Search Documents

By W. K. Smith, V. P. Krueger, D. C. Mulder

"AbstractThis paper describes the geological procedures used to evaluate two mineable high-volatile C bituminous coal seams at Coal Valley , located in the outer foothills belt of the Rocky Mountain Eastern Slopes in west-central Alberta. Lexco Testing Ltd., the exploration arm of Luscos: Ltd., owns and operates an all -weather geophysical logging system which provides gamma, focused density , single-point resistance and caliper logs in a single pass. A mathematical analysis for a theoretical interpretation of the single-point resistance log confirms empirical research that bed boundaries are located at a point 10% from the bottom of the curve. A unique and efficient triple-tube, wireline rotary coring system cuts an undisturbed 0.076m- diameter core in a plastic liner at recoveries exceeding 90% . Although only 10% of the total footage is cored, it provides vital analytical and geotechnical data, and, when integrated with the geophysical logs, improves the quality and extends the usefulness of interpreting both sets of data. All data are programmed to produce computerized structure contour, isopach, isoratio and isoquality maps, and volume calculations.General IntroductionTHE COAL VALLEY AREA is located in the outer foothills belt of the Rocky Mountain Eastern Slopes, 60 miles (96 km) by road southwest of Edson, Alberta. Luscar Ltd. holds leases which total 49,000 acres (19,830 ha) , of which 18,300 acres (7,410 ha) have been assigned to the Coal Valley mine area (Fig. 1 ) . There are two Paleocene high-volatile C bituminous coal seams initially developed for mining within a total stratigraphic interval of 750 feet (230 m ) (Fig. 2 ). These seams strike generally NW, and in the undisturbed areas generally dip westerly from 10 to 30 degrees."

Jan 1, 1977

By J. B. Mawdsley

Introduction The writer was instructed to visit the Chibougamau region during the field season of 1927 and report on the mineral discoveries that had been made there since 1911. lt was deemed advisable to obtain detailed information regarding the rocks underlying the area in the vicinity of these recent discoveries. Accordingly an area 60 square miles in extent was mapped. The outcrops were studied along the water courses and along bush traverses spaced at half-mile intervals between these water courses. The completion of the rest of the summer's programme allowed only three weeks for this work. lt is from this small, mapped area, and this necessarily cursory survey, that the material for this paper was obtained. Location And Means Of Access The name Chibougamau district is applied loosely to an ill-defined area of about 1,000 square miles lying mostly north and west of Chibougamau lake in the Province of Quebec. The lake is approximately half way between lake St. John and James bay. It lies 150 miles north of the Canadian National railway and 40 miles south of Mistassini?lake.

Jan 1, 1928

By J. Lobel, M. Bourassa, J. A. Kozinski, B. Peng

Non-isothermal kinetics studies of the reduction phenomenon of electric arc furnace (EAF) dust generated in stainless steelmaking have been carried out. The dust was mixed with carbon as a reducing agent and dolomite as a binder to form pellets. A Thermo-Gravimetric Analyzer (TGA) was used to determine the weight loss of pellets heated at an average rate of 40 K/min. up to a temperature of 1500°C. The degree of metal reduction was calculated by considering the pellet weight loss, and evaporation of moisture, dust, zinc and lead at high temperature. The reduction process was divided into three different steps. The first covers the 300°C to 760°C temperature range (from 7 to 18 min.), the second step ranges between 760°C and 980°C (18 to 24 min.), and the third covers temperatures above 980°C. Each step is characterized by different chemical reactions. Non-isothermal reduction kinetics equations were set up to describe each step. The kinetics parameters such as apparent activation energies and frequency factors were established. It was found that the first step was chemically controlled, while the second step was diffusion-controlled. Reduction behaviour in the third step was strongly dependent on the initial carbon content in the pellet. Chromium oxide (CrO) could only be reduced in this last step. High temperatures and higher initial carbon content favoured the reduction of CrO.

