Search Documents

Drum winders have now been built to attain depths of 3000 m and more in a single lift in accordance with the South African Code of Practice SABS 0294, which was introduced at the time of the last hoisting conference in 2000. Since then, this code has not only been followed for several winders in South Africa but was also followed in deep mines in Canada. Design of winders and their braking systems are described in the paper. Koepe winders are in use for high payloads of up to 50 t and to hoisting depths of around 2100 m. As known, the stress range of the hoisting ropes is the key parameter for rope fatigue. However, as per the SABS Code of Practice 0294, relying on static design is not the answer to the question of where the limits are for Koepe installation. The paper describes factors that are recognised to have influence in rope life and suggests definition of new design criteria for friction winders in order to get viable solutions for high-capacity hoisting from deep mines similar to drum hoisting.

Jan 1, 2005

By Doig ID, Phillips HR

As a prelude to studying the sorption desorption and permeability behaviour of coal cores in a triaxial stressing rig using sorb- able gases, the air permeability of typical cores was measured. Lump coal samples were obtained from three gas-troubled collieries in Queensland and New South Wales. These were cored in the laboratory and a simple laboratory permeameter employed which accepted 38 x 40 mm cores in a thick rubber sheath. Air pressure of 500 kPa was applied outside the sheath to provide suitable sealing between the rubber and the coal. Differential driving pressures up to 100 kPa were employed and the air flow measured by displacement of water columns in inverted graduated cylinders. Flow measurements accurate to + 2% could thereby be achieved. Coal lumps were cored both parallel and perpen- dicular to the bedding plane, and were observed prior to measurement for any notable features, in particular for the presence of fissures. Between samples an overall variation of from 100 milliDarcy was found in Appin, Westcliff and Leichhardt coals. Significant variation was observed both from section to section of a core and between regions of a

Jan 1, 1982

By A J. Tucker, L Bottomley

The principle objective of development mining is to create thoroughfares that can be accessed by personnel and machinery for the entire life of an underground mine. The drill and blast process, being the primary method used when creating these thoroughfares, needs to be able to adequately fracture the rock to be removed whilst at the same time minimising any damage that may be sustained to the rock surface that remains. This process of damage prevention is known by a variety of different names including smooth blasting, sculpture blasting, contour blasting and controlled blasting. Whilst the terms are different, the objective is the same and that is to reduce and better distribute the explosive charges to minimise stressing and fracturing of the rock beyond the neat excavation line. The process in this report will be referred to as perimeter control blasting. This paper will discuss the benefits of using perimeter control blasting in a development mining operation and the theories that govern how these blasting techniques work. The methods that are used to implement perimeter control blasting will also be addressed, paying particular attention to how these blasting techniques have evolved, spawning new and improved perimeter control products. Finally some attention will be given to the process of optimising perimeter control blasting in any underground mining operation.

Jan 1, 2005

By Kurihara M

In Japan, shield tunneling method is generally used to drive a tunnel in sand layers around the urban area. In this report, appli- cability of NATM (New Austrian Tunnelling Method), which uses rock bolts and shotcrete as support, to water-bearing sand layers is studied aiming at establishing more economical tunnel driving technique. After the geological exploration, the conditions (i.e. pitch of steel supports, water content, cohesion, and fine content of ground,)necessary to ensure the face stability were investigated by using centrifuge loading tests. Concerning measures to manage ground water, an air permiability test was carried out to investigate the effect of the compressed air to cut-off inflow, and pumping test to study the applicability of dewatering. Furthermore, two dimensional elastic FEM analysis consider- ing progress of the excavation face was perform- ed to analyze stresses in the support system and deformation of the ground, and to investi- gate safety of the support and the ground. From these prior investigations, possibility of the applicability of NATM to the present pro- ject was predicted. Finally, based on these results, a real scale field application test was put into practice to confirm the prediction, and to pursue construction efficiency and phenomena which could not have been predicted Beforehand.

