Search Documents

By Pound J. R

THIS mine, which is the property of the S. and M. Syndicate, London, is located at Moina, in North-West Tasmania, 18 miles from Stavertorr railway station and 36 miles from Devonport. There are metalled roads from both of these places, and, althoughhilly, these are good for team or motor traffic. Mails and passengers are provided for by a tri-weekly coach service from Sheffield, a railway town, distant 23 miles. The Moina mining field is situated on a main spur between the Forth and Iris Rivers, andat an elevation ranging from about 500 ft. above sea-level at the Forth River to 2400 ft. at the All Nations mine. The elevation at the mine office of the S. and M. mine is 1900 ft. The average annual rainfall, as recorded for the past eight years, is. 68 in.This inclildes, however, a couple of years during which the rainfall was much above normal, and taken over a longer period 60 in. would be nearer the average.

Jan 1, 1919

By Prasad S, Chatterjee S. S, Singh B. N

The chief source of metallic iron for steelmaking in India, even today, as it is in most part of the world, is through blast furnace (BF) route. This will continue to be so in the foreseeable future as the technology is most efficient, both process and economy-wise. However, as the world is moving into the next millennium, a critical look is being given to the process primarily because of its non-ecofriendliness (as a result of extensive use of metallurgical coal/coke requiring elaborate pollution control facilities) and huge investment involved for supporting facilities like extensive raw material preparation and handling, agglomeration, adoption of sophisticated instrumentation and control system, etc.

Jan 1, 1999

By Linge HG, Fernandez PG, Hughes HC

Aqueous oxidation is a possible alternative to roasting for the processing of gold bearing arsenopyrite (FeAsS) concentrates. The reaction has been studied by voltammetry and this has shown, for the first time, that FeAsS can be readily dissolved without passivation at room temperature in dilute sulphuric acid at relatively modest oxidation potentials (0.7 V SHE). The reaction forms sulphur on the mineral surface and the oxidant consumption is thus minimal. Two practical modes of slurry oxidation are listed.

Jan 1, 1989

By M J. Daniel

Mineral resources all over the world are often heterogeneous and have variable ore properties and ore grade. As a result the ore processed in concentrating plants varies over the life of mines. Consequently the circuits often suffer from bottlenecks typically at the stages of crushing, semi-autogeneous (SAG) and ball milling. Bottlenecks may be remedied with equipment retrofits, however, design engineers should consider a phased approach to the circuit design that delays initial capital expenditure over the life-of-mine. This paper deals with the debottlenecking of existing mineral processing plants by means of high pressure grinding roll (HPGR) applications. It also deals with the use of innovative flow sheet designs using HPGRs for the design of Greenfield plants by engineering or mining companies. In the case of Greenfield plant design an analysis with respect to energy efficiency and operating cost (OPEX) is presented. The analysis compares the performance of SAG based circuits against HPGR circuits that may be influenced by variable ore properties. Globally about 600 HPGRs are installed in various applications in the cement and minerals industries. In excess of 100 of these HPGRs are used since the mid 1980s for crushing and grinding of various ore types including æhard rockÆ applications. HPGR technology is mature enough to be considered as an ideal debottlenecking device. HPGRÆs are versatile, they have a low installation footprint and they are flexible in its machine settings (pressure, roll speed), which can be adjusted to react to ore variations whilst maintaining a high throughput. Examples for the benefits of using HPGR in terms of energy efficiency and operating costs are presented by this paper. æEco-efficientÆ flow sheets and sustainable development initiatives are linked to energy savings as an æenergy costÆ and benefit to the environment. Energy savingsÆ can also be analysed in terms of the ædollar costÆ (OPEX) savings. This paper demonstrates that HPGR is more energy efficient and may reduce the overall grinding energy requirements in the order of 16 per cent depending on the target grind size and ore properties. The HPGR is more cost efficient and may reduce overall grinding costs by as much as 19.3 per cent depending on the cost of energy, grinding media and the rate of grinding media wear in the comminution circuit.

Jan 1, 2009

Industrial minerals and rocks are those which are economically important because of desirable physical and/or chemical properties rather than metal or energy content. The evaluation of these resources for investment purposes in general follows established procedures after due consideration of well documented input data. However, in view of the sensitivity of many industrial mineral projects to specific inputs they require very careful analysis. The characteristics of the industrial minerals and the industrial minerals industry are reviewed and the significance of logistics, customer requirements, technology and marketing are discussed. Implications in relation to resources/reserves terminology are considered with phosphate rock used as an example. It is concluded that industrial mineral projects as a consequence of technology and market dependence in particular can give a high level of investment risk. The industry, however, offers most interesting and challenging employment opportunities for geologists, mineral engineers and economists.

