Search Documents

By T Kojovic, S J. Windle, J Sullivan

"The Geometallurgical Mapping and Mine Modelling (GeM) comminution index (CI) was developed as part of the AMIRA P843 GeMIII project. Drill core geochemistry samples were passed through a Boyd Crusher with standardised settings and the resulting particle size distribution (PSD) was measured using sieves.Disadvantages of the original measurement were the relatively coarse crush size, requiring a second pass of crushing for geochemical sample preparation, and the limitation of throughput caused by the sieving step. At Antamina, the measurement has been modified to use a 2.2 mm crusher size setting, which permits a single pass. The PSD is measured using a Camsizer, an automated optical sizing instrument. The Camsizer sample is a +180 µm fraction, used to avoid passing too many fines through the instrument and slowing down the measurement. In the sieving step, the weights of the two fractions are recorded and subsequently used to normalise the distribution measured by the Camsizer. In this way, the throughput of the Camsizer can match that of the Boyd Crusher. The PSD data are therefore measured without penalising the throughput of the sample laboratory.The normalised PSD distributions are used to derive modified CI parameters, based on the slope and intercept of the breakage product size distribution, which are indirect measures of the material breakage hardness.Fifty samples were selected as a training set, each sample a composite of five or six individual assay intervals and each with its own measured CI. The average PSDs were calculated for the composites and used to calculate a composite CI. The intact half of the core, approximately 40 kg, was tested to measure the BWi, A*b and crushability. The results were used to develop predictive algorithms for these hardness parameters.A further 50 composites were chosen for lab testing, to serve as a blind test of the algorithms. The paper reports on the test results and the incorporation of the modified CI data and predicted hardness parameters into the Antamina block model.CITATION:Windle, S J, Kojovic, T and Sullivan, J, 2016. Use of a Modified Comminution Index to Predict Bond Work Index and SMC A*b at the Antamina Mine, Peru, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 153–160 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By C Rothfuss, X Wang, S J. Herbert, K Prasad

The extraction of groundwater to produce gas from coal seam gas (CSG) reservoirs has highlighted the opportunity for beneficial uses of groundwater in Australia. This paper presents an assessment of alternate groundwater modelling approaches that can be used for assessment of one beneficial use option, that of injection. This assessment examines the outcome of the use of different simulation methods on predictions of hydrodynamic behaviour.In this paper, a simplified hydraulic concept of a multi-aquifer system within the hypothetical injection field was used to investigate the hydrodynamic behaviour of injection into the Precipice Sandstone. Comparisons were made through the analysis of a Theis 3D analytical solution with 2D and 3D numerical solutions. The paper discusses the different solution methods and the impact of these on predictions of pressure and flux. Differences in 2D and 3D solutions result in implications if planning injection as a beneficial use of water. For example, the 2D solution resulted in faster and higher injection pressure build-up when compared to the 3D solutions. The 2D modelling could result in either plans that require higher capital expenditure for a greater number of wells in order to spread the pressure effect and remain below the maximum injection pressure or a reduced injection rate. Meanwhile, the 3D modelling with sensitivity analysis could result in planning for lower capital expenditure for fewer wells required to spread the pressure effect and remain below the maximum injection pressure. CITATION:Wang, X, Herbert, S J,?Rothfuss, C and Prasad, K, 2013. Assessment of effectiveness of artificial recharge for coal seam gas water management based on numerical modelling, in Proceedings Water in Mining 2013 , pp 67-72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By K Johnson, G Morrison, N Lisowiec