Jan 1, 1987

Some mqre facts and inferences are presented in amplification of a recent paper on the geology of the Kalgoorlie Golden Mile stressing the volcanic origin of its rich gold ores, some of which are considered tobe exhalites. Previously unpublished and largely unmapped pyroclastic features in carbonated and chloritized, but not in amphibolitic, country rock are brought to attention. This applies particularly to the main host, viz. the relatively coarse-grained quartz dolerite greenstone (Q. D. G.), i.e. Golden Mile Dolerite, and gives more credibility to the spatial association of the rich Green Leader and telluride ores with bodies of sediments and tuffites occurring within, or adjacent to, Q. D. G. There may be an intrusive relationship with contiguous mafic amphibolites of doleritic origin, but this is not certain and can only be resolved by morecomprehensive mapping than in the past. Volcanic features have always been recognized in CalC Schist, i.e. Paringa Basalt, more so recently in the shape of coarse volcanic breccia.Iu the subsequent deformation of the gold ores since their inital emplacement there appears to be a structural parallel with some Canadian base-metal deposits, most of them of volcanogenic origin.

Jan 1, 1976

By Likar J, Janexic S, Zigman F

When driving mine roadways in the vicinity of tectonic disturbances and fault zones, sudden outbursts of gas, along with ejections of fine coal, occur. Substantial dynamic changes occur around the roadways in the coal and around the support. The problem has several aspects. Studies have been carried out on the technical analyses of the phenomena which occurred in the Velenje Lignite Mine from 1957 to 1988. The second part of the investigation involves systematic laboratory studies of strength and deformability characteristics of lignite samples and "in-situ" measurements of stress changes during the driving of some roadways. Analyses of events (using the model of limit convergence and the finite element method) showed the possibility of gas outbursts, taking into account the deformability conditions when crossing over from compact lignite to the disturbed region. The rate of advance of roadways and the method of support strongly influence the occurrence of the phenomenon. The preventative measures used in driving roadways under such conditions include trial drilling and the use of blasting instead of machine cutting.

Jan 1, 1992

By Ohga K, Isobe T

Basing upon many and long practical experiences of gas drainage from coal seam and results investigations on the gas flow through in si-tu coal seam using tracer gases,it became clear that solid coal itself is hardly gas permeable or has extremely low gas permeability. Almost all of gas flows from a coal seam into boreholes through fracture net- works intersecting with them.Primary and secondary fractures in coal seams differ in their size and continuity from place to place according to differences of the coal strength and the stress conditions. A lot of gas can be drained through boreholes which intersect with many and/or wide fractures. A mathematical model for gas flow from a coal seam to a borehole through a discoidal fracture is proposed. From the numerical analyses,the apparent radius of the discoidal fracture in this model is shown to be a good indication of the gas drainage ratio. In addition to this,an atempt to make fractures around a borehole using high velocity water jet(ca.lmm dia.,300-700atm., 100-200 1/min.) is introduced.

Jan 1, 1982

Design and construction techniques used to develop two highway tunnels in inaccessible mountainous terrain are described. Measures used to adapt the design to the unusual geology and topography are discussed, as well as measures to adapt the construction methods to available equipment, materials, and skills. Sharp local variations in geoloqic conditions resulted in field modifications to both design and construction techniques. The geology is a volcanic ash and breccia-agglomerate at one site, a jointed andesite at the other, which is also the site of a major landslide. Both rock reinforcement in the form of pretensioned and grouted rock bolts with a shotcrete lining,and rock support by struc- tural steel sets with a reinforced concrete lining were used. A canyonside location and high lateral in-situ stresses required modification of design procedures. Pilot tunnels at both sites resulted in adapting the designs to site conditions with large savings in lining costs, disclosing problem areas in advance of the main excavation, and cushioning of blasting pressure to minimize stability problems.

