Search Documents

By D. Kachongo, Y. Cheng, A. Kashala, D. Samal, G. Mitshabu

Many copper processing flowsheets in the Democratic Republic of Congo include the leaching of oxide ores containing copper and cobalt, copper solvent extraction, copper electrowinning, and precipitation of cobalt salt. Recently, cobalt price gained momentum, driven mostly by the fast-growing electric vehicles battery market. The ore blending scenarios tend to prioritise high cobalt grade ore, whatever the content of copper and other impurities. Therefore, many copper solvent extraction circuits are running below design capacity. The variability of feed induces a variability of the leach solution with respect to copper, manganese, and silica contents. It is thus important to adjust hydrodynamic and metallurgical parameters of the solvent extraction plant to optimise metallurgical performance, production cost, and the quality of the copper electrolyte. This paper presents some results on how solvent extraction plant parameters have been managed in two solvent extraction plants running with lower than designed copper input. INTRODUCTION Referring to a report of the chamber of commerce of the Democratic Republic of Congo (DRC) the online publication Agence Ecofin (2019) indicated that the DRC ranks in the fifth position of the world top copper producing countries with over 1.2 million tons produced in 2018. The same year, 66% of the world’s cobalt was produced in the DRC at over 106,000 tons. If the political situation remained stable and the new tax regime introduced in 2018 did not deter private investors, copper production could reach 1.4 million tons/a in 2020 as pointed out in Mining.com (2019). Forecast figures for DRC cobalt production vary widely depending on analysts. The DRC online magazine Actualité.cd (2018) referring to a ministerial source forecasts over 141,000 t cobalt/a for 2020. The reality will depend on many factors, including the selling price, the supply compared to the demand, and finally the reaction of investors to the new DRC tax regime. The growing electric vehicle batteries market has been the major key driver of the price of cobalt. The five years historical cobalt price graph in figure 1 from infomine.com (2019) shows that the price of cobalt peaked at over 40 USD/lb in the first quarter of 2018. Cited by the online Magazine Creamer Media, Smith (2019) has indicated that the long-term demand of cobalt will likely remain strong.

Jan 1, 2019

By T. Chong, R. Pesalj, B. Marchant, Z. Nikic

"The Mount Polley copper/gold project is located in central British Columbia and is currently being developed by Imperial Metals Corporation. Extensive laboratory and pilot plant testing was required to develop acceptable metallurgy for recovery of both sulphide and oxide copper-gold mineralization. Copper recovery is highly sensitive to oxide copper content of the feed whereas gold is primarily associated with the copper sulphide minerals. A conventional flowsheet where sulphide flotation is followed by sulphidization and oxide scavenging is described. The conventional flowsheet was used in a feasibility study which resulted in a favourable production decision at Mount Polley. Detailed engineering and permitting are in progress.More recently, laboratory and pilot testing of a new flotation reagent, S-6493*, an oxide specific collector, has indicated that improved copper recovery can be accomplished with reduced reagent consumption, including elimination of the sulphidization step, using S-6493 compared with the conventional flowsheet. The comparative metallurgical results using S-6493 and conventional sulphidization methods are presented, from both bench scale and pilot testing. Comparative economics of the conventional flowsheet and that using S-6493 are also presented. Advantages of S-6493 include reduced reagent costs, increased revenues from additional copper recovery, and overall reduction in capital and plant operating costs due to the simplified flowsheet. INTRODUCDONThe Mount Polley copper/gold property is located in Central British Columbia, 56 air kilometres northeast of Williams Lake. The first recorded exploration was in 1964. By 1989, a total of 238 diamond drill holes, totalling 27, 522 meters, was completed to detail reserves on the Mount Polley prospect. A number of drill core composites were submitted, containing a variety of oxide copper levels, for metallurgical flowsheet development. Six bulk samples were collected from surface trenches for additional bench scale testing and for pilot plant testing."

Jan 1, 1991

By H. A. Bilgin, G. G. U. Aldas

"Ground vibration is the natural result of the blasting process. Many empirical formulae and methodologies including analysis of travel path effects have been developed. The scaled distance, which is the most popular approach for the calculation of the attenuation of particle velocity in the ground, has led to significant advances in the prediction of particle velocity when both explosive charge and distance vary. However, this approach does not consider the effect of ground anisotropy and existence of structural geological features on ground vibration. Therefore, in this study, the effects of these rock mass properties on types, amplitudes, and frequencies of ground vibration waves at four surface mines are examined. The results, which were implemented at Kangal coal mine, Bastas quarry and Kíbrís quarry, provided guidance for the extensive study at Orhaneli surface coal mine.As a result of the study, the authors came to the conclusion that vibration amplitudes change depending on the ground on which sensors were deployed and the conditions depending on whether measurements were done near major structural geological features. It was determined that the vibration amplitudes, measured at equal distances from the source but in different directions, change because of the propagation velocity anisotropy. Besides the change of wave type due to the kind of ground at the measurement location, it was determined that vibration anomolies were due to structural features."