Jan 1, 2001

By Imane Benhamed, Jaouher Diouani, Laurent Cassayre, Florent Bourgeois, Carine Julcour-Lebigue, Université de Carthage

The attrition-leaching process aims at improving leaching performance when formation of passivation layers at the surface of leached particles is a severe limiting factor, as discussed recently by Julcour and coworkers (Julcour et al., 2015). This paper proposes a geochemistry-based modelling scheme for deriving the window of possible operating conditions for the attrition-leaching process to match the properties of the processed ore. The rationale is that the attrition-leaching process maintains the surface of reacting particles in an unpassivated state by continuous mechanical removal of surface leach layers, so that the process reactions can be modelled from thermodynamic equilibria throughout the duration of the process. The strength of the proposed modelling approach is that it bridges the gap between the properties of the ore and the process operating conditions. The present paper exemplifies the proposed process modelling route for derivation of the attrition-leaching process operating conditions in the context of the leaching of silicate ores, matching model predictions against controlled laboratory experiments. It is shown how thermodynamic modelling, when used in conjunction with a solid knowledge of the phases present in the system, can assist with deciding upon suitable process operating conditions. As an example, this firstprinciple modelling approach predicted that steel grinding medium would be converted into siderite (FeCO3) under a wide range of operating conditions, which led to questioning this initial choice of grinding medium for the attrition-leaching process under mineral carbonation conditions. It is emphasised that the same approach could be applied to ores of greater economic significance.

Jan 1, 2016

By William Winsor, Harold L. Snyder

"AbstractShould oil and gas be proven in commercial quantities on the Labrador Shelf, current technology is not adequate for production operations in this severe environment, which includes yearly invasion of pack ice and icebergs. The fishery of this section of the North Atlantic is a vital resource to which a major oil spill or blow-out would impose an intolerable burden, This means that production systems must be designed and built to be fail-safe.The experiences of mining in Bell Island and Cape Breton have shown that it is possible to operate beneath the ocean floor, and this technology may hold the key for safe, reliable and economic production, This paper attempts to define particular problems and outline possible solutions.IntroductionOUR DISCUSSION is subject to the assumption that large hydrocarbon reservoirs will be discovered in the sedimentary basin of the Labrador continental margin. The petroleum industry has not attempted to operate in a harsher area. The Labrador coastline is exposed to North Atlantic storms and icebergs year’round, Arctic pack ice occurs up to six months of each year. However, there is no doubt that, if sufficient hydrocarbon potential is outlined, development will proceed."

Jan 1, 1977

By Oliver Hall

This paper sketches the mining at Noranda as it would be sketched to a visiting engineer. It does not follow quite the usual form, but is presented somewhat along the lines of a conversation. TO give the mining at Noranda its proper perspective, it is necessary to sketch the whole picture and outline: 1. History 2. Metallurgical Problems 3. Exploration 4. Mining Methods 5. Mining Details 6. Filling 7. Pillar Extraction 8. Costs HISTORY Noranda is a relatively young enterprise, with much of the personal character of its founders woven into it. The name Noranda is an abbreviation of Northern Canada and the name has been a happy one for an enterprise based on northern resources, tenacity and courage. The discovery credit goes to Ed. H. Horne. This intrepid prospector returned again and again to his sulphide discoveries on the shores of Osisko lake and, in 1922, after ten years of prospecting, succeeded in interesting S. C. Thomson and H. W. Chadbourne in his discoveries. The early exploration by L. K. Fletcher, from 1922 to 1925, for Thomson and Chadbourne, indicated promising, but somewhat perplexing, ore conditions. Mr. E. Hibbert and Mr. H. L. Roscoe rook on the task of preparing the mine for production and building a smelter in 1926, and this difficult task in this isolated area made steady progress and the smelter was blown-in in December, 1927.