The Mount Wright gold deposit is located near the town of Ravenswood, ~90 km south of Townsville, in north Queensland. The deposit has been mined by underground methods since 2006. It produced approximately 138 koz Au in the 2011 - 2012 financial year and has a total endowment of approximately 1 Moz Au. To facilitate near mine exploration, a re-logging campaign of 600+ diamond and RC drill holes was recently conducted, resulting in a revised three-dimensional (3D) geological model and improved understanding of the ore controls and the mineralised system. The deposit is within a Permo-Carboniferous breccia complex approximately 350 m diameter and more than 1200 m deep. It consists of early peripheral granite-rich breccia, polymict breccia, a rhyolite spine and a late tuffisite (fine-grained milled breccia) pipe. The rhyolite spine is approximately 60 m + 250 m + at least 1200 m deep and is zoned with massive, flow-banded and breccia phases that are in part gradational with the other breccias. There is extensive sericitic alteration centred on the tuffisite and rhyolite units and fading out into the shallower and peripheral polymict and granite-rich breccias. There is also a broad pattern of metal zoning with elevated Pb-Zn ¦ Ag in the upper 400 m, Au-Cu-Bi below 400 m fading out below ~850 m, and a poorly defined deep Mo-W-Te-Sb anomaly. The majority of the Au ore is between 400 and 850 m below the surface in the rhyolite spine. Below this, Au mineralisation is less coherent, and more localised in the margins of the rhyolite and in the adjacent tuffisite. The developing model is that the ore is not confined to or necessarily directly genetically related to the rhyolite spine, but is driven by other phases of intrusion that also generated the tuffisite pipe. This model is being used to generate additional drill targets away from the present mine development.CITATION:Johnson, K, Morrison, G and Lisowiec, N, 2013. Advancing near-mine exploration with an updated geological model for the Mount Wright gold deposit, Queensland, in Proceedings World Gold 2013 , pp 469-478 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By J Seppelt, B Akerstrom, J Bubnich, D Seaman, T Waters

The Cadia Hill concentrator at Newcrest’s Cadia Operations has undergone several modifications and upgrades to treat an increased throughput rate of harder ore from the Cadia East block cave mine.Subsequent to the commissioning of the expanded circuit, the flotation cleaner block has undergone a systematic optimisation programme tackling all facets of circuit operation. This included debottlenecking circuit constraints and installation of Jameson cell technology to enhance copper and gold recovery while rejecting fluorine and gangue from the concentrate.This paper outlines the improvements over the course of the project and results obtained from the implemented actions.CITATION:Akerstrom, B, Seppelt, J, Waters, T, Bubnich, J and Seaman, D, 2018. Cleaner circuit optimisation at Cadia Operations, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 457–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

Burra was the largest metalliferous mine in Aus- tralia between 1845 and 1860 and employed as many as 1000 men and boys. The workforce was predominantly Cornish, Burra being the first con- centration of Cornish folk in Australia. The sur- face and underground mining operations were typically Cornish and virtually all positions of responsibility were held by Cornishmen. Beam pumping and winding engines were imported from Cornwall and housed in traditional Cornish engi- nehouses. Burra had the first significant number of beam engines in Australia: six were installed between 1849 and 1861. These engines, ranging in size from 20 inches to 80 inches in diameter, were used for pumping, hauling, and driving Cornish roll crush- ers and dressing machinery. Derelict enginehouses of the great beam engines are a striking reminder of former mining activity in Cornwall and South Australia. In South Aus- tralia about 35 enginehouses were erected between 1848 and 1887, of which eight still remain, three of them at Burra (Figure 1). These remain as a tangible link with the Industrial Revolution.

Jan 1, 1987

By S Zheng, Y Zhang, Z Wen, S Ma

Red mud (RM) is a solid waste product generated during alumina refinery process, and is usually stored in SFs (SFs) because it canÆt be disposed of easily. In this paper, environment degradation caused by RM-SFs was systematically assessed by the method of single factor pollution index based on the analysis data of water, soil and atmosphere sampled around one newly-built and one decommissioned RM-SFs, which are managed by an alumina production company in China. The results revealed that the ambient environment around RM-SFs is seriously polluted by alkali and mercury (Hg). The pH value of RM leachate, surrounding surface water and groundwater are all higher than the limit of water quality standards in China. And as a possible result of overflowing of high alkaline leachate, soil pH value for the decommissioned SF decreases with increasing distance between the sample collection points and the closest side of RM storage facility (RM-SF). Total Hg concentrations in RM leachate, surrounding surface water and groundwater all exceed Grade III limits of ChinaÆs Environment Quality Standards for Surface Water and Groundwater. However, the air quality was little affected as the daily average of TSP in the air is below grade II values of Chinese Ambient Air Quality Standard.CITATION :Wen, Z, Ma, S, Zheng, S and Zhang, Y, 2012. Assessment of environmental quality impacts caused by red mud storage facilities in China, in Proceedings Life-of-Mine 2012, pp 51-58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Q Zhou, G Barrett, Y Choi, J Jiang