Jan 1, 2004

This paper presents a case study where Cenozoic age detritals and an ancient buried landslide have been modelled in the final walls of an iron ore pit. Orebody 25 is located in Western Australia’s Pilbara region and is an operating pit where a redesign of the final wall cutback was required. The existing slope design utilised a simplistic geological model of mixed conglomeratic, calcretic and clay –dominated detritals overlying deformed bedrock sequences. This simplicity resulted in a conservative design that was not reflective of the slopes performance to that point. Further field investigation was carried out with the results assessed in conjunction with historic drilling, mapping and laboratory testing. A detailed geotechnical model was developed including three conglomerate and two clay dominated units and laterstage calcrete overprinting. The clay units were of significant importance to the stability assessment and resulting slope design due to the thickness and poor strength conditions indicated by the laboratory and field testing. However, the drilling investigation shed only limited understanding as to the origin of the clays and thereby how they should be treated as a component in the stability analysis. A comparison of the ratio of various geochemical elements measured by assay was made between the clays and 1) shale bedrock and 2) clays of known detrital origin from other nearby sites. This indicated the clays had a strong affinity with weathered bedrock. This and other textural features resulted in the interpretation that the clay units were relic debris preserved following ancient landslides in bedrock shale. Using laboratory testing data and calibration of results for a landslide origin, stability analyses were run, resulting in a steeper slope design being implemented. Excavation of the final cutback is now in progress with the model confirmed as appropriate.

Jan 1, 2015

By R. F. Hochstein, A. J. Neale, B. C. Flintoff

"Process control technology holds very significant potential benefits for many mineral and coal processing plants. The impact can be expected in terms of performance improvements (e.g. increased throughput, better quality control, higher availability), through reduced operating costs (e.g. lower reagent consumptions, manpower reductions) and in the form of intangibles (e.g. reduced vulnerability to manpower turnover, increased productivity in the user group). However, the installation of a process control system will represent considerable capital expenditure and will generate an operating cost. No management team would approve the funding for such a project without some reasonable measure(s) of the profitability of a proposed system. This paper describes a methodology for addressing the justification problem. Of particular interest is the approach to quantifying performance improvements, frequently found to be the predominant benefit of process control.INTROPUCTIONProcess control has become widely recognized as an essential component of any processing operation. It has direct impact on productivity, process efficiency and product marketability. The reported pay backs associated with successful installations underscore this observation. As a consequence, many operators who have little in the way of process automation are looking to initiate control projects, while those who currently enjoy some level of automation are looking to upgrade existing control systems (= process + instrumentation + hardware + software + operators + support). While the emphasis here would appear to be on retrofit process control projects, new plants, or those currently in the design stage, will usually find themselves in one of these categories shortly after startup 1."

Jan 1, 1990

By Fabien Miller

Automation technologies are increasingly envisaged to improve underground mining productivity. However, the technologies need to be used and adopted gradually in order to get the best benefits. This paper presents the technical and operational aspects of autoguided production vehicles at Brunswick Mine. During 2001 Noranda?s Brunswick Mine has successfully commissioned an automated haulage zone where two optically guided trucks transport ore from a remotely operated chute to two orepasses. Operational advantages include increased system capacity and enhanced safety and comfort for the operator. The data obtained up to now indicate that the system can operate reliably in mine production

May 1, 2002

By M. W. Lewis

A mine's inherent capacity is dictated by factors such as equipment, design, people, processes, and environment. Actual production may approach, but never surpass, the inherent capacity limit. The inherent capacity ceiling can only be increased through re-engineering. Autonomous haulage systems have the potential to significantly increase a mine ’s inherent and realized capacity. Realized capacity may be maximized through the optimization of soft factors such as the processes, behaviours, and organizational systems, controlling asset utilization, availability, and performance. Truck shovel dispatching systems revolutionized the utilization of mobile assets. High-precision global positioning systems (HP-GPS) are increasingly being adopted to optimize equipment performance. Real-time maintenance management systems have the potential to revolutionize equipment availability and significantly reduce cash costs. This paper explores some of the solutions available to mines to increase their inherent capacity and maximize their realized capacity.

