum flotation rate for intermediate & coarse particles. Optimum conditions for intermediate/coarse platinum ore particles are using small bubbles at low energy inputs, or large bubbles at higher energy inputs. These results suggest that higher energy inputs are generally beneficial for the flotation of platinum ores as these consist predominantly of finer particles (-75 µm) and most industrial flotation applications operate with larger bubbles (1.0-2.0 mm).INTRODUCTIONThere is a considerable body of experimental and theoretical evidence to suggest that energy/power input plays an important role in flotation kinetics, particularly in the finer particle sizes where flotation efficiency is poor (Deglon, 2005). A number of excellent studies into the effect of energy on flotation kinetics have been carried out in impeller stirred cells (Ahmed and Jameson, 1985; Deglon, 2002; Pyke et al., 2003; Newell and Grano, 2006). Investigations using this type of cell have a number of limitations. The impeller influences particle suspension, bubble break-up and agitation in the cell. In addition, turbulence is highly inhomogeneous and anisotropic, with power intensities near the impeller orders of magnitude higher than those found elsewhere in the cell (Deglon, 1998; Koh and Schwarz, 2003; Schubert, 1999, 2008). These limitations have resulted in the development of novel cells for the investigation of energy input."

Jan 1, 2016

By A. W. Jacobs

SHORTLY after Denny, Robson, and Irwin(l) published their first paper, in 1937, on the prevention of silicosis by metallic aluminium, experiments were begun on the practical application of the discovery. It was thought at that time that aluminium powder, to be effective in aluminium therapy, would have to be intimately admixed with siliceous dust at the latter's source. There followed several years of experimental work underground, during which the application of aluminium powder was tested in: (1) Shakers on machine columns, vibrated? by drills (2) Vials placed in drill holes to be blasted (3) Both homogeneous and heterogeneous. mixture with explosives ( 4) Packages with tamping (5) Compressed-air lines (6) Special compressed-air ejectors for use while drilling and after blasting (7) The discharge of ventilation fans (8) The filters of respirators It was concluded from this research that any adequate method of introducing aluminium powder into a mine atmosphere would require too much extra gear, supervision, and aluminium powder, and would interfere unduly with underground routine. Later, animal experiments by Denny, Robson, and Irwin(2) showed that aluminium powder provided effective therapy when inhaled independent of silica dust. Therefore, some means of surface treatment was deemed more practical.

Jan 1, 1944

By Richardson A. H.

"IntroductionSafety and training in the mineral industry will always be issues that are hotly debated and discussed.The nature of the mining industry, where people and equipment work in close quarters deep below the earth's surface, attracts a great deal of public attention and concern, especially in the areas of safety and related training activities. This concern has been carried over into the mineral processingsector which is, of course, a vital part of the mining industry.It is therefore imperative that mining people closely examine the policies, procedures and programs presently in place to determine if they meet the needs of the industry and its employees. Everyone stands to benefit: the companies, employees and the mineral industry as an important segment of the Canadian economy.Phrases such as ""Safety First"", ""Safety is Number One"", have a role to play in industrial safety programs but in reality are a shallow approach to the magnitude of the challenge. An industry must produce its products in a cost-effective way, with good employee relations. None of these objectives can be successfully achieved unless accompanied by good safety performance. Accidents both on and off the job result in very poor efficiency, high costs and poor employee relations.This chapter, Safety and Training, outlines those major areas that the author believes are necessary components for an industrial safety, health and training program, but are not all inclusive. More will surely be added as additional problem areas requiring attention are identified. The major sections discussed are: Development and Implementation of a Safety Program; Occupational Health; Training; and Audit Procedures.The author has drawn on his experience as both a mill superintendent, mine manager and superintendent of safety, health and training. The approach developed at loco Metals Manitoba Division is frequently used in this paper with examples and excerpts to better illustrate the subject, but does not represent the full scope of programs in place in the Division."