As part of a general review of processing double refractory ores through Barrick GoldÆs autoclaves /carbon-in-leach (CIL) facility at Goldstrike, a study was made to evaluate the use of surfactants for reducing the loss of gold during cyanide leaching of preg-robbing gold ores. Consistent improvement of gold recovery was observed with surfactants at various testing conditions. This paper will discuss the results obtained from laboratory and pilot-scale testing, as well as, review potential mechanisms for the observed improvement in gold recovery.CITATION:Zhou, Q, Barrett, G, Jiang, J and Choi, Y, 2013. Surfactants for gold recovery improvement with preg-robbing gold ores, in Proceedings World Gold 2013 , pp 367-372 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By W T. C Kendall, H D. Ngo

Garden Well is a shear-hosted Archaean orogenic gold deposit located 100 km north of Laverton, Western Australia. The Garden Well processing plant is designed for a nominal 491 t/h milling rate and annual capacity of 4 Mt. The plant has three key innovations:1. a scrubbing circuit, expected to reduce grinding power consumption by up to 20 per cent2. a secondary cycloning/gravity circuit, providing a second opportunity for gravity gold recovery (additionally, the circuit effectively increases the leach residence time of the coarse gold bearing fraction of the leach feed by approximately 60 per cent, without any additional tankage)3. the use of mid-stream oxygenation to enhance gold recovery.The Garden Well deposit is free-milling with overall laboratory gravity/leach gold recoveries exceeding 95 per cent at a P80 grind size of 150 ¦m. Three mineralogical domains have been identified: oxide, transition and fresh, with the fresh domain having subdomains of fresh ultramafic and fresh shale. There is a high component of gravity recoverable gold in all three domains.This paper will discuss these innovations and the design challenges and the risk mitigation strategies that were adopted to ameliorate the prototyping risk. The performance of the plant since commissioning together with lessons for the future will also be presented.CITATION:Smith, R J, Kendall, W T C and Ngo, H D, 2013. Treatment plant innovation at Garden Well, in Proceedings World Gold 2013 , pp 315-324 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By J Zhou

Gold in sulfide ores is associated predominantly with sulfide minerals and occurs as both microscopic and submicroscopic particles. In non-refractory sulfide ores, gold occurs mainly as coarse- and medium-grained particles. Minute inclusions and submicroscopic gold usually account for a minor portion. In contrast, gold in refractory sulfide ores occurs mainly as minute particles and submicroscopic gold, and microscopic gold usually accounts for an insignificant portion. In gold ores containing carbonaceous material, the preg-robbing nature of carbonaceous material may impose challenges on gold extraction and cause gold losses. To extract gold from refractory sulfide ores, the ore needs to be finely ground and preoxidation is often required. Sulfide host minerals must first be oxidised to create a porous structure through which the cyanide leach solution can penetrate to reach the colloidal gold particles. The oxidation is traditionally achieved by roasting, autoclaving or bacterial oxidation. In carbonaceous sulfide ores exhibiting a preg-robbing nature, the carbonaceous material needs to be treated by roasting, autoclaving or other means to minimise the preg-robbing effect. As a predictive and troubleshooting tool, the gold deportment study plays an important role in gold metallurgy. It determines the deportment of gold in an ore or mill product and identifies the mineralogical issues that may affect or may have affected gold extraction. The information acquired from a gold deportment study can be used to assist in process selection, flow sheet development, recovery improvement and reagent optimisation.CITATION:Zhou, J, 2013. Deportment of gold in sulfide ores and implications for gold extraction, in Proceedings World Gold 2013 , pp 433-442 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By M Barden, G Lane, B Quilliam

NQ Minerals PLC, through Hellyer Gold Mines Pty Ltd, plans to reprocess the contents of the Hellyer tailings dam to produce lead/silver concentrate, zinc concentrate and pyrite concentrate (containing Au and Ag). This paper discusses the project development, mineralogy, metallurgy and chemistry of processing Hellyer tailings and the associated environmental benefits. The Hellyer and Fossey orebodies were volcanic hosted polymetallic massive sulphide deposits located within the Mount Read volcanic arc of western Tasmania. Mineralisation was hosted in massive sulphide (pyrite) and comprised predominantly of sphalerite, with lesser galena, chalcopyrite and arsenopyrite. The Hellyer orebody was mineralogically complex (fine grained) and was treated through differential flotation with initially modest recoveries. Fossey ore processing characteristics were similar to those of Que River ore and simpler than Hellyer but treatment still resulted in significant grades in flotation tailings. CITATION: Lane, G, Barden, M and Quilliam, B, 2018. Hellyer tailings – complex mineralogy but higher grade than many ore bodies, in Proceedings Complex Orebodies Conference 2018, pp 35–38 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By K Evtiminova, G Jobson, M Nolte, S Meik

