Search Documents

By R. G. Bentsen, D. A. T. Donohue

The cyclic steam injection process has become the most widely applied and most successful thermal recovery technique in use today.1-4 Normally, steam stimulation is repeated several times during the life of a project. The problem is to select the optimum number and size of steam treatments so that the profits realized over the entire life of the project are maximum. Obviously, operating costs rise directly with the frequency and amount of steam injection. Operating efficiency, on the other hand, can be adversely affected if the amount and frequency of stimulation are insufficient. Thus arises a multistage decision problem; that is, a decision must be made at each sub-period (day, for example), as to whether steam should be injected, and, if so, how much. It is desirable that these decisions be made in such a way as to secure maximum net profit before taxes. This can be achieved by dynamic programming. To use dynamic programming, we must be able to predict not only the production rate-time curve resulting from a given stimulation, but also how changes in stimulation policy will affect this curve. In this study, the effect of steam injection on well performance is estimated on the basis of a simple model that takes into account both steady-state and transient flow. Oil production rate is calculated for both types of flow, and the larger of the two values is used. This allows the calculation to change to radial steady-state flow at such time as this mechanism becomes more effective than the transient mechanism. We propose to show how dynamic programming can be used to optimize the steam soak process with respect to net profit. For this, a mathematical representation of the steam soak technique is necessary. A further objective, therefore, is the formulation of a mathematical model capable of realistically simulating the physical process. Oil Production Response Model The advantage of using a mathematical model is its generality and ease of manipulation. However, the model must be an accurate representation of the physical process, for a solution derived from a model can be no better than the model itself. The question now arises as to how well the model should be expected to simulate reality. In general, the simplest model should be tried first, for additional accuracy is apt to require additional cost and time. Also, the search for a high degree of accuracy may yield only greater complexity and difficulty without yielding significantly better results. With this in mind, we kept our model as simple as possible, yet generally representative of the actual physical process. The number of state variables is limited to three, and stochastic variations in the parameters are ignored. As a consequence, use of this model should be restricted to cases in which the underlying assumptions are not severely violated. In

Jan 1, 1970

By F. Keller

SOME PHRASEMAKER has aptly said that nature made aluminum light but research made it strong. Research has been a vital element in the past progress of the aluminum industry and its future growth likewise depends upon the application of the results of research. The role of aluminum products in World War II is well known and this metal will certainly be increasingly important in the postwar world. Some of the principal developments in the war years were in the field of high-strength aluminum alloys. New and stronger alloys were developed which enabled designers to get increased speed and performance in our fighter planes and bombers. The aircraft industry will continue to use these new materials for peacetime passenger and cargo airplanes. High-strength alloys will also find structural applications in trucks, buses, trains, ships, and bridges.

Jan 1, 1946

By D. L. H. Forbes

(New York Meeting, February, 1912.) Introduction.. THE application of the cyanide process to complex sulphide ores for the extraction of their bold and silver is no longer a novelty, but, as an example showing modern tendencies in this direction, the following description of the new milling process at the Lucky-Tiger mine is offered: The extraordinary richness of the ore in the upper workings of this mine made any thought of milling in its early hays seen unnecessary. Its location in an almost inaccessible part of the rugged mountains just south of the Arizona boundary-line, and 60 miles from the town of Douglas, made the expense of bringing in machinery and supplies a very serious consideration. But, after the property had been shipping high-grade ore on mule-back for a few years, there remained in the mine a considerable tonnage of vein-matter that was too low in value to ship, but which it was thought could be milled near the mine at a profit. The first milling-experiment consisted in the installation of Nissen stamps in conjunction with concentrating-tables and Frue vanners, but, as the ore from the upper workings contained most of its silver in the form of cerargyrite, this type of mill was not successful. The proximity of the mine to the great copper-concentrating mills of Cananea and Moctezuma naturally made the influence of copper-milling, ideas felt in the company's next installation. At considerable expense a stage-crushing concentrating-mill, with a capacity of 100 tons per day, was built. This mill was modeled along the lines of the most approved practice in copper-concentrators at that time, the main idea being that crushing by stages in rolls was necessary in order to prevent losses from ?sliming." Largely owing to the fact that, when the mill