Jan 1, 1976

Don Hausen was a pioneer in the field of quantitative mineralogy. Methodology that he developed at Newmont almost 40 years ago is still employed today, only the technology has advanced. Petrographic methods were stressed with an emphasis on alteration, mineralisation and paragenesis. Methodologies employed by Don on the Carlin deposit were applied to developing the Carlin Trend by helping to work out lithology and structure, which ultimately led to the discovery of deep high-grade deposits. Quantitative methods used by Don on San Manuel, Copper Creek and Superior, Arizona were applied to the development of the Batu Hijau Deposit in Indonesia. Advancements in technology since DonÆs time have made the mineralogist much more efficient. Manual measurement of peak heights off of strip charts for semiquantitative XRD has been replaced by software that does Rietveld refinement and whole pattern fitting. Hand contouring of XRD data has been replaced by digitised data incorporated into geologic models. Optical point counting, which would take a dayÆs work to process 1000 points, has been replaced by automated SEM methods where 20 000 points are possible in an hour. The use of the optical microscope remains relatively unchanged, and still remains as Don emphasised the æeyesÆ of mineral exploration. However, the information can be relayed much more quickly with digital image capture and electronic data transfer. Don insisted on becoming involved in projects at the grassroots level and supporting the project through mine closure. This made the mineralogist a liaison between exploration geologists, mine geologists, metallurgists and mine engineers. The methodology that Don helped develop continues to provide invaluable support to Newmont geologists and metallurgists worldwide today.

Jan 1, 2008

By Brinkmann J. R

The relative effects of the two basic mechanisms contributing to rock breakage during blasting, shock and gas penetration, are neither well understood nor well characterized, and need further clarification. Blasthole liner (BHL) tests separate the two effects, and by enabling direct measurement of borehole expansion give insight into the shock/gas energy partitioning in rock confinement. The hydrodynamic code DYNA2D is used to simulate the shock effect of the detonation of emulsion in a stainless steel lined hole, and the predicted expansion is compared with experiment. Workers in the past have neglected near-blasthole phenomena and have calibrated models based on stress measurements remote from the blasthole. Extrapolation back to the blasthole has inherent limitations, and indeed, one of the deficiencies of these models is that they have not been able to predict correct borehole expansions, as observed in BHL experiments. DYNA2D has been enhanced by the ICI group with a detonation model which resolves the explosive reaction zone. As a preliminary step towards the ultimate goal of devising a practical damage model, simulations are used to predict the maximum expansion that would take place if the rock were to remain undamaged. Various material parameters are investigated and it is shown that calculated liner expansions are appreciably lower than measured values for high rock yield strengths, while greater than values for low yield strengths.

Jan 1, 1990

By Gordon N

The in situ behaviour of claystone floors associated with the Wallarah, Great Northern and Fassifem Seams has been studied using a comprehensive suite of stress and displacement monitors. The instrumentation was supplemented by in situ and laboratory testing of the claystone materials. The instrumentation demonstrated that the presence of claystone floors is associated with floor heave, extra rib spall, and settlement of the pillar into the floor. Horizontal floor extensometers showed that the depth of extrusion of clay was limited to 1-2 in. A pore pressure transducer installed in a claystone floor demonstrated the possible existence of short-term undrained behaviour of the claystone. Long term swelling of destressed claystone was also documented. Settlement of pillars into claystone floors can be analysed using simple elastic theory. The assumption of plane strain is valid for most claystone thickness/pillar width aspect ratios. Floor heave can be analysed using bearing capacity concepts. However, it is considered that heave is the result of local bearing capacity failure in the rib spall zone. The advantage of this model is that the bearing capacity equation can be applied without resort to unrealistically high factors of safety.