Jan 1, 2004

By M. W. Lewis, B. Sambirsky, J. Werner

A mine’s inherent capacity is dictated by factors such as equipment, design, people, processes, and environment. Actual production may approach, but never surpass, the inherent capacity limit. The inherent capacity ceiling can only be increased through re-engineering. Autonomous haulage systems have the potential to significantly increase a mine’s inherent and realized capacity. Realized capacity may be maximized through the optimization of soft factors such as the processes, behaviours, and organizational systems, controlling asset utilization, availability, and performance. Truck shovel dispatching systems revolutionized the utilization of mobile assets. High-precision global positioning systems (HP-GPS) are increasingly being adopted to optimize equipment performance. Real-time maintenance management systems have the potential to revolutionize equipment availability and significantly reduce cash costs. This paper explores some of the solutions available to mines to increase their inherent capacity and maximize their realized capacity.

Jan 1, 2004

"WELCOME/BIENVENUE TO THE COM 2014 IN BEAUTIFUL VANCOUVER!On behalf of the organizing committee, I would like to extend my thanks to you for participating in this year’s Conference of Metallurgists. Recent times have been extremely difficult for the resource sector, but it is crucial for our industry to maintain personal connections through good and bad times. These interactions include technical exchanges, and this is at the heart of MetSoc’s service to its members. The theme of this 53rd Conference of Metallurgists is Prosperity Through Process Advancements. There are thirteen symposia at this year’s conference mainly focused on processing from extractive fields, to materials and the environment. Supporting these topics are the plenary, poster session, and trade show plus opportunities for socializing at functions like the opening reception and the awards banquet.Many people have contributed to this conference, from the authors and presenters to the organizers and the generous sponsors. They are all gratefully acknowledged for their quality work over the last two years. A particular thank you to our student volunteers whom we hope will take advantage of their time at COM to network and to learn about this exciting industry.Again, thank you for being a part of this exciting conference of metallurgists. I hope it will be a memorable experience and that you are able to take advantage of all the conference and Vancouver have to offer."

Jan 1, 2014

By S. Onuki, T. Ando, M. Tejima, R. Enomoto, Y. Okada

"Al–Si–Cu–Mg die casting alloys are widely used in the automotive industry, and recent advancements in high pressure die casting technology enable heat treating products to achieve desirable properties. However, CO2emissions associated with die-casting production lines should be reduced to address the global warming issue. In this study, the relation between the microstructures and thermal stability of precipitates formed during isothermal aging at 423, 485, and 558 K of Al-11.0 mass%Si-1.8 mass%Cu-0.2 mass% Mg (JIS ADC12) was investigated using Vickers hardness tests and transmission electron microscopy (TEM). The hardness tests and TEM results showed that Si compounds and Al–Cu compounds enhanced the mechanical properties of the alloy and that the predominant compound affecting the mechanical properties differed between specimens treated at 423 K and those treated at 558 K. Moreover, additional aging at 423–458 K resulted in a material with a Vickers hardness higher than that of the isothermally single-aged material. Differential scanning calorimetry, differential elemental analysis, and selected-area diffraction analysis using TEM suggested that the combination of Al–Cu compounds precipitated at low aging temperatures and Si compounds precipitated during preliminary aging increased the mechanical strength, resulting in a maximum hardness of 130 HV.INTRODUCTIONAl–Si–Cu–Mg die casting alloys have well-balanced mechanical properties, machinability, and cast ability. These alloys are therefore widely used in the automotive industry because of their superior characteristics, accounting for>90% of the aluminum used in die casting production. As a substitute for iron-based materials, these alloys have contributed to the development of lightweight vehicles.Dong et al. (2014) reported that the heat treatment of die casting materials is effective for changing their dimensions under high temperatures as a result of the precipitation of solid-solution elements. Recent advancements in high pressure die casting technology have led to the application of heat treatments of Al–Si–Cu–Mg alloy products to reduce fuel consumption and satisfy customer needs. Although attempts to reduce CO2emissions have focused on fuel consumption in cars and fuel efficiency regulations have become increasingly strict in recent years, CO2discharged from production lines should also be reduced without adversely affecting the properties of the product. Heat treatments for artificial aging after solution treatment (T6 treatment) and after casting (T5 treatment) are CO2discharge sources, which together with a holding furnace account for >80 % of the CO2discharged during the casting process."