Aug 1, 1912

By H. H. Bein

Most western industrial sands are feldspathic and contain feldspars in variahle amounts. A few deposits will show alumina contents of less than one per cent while others will contain over twelve per cent alumina. Some industries are not especially concerned with the amount of contained feldspar but are interested only in color and in size gradations. Other industries, however, are very much interested in alumina content and set up quite rigid specifications as to this content. Several western plants are beneficiating crude sands both to reduce the iron content and to control the feldspar content. At present, most of these plants are using flotation processes for both controls although a few plants do use magnetic separators for the reduction of iron content. Some work has also been done with electrostatic separators for the feldspar-quartz splits. The Sand Division of Del Monte Properties Company, Pebble Beach, California, has been operating a flotation plant for iron removal and the separation of quartz and feldspar since 1950. As mentioned before, control of alumina, especially in the quartz product, is very important. Some users require an alumina content of less than two per cent and others will demand a product of less than one per cent Al2,O3,. The standard Quinolate method for determining alumina is lengthy and time consuming. The HF —H2SO4 evaporation step is especially critical and, if forced, spattering is apt to occur with a resulting loss of sample. Standard procedure is to evaporate to dry ness overnight at a low temperature. Even with forcing under optimum conditions the procerlnre will take two or three hours to complete. A new method has been developed which allows an alumina determination to be made, in 10 or 15 minutes, on a sample of the quartz product as it is being produced. This pocedure, although simply an approximation, has been most helpful in showing whether or not the product being formed is meeting specifications. This procedure has also allowed a great reduction in samples formerly taken and analysed by the orthodox method. Whether a sample assays 1.75% A12O3, or 1.95% .41,0, is not so important as the fact that it is below the allowable maximum of 2.00%. Similar thinking would apply to products required to contain less than 1.00% A1,0,. The step by step procedures for the method are as follows: 1. Collect sample, drain or filter, and dry. 2. Split sample through standard Jones sample cutter to quarter or eighth sample, depending on size of original sample taken, then split down to about 5 grams through Sepor micro-splitter. 3. Screen through 50 mesh sieve (U.S. Series) and reject undersize. 4. Weigh out 2 grams and place in platinum crucible. 5. Etch with 3-5 mls 38.40% HF for 1 minute at room temp. 6. Decant and wash. 7. Stain for two minutes in same crucible with a 1% water solution of Nigrosene dye. 8. Decant and wash well. 9. Dry.

Jan 1, 1961

By J. A. Berger, R. J. Towner

The pjPocesses of polygonization and subgrain growth were followed in slightly stretched 99.99 pct A1 single crystals heated for cumulative times at 400°, 500°, and 600°C. Changes in sub-grain size and boundary angle were determined from measurements on X-ray micrographs. CAHN1, 2 studied polygonization in stretched and heated aluminum single crystals of 99.99 pct A1 using various techniques, including etch pits, Laue patterns, and a slight restretching of heated specimens to reveal small changes in lattice orientation by the direction of new slip lines. He found that kink bands, which had well-defined boundaries lying in a plane perpendicular to the slip direction (at least in the early stages of deformation), formed during stretching. Also, he noted that bending occurred about the <211> axis lying in the (111) slip plane perpendicular to the <110> slip direction. His studies of polygonization were largely confined to the kink bands rather than to the weakly bent matrix regions between bands. The minimum temperature required to bring about polygonization was established at about 450 "C. Guinier and Tenevin used a focusing Laue X-ray diffraction technique to study polygonization in aluminum single-crystal specimens of 99.99 pct purity. Stretching the crystals 5 pct in tension caused a widening of the focused Laue spots. After heating for 4 hr at 450°C, their method revealed no change in the specimen. Above 450°C polygonization was detected and further annealing near 600°C led to subgrain growth. They concluded that the orientation of the crystal relative to the axis of deformation had no marked effect on polygonization. Gay and Honey-combe4 using an X-ray microbeam technique found that polygonization did not occur in a stretched aluminum crystal heated at 250oC, although some decrease in the yield strength occurred. When the temperature was raised to 475oC, the asterism became broken up as a result of polygonization. Honeycombe5 noted that reflections on X-ray mi-