Jan 1, 1992

By Yeliseyev AK, Shestakov AM

Comminution is the most power-intensive process in the technology for ferrous quartzite concentration. That is why improving comminution efficiency leads to the most appreciable economic effect on the concentration process. The trend towards reducing the lump size of crushed ore before charging the mill is considered to be of major importance in improving comminution efficiency. A considerable number of investigations have been performed in this direction. At the same time, a strong interest is also maintained in the increase of comminution efficiency due to optimisation of process taking place in the mill. Recently, investigations of the power intensity of the breaking process inside the mill have been carried out at the Krivoy Rog Mining Institute. It was ascertained that the routine conditions of comminution at a low mill ball charge ratio resulted in an unnecessarily high power consumption due to the force of impact of falling and milling bodies far exceeding the power required for comminution. For example, the power value for falling balls of 60 - 125 mm in diameter reaches 0.3 kNm, and the force and stress due to ball contact with the lining reaches 60 kN and 250 MPa respectively. These values exceed the force required for comminution by a factor of ten. Analysis of the mechanism of ore particle size reduction during comminution in the ball mill indicates that the size reduction is due to impact load, attrition load, and static load. The efficiency of size reduction is very low. During comminution in the ball mill, impact loads prevail and amount to 85 - 90 per cent of the total load. In this situation, not more than 10 - 15 per cent of destruction is due to attrition.

Jan 1, 1993

This paper traces briefly the reasoning which led to the decision to extend the existing internal shaft at the Rosebery Mine and to instal underground a larger winder (No. 2 Hoist) with capacity to handle all hoisting requirements to a depth of approximately 2,500 ft. on an incline varying from 83" to 55" to the horizontal. It then covers the specifications and selection of the winder, the design of the winch chamber, rope raise and bins, the excavation, support and lining of the chambers and the transport to site and installation of the machinery. Finally a brief description is given of the mechanical and electrical parts of the winder.INTRODUCTIONThe existing shaft winder on the internal inclined shaft situated on No. 8 Level of the Rosebery Mine had reached the limit of its capacity. Hoisting 21-ton capacity skips in balance, with a 13/16-in. diameter rope, it required four layers of rope on the 3 ft. 6 in.drums to reach the loading station under No. 12 level at a depth of 864 ft. (Fig. 1). This entailed heavy wear on the multi-layered rope and heavy stresses on the cheeks of the drums. Continuous working on three shifts was necessary to handle ore, men and materials, and a hold-up from any cause whatever meant an interruption to production on the lower levels of the mine. The maximum output of the hoist whilst hoisting from the No. 12 level loading station was 50 tons per hour. It was obvious therefore, that a larger winder was required if output was to be maintained.Diamond drilling had proved the existence of sufficient ore at depths well below No. 12 to warrant exploitation and a decision had to be reached on the means of hoisting this ore.

Jan 1, 1958

By M P. Schwarz

This paper describes modelling studies of the flotation cells used by BHP Billiton Nickel West Ltd in the slimes circuit at Mt Keith. The aim is to achieve a better understanding of the hydrodynamic limitations in the existing cells to improve nickel recovery. Computational fluid dynamics (CFD) simulations have been performed on the 100 m3 mechanically-stirred cells. The data produced by the simulations include velocity vectors, gas holdup distribution, solids distribution, bubble size, superficial gas velocity and turbulent parameters. These results have been checked and found to match hydrodynamic measurements at the plant. An analysis of the data found that one of the limitations in fine particle recovery was related to the air bubbles discharged with the tailing. The air in the discharge was caused by the high viscosity of the pulp. In the presence of fine particles, the pulp exhibits high viscosity with a yield stress. The increased drag due to high viscosity caused the bubbles to rise more slowly up the cell. This results in a significant hold-up of bubbles, some of which report to the tailing with associated loss of valuable minerals. A parametric CFD study of the operating variables shows that less air would be discharged in the tailing by decreasing the following: air flow rate,pulp density,stirring speed, andfrother addition. Simulation results indicate that these changes would cause a lowering of the air hold up in the cell especially near the discharge area. Predictions of the bubble-particle attachment rates under various operating conditions have also been calculated. Although it is possible to increase attachment rates by increasing stirring speed or by increasing pulp density, the amount of air discharged and the amount of nickel loss through the tailing will also increase. The project showed that CFD modelling is a powerful tool for studying hydrodynamic effects of bubble-particle interactions in flotation cells.