Jan 1, 1937

By I-H. Jung, J. Kim, B. Konar

"The usage of FeNdB permanent magnet, containing Rare earth elements (REEs), is steeply increasing with its demand for wind-turbine and electrical vehicle. The improvement and recycling of the permanent magnet require good understanding of chemistry of all constituent elements. In order to understand the chemical interactions between REEs and Fe, all Fe-RE binary systems have been critically assessed and optimized based on reliable literature data. The Modified Quasichemical Model and Compound energy formalism is employed to model the liquid phase and the solid solutions present in the binary systems respectively. The enthalpy of the liquid and the intermetallic phases showed a systematic trend along the lanthanide series. This helped to mitigate the discrepancies in literature data and also to predict the binary interactions between some less well investigated Fe-RE binary systems. INTRODUCTIONRare Earth elements (REEs) are a group of seventeen elements (including Scandium, Yttrium and the lanthanide series) that exhibit same characteristic chemical and physical properties. These properties make them valuable to the electronic, appliance, green technology, weapon and medical device manufacturing industries. Compounds of REE with other metals (like Co, Fe, Ni etc.) have unique properties of luminescence, thermal and electrical conductivity, magnetism and ability to act as catalysts and polishing compounds (Gschneidner ,2011).They are not only indispensable for some electronic gadgets of today, like computers, music systems, mobile devices, televisions and MRI machines, but also holds a key to more greener technology of the future. They contribute to the development of more efficient and environment friendly version of everyday products such as cars and light bulbs. REE compounds revolutionized the magnet industry by making them smaller and more powerful with increased longevity, and high temperature workability, which are used in motors and generators that power electronics, telecommunications, electric automobiles and turbines(Humphries, 2011)."

Jan 1, 2012

By A. E. Flynn

Introduction The purpose of this paper is to record the results of researches on anhydrite that have been undertaken at the Nova Scotia Technical College during the last two or three years. The work was carried out in the Mining Department of the College, and several investigators were engaged on the work from time to time. Messrs. R. E. Hanson and K. M. Ed devoted their mining theses to the investigation, and Messrs. J. C. Hall and G. W. Baker were engaged on the work during the summers of 1928 and 1929, respectively. The writer was responsible for the initiation and direction of these researches, which were made possible by the financial assistance of the Department of Mines of the Province of Nova Scotia. Nova Scotia is the leading Province in Canada for gypsum production, its output being about a million tons per year, or over 80 percent of the production for the whole of Canada. The commanding position of Nova Scotia in this regard is due to the abundant supply of gypsum and its proximity to areas of intense utilization in the eastern United States. The resources of gypsum are contained in a total area of 627 square miles of gypsiferous rocks, so that an enormous reserve of this mineral is available. Present operations are confined to the highest grade and most easily worked deposits close to water transportation.

Jan 1, 1930

By G. H. Agnew

When water floods are initiated after gas-oil ratios have increased, the transition period from the start of injection until" the gas-oil ratios are returned to the solution gas-oil ratio may be important for either economic or technical reasons. The transition period is longest, and consequently most critical in water floods where injection is equal to withdrawals. This paper describes a theoretical basis for predicting the behavior of such a system and outlines a procedure for making the necessary calculations. The calculation procedure is illustrated for two actual cases: a line drive water flood and a five spot water flood. In each case there is a reasonable similarity between the actual and calculated performance.