Jan 1, 1961

By William H. Waggaman

CURTAILMENT of the mineral industry as a whole undoubtedly will follow world peace, but the output of certain minerals should pursue a course well above the average on any curve of probable output projected beyond the trends exhibited through 1939. Without speculating on industrial conditions in the pending recomversion period, demand for fluorspar should be greater than before the war because of these factors, introduced by or resulting directly from military necessity: (1) Discovery and development of new deposits. (2) Improved technology in benefication. (3) New and expanded uses for fluorspar and its derivatives. The steel industry has been and continues to be the greatest consumer of fluorspar, and it wag largely to meet the wartime needs for steel that the domestic fluorspar industry has been expanded so greatly. Not only were the search for and development of new deposits of this mineral considered esstinal but the marginal nature of some of the,c- domestic deposits made it necessary to improve mineral dressinc and processing techniques to utilize them

Jan 1, 1945

By Ivan Simon, R. K. McConnell

Anticipating the availability of tiltmeters suitable for use in boreholes, this article proposes a method of using one or more of these meters to determine in situ stress distribution before and after mining operations. Several ways of using relief techniques to measure in situ stresses in rocks have been developed. These techniques, summarized by Merrill,1 involve measuring deformations which take place when a specimen of rock is wholly or partially isolated from the stress field in the surrounding rock. Measurements of rock deformation caused by stress relief from mining operations can, in principle, also be used to estimate in situ stress distributions. Müller2 has mentioned experiments being carried on in Austria with a "deformation indicator" to determine the tilting of holes drilled before a mine opening is made. Similar work using borehole extensometers has been reported by Potts? and Duvall4 has called attention to the possible use of tiltmeters in making these measurements. Considerable attention is now being paid to the use of tiltmeters in detecting rock deformation associated with fault movements, earthquakes, earth tides, etc. The instruments used for these measurements have usually been of the mercury tube, water tube, or quartz fiber type, but because of their large size, and/or fragile nature, such instruments would not be suitable for use in mining stress measurements. Recent instrumentation developments, however, give promise that rugged, sensitive tiltmeters small enough for use in boreholes may soon be available.&apos; In anticipation of these developments, this article presents a number of calculations of the possibility of using one or more tiltmeters emplaced in a drill hole prior to mining operations to determine the in situ stress distribution both before and after a mining operation. Consider point p (x, z) near a tunnel of radius a

Jan 1, 1969

By Paul Billingsley

THE purpose of this paper is a comparison, based on genesis, of the ore deposits associated with the igneous rocks of the central Montana Rockies. Considered separately, without attention to their origin, the orebodies appear to be distributed haphazard, with no fundamental laws controlling their position and character. It is believed, however, that if all the factors be weighed, this apparent confusion will to a large degree disappear. The, first essential to such a comparison is detailed knowledge of the individual mines, as to their geographic position (see Fig. 1), their mineralogical character, and in particular the derivation of their ores.1 The authors of this paper have pursued such an investigation for the past 6 years, and have accumulated a mass of evidence that enables a preliminary correlation to be attempted. It appears that the majority of ore deposits are genetically related to one or another of the igneous