Jan 1, 1988

By E J. Hofmann, J E. Hofmann, A J. Hofmann-Fritz

"With its Head Quarters in Perth, global heavy engineering company Hofmann Engineering is one of the largest family owned engineering companies in Australia. The company has pioneered a number of new manufacturing processes and design improvements for components of large comminution equipment.Some of these innovations are: Innovative design improvements of high pressure grinding roll (HPGR) forged steel tyres. Hofmann Engineering has developed unique patented tungsten carbide stud and edge protection designs which improve wear life and introduce quick and cost effective replacement options to further extend the life of the tyre. Development of forged fabricated mill heads using rolled and welded high tensile steel plate as an alternative to cast conical mill heads. Establishment of Australian capability to manufacture and export up to 42 ft. (12.8 m) diameter SAG mill shells. Techniques for fast track, product improved replacements of cracked or damaged mill gears, including in situ profile & wear measurements of girth gears using portable coordinate measuring machine (CMM) technology, forged rim steel and induction hardening technology. Gear and pinion mechanical drive designs to 24 MW or higher for SAG mills of 38 ft. to 42 ft. (11.6 m - 12.8 m) diameter as reliable alternatives to gearless drives.The paper presents case studies from the Australian heavy manufacturing facilities of Hofmann Engineering on large, high powered equipment for both the domestic and export markets.CITATION:Hofmann, E J, Hofmann, J E and Hofmann-Fritz, A J, 2013. Australian innovations in high pressure grinding rolls and large grinding mill manufacture, in Proceedings MetPlant 2013, pp 141-151 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

A detailed study of the capital investment and production cost for copper electrowinning plants shows that significant savings in both can be achieved by increasing the current density. From the economic analysis it is determined that the optimum current density which will result in lowest capital investment and lowest operating cost is between 60 A/sq. ft. and 70 A/sq. ft., or at least three times as high as the Conventionally employed current density. The specific investment, expressed as $/ton-year, is found to be a function of both the current density and plant capacity and has a minimum value at the optimum current density. Empirical equations are developed for the purpose of estimating the capital investment and operating cost for plants of any production capacity operating at any current density.

Jan 1, 1972

By Lamont G

The significance of blasthole stemming in determining blasting efficiency has been extensively studied for small diameter holes using gelignite explosives. Recent developments in blasting technology with the use of large diameter holes and low cost blasting agents have not included studies of the effectiveness of different types of stemming materials. A review of previous measurement techniques and the relevance of these earlier results to present stemming practice is presented in this paper. A survey of operating mines in Australia provided information for this analysis. The value of stemming in reducing blast noise and improving blasting efficiency is generally accepted but the use of bulk-loaded explosives in underground operations has resulted in the practice of eliminating the use of stemming material.In surface operations drill cuttings are used for stemming on the basis of availability rather than efficiency in providing resistance to movement. The development of laboratory testing techniques, based on noise level and borehole pressure measurements, to evaluate the relative efficiency of different types of stemming materials is described. The results of an extensive series of tests with ANFO explosive showed similar trends tothose obtained from earlier published results with gelignite type explosives. Conclusive quantitative results on the relative effectiveness of different stemming materials will require minor modifications to the existingequipment. Observations and the results of pressure measurements indicated the presence of shock wave effects which caused the ejection of the top section of the stemming column when using coarsely fragmented material.