Jan 1, 1960

By K. C. Marsden, B. Pesic

"Interest in the efficient production and recycling of rare earth elements has increased in recent years along with the prices of these elements. The molten LiCl-KCl eutectic is one ionic solvent which can be utilized for these purposes. The LiCl-KCl eutectic has also been selected as the electrolyte for focused research for advanced pyrochemical recycling processes for used nuclear fuel in several nations. Rare earth elements are fission products with notable neutron absorption characteristics, and thorough understanding of the properties and behavior of these elements is critical to their successful partition from the electrochemically-similar actinide elements. The number of research papers investigating individual rare earth elements has greatly expanded in the approximately 35 years since the last review. These research papers are presented in a variety of languages and technical formats, making data difficult to compare, and are sometimes contradictory. A review and summary of diffusion properties of rare earths in LiCl-KCl eutectic was performed, and the data translated to a common format for evaluation. INTRODUCTIONThe rare earth elements have experienced growing importance in recent decades due to their application in high technology, including optical lenses, lasers, high-temperature superconductors, improved alloys, high energy-density batteries, and powerful magnets for compact electronic devices. Their historic production methods and uses are detailed in several texts (Hampel 1971; Bautista &Jackson 1992; Gupta & Krishnamurthy 2005). A s the p rice o f these e lements has r isen in r ecent years, so has interest in their efficient production and possible recycling options. Rare earth oxides are concentrated through hydrometallurgical techniques, but the high thermochemical stability of their oxides precludes production of rare earth metals in aqueous systems. However, the wide electrochemical window and better control of pO2- in fused salt systems allows the production of these reactive metals from their halides or oxides. The high ionic conductivity and diffusivity of the molten ionic electrolyte allow high currents with limited resistive losses (Fray 1980). Electrolytic methods in fused salts are commonly adopted for the production of bulk rare earths in a variety of molten salt systems. Fluorides are sometimes proposed for oxide electrowinning processes due to ability to dissolve the rare earth oxide, reduced hygroscopic behavior, and the wider electrochemical separation between O2 and halide gas evolution (Mohan Das, Damodaran et al. 1988; Gibilaro, Pivato et al. 2011). However, in most electrolytic production processes, such as that for mischmetal, the rare earth oxides are converted to chloride prior to electrolysis in a chloride bath (Gschneidner Jr. & Eyring 1978; Sharma 1987). Of the chlorides, the LiCl-KCl eutectic is one specific medium in which metal production and production-related investigations have been conducted (Gschneidner J r. & Eyring 1978; Driscoll & Fray 1993). L iCl-KCl eutectic has the advantages o f h igh conductivity, but relatively low viscosity and operating temperature. The low operating temperature allows simpler design, with reduced energy consumption, salt volatility and cell corrosion."

Jan 1, 2012

By Duanyou Li, Qing Xiao, Zhiwang Wang, Xiaoqing Gan

"Seepage is a major cause of earth-rockfill dam failure. Numerical simulation of infiltration process, distribution of drift, flow velocity and direction after the impoundment can guide seepage control and evaluate its effects. A double field coupling model is established based on soil consolidation theory and the interaction between the seepage field and the temperature field. The simulation is implemented under the situation of core wall setted, core wall not setted, and core wall setted with concentrated leakage. The results indicated that the saturation line height was significantly reduced due to impervious core wall, and the temperature distribution is uniform above the saturation line. If concentrated leakage occurs, temperature distribution of dam was significantly changed, which is consistent with theoretical inference.INTRODUCTIONEngineering seepage field distribution must be calculated in seepage control design, optimization, and correction of new engineering construction of earth dams, as well as in seepage monitoring and evaluation of existing earth-rockfill dams. The aim of calculation is to identify the important parameters in seepage field, such as the coefficient of permeability, seepage flow, pressure, head, and allowable seepage slope, for effectively implementing seepage control design, correction, safety assessment, and anti-seepage reinforcement. These seepage parameters usually can be obtained by in-situ test and back-analysis based on reliable monitoring data.In order to obtain reliable monitoring data and reflect the earth-rockfill dam seepage state and change process, appropriate monitoring technology and monitoring method is necessary. The traditional seepage monitoring method is through site inspection and sensors (e.g., osmometer, piezometric tube and measuring weir) that buried in the structure and its foundation. However, there are still some disadvantages:"

Jan 1, 2015

By C. A. Hardie, G. F. Leichtle, J. A. Finch, J. A. Watson

"The recycling of wastepaper has become an important and common process worldwide. Techniques similar to those used in the mineral processing industry are used to produce high quality recycled fibres for use in newsprint. The mineral processing group at McGill University, in conjunction with the Pulp and Paper industry (Mechanical and Chemi-mechanical Wood Pulp Network), has adapted one of these techniques, column flotation, for the purpose of deinking wastepaper. This article describes the typical process of recycling wastepaper from a mineral processing point of view. It also presents results from McGill University’s flotation column test work at a Québec wastepaper recycling facility. IntroductionThe recycling of wastepaper has become an important and common process worldwide, including Canada which is now the world’s largest importer of wastepaper (CPPA, 1996). Much of the current drive to increase the utilization rate of recovered paper is a reaction to the solid-waste disposal problem that faces many Canadian and United States municipalities. The real problem in the disposal of solid waste is not the absolute amount of garbage that must be disposed of each year, but this amount in relation to available disposal capacity.Environmental restrictions on the creation of new landfill sites and incinerators (the two main options for disposal of municipal solid waste) have tightened the demand/supply balance in the solid waste disposal market. This shrinking availability of waste disposal sites in the face of increasing population with greater disposal requirements defines the Developed World’s solid waste crisis. Not only are there fewer disposal sites available, but the costs of using them is skyrocketing. These factors have increased government regulations mandating recycled paper content in newsprint. Conservation and environmental issues make the current drive for wastepaper recycling a real issue and business opportunity."