Jan 4, 1917

By E. J. Eisenach, W. E. Jones

SAFETY and industrial hygiene have always been recognized as highly important in company policy, and the co-operative support of the company officials and entire plant personnel has contributed largely to the present success of the Company&apos;s program in this field. Growth has necessarily been slow, and dependent, at times, on trial and error but the program in its present form combines the regulations, working methods, and equipment that have proved their value under actual operating conditions. Every effort is made to keep the program on a practical basis. Continuous experimental work is carried on in conjunction with the health and safety program, with resultant periodic changes for improvement. As a proof of accomplishment, in 1945 the frequency and severity rates for accidents were the lowest in the history of the operation. A full-time safety engineer was employed in 1933 and an assistant safety engineer in 1936. During the following year a stenographer was employed in the office and a safety inspector was added for the mine. During the gradual expansion of operations that was climaxed by

Jan 1, 1946

By F. T. Davis

Many contributors have added to the fund of knowledge in the basic sciences related to mineral dressing during the past year. During 1964, the French edition of the Proceedings of the VIth International Mineral Processing Congress together with discussions was printed. Also, complete Preprints of papers delivered at the VIIth IMPC were published in September1. Over a third of the papers presented at VIIth IMPC dealt with fundamentals. COMMINUTION It has been postulated by Ponceleta that flaws need not exist before a stress is applied but rather the flaws are created at the tip of a propagating crack at a stress well below the theoretical breaking stress.

Jan 2, 1965

By Sam Tour

SOME years ago, the writer described heat checks or thermal cracks that occur in die-casting dies.1 The life of dies was considered in relation to the casting temperature, the material used for the die, and the heat to be absorbed by the die per unit volume of casting made. The mech-anism of the action that results in thermal failure of dies was described. In the present paper the writer proposes to describe some additional observations in regard to heat checking, make one or two suggestions as to the method or methods for further attack of the problem, and give the results obtained on some work carried out along these lines.

Jan 1, 1934

By Marius R. Campbell

Does mine-sampling show the commercial value of a coal, and if so, how should it be done? This question is often asked, but seldom answered. During the past summer, while engaged in securing coal for the Government coal-testing plant at St. Louis, I had an excellent opportunity to obtain information on this subject, and the results seem to furnish an answer to the questions propounded above. Sampling for the Geological Survey Coal-Testing Plant. In organizing the work of the testing-plant, it was decided that coal in car-load lots only would be accepted for testing, also that this coal should be loaded under the immediate supervision of a representative of the plant, so as to be certain that the car-load sample would be representative. As an additional check on the work, two mine-samples were to be collected from each mine visited, and these samples, as well as the sam¬ple from the car when it was received at the testing-plant, were to be carefully analyzed at the chemical laboratory, which was established in connection with the plant and operated under the direction of Prof. N. W. Lord, of the Ohio State University, Columbus, Ohio. Mine-Sanmhling:-Mine-samples were collected with great care by me and my assistants, Messrs. J. Shober Burrows, John W. Groves and Frank W. De Wolf. The dominant idea in the regulations which were adopted for mine-sampling was that it should be done in such a manner that the sample would have the same composition as the commercial output of the mine. .