Jan 1, 1979

By McDonald G. G

In the deformation of a metal or a single-phase alloy all the crystals composing the metal after their shape in a similar manner as the metal in bulk and to about· the same extent. This is not the case in an alloy consisting of two phases of different resistance to plastic deformation. In such an alloy the two phases take part in the deformation approximately in inverse proportion to their hardness, at least at the beginning of the deformation. (1) The hardness difference becomes less in the course of the deformation and thereby the deformation more equal. The phenomena occurring during cold-rolling of some two-phase alloys have been investigated by H. Unckel who made statistical grain measurements of the degree of deformation of the two phases after various reductions by rolling and also microscopical observations of the flow in the neighbourhood of the grain boundaries. Because of the different relative flow of the two phases, the normal flow is disturbed in the vicinity of their boundaries, and some additional plastic flow must take place in these regions, the disturbance being levelled out at some distance from the boundary. The deformation of the two phases present simultaneously in the material should thus be different from that of each phase separately. The investigation of theimportance and the effects of this interaction of crystals of different phases is the subject of this paper.The deformation of crystals occurs as a gliding of crystal layers following crystallographic laws. In consequence of this slip the crystals composing the material tend to assume a common orientation, i.e. some crystallographic axes tend to become parallel to each other in all the crystals. The type of this preferred orientation depends on the type of the crystal and the working process. Any change in the mechanism of deformation results, therefore, in a change in the preferred orientation. Such a change in kind and degree of preferred orientation will, therefore, also occur if the interaction of crystals in a two-phase alloy gives rise to a mechanism of deformation different from that in the free phases.The present paper describes a study of the preferred orientation, the microstructure and hardness in wires of brass drawn to various extents.The development of preferred orientations in the two phases with increasing reduction was followed up in various layers of the wire.EXPERIMENTAL DETAILSThe experiments were carried out with a commercial 5 S.W.G. wire (0,212 in. diameter) containing: 62·7% Cu, 37·3% Zn, very faint traces...

Jan 1, 1941

By Mikula PA

This paper presents the results of in-situ and laboratory investigations into a mining method which utilises conventional continuous mining techniques to carry out two passes in thick coal seams, resulting in the development of stable pillars with relatively small width dimensions and heights up to 6 m. Geotechnical investigations included structural mapping, brightness logging and standard laboratory testing. Virgin stress was measured using overcoring techniques. Two approaches to pillar design were used in the study. These were; pillar design based on empirical formulae and laboratory testing, and pillar disign using calibrated mathematical models. A trial panel was developed at 300 m depth to study pillar deformation and stress changes due to mining. The extent of rib deformation was studied using borescopes and extensometers. In-situ geotechnical measurements were used to calibrate displacement discontinuity and finite element mathematical models of the coal seam. These models were then used to predict the behaviour of a small panel of pillars which were to be developed to 6 m height. The mining method was shown to be feasible provided adequate rib support was installed. The benefit of rib support was found to be two-fold, in that it increased confinement of the pillar in zones of low horizontal stress, while reducing horizontal stress relaxation in zones of high horizontal virgin stress. The possiblity of roof control by designing the small pillars to yield on retreat is discussed.

Jan 1, 1986

The area between Merrygoen and Digilah is located on a structural high that separates the Sydney Basin from the Great Artesian Basin, and hence the stratigraphic succession of younger rocks overlying the basement is relatively thin. The stratigraphy is briefly described and it is shown that fluvial sedimentation prevailed from Upper Permian through to Middle Jurassic times. Flint clays occur in the Permian, Triassic and Jurassic but only those in the Jurassic appear to have commercial value at present. The chemical, mineralogical, and physical properties of the flint clays are discussed.

Jan 1, 1973

This investigation was planned to determine:1. The precipitation-hardening properties of the copper-nickel-phosphorus alloys; and2. The influence of arsenic and bismuth, singly and together, on the mechanical properties of these alloys.It was carried out in conjunction with an investigation, previously published in these Prooeedings on "The Influence of Various Elements on the Mechanical Properties of Copper containing a small percentage of Bismuth," and also formed part of a study of the influence of bismuth, nickel and phosphorus on the properties of commercial arsenical-copper.The first part of the present investigation arose out of a discovery some years ago of precipitation-hardening in phosphorus-deoxidized coppernickel boiler tubes, containing approximately 2% nickel and 0·03% phosphorus, supplied to an Australian Railways Department. At that time there was little information available on precipitation-hardening in copperrich copper-nickel-phosphorus alloys, but at the end of 1935 a short paper on the subject was published by E. C. Rollason and T. G. Bamford(2) and at the beginning of 1940 a comprehensive account was published by D. K. Crampton, H. L. Burghoff and J. T. Stacy.(3) Although the investigation carried, out independently by the present author was not as comprehensive as that of Crampton, Burghoff and Stacy, the results are in agreement with those of the American as well as of the British authors; hence, only a summary of this aspect of the work is needed here to establish a basis for a study of the influence of bismuth and arsenic.PREPARATION OF TEST PIECESAll alloys were melted under charcoal in plumbago crucibles in an oil-fired furnace and were poured out of contact with air into oil-dressed moulds to give billets either 7· 5 in. long X 0.83 in. diam. X 1·3 lb. weight or 12 in. long X 1·125 in. diam. X 3·3 lb. weight depending on requirements (the larger size was used, for example, in establishing the annealing characteristics of the precipitation-hardening alloys). The raw materials were electrolytic copper of the composition described in the previous paper(I) 6% copper-arsenic, 14% copper-phosphorus, 1:7% copper-bismuth, and Mond nickel in the form of "shot." The method of producing test pieces from these billets and the annealing treatments ana tests to which the pieces were subjected have been described in the previous paper.