Jan 1, 2018

By G. C. Baker

Despite the attention belatedly bestowed on tidal power in recent years, it remains largely a potential rather than an actual source of energy. The resource is, practically speaking, non-depletable. Extraction is technically feasible and environmentally acceptable. The restraints against development are economic, and they could be removed by technical improvements, changes in the cost or availability of other energy sources, or simply by a change in the cost of money. The exponential rise in the demand for energy makes it inevitable that the tides will be harnessed sooner or later.

Jan 1, 1972

By Janis A. Shandro

The mining sector is a major economic driver for Canadian, and British Columbian communities. In parallel strong commitments have been made by industry to the well-being and sustainability of associated communities. However, these dimensions are the least understood. Especially lacking are focused regional investigations that compare the well-being and sustainability of communities dependent on different resources sectors. It is hypothesized that this type of comparative analysis will help to foster a greater understanding of what makes a resource or mining community healthy and sustainable. This paper describes research that examined community-level indicators associated with well-being (e.g. education, income and employment) and sustainability (e.g. economic diversity). The indicators were derived from Canadian Census data for 31 British Columbia resource-based communities (with a focus on mining) during a period of time (1991 to 2001) when resource sectors experienced an economic downturn. Our findings identify that during this decade, mining communities differed significantly from other resource-based communities, and comparative analysis of census derived indictors illuminate challenges that mining communities in British Columbia face with respect to wellbeing and sustainability (such as economic diversity, unemployment, and population loss). To contribute to the mining sector?s efforts towards meeting their commitments to communities, this paper concludes by proposing strategic opportunities aimed at the enhancement of mining community sustainability for policy-makers, communities, and the mining industry to consider.

May 1, 2011

By Stephanie Price

Engineering Associations ?Regulatory authority ?License individuals and firms ?Discipline licensed members ?Enforce against improper acts ?Programs for EIT?s, competence, etc

Oct 1, 2010

"Option pricing is used in finance for valuing options to buy (or sell) shares at some future date because it provides a convenient framework for quantifying values subject to uncertainty. As one of the main sources of uncertainty in mining is the price (sales) of the metal, this approach can also be used for valuing mining projects.The first part of this paper reviews options and option pricing; the second part presents the approach developed by Brennan and Schwartz (1985) for using option pricing to value natural resources. Several applications of this methodology have been published; these are described. From a mining point of view, the assumptions made by Brennan and Schwartz are too simplistic. The weaknesses are discussed with a view to improving an apparently promising new way of assessing the value of projects. IntroductionThe collapse of the British merchant banking group, Barings, has highlighted the risks that can be incurred by speculators and arbitragers in the futures and options markets. But this negative attention on futures and options should not make us forget their positive aspects. They can provide producers and consumers of metals with more predictable sales prices. The introduction of the new traded average price options, TAPOS, by the London Metal Exchange in January 1997 is a response to this need. Equally important, the theory that the finance industry has developed for valuing options provides an interesting framework for valuing mineral projects as well. While this paper was being revised, the South African gold mining house, JCI, announced that it was using a methodology based on option pricing for valuing the mineral rights to deeplevel gold resources (see Box 1)."

Jan 1, 1997

By David K. Fountain

"The growth of the mining industry in British Columbia in the last ten years has been largely the result of the development of large low-grade copper and molybdenum deposits. There are two problems which must be solved in the search for mineral deposits of this type. It is necessary to detect large volumes of rock containing a low percentage of total sulphide mineralization1 and, secondly, to get some idea of the economic significance of this mineralization. The standard geophysical exploration techniques available have a varying degree of application in the search for disseminated sulphide de-posits. The electrical methods, and the induced polarization method in particular, are the most successful direct methods, and magnetic methods have indirect application in most situations. This is illustrated by geo-physical survey results from several properties in British Columbia."

Jan 1, 1968

By D. Yamada, T. Tanaka, N. Inouchi, J. Nakahigashi, H. Yoshimura, T. Nonishi

The use of cereal food materials as lubricants was investigated in an attempt to develop nonpolluting lubricants. Suspensions of wheat flour in water and other types of cereal food lubricants were prepared and their friction coefficients measured. The results indicate that a cereal food lubricant containing 30% lipids, 2% proteins, 60% carbohydrates and 0.6% calcium carbonates has the lowest friction coefficient for a sheet (cpTi-1). As example applications, the lubricant was tested with a forming press and a screw-fastening device. In both applications the cereal food lubricant performed relatively well in comparison to conventional lubricants and thereby has potential for practical applications.