Chelopech Mining EAD (CMEAD) is a wholly owned subsidiary of Dundee Precious Metals Inc (DPM) and operates the Chelopech underground mine and processing facility located in Bulgaria. The final product sold is a flotation concentrate containing copper minerals with associated gold and silver. The increase in production from 0.6 to 1.0 Mt/a by 2009 occurred with the original (1975) secondary/tertiary crushing, and primary/secondary ball mill circuits. As part of the mine/mill upgrade project to 2.0 Mt/a, a new single stage semi-autogenous (SAG) mill and ancillary equipment was installed, replacing the original circuits, with commissioning occurring during the first half of 2011. Aspects of the design, commissioning and operation of the new comminution facility are the subjects of this paper.An extensive program of comminution characterisation test work was completed in 2004/2005, which indicated moderate hardness and competency characteristics. The characteristics were considered suitable for a range of comminution approaches which were assessed with respect to power requirements and capital and operating costs. Retention of the existing primary crushing facility, and installation of a new single stage SAG mill located within the existing mill building, was selected as the design for the expansion.An extended ramp-up schedule for the overall concentrator upgrade turned out to be necessary as the comminution and flotation circuits were completed prior to several downstream unit processes (concentrate filtration and tailings thickening), which were required to reach the design mill feed throughput rate on a sustainable basis. This resulted in the opportunity to gradually increase the SAG mill ball charge as necessary, to obtain the throughput corresponding to the various downstream processing constraints.A relatively fine cyclone overflow stream particle size distribution is a feature of the Chelopech comminution circuit that has not been fully overcome with increasing ball charge conditions. However, design throughput has been met even under the finer product size conditions and will be consistently achieved following the commissioning of two further process improvement projects scheduled for late 2012.CITATION:Jobson, G, Nolte, M, Evtiminova, K and Meik, S, 2012. The modernisation and upgrade of concentrator operations at the Chelopech Mine, Bulgaria - Design, installation and operation of the 250 tonnes per hour comminution circuit, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 325-332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By M G. Wansbone, R Bhargava

The inferred ground conditions for the proposed mined cross passages at the northern end of the Waterview Connection tunnels consist of an overburden of alluvial and residual soils, with mixed face geology of highly weathered to unweathered extremely weak rock. This paper describes three-dimensional (3D) finite difference analyses undertaken to evaluate the stability of the cross passage headings and to validate the proposed sequence of excavation. The analyses undertaken incorporated the influence of the construction of the mainline tunnels and the breakout opening in the segmental lining for construction of cross passages.The stability analyses were carried out using FLAC3D™, version 4.0 (by Itasca Consulting Group) by progressive reduction of shear strength parameters to obtain a failure condition and estimate a factor of safety. For each step of strength reduction, corresponding increments of displacements of several points on heading faces were monitored. The stability obtained from numerical analyses was compared with analytical solutions. Interpretation of results of drained analyses indicated instability of the upper 2 m of heading face within the highly weathered rock mass. Additional analyses were undertaken by including grouted fibreglass dowels to reinforce the heading face. The results of the additional analyses showed significant reduction in displacements and yielding of ground around the face. The proposed temporary support comprised face reinforcement using grouted fibreglass dowels in conjunction with canopy tubes and perimeter support of steel fibre reinforced shotcrete. The stability of the construction sequence, which was related to the specific requirement of the proposed excavation equipment, was validated.CITATION:Wansbone, M G and Bhargava, R, 2014. Analysis of stability and design of face support for cross passages – Waterview Connection tunnels, Auckland, New?Zealand, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 339–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

This paper presents a rationale for selecting appropriate support elements which combine to form a support system to maintain stability in mines subjected to both strainburst and the shaking that occurs from fault slip. The overall approach was developed during the 'case for safety' study undertaken to allow the then Beaconsfield Gold mine (now Tasmania mine) to resume development and production after the 25 April 2006 ground-fall and fatality that received worldwide publicity. Issues of the sometimes competing requirements of support element performance during dynamic loading are discussed and the need for support flexibility is contrasted with the usual high support element stiffness required when these are used to reinforce rock masses. An example is presented to show the steps and technical details required to design each component of a support system to counter the de-stabilising effects of seismicity.