Jan 1, 1999

By R. Howard

"In projects involving resource development and plant optimization, the use of in-mine geophysics can deliver considerable benefit. The value proposition lies in using very high resolution downhole measurements to model process-plant outcomes. The calibration procedure used to convert in-situ physical properties into process engineering parameters is illustrated using two iron ore projects. Data correction was related either to orebody structure or mineral formation. The deliverable from this approach is a series of high-definition sections indicating the variability of ore delivered to a front-end separation plant and parameters for mine scheduling and stockpile design needed for maximum product yield.RÉSUMÉ Dans des projets de développement des ressources et d’optimisation de l’usine, l’utilisation de la géophysique minière peut engendrer des bénéfices considérables. La valeur de la proposition réside dans l’utilisation de diagraphies à très haute résolution afin de modéliser les résultats de l’usine de traitement. La procédure d’étalonnage utilisée pour convertir les propriétés physiques in situ en des paramètres d’ingénierie de procédés est illustrée en se basant sur deux projets de minerai de fer. La correction des données porte sur la structure de la masse minérale ou de la formation minérale. Les livrable attendus de cette approche sont une série de sections à haute définition, signalant la variabilité du minerai livré à une usine de séparation de première ligne, des paramètres pour l’échéancier de la mine et la conception des haldes requis pour une production optimale."

Jan 1, 2016

By L. Vu, V. Popov, J. Beland, R. Darling

"The Ferderber gold deposit is of Archean age. It consists of a series of gold-bearing quartz lenses within a shear zone that crosscuts the central part of the quartz dioritic Bourlamaque batholith. On average, this zone strikes N70E and dips 65SE. The Ferderber shear zone, which hosts the ore lenses, has been affected by a succession of tectonic events. A possible early period of brittle shear, accompanied by the formation of quartz lenses, resulted from strike slip movement along the zone. These early quartz veins were subsequently folded and boudinaged during reverse movement that accompanied a prolonged period of ductile shear. More quartz veins were emplaced in the shear zone at this time; these were also deformed by the thrusting. The latest tectonic event to affect the shear zone was a period of brittle fracture.Early dextral strike-slip movement on the shear zone is suggested by the local occurrence of Riedel shears, the preferred association of ore with east-northeast oriented segments of the zone, and by the apparent en echelon arrangement of some ore lenses. The most important event, a reverse movement, is indicatedby the attitudesoffoliation, folds, boudins, COS tectonites and slip planes. The late brittle fracturing formed narrow gouge filled faults, locally flanked by brecciazones, whichrun generally within and parallel to the shear zone, and also conjugate fractures that crosscut the zone.The Ferderber and six other adjacent gold deposits were formed in a structural regime dominated by a generally horizontal north-south regional compression. The Y axis of the strain ellipsoid is east-west and varies from horizontal to a plunge of 25 0 w."

Jan 1, 1987

By Hani S. Mitri

Strainbursts in brittle rock are common to deep underground mines. The state of stress at the boundary of mine openings is dictated by a biaxial stress/loading condition. This paper reports the results of a series of biaxial compression tests carried out on 100 mm cubic samples of norite rock, under different horizontal-to-vertical stress ratios. The results indicate that the biaxial compressive strength is considerably higher than the uniaxial one. It is found that the norite sample behaviour under biaxial loading mirrors field behaviour where shearing and progressive spalling of the opening boundary are observed prior to strainbursting. Sample failure is initiated by rock spalling at the sample free faces, i.e. in the plane of biaxial loading. Finally, it?s the out-of-plane shear failure mechanism that causes the sample to collapse. Shear failure takes place violently and abruptly and is accompanied with considerable audible noise.