Jan 1, 2006

By O. A. Ojo, R. G. Ding, M. C. Chaturvedi

In this study, the fusion zone microstructure of tungsten inert gas weld of a directionally solidified NhAl-base alloy was examined by the standard metallographic techniques involving the use of optical, analytical scanning and transmission electron microscopes equipped with energy dispersive spectrometer. Fusion zone cracking was observed to be closely associated with interdendritic secondary solidification microconstituents identified as consisting of y, y' and NiMo (Y) phases. Depression of solidification temperature to the terminal ternary eutectic reaction temperature of the system during cooling is suggested as an important factor contributing to the fusion zone cracking.

Jan 1, 2006

By H. G. Rushton, A. S. Romaniuk

"The opening chapter of this volume, by A. Ignatieff, places in perspective Canada's coal resource base as part of the world scene. This chapter will focus on the Canadian scene.Units of measurement in this report are in the International System of Units (SI) as approved for official use by the Canadian Standards Association and Metric Commission Canada. These units have been adopted by the Mining Association of Canada and the Coal Association of Canada. To assist with the shift to metric units these two associations have published ""Metric Practice Guide for the Canadian Mining and Metallurgical Industries"", 1978(1J, Appendix ""A"" lists some useful conversion factors along with SI prefixes. The last official assessment of Canada's coal resources and reserves was done by the Department of Energy, Mines and Resources and presented in Report ER 79-9 ""Coal Resources and Reserves of Canada"", published in December 1979 and authored by H.U. Bielenstein, L.P. Chrismas, B.A. Latour and T.E. Tibbetts(2). The Geological Survey of Canada has a continuing project concerned with coal resource assessment as does CANMET, whose concern is with coal reserve assessment and coal quality. As well, Alberta's Energy Resources Conservation Board (ERCB) has a continuing assessment program for coal in Alberta and publishes an annual reserves report, the current issue of which is cited as reference No. (3). The difference in resource and reserve terminology as used by EMR and ERCB has a major effect on derived tonnages for Alberta. This difference will be discussed later. In 1982 the Department of Energy, Mines and Resources produced a map titled ""Canada-Coal""<4J which outlines coalfields and illustrates coal import and export movements for the years 1981and1980. A copy of this map is contained in the map pocket of this publication. Two other resource assessment reports are noteworthy, the first is ""Coal Resources of Southern Saskatchewan: A Model for Evaluation Methodology"", by J.A. Irvine, S.H. Whitaker and P.L. Broughton<SJ which is one of the major outputs of a joint federal-government study of southern Saskatchewan's lignite deposits. (Another output from this same study' is the Geological Survey of Canada's SASCO file, a computer processable file holding borehole and coal quality data.) The second is ""Deep Coal Resources of the Interior Plains, Estimated from Petroleum Borehole Data"", by G.D. Williams and M.C. Murphy(6) which identifies coal resources from nearly 4,000 petroleum exploration boreholes distributed uniformly over an area spanning Manitoba, Saskatchewan, Alberta and British Columbia."

Jan 1, 1985

By D. J. Hutchinson, M. Lato, M. Diederichs

Light Detection and Ranging (LiDAR)-based applications for geomechanical purposes have recently proven to be a highly reliable and accurate form of remote analysis and documentation. The ability to remotely collect, process and evaluate rockmasses for structural geomechanical applications has benefits ranging from safety to efficiency, and provides a permanent record that can be assessed before and after an excavation has been completed. With the collaboration of Queen’s University and Rio Tinto, the Iron Ore Company of Canada (IOC) mines in Labrador City, Newfoundland and Labrador, evaluated the practical application of the I-Site 4400 LiDAR equipment, in conjunction with the Vulcan geotechnical module for geomechanical purposes. The project provided a comparative analysis between conventional hand-mapping and digital analysis. The analysis indicates that digital mapping could be employed as an active tool within the general geotechnical workflow, where results would be used in pit wall and rockmass support designs. As well, the field work enabled the generation of effective operational guidelines and protocols to maximize scanning efficiency.

Jan 1, 2009

By A. G. Spencer

"The horsepower required to drive large grinding mills has increased dramatically during the past ten years. Limitations on the amount of power which may be transmitted by a single gear and pinion have resulted in the application of multimotor drives, with consequent loadsharing problems. It has also sparked the development of some entirely new drive concepts. In addition, the severe demands made upon the electrical system during the acceleration period have required that the selection of motors and electrical system design be closely coordinated. Moreover, the installation of such large process units results in downtime being very costly. The equipment selected and the plant maintenance philosophy must therefore be such as to minimize the risk of unscheduled downtime."

Jan 1, 1972