Nov 25, 2010

By B Upton, J Mitchell

The use of hydro scaling and in-cycle shotcrete to replace conventional jumbo scaling, mesh and bolting as the primary method of ground control for run of mine development has been investigated through extensive trials at the Waroonga mine, Agnew Gold Mining Company.These trials have progressed from investigating the productivity aspects of the method through to a three month mine-wide trial, which may yet lead to the adoption of this potentially best practice ground control technique at Agnew.Ov erseas trials and research have shown that hydro scaling results in a significant improvement in the shotcrete-rock bond strength. Good adhesive bond strength ensures that the shear strength of the shotcrete layer rather than itÆs flexural or tensile strength is fully mobilised as rock mass reinforcement.This maximises shotcretes ground reinforcement capability and it is suggested that a bolt-less fibrecrete support design is feasible using the hydro scaling technique.

Jan 1, 2005

By K G. Harding, A Osman, A du Toit, F K. Crundwell, C M. Sheridan

"Most mineral processing plants have high water requirements for their operational activities. These plants often function in an environment where water is becoming increasingly scarce. An increase in population will result in an increased demand for water; potentially beyond the limits of supply and hence increased competition for the resource. In South Africa, Gauteng and the North West Province are likely to be first to experience a shortage of potable water.In order to avoid a water crisis, efforts must be made to ensure the effective management of water resources and the minimisation of wastage. Hydrometallurgical plants have a responsibility to society and the environment to operate in a sustainable manner - reducing their water requirements will certainly assist towards developing a sustainable footprint.This project improved site water management by: surveying the potable water and storm water systems with a view to assessing the current water accountability and determining methods to improve accountability determining the monthly and yearly water balance for the site and presenting it in the form of a water balance sheet drawing up an input-output and operational model in accordance with the Minerals Council of AustraliaÆs æWater Accounting Framework for the Minerals IndustryÆ calculating the water footprints of the refinery identifying ways in which water savings could be achieved recommending management systems for water usage monitoring.This work was conducted in South Africa. The value of this work lies in that it established the current baseline and assisted in developing management systems that can reduce water usage sustainably.CITATION:Osman, A, Crundwell, F K, Harding, K G, Sheridan, C M and du Toit, A, 2013. Water accountability and efficiency at a base metals refinery, in Proceedings Water in Mining 2013, pp 277-286 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By R Dunne, J Dodd, J Snyder, F Roberto

Energy costs are steadily increasing worldwide while the availability and quality of water are becoming contentious issues between the users (municipalities/households, agriculture, manufacturing and mining). Refractory gold ore treatment - pressure oxidation, biological oxidation and roasting (ultra-fine grinding, or UFG, will not be discussed here as this process only reduces the particle size of the feed prior to cyanidation) - requires substantially more energy and water quantity and quality are vastly different compared to the standard and simple flow sheets used for treating non-refractory ores This paper will provide an overview of the energy and water requirements for treating refractory gold ores, a topic which does not appear to have been considered previously in the literature.CITATION:Roberto, F, Snyder, J, Dodd, J and Dunne, R, 2013. Energy and water requirements in the treatment of refractory gold ores, in Proceedings World Gold 2013 , pp 527-532 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By R J. Wood

Raise drilling (or raise boring) is not a new technology or methodology. The first raise drilling machine was developed by The Robbins Company (TRC) of the USA in 1962. TRC manufactured the first tunnel boring machine (TBM) in 1952 and Jim Robbins, the founder of the company wanted to ‘turn the TBM concept on its head’ so to speak.Many improvements have ensued in the 50 years since the first machine. Such improvements include advances in the drill rod and thread design, cutters and reaming heads. Raise boring would not have been possible without the development of the tungsten carbide insert cutters and there have been big advances in both the carbide technology and in the mechanical design of the cutters.Over time mines have developed deeper with a greater use of diesel equipment resulting in greater ventilation requirements. This in turn means larger and deeper ventilation shafts. There have also been improvements in directional drilling techniques. This all combines with the need and ability to construct larger shafts using the safe method of raise drilling. With suitable geotechnical conditions the RBR900VF is capable of drilling shafts to a diameter and depth of greater than 8 m and 2000 m respectively. Greater diameters are possible over shorter lengths with suitable ground conditions.The RBR900VF was designed and manufactured to specifications developed by Macmahon. This machine has the greatest thrust and torque capability of any machine in the world. It enables cutters to be more heavily loaded in the larger diameter heads and this is essential for efficient rock excavation. Additional features of the new machine include minimal manual handling to provide a safer working environment and higher strength steel for the drill rods providing additional safety margin.CITATION:Wood, R J, 2014. A revolution in raise boring – the development of the RBR900VF, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 171–178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By T N. Little