Jan 1, 1944

By C Garrido, J Barrera, H Alvarez, L Perez, S Ramirez

In recent years, there has had a greater recurrence of studies and projects that consider tailings filtration followed by dry stacking to reduce the consumption of fresh water, the space required for disposal, and, eventually, to reduce the costs of the project. In addition, this technique could be required to meet new environmental restrictions to extend the life-of-mine of existing plants or to enable the development of new projects, especially in areas of high social interest. This article is intended to describe the most relevant technical aspects of the design and implementation of an iron ore tailings filtering system and its final overland disposal as well as physical and metallurgical surveys, and laboratory and pilot testing. Furthermore, it is presented how these activities are inserted in the project development to rationalise the resources. The case under study considers an iron mineral wet magnetic concentration processing plant. The outcome tailings are dewatered by means of thickeners, where the overflow water is recycled back to the plant. The underflow slurry is pumped into intermediate storage tanks before proceeding with further dewatering and final disposal. The project consists of a tailings filtration plant, belt conveying systems, a temporary stockpiling system, trucking loading and transportation system, moisture-conditioning facilities (spreading and airing), and final disposal facilities (compacting). Due to the stickiness of the filtered tailings that governs the belt conveying system design, the operating moisture range must be established. Besides, proper technical aspects such as planning, executing, and analysing both the laboratory and the pilot testing data to validate process design parameters; selecting filters; defining spare filtering capacity; handling the out-of-range filtrated moisture; sizing the belt conveying system; configuring the equipment involved, must be considered.

Nov 8, 2021

This paper describes a mine truck hauling process called "Truck Jigging" which is currently the subject of a process patent application.The investigation explores the production and cost advantages of using the potential energy available in a descending haul truck to assist in elevating an ascending vehicle. Applications are studied for both strip cut mines and open pit operations. Various mechanical connections between the two vehicles are considered, based on a pulley mounted rope system. Fifteen year operating cost estimates show savings of up to 26.5 percent over conventional mine truck operations.

Jan 1, 1989

Kinetic Behaviour of Solid/Solid Separation of Ultrafine Particles in Aqueous Suspension

Sep 13, 2010

By Dunkin H. H

Flotation tests in a laboratory flotation cell at pH 8-8.5 and other sui}plementary tests were carried out on sphalerite-quartz and sphalerite-pyrite-'quartz mixtures. Depression of sphalerite resulted vvhen the addition of copper sulphate exceeded an optimum value. Evidence that this depression was due to collector deficiency because of reaction between copper sulphate and collector is presented. It was not found possible to devise a direct analytical method suitable for .plant control of reagent addition. A possible means of control using potassium cyanide and a higher pH is discussed.INTRODUCTIONAt the Rosebery mill of Electrolytic Zinc Co. of Australasia Ltd., recovery 'of sphalerite in the zinc concentrate occasionally drops unexpectedly. Experiment in the mill and mill laboratory has suggested that one of the factors causing this may be the addition of more than an optimum amount of copper sulphate. On such occasions, an increase in the collector addition improves zinc recovery in the zinc concentrate, but only at the expense of sphalerite-pyrite selectivity.To examine the phenomenon more thoroughly, and if possible to find some means of determining the optimum addition of cepper sulphate and controlling the actual addition at this optimum, one of the authors (W. J. T.) was employed by the Electrolytic Zinc Co. of Australasia' to carry out investigations in the Mining Department, University of Melbourne, under the joint direction of R. B...