Sep 1, 1905

By J. Moore, D. Gault, R. V. Lugn

Impact of small projectiles with velocities between 0.9 and 7.3 km per sec on basalt produce craters chiefly by the ejection of fragments. Weight-size distributions of the ejecta are linear for part of the size range of the fragments. Cumulative weight-size distributions of the ejecta from different craters vary because of erratic formation of large fragments and a large percentage of ejecta below 0.1 mm. In the range of velocities studied, the crater depth is approximately proportional to the 0.75 power of velocity of the projectile. This relationship may represent a transition regime between the fluid impact regime and the undeformed projectile impact regime. The volumes per unit of projectile energy of the craters produced are comparable to those reported for lower speed projectile impact and drill bits. An experimental investigation of projectile impact on rock is being conducted jointly by the Ames Research Center of the National Aeronautics and Space Administration and the U.S. Geological Survey. Projectiles are launched with light-gas guns at the Ballistics Range of the Ames Research Center. The craters and ejecta produced in these experiments are being studied by the U.S. Geological Survey. Steel, aluminum and polyethylene projectiles weighing from 0.25 to 0.015 g were accelerated to velocities of 0.88 km per sec (2,900 fps) to 7.3 km per sec (24,000 fps) with a light-gas gun, using hydrogen as the propellant medium. Projectiles impacted the targets normal to plane rock surfaces in an atmosphere of air with a nominal pressure of 25 to 50 mm of mercury. The metal projectiles were mounted in supporting four-piece nylon sabots, which guided the projectiles down the launching tube. After launch, aerodynamic drag acted to separate the sabots from the projectiles. Impact velocities were determined with time measurements and spark photographs of the projectiles in flight. Ejecta were collected in lucite and aluminum containers placed around the target block. A small hole in the containers permitted projectile entry. Impact of projectiles of the size employed produced craters in the rock targets chiefly by ejection of fragments. The craters are small, roughly conical depressions with crushed and intensely fractured rock at the bottoms of the depressions. The ejecta are composed of pieces of the projectile and rock fragments ranging in size from a few tenths of a micron or less to several centimeters in maximum dimension. In this paper, the structural features of the craters, the weight-size distributions of the recovered ejecta, and crater depth and crater volume relationships are described. DESCRIPTION OF CRATERS Typical craters (Fig. 1) produced by experimental projectile impact in basalt are shallow, wide base

Jan 1, 1963

By Open-Hearth Steel

I received a telegram yesterday from Mr. J. H. Nead saying that he regretted circumstances had come up which prevent his attending the meeting, but that arrangements have been made and Mr. T. S. Washburn, of Inland Steel, will act as the Co-Chairman in his stead. We are sorry, of course, that he cannot be here at this conference. We have, therefore, asked Mr. James J. Bowden, chief metallurgist of Republic Steel Corporation, Cleveland, to act as Chairman and Mr. Tom Washburn to act as Co-Chairman. I will turn the meeting over to these gentlemen at this time.