This paper is concerned with the influence of engineering geology on design of Wall Control Blasts. In the Introduction, the Blast Management Framework and the Blast Design Requirements classification system (previously developed by the author) is drawn upon to set the context. Blasting objective for all wall control blasts involves both profile and damage control. Four classes of approaches for blast design are outlined and briefly discussed. Five distinct wall control blasting techniques are summarised. The general relationship between geology and blast design is explored in the paper. Influence of geology on pre-split and post-split design and blasting direction is highlighted. Wall damage modelling from the closest row of blastholes is also introduced using the Analytical Damage Model (ADM). The relationship of rock properties and explosive selection and in particular the Mach wave generation is introduced to assist blast designer in this regard. Finally a Conceptual Model that relates vibration, damage and rock mass condition has been presented along with some applications that have been undertaken by the developer. Eight conclusions have been formulated based on extensive work in this area and the current study.

Jun 22, 2022

By H W. Wu, T Harvey

An overview is given of two new developments in mine atmospheric monitoring. A new personal dust monitor (PDM) that gives real-time respirable dust readings is discussed. The unit is mounted within the minerÆs cap lamp battery and internally measures the true particle mass of dust collected on its filter. Samples are available for later mineralogical analysis and results do not exhibit the same sensitivity to water spray as optically-based measurement approaches. The technique achieves microgram-level mass resolution even in the hostile mine environment and reports dust loading data on a continuous basis. The monitor has been evaluated under an Australian Coal Association Research Program (ACARP) grant and is being adopted for statutory mine respirable dust determinations in the United States (US). The monitor has particular application for determining location of high dust sources. It can evaluate the efficiency of engineering means of suppression and other approaches to reducing dust levels. It has been recognised that the PDMÆs unique measurement approach has application to allow real-time atmospheric diesel particulate matter (DPM) monitoring. The industry has no real-time atmospheric DPM monitor at present. Recent surveys in New South Wales and Queensland show significant numbers of miners continue to face full shift DPM exposures in excess of internationally accepted levels. Real-time DPM monitoring will allow the industry to pinpoint high exposure zones where a number of trucks and other vehicles work in areas of poor ventilation. Knowledge of high DPM concentration zones allows efficient modification of work practices to reduce underground minersÆ exposure. Approaches to uses of the DPM form of the monitor and the design of tag boards are discussed. Some outcomes from mine tests with both these new instruments are given.

Jan 1, 2008

By L Nagy, K P. Juhasz

The authors were engaged to optimise a traditional rebar cage reinforced concrete segmental lining by means of finite element analysis (FEA) using macro synthetic fibres for the Shanghai metro extension. The aim of this study was to reduce or entirely replace the original steel reinforcement of the segmental lining, in order to make the precast production process faster and more economic. The outer diameter of the tunnel was 6200 mm, the thickness of the segments was 350 mm.The numerical calculations were performed by Atena Finite Element software, which is based on the combination of Menétrey-William and Rankine failure surfaces on the compression and tension sides respectively. The effect of the macro synthetic fibres was modelled as tension stiffening on the tension surface.A one-to-one full scale model of an assembled tunnel ring using the original reinforcement cages was tested at Tongji University in Shanghai, July 2013. The ring was tested to differing load levels where load and displacement were measured until failure. The author’s first step was to calculate the real displacement characteristics of the original reinforced concrete (RC) ring, then calculate the numerically modelled version, so as to compare them. The material parameters of the concrete and rebar used had been determined through basic material tests conducted at the Tongji University. (Bi, Liu and Wang, in press).The numerical modelling undertaken has shown good correlation with the full-scale physical test results. Optimisation of the lining reinforcement was achieved through the addition of fibres, resulting in a substantial reduction of the steel rebar cages. Several results have been computed with the numerical model using different dosages of macro synthetic fibres, showing that the mass of steel reinforcement could be reduced by 50 and 75 per cent respectively.CITATION:Juhasz, K P, Nagy, L and Winterberg, R, 2014. Full-round numerical modelling of a macro synthetic fibre reinforced tunnel boring machine tunnel in the Shanghai Metro extension, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 477–484 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014