Apr 1, 2005

By C. T. Harper, B. J. Fryer, R. P. Taylor

"IntroductionThe Maurice Bay deposit is one of a number of uranium deposits that have been found in recent years in the Athabasca Basin of northern Saskatchewan (Tremblay, 1982). This deposit, along with the others, belongs to the unconformity type deposits (Beck, 1977). They are, for the most part, polymetallic, being characterized by a suite of metals which include U, Ni, Co, Cu, Pb, Zn, Mn, V, Ag, Au, Pt-group elements, S, As, Bi, Se, Te, and Mo, some of which, besides U, are present in economic concentrations (Amok, 1974; Ruzicka, 1975; Tapaninen, 1976; Hoeve and Sibbald, 1978; Dahlkamp, 1978). The Maurice Bay deposit was known to be a small low grade deposit in which the ore was essentially monomineralic, consisting mainly of pitchblende (Harper, 1978). However, the occurrence of trace amounts of some of the elements common in the larger polymetallic ore bodies (e.g. Key Lake, Cluff Lake D) was anticipated. Thus a lithogeochemical sampling project was undertaken in 1979 across part of the Maurice Bay deposit (Harper, 1979). Major oxides (SiO2, Al2O3, FeO, Fe2O, MgO, CaO, K2O, Na2O, MnO, P2O5, and TiO2) and a group of the most common trace metals (U, Ni, Co, Cu, Pb, As, Au, V, and Se) were analyzed to determine whether any elemental patterns (halos or depletions) could be detected which would reduce the number of pathfinder elements needed for exploration purposes. In addition to the above metals, Th was also checked because some conglomerate strata in the Maurice Bay area are known to be thorium-enriched (Harper, 1978). Only the trace metal distributions will be discussed in detail in this report.General GeologyThe Maurice Bay area is underlain by three major groups of rocks, the White Lake metamorphic complex, an unnamed granodiorite complex, and the Athabasca Group, described previously (Fig. 1; Harper, 1979). Table 1 summarizes the stratigraphic features as deduced by geological mapping and the examination of drill cores."

Jan 1, 1986

By M. Abumiya, N. Onodera

"The synthesis of large scorodite particles in non-ferrous metallurgical industries usually requires a high-cost operation involving heating and high-pressure autoclaving. To overcome these obstacles, an atmospheric-pressure process for scorodite synthesis (DMSP®) was developed, in which ferrous ions were oxidized by oxygen gas in the presence of pentavalent arsenic ions. This process gives scorodite of good crystallinity with particle sizes as large as 15-20 µm. The solutions used for scorodite synthesis in the DMSP® are prepared from various residues containing arsenic from non-ferrous smelters. The solutions may be contaminated with Cu, Sb, and Bi, for example, and therefore the effects of such impurities on the formation of crystalline scorodite need to be investigated. In this study, the effects of Cu, Sb, and Bi contaminants on the formation behaviors of scorodite particles in the DMSP® were investigated systematically.INTRODUCTIONThe synthesis of crystalline scorodite (FeAsO4·2H2O) is a suitable method for arsenic (As) stabilization and storage of As-containing by-products such as flue gas dusts in non-ferrous smelters. It is expected that the formation of large, highly-crystalline scorodite particles would be an ideal method for avoiding the release of arsenic to the environment. Generally, autoclave methods under pressurized oxidation conditions at temperatures above 100°C have been used for the formation of arsenic minerals such as scorodite. However, the autoclave method requires sealed vessels that are resistant to high pressure, heat and acids. This process is also unfavorable on account of the high construction expenses, and high running costs as a result of vapor heat loss. Processes for synthesizing scorodite under atmospheric conditions at temperatures below 100°C which do not need an autoclave have therefore been extensively investigated (Demopoulos, Droppert, & VanWeert, 1994; Demopoulos, 1996; Demopoulos, Lagno, Wang, & Singhania, 2003; Droppert, Demopoulos, & Harris, 1996; Filippou & Demopoulos, 1997).Recently, Fujita et al. (Fujita, Taguchi, Abumiya, Matsumoto, Shibata, & Nakamura, 2008a, 2008b, 2009; Fujita, Taguchi, Kubo, Shibata, & Nakamura, 2009; Fujita, Taguchi, Shibata, & Nakamura, 2009) developed a new method for producing large scorodite crystalline particles with improved filtration and washability properties at normal atmospheric pressure and temperatures below 100°C. In the new method, oxygen gas (O2) is blown into solutions containing a high concentration of arsenic ions (As(V)) and ferrous ions (Fe(II)). The Fe(II) ions were subsequently oxidized to ferric ions (Fe(III)), resulting in the formation of large scorodite particles. High supersaturation of solutes such as Fe(III) will result in excessive nucleation, and the formation of poorly crystalline phases. The scorodite formation must therefore be conducted in a manner that avoids the critical supersaturation level being exceeded. It is supposed that the oxidation of Fe(II) to Fe(III) by O2 gas in the new method suppressed the supersaturation of Fe(III) during scorodite formation. The low Fe(III) supersaturation resulted in formations of highly crystalline scorodite particles of size of around 20 µm. In June 2008, based on the developed process described above, DOWA began experiments to verify the industrial capability of a plant with a capacity of 30 MT/month of As. It was successfully proven that it is possible to produce crystalline scorodite industrially on a commercial scale. This process was named and trademarked as DMSP® (Kubo, Abumiya, & Matsumoto, 2010)."