Jan 1, 2008

By Hargraves A. J

At 4 MPa gas pres ure and 30°C the sorptive capacity of 10 selected Australian dried coal ranges from 17 to 23 m3/tonne of CH4 and 27 to 36 m3/tonne of CO2. Values for moist coals are about 25 per cent less. At 20°C, sorptive capacities are about 18 per cent greater. No clear relationship between coal rank and sorptive capacity was established.The permeability of coal to gas is dramatically reduced by progressive hydrostatic confinement. No single 'permeability' for a coal can be established because of relative affinities of coals and the gases (Ar, CH4 and CO2) used in experiments. Bedding plane permeability is significantly greater than permeability normal to bedding. Dependent on gas/coal combinations, permeabilities without confinement ranged from 150 to 0.05 millidarcies, and with 8 MPa hydrostatic confinement from 1.0 to 0.001 md. Generally, permeability is increased by reduction in temperature, and reduced by increase in moisture as one changes from Ar through CH4 to CO2. In retrospect, it is preferable to ubject permeability sample to 8 MPa hydrostatic stress only once, because changes occur in the samples and it is difficult to use other gases successively.The initial rate of desorption, DP, does not appear to be a reliable index of proneness to instantaneou outbursts for Australian coals.The methods used for determining quantitative gas-coal properties appear suitable and reliable for testing other coals.

Jan 1, 1985

By M Hudyma

Open stope mining is the most common mining method employed in underground, hard rock mines in Canada. It is characterised by relatively small, single lift stopes (20 000 to 100 000 tonnes), and fast stope turnaround times. Host wall rock mass conditions, which are typically poor to fair, are the controlling parameter in stope dimensioning. Rock mass stability is maintained by designing all stope surfaces at a stable dimension, and through extensive use of cablebolting for stope backs and frequently stope hanging walls. Dilution control is a high priority. The typically small, high-grade, deep and irregularly shaped orebodies are incrementally developed, usually in a bottom to top direction. In many cases, high stress is encountered due to the depth of the orebodies. Overstressing of pillars and hanging pillars are avoided through the use of pillarless or early pillar recovery mine sequencing strategies. Stopes are invariably filled, and in higher grade and wider orebodies, cemented fill is commonly used. This paper generalises many of the similarities found in Canadian open stope mines.

Jan 1, 2000

By C R. Fountain, W R. Cannings

The zinc-lead-silver mineral resource at Lady Loretta ranks amongst the worldÆs richest when measured in terms of in situ metal grades. However, the project remains undeveloped 28 years after its discovery in 1969. The primary obstacle to development has been the fine and complex grain structure of its ores, which make flotation concentration inefficient even with fine grinding. The size and remote location of the deposit have also hindered exploitation. BUKA planned to directly fume the volatile target metals from the ore when it acquired the project. Intensive, post-acquisition modeling showed the innovative processing route to be uneconomic, notwithstanding high metals recovery and low waste content in fume product. Progressive modifications and supplements to the underlying fuming process enhanced economics and resulted in a new mine-to-metal processing route for zinc-lead-silver ores. The proprietary, three-stage BUKA Zinc Process offers technical, economic and environmental advantages. It is expected to find widespread application in the treatment of ores and residues. However, neither continued R&D nor application to Lady LorettaÆs currently delineated resource can be justified under prevailing market conditions. The objectives and results of each step in the process development sequence are outlined with reference to their impact on the commercial viability of the Lady Loretta project.