Jan 1, 1954

The Bradford Process, Australian Patent No. 11253, has had considerable application in the treatment plants of Broken Hill mining companies, and is at present being used by the North Broken Hill Limited for the treatment of weathered slime accumulations.The "Mining and Scientific Press," of 28th September, 1918, describes the Bradford Process at Broken Hill, specially featuring its application to slime material at the Proprietary mine-the home of the process.The points then stressed for galena flotation were acidulated slime pulp (0.025 to 0.030% H2S04) at temperature 85° to 90° F. and suitable time contact, with 1.5 to 2 lb. of sodium hyposulphite (per ton on slime) to permit the released S02 to "wet" or depressthe blende mineral. Also 1.0 to 1.3 lb. of crude sulphur (per ton on slime) was burnt, to supply S02 for keeping the lead concentrate clean during flotation. Pulp density varied from 23 to 26% solids. Since 1918 the process has been simplified in its application.Acidity of circuit, temperature, and sodium hyposulphite have been dispensed with, and now the S02 is practically all obtained by burning crude sulphur. I The plant units now employed for control and absorption of S02 gas constitute the main advance made in process, and these, with other details, are fully explained in this paper.APPLICATION AT BROKEN HILL NORTHThe existing North Broken Hill Limited gravity mill commenced operations on 9th September, 1909.

Jan 1, 1929

By X Feng, X Zhang, W Sun, Y Zhe, K Hou, B Zhao, H Liu

Pulang Copper Mine, being China's largest newly built mine using block caving, boasts an annual production capacity of 12.5 million tons. Production level and roadway stability hold the key to the successful application of block caving. However, with Tong Kuangyu being the only mine in China which has applied such a method, we currently lack relevant experience in the successful application of the method. This paper has studied the influence of different rock mass zonings, fault thickness, fault dip angles, on-site construction quality on the production level, roadway stability of block caving through numerical simulation and analysed the roadway stability in different kinds of support solutions so as to ensure the successful application of block caving in Pulang Copper Mine. The results have shown that the existing support method in Pulang Copper Mine can meet the requirement of roadway support in zone II and III, but could not satisfy the demand in terms of support strength in the relatively fragmented zone I area. When roadway passes through the fault, the deformation of surrounding rock and plastic zone of roadway will gradually decrease with the increase of fault dip angle; the deformation of surrounding rock and plastic zone of roadway will gradually increase with the increase of fault thickness. An ideal support effect can be achieved through the joint support of grouting and bolting when roadway passes through the fault. In the measured model of on-site construction, there is stress concentration in the intersection between the access and transverse drift of ore removal. Therefore, the stability of the roadway can be improved by improving the construction quality. CITATION:Sun, W, Hou, K, Zhang, X, Feng, X, Liu, H, Zhe, Y and Zhao, B, 2018. Research on supporting technology for production level roadways of block caving in Pulang Copper Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 95–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

A series of in situ pull tests has been conducted to determine the holding capacity of the standard SS46 Split Set Stabilisers. The experiments have been conducted in a wide range of geological conditions ranging from bedded rock to blocky ground. The results presented in this paper indicate that cement grouted split sets bolts are likely to provide up to three times the initial bond strength per metre of embedment length provided by the ungrouted bolts. The increased load transfer capacity of the grouted bolts provides an alternative for permanent excavation support using split set stabilisers.

Jan 1, 1997

By Lancucki C. J, Nickson N. M

X-ray diffraction and differential thermal methods were used to determine the mineralogy of some clays used by the heavy clay industry in the Adelaide area. A detailed analysis was made of the mineralogy and particle size distribution of eighteen samples from beds in two pits in the Recent sediments in the Adelaide plains, of six white clays developed from the weathering of the Adelaide series of sediments, and of four Recent alluvial clays from a pit in the Mount Lofty ranges south of Adelaide. Structural clay products in the Adelaide area are manufactured from mixtures of these clays, so the mineralogy and particle size distribution was determined of eighteen clay mixtures used to make red bricks, cream bricks, facing bricks, pipes and tiles.Knowledge of this mineralogy is important in understanding the ceramic behaviour of the clays.INTRODUCTIONIn this investigation an account is given of the clay mineralogy and particle size distribution of some ceramic clays from the Adelaide area. The clays are used in the manufacture of structura,l clay products and the results to 'be described are part of an overall 'plan of study covering the heavy industrial clays and shales of Australia. Previous work has been published (Cole and Carthew, 1953; Ferguson, 1954; Ferguson and Hosking, 1955; Cole and Nielsen, 1958/59).In this work no attempt has been made to examine clays from all pits engaged in supplying materials for the structural clay industry. However, in 1954 the senior author collected detailed samples from two pits working in Recent alluvial clays in the Allenby·Gardens and Beverley areas near...

Jan 1, 1963