Jan 1, 2012

By E. B. Wilson

"Although the Operations Research technique of Reliability Theory has been applied with marked success in many fields, including the Apollo spaceship programs, the concept of reliability has not been generally adopted in mining and other heavy industries. Of course, reliability, or the probability that a system will be able to operate without a failure for a given interval of time, does not require the same emphasis in mining as in the aerospace industries. Nevertheless, certain aspects of Reliability Theory can be followed advantageously. For example, reliability calculations can determine the best time to overhaul and whether to retain stand-by units.The usefulness of the pseudo-operations research technique known as Replacement Theory is more readily re-cognized by the maintenance engineers in mining and other heavy industries. One of the least complex models enables the optimum Lifetime of an asset to be determined."

Jan 1, 1970

By J. C. White

"This paper was prepared for and presented at a lecture series on ""Materials Randling"" at McGill University. The development of trackless mining at Gaspe Copper Mines, Limited is described, showing the changes in mining method and the part played by the mobile equipment in the evolution of this highly mechanized underground operation. Comparisons of loading and hauling machines are given and an attempt is made to predict some possible future developments.INTRODUCTIONTHE PROPERTY OF GASPE COPPER MINES LIMITED is located in the Gaspe Peninsula of the Province of Quebec, 60 miles west of the village of Gaspe and 25 miles south of the St. Lawrence River. The original discovery of low-grade ore was made at Copper Mountain in 1921. Subsequent exploration revealed the richer Needle Mountain orebodies, and eventually in 1951 the decision was made by Noranda Mines to build the mining, concentrating and smelting complex (Figure 1). Construction and development of the mine was commenced in 1952 and production started in 1955."

Jan 1, 1968

By F. Vahdatikhaki

Simulation techniques have offered significant boosts toward a cost-and-time-optimized planning of construction projects by enabling project managers to effectively comprehend the behavior of projects. Using historic data from projects of like nature, simulation considers uncertainties involved in a project through accommodating the stochastic modeling parameters. However, the heavy reliance on the statistical data and not taking into account the context-specific features of the project cause the degradation in the realism and accuracy of the simulation models. Similarly, the extent to which a historic pattern could be retrofitted to new projects will decrease in line with the growing uniqueness of the projects and the novelty of construction methods. Furthermore, the existing real-time simulation frameworks are not capable of distinguishing the transient environmental changes, with minimal long-term impacts on the productivity, from the influential changes that will greatly impact an operation. In addition, existing simulation tools are devoid of location awareness, resulting in the inability to consider safety threats in their representation of the project. To address these issues, this research proposes a framework based on the integration of new tracking technologies used in Automated Machine Guidance (AMG) with simulation-driven 4D modeling methods. The proposed framework automates the adjustment of the simulation model based on the updated data from the site, and thus transforms simulation from a predictive tool used at the planning phase to a proactive monitoring platform usable throughout the planning and construction phases. A prototype is developed to test and demonstrate the effectiveness of the proposed approach.

Aug 1, 2013