Jan 1, 1940

By E. A. Swedenborg

The unit agreement for the Wertz Dome field, Wyoming, was approved by the Acting Secretary of the United States Department of the Interior on November 4, 1937, effective on December 1, 1937. The stated objectives of the agreement are to conserve and put to beneficial use all oil and gas produced; to make possible a uniform withdrawal of oil and gas in order to maintain equalized reservoir pressures; to provide for an orderly determination of the structural features of the productive horizons; and to permit the injection of gas for pressure maintenance. The purpose of this paper is to show by a discussion of the problems involved and the engineering practices employed by the unit operator, how well the objectives of the unit agreement have been accomplished in the development and production of oil and gas from the field. HISTORY AND DEVELOPMENT The Wertz Dome oil and gas field is located 88 miles southwest of Casper and 38 miles north and westerly from Rawlins, Wyoming. It is served by a state secondary oiled road connecting with U. S. Highway No. 220 at Lamont, a distance of 3 miles from the field. It has been a producing field for 27 years, first as an important producer of gas and more recently of oil. The Producers and Refiners Corp. completed Well No. 1, NE1/4SW1/4 sec. 7, T. 26 N., R. 89 W., the first productive well in the field, in September. 1921, in the Muddy sandstone of Upper Cretaceous age, at a depth of 3435 feet for an initial production of 42,000,000 cu. ft. of gas per day. In 1922 pipe lines were laid to Casper, Wyoming, for supplying fuel to the Standard of Indiana refinery, &apos;the adjoining town of Mills. and the Producers and Refiners Corp. pump station No. 6 in Mills; and to Parco (now Sinclair), Wyoming, for supplying that refinery with fuel. The gasoline content of the gas was extracted in an absorption plant located near the town of Mills. No compressors were used as the line pressure was sufficiently high to flow the gas through the absorbers. As high as 30,000,000 cu. ft. of gas per day were treated in the plant extracting 6000 gallons of gasoline. In September 1937, the pipe line was discontinued and the plant was dismantled at which time 61,000,000,000 cu. ft. of gas had been produced from the seven Muddy, Cloverly, and Sundance gas wells drilled in the field. Of this volume of gas 800,000,000 cu. ft. were produced from the Frontier formation, 34,200,000,000 cu. ft. from the Muddy sandstone, 24,000,000,000 cu. ft. from the Cloverly, locally called Dakota, and 2,000,000,000 cu. ft. from the Sundance formation. The pipe line was discontinued because of the near depletion of the gas reserves in Wertz and nearby fields, and hecause of the local field requirements demanding the retention of the remaining gas reserves. In December 1936, the Sinclair Wyoming Oil Co. completed Well No. 10, SE1/4NW1/4 sec. 7. T. 26 N., R. 89 W., at a depth of 5886 feet. as the first Tensleep sand producer with an intial of 1700 barrels of oil per day. The well was originally drilled only 14 feet into the sand and in August 1939 was deepened to a depth of 6161 feet, 289 feet in the sand, and the daily produe tion increased to 8350 barrels of oil. In February 1948 Well No. 22, SE1/4 SE1/4 sec. 1. T. 26 N., R. 90 W., was deepened from the Tensleep to the Basal Amsden sand and completed at a depth of 6635 feet for an intial of 600 barrels of oil per day in the Basal Amsden. In April 1948, Well No. 2. SW1/4 NE1/4 sec. 1, T. 26 N., R. 90 W.. was deepened from the Tensleep to the Madison limestone and was completed at a depth of 7193 feet for an intial of 1145 barrels of oil per day in the Madison. Well No. 26, SE1/4SE1/4 sec. 1, T. 26 N.. R. 90 W., was deepened from the Ten-sleep to the Cambrian and in October 1948 it was completed in the Cambrian for an intial of 277 barrels of oil per day. GEOLOGY AND PRODUCTIVE ACREAGE The surface is Steele shale of Upper Cretaceous age, covered in part by gravel beds. The topography of the field is that of a rolling hill with a steep draw or gulch along the northern edge of the field. The Steele shale lies conformably on the lower formations as

Jan 1, 1949

By E. A. Swedenborg

The unit agreement for the Wertz Dome field, Wyoming, was approved by the Acting Secretary of the United States Department of the Interior on November 4, 1937, effective on December 1, 1937. The stated objectives of the agreement are to conserve and put to beneficial use all oil and gas produced; to make possible a uniform withdrawal of oil and gas in order to maintain equalized reservoir pressures; to provide for an orderly determination of the structural features of the productive horizons; and to permit the injection of gas for pressure maintenance. The purpose of this paper is to show by a discussion of the problems involved and the engineering practices employed by the unit operator, how well the objectives of the unit agreement have been accomplished in the development and production of oil and gas from the field. HISTORY AND DEVELOPMENT The Wertz Dome oil and gas field is located 88 miles southwest of Casper and 38 miles north and westerly from Rawlins, Wyoming. It is served by a state secondary oiled road connecting with U. S. Highway No. 220 at Lamont, a distance of 3 miles from the field. It has been a producing field for 27 years, first as an important producer of gas and more recently of oil. The Producers and Refiners Corp. completed Well No. 1, NE1/4SW1/4 sec. 7, T. 26 N., R. 89 W., the first productive well in the field, in September. 1921, in the Muddy sandstone of Upper Cretaceous age, at a depth of 3435 feet for an initial production of 42,000,000 cu. ft. of gas per day. In 1922 pipe lines were laid to Casper, Wyoming, for supplying fuel to the Standard of Indiana refinery, &apos;the adjoining town of Mills. and the Producers and Refiners Corp. pump station No. 6 in Mills; and to Parco (now Sinclair), Wyoming, for supplying that refinery with fuel. The gasoline content of the gas was extracted in an absorption plant located near the town of Mills. No compressors were used as the line pressure was sufficiently high to flow