Jan 1, 1989

By Tim Watson

Andacollo Hypogene Project ?Overview Project description: Sulphide copper concentrator Throughput:55,000 tpd Location: Approximately 50 km from La Serena Elevation: Approximately 1,000 m ASL Start feasibility study: July 2005 Start of construction: May 2007 Construction completion: December 2009 Final cost(1,2,3):435 Million US $ (1) Excludes third party costs, 220 kV power line (2) Cost is based on a Chilean Peso to US Dollar foreign exchange rate of 535 to 1 (3) Does not include US$40.3 million for the Elqui River Pipeline Project or US$8.0 million for the stock pile cover

May 1, 2010

By Patrick Rennkamp, Wolf-Dieter Trodel, Andy Fearn

"The Jansen shafts are completed using purely mechanical excavation. This paper summarises the geology, a description of the shafts, the method used for excavation and the results achieved along with the challenges encountered and the solutions developed during the project. This experience is now being applied in the next generation machines and shaft sinking processes. This pioneering approach is changing shaft sinking in soft and medium to hard rock. INTRODUCTION The Jansen Mining project located approximately 150 km east of the city Saskatoon is the location of the BHP owned potash mine with an expected mining output of eight million tonnes annually upon completion. Mining contractors DMC Mining Services have used two Herrenknecht Shaft Boring Roadheaders (SBRs) to excavate the two blind shafts with an approximate excavation diameter of ten metres (inner diameter approximately 8.3 m) to depths of -975 and -1005 metres, respectively. The SBRs excavate the rock by a partial-face cutting method, using a transverse cutting drum mounted on a telescopic boom. The excavated rock is then conveyed away from the bench by an innovative pneumatic system and transferred into muck buckets to be hoisted to the surface. No drilling and blasting was done to keep to the BHP philosophy of using only mechanical excavation for this reference project. BHP VISION – MECHANICAL EXCAVATION BHP focused on mechanical excavation at Jansen due to the following perceived benefits: 1.No workers in the excavation chamber (shaft bottom), minimizing the exposure to traditional shaftsinking hazards associated with working in the shaft bottom. 2. Minimal damage to the rock fabric reducing the need for ground support and avoiding potential impact damage to freeze tubes located around the shaft. 3. Accurate excavation diameters with no overbreak, reducing volumes of rock to be removed and replaced with concrete lining."

Jan 1, 2019

By Nelson Hogg

"THE NOR-ACME gold mine is located close to the north shore of Snow Lake, at 54°53' north latitude and 100°03' west longitude. It is about 75 air miles east of Flin Flon, and 36 miles by road from Wekusko at Mile 81 from The Pas on the Hudson Bay Railway.The claims which contain the Nor-Acme orebodies were staked in 1927 by C. R. Parres, who, with his sons, held the ground until 1938 when Nor-Acme Mines Limited was incorporated. In 194 l, on the recommendation of F. Ebbutt (1), this property was optioned by the Howe Sound Exploration Company, Ltd. A program of 50,000 feet of diamond drilling resulted in the outlining of two orebodies containing an estimated 5,000,000 tons with an average grade of 0.15 ounces per ton to a depth of 1,000 feet.A period of inactivity during the war years was followed by the construction of a mining plant capable of treating 2,000 tons of ore per day. Milling started in March 1949, and to the end of 1954 has resulted in the production of 383,793 ounces of gold and 32,906 ounces of silver from 3,331,403 tons of ore.General GeologyThe general geology of the Snow Lake area is described by J. M. Harrison (2), and will not be discussed here except insofar as it affects the Nor-Acme orebodies. The orebodies occur in rocks of Precambrian age that have been classified by Harrison as the Snow group, comprising meta-morphosed sediments interbedded with acid and basic volcanic rocks. The volcanic rocks include pyroclastic types which are unique in the region, a fact which led to their classification in the Snow group rather than the more widespread Missi group that generally occupies the same stratigraphic position above the Amisk group (Figure 1)."

Jan 1, 1949

By G. S. Hume

Dr. K. A. Clark: No one will doubt the statement of fact that, during drilling operations through the bituminous sand beds in the Mildred-Ruth Lakes area, the core-barrel was found to contain bitumen with minor amounts of sand instead of bituminous sand. But many will doubt the interpretation of this fact as meaning that beds of bitumen occur interstratified with the bituminous sand beds. They will prefer to hold faith in the laws of physics, which deny that sand will float on oil or that fluid under pressure will not flow away through a permeable medium, until it is proved that the appearance of the oil in the core-barrel was not due to circumstances surrounding the drilling of the bituminous sand beds. The implication of the interpretation that sand is floating on oil is clear and it is unacceptable. Bituminous sand is unconsolidated sand more' or less saturated with a viscous oil. It is as difficult to conceive of bituminous sand lying on top of a body of the viscous oil as it is to conceive of unconsolidated sand more or less saturated with water lying on top of a body of water. The only difference between the two concepts is that the oil is viscous whereas the water is fluid. Oil-soaked sand placed on viscous oil would, when released, sink through the oil slowly, whereas water-soaked sand would sink through the water quickly.