Jan 1, 1998

By E Garbarino, P Molina, V Badino

Given the ever increasing quantity of construction and demolition waste (C&DW), one of the most challenging issues presently facing policymakers and public administrators in Italy concerns how to organise and manage collection and recycling and to understand whether and to what extent recycled aggregate can complement natural building aggregates in a sustainable supply mix (SSM). The paper presents the results of a research aimed at analysing energy and environmental implications of the C&DW recycling chain in the administrative territory of Provincia di Torino in northern Italy. In respect of a population of about 2.25 million inhabitants, the annual production of C&DW in the area under study is 1.8 Mt. A combined geographical information system (GIS) and Life Cycle Assessment (LCA) model was developed, paying attention to the geographical location, land use, transportation network and avoided landfill: crucial issues for sustainable planning and management. Around 90 recycling plants were classified according to the size, typology (stationary, semi-mobile and mobile) and physical- mechanical characteristics of the recycled aggregate. Under different assumptions relevant to the delivery distance, and considering the typology and grade of recycled aggregate, as well as local availability of natural aggregates, it was possible to evaluate the geographical coverage of aggregates demand and to use LCA in order to identify and quantify energy and environmental indicators.

Jan 1, 2009

Underground measurements, observations and computed simulations, started a long time ago were concerning the study of : - occurence of typical rockburst, - inducing, stretching of main fractures in the roof of caved longwalls. They made obvious a foundamental phenomenon of inducing of strata fractures involving contact be- tween two layers quite different in their elastic characteristics : coalseam and rocklayer.. The start of primary cracks in maximum abutment zone takes place in the rock near the contact surface. It is opening of crevasses induced by traction stress component resulting of difference of rigidity of both materials and no sliding on in- terface. Occurence and stretching of these crevas- ses are a rheological phenomenon so that the rate of advance and stops of the face influence the distance between the crevasses and the stretching of these ones. The characteristics of these cracks in space and time affect mining conditions. So it is for fractures proximity and expan- sion inducing eventual blocks formation in longwall roofs in front of faces, for depth and delay of road- ways ribsides fracturing, inducing some rockbursts. In longwalls roofs, cracks initiated in front of a face can be either quite close or quite distant each from the other one, according to the depth of crushed coal in front of the face, which af- fects also extension of the cracks.

Jan 1, 1988

By P Commander

Western Australia is a major exporter of minerals, which places significant economic and environmental responsibility on Government and the stateÆs mining industry. Moving into the 21st century, mineral production in Western Australia is $14 billion accounting for 50 per cent of the stateÆs export income. There are over 60 large-scale mining operations distributed throughout the arid regions of the state (less than 300 mm/year rainfall). There are four key mineral provinces in arid Western Australia including the Pilbara (iron ore), Murchison (gold), Northern and Southern Goldfields (gold and nickel). These provinces have significant differences, particularly in respect to groundwater demand from mining and mineral processing, aquifer systems that are utilised, and approaches to groundwater management. The arid nature of the stateÆs interior and subsequent lack of surface water resources has required substantial groundwater resource development by the mining industry. A variety of aquifers have been explored and utilised ranging from shallow alluvium and calcrete, discrete fractured zones in bedrock, concealed palaeochannels and inland sedimentary basins. Groundwater usage by the mining industry is about 150 GL/year with most abstraction related to mine dewatering, mineral processing and dust suppression. Groundwater abstraction in Western Australia is regulated by the Water and Rivers Commission. In the Goldfields, the depletion of brackish (>2000 mg/L) and saline groundwater from storage is permissible, as mining is considered the beneficial use for groundwater which may be as much as 200 000 mg/L. In contrast, the low salinity groundwater of the Murchison and Pilbara is allocated on a sustainable basis. The role of monitoring and ongoing aquifer reassessment is crucial in water management, in evaluating the condition and performance of stressed aquifer systems. Mining operations face a variety of water resource issues ranging from insufficient availability for processing to excessive mine dewatering. These issues also change as a mine operation proceeds through its development, commonly starting with a deficiency and moving into surplus as deeper pits require more dewatering. Operating mines have to contend with three main issues: water supply, wastewater disposal and contamination of local water resources. In contrast, post closure issues are related to aquifer recovery or re-establishment of groundwater equilibrium, development of pit lakes in mine voids and isolation of waste products and associated seepage or run-off.

Jan 1, 2003