Jan 1, 1947

While this paper is directed towards the ?Bellambie? type of rope attachment, the principles can be applied to any brand of rope fitting however, it is a only a broad outline and the specific installation and maintenance procedures can be obtained from the attachment supplier. The types of attachment to be discussed are:- ?Thimble Type rope cappel ?Wedge Type cappel ?WRC Rope Clamp ? (Rope Glands) ??Hoist and Balance Rope Sockets In each case, the assembly and stripping (disassembly) plus the basic maintenance procedures is briefly described. A guide for Risk Assessment is also included but because of his familiarity with the installation, the end-user is in the best position to draft the final version.

May 1, 2003

By J. R. MacDonald

MINING literature contains very few descriptions of operations producing as little as 25 to 30 tons of ore per day. The purpose of this paper is to discuss the gradual development of a mining method for such a small-scale operation at the No. 2 mine of Central Patricia Gold Mines, Limited, and in doing so to review several systems of stoping applicable to narrow ve1ns. MAIN ECONOMIC FACTORS TO BE CONSIDERED (1) Overhead.-The outstanding feature of most mines operating on a single narrow vein is chat of small daily tonnage. The reason for this low output can be readily understood. The strictly limited ore-reserves present a condition unfavourable for a policy of large initial expenditures, with the result that the capacity of the plant provided must be governed by the? amount of ore in sight at the time when mill construction is planned. This is immediately reflected in the cost per ton, there being relatively few tons over which to distributed the more or less static charges, such as hoisting, heating, supervision, administration, pre-production expenses, and other write-offs. (2) Development.-In mining this type of orebody, the main factor contributing to high costs is unquestionably the small tonnage of ore made available by a given amount of development. Thus, for example, from the data tabulated below it can be seen chat, assuming a 12-in. vein and a drifting cost of $9.00 per foot, the development charge for this item alone would be 71 cents per ton. Add to this the charges for raising, cross-cutting, shaft-sinking, and pumping, besides charges arising from development in waste, and the figure will be very considerably higher than 71 cents.

Jan 1, 1941

By Hasini Wijayaratne

Anode cover material, a mixture of crushed electrolyte and alumina, is a crucial part of an aluminium reduction cell because of its important role in maintaining overall heat balance. However, until recently little attention has been given to understanding or controlling its composition and quality. The thermal conductivity of anode cover material determines the extent of the heat loss from the top of the cell. This will change as a function of the granulometry and composition of the applied cover as well as over time as the cover material consolidates on top of the cell. The ability to measure or predict the thermal conductivity of fresh and ageing cover is an important tool for managing cell heat balance. Recent studies have shown that granulometry or more correctly, voidage is likely to be the predominant determinant of thermal conductivity of anode cover materials. We have developed equipment to measure the thermal conductivity of granular cover material and tested the relative importance of composition (ratio of alumina to crushed electrolyte) and granulometry/voidage on cover thermal conductivity. In general, our results confirm that granulometry is the dominating factor. Generally, high voidages contribute to lowering the thermal conductivity especially when particles are mostly fine. However the relationships between granulometry, voidage and thermal conductivity are complex due to the varying nature of heat transfer between particles. Aging of granular cover material occur during cell operation forming a consolidated crust due to exposure to heat and fumes over time. Structure and thermal behaviour of this consolidated crust is also important in understanding the overall properties of cover. This paper presents the outcomes of laboratory studies conducted in order to understand the thermochemical behaviour of anode cover material and in particular, the role of fines in anode covers mixtures.

Jan 1, 2011

By H. Al-Kazzaz

The effects of laser power and joint gap on the welding quality of 2-mm butt joints of ZE41A-T5 sand castings were investigated using a continuous wave 4 kW Nd:YAG laser system and 1.6-mm EZ33A-T5 filler wire at a welding speed of 6 m/min and surface defocusing. The smooth weld profiles with the minor welding defects were obtained at a laser power of 4 kW and joint gap of 0.3-0.4 mm. The hardness values in the fusion zone are similar to those of the base metal but there is a drop in the heat-affected zone after a natural aging of 18 months.

Jan 1, 2006

By J. J. Ferreira, M. L. Thurston, I. L. Chinn, D. M. Rose

"Concerns about using microdiamonds for resource estimation have been raised by workers because multiple diamond populations exist in many parts of the mantle source region, small diamonds in kimberlite could be exposed to proportionately greater levels of resorption and modification, and euhedral microdiamonds could crystallize immediately prior to kimberlite eruption. This paper addresses these concerns; discusses the geology of the mantle, the principal diamond host rocks, and the impact of mantle processes; compares micro- and macrodiamond properties and features; and outlines steps to identify and mitigate the risk of diamond resorption and its impact on the diamond grade-size relationship.RÉSUMÉ Des travailleurs se sont interrogés sur l’utilisation de microdiamants pour estimer la ressource; en effet, de multiples populations de diamants existent dans plusieurs secteurs de la région source dans le manteau. Des petits diamants dans la kimberlite pourraient être exposés à des niveaux proportionnellement supérieurs de résorption et de modification; de plus, des diamants idiomorphes pourraient cristalliser immédiatement avant l’éruption de la kimberlite. Le présent article traite de ces questions, discute de la géologie du manteau, des principales roches-mères des diamants et de l’impact des processus dans le manteau, compare les propriétés et les caractéristiques des micro- et des macrodiamants et définit les étapes pour identifier et mitiger le risque de résorption des diamants et son impact sur la relation entre la taille et la qualité des diamants."

Jan 1, 2016

By Rob Kelso

What is a Lunabot? ?Robot Controlled Remotely or Autonomously ?Visual and Auditory Isolation from Operator ?Excavates Black Point 1 (BP-1) Simulant ?Weight Limit - 80 kg ?Dimension Limits - 1.5m width x .75m length x .75m height ?Designed, Built and Tested by University Student Teams

May 1, 2013

By Bryan Wilson

Background ?Nickel Rim South Mine started production ramp-up in Q2, 2009. ?The main dewatering pumps were put into use in August 2009. ?3 Feluwa?multisafe?positive displacement pumps ?1700m single lift pumping ?Reliability has been an issue due to the amount of slimes and fibers (from shotcrete) at the pumps. ?Critiqued internal dewatering system to solve some issues we were having with our sumps Findings 1.Much of the final dewatering system was not in place. a)Temporary pain. Difficult to say something is not working when the system was not yet in place as per design. b)Not enough capacity to handle slimes within the system. 2.Need to address issues with the final design: a)Ongoing costs: The end design has operating costs of $2.5 million b)Scoops in Sumps: The end design relies on scoops to be used for cleaning the sumps c)Slimes Recovery: The system mixes 3 different products in the sumps along with the fibers d)Pump repair costs: The existing Tsurumi pumps are too light duty for our slimes

Nov 1, 2011

By E. C. Keeley

Some Safety Measures at Ontario Mines The following safety precautions have of late been taken by several of the Ontario mines: installation of water crossovers; washing clown of faces to show-up missed holes; insistence on gloves being worn as a protection to men's hands; wearing of safety boots and hats by underground men; and wearing of goggles by all men using hammers, starting holes, etc. In the summer of 1924 the Mclntyre mine began experimenting with means of removing powder smoke from headings by installing fans and pipe-lines of various designs, also with different means of introducing water into the air-blast when blowing smoke. By October of that year they had devised a scheme of water connection between the water and the air line, at a distance of about one hundred and fifty feet back from the face, using two valves and a short hose. By this means a limited amount of water could be introduced into the air which blew into the face, resulting in a fine spray of air and water combined. This spray not only helped to eliminate fumes but also introduced fine particles of water into the air, raising it above the dew point, with the result that when these fine particles of water settled they had attached to them fine dust particles, thus eliminating, to a great extent, the injurious dust caused by blasting. The combined air and water is turned on immediately after blasting and allowed to blow continuously for from four to five hours, until the muckers come on shift.

Jan 1, 1931

By Frank S. Palkovits

Over the past 30 years, underground paste backfill systems have been implemented across the globe in many configurations, each with a primary focus of providing high quality backfill to enhance mine operations. However, a number of key design drivers are not always well understood within design engineering firms that occasionally undertake this work, leaving opportunities on the table. Perhaps not always obvious to those newly embracing paste technology, identifying key drivers and opportunities attainable through a paste backfill system is generally not straightforward, requiring innovative approaches to securing higher productivity, availability, performance, maintainability, and operator health and safety. This paper describes a number of applications and audits of paste backfill systems for several challenging mine operations. Key challenges include iterative design aspects of availability of good backfill materials, plant location and configuration, general arrangement, and binder receiving/storage systems.

Oct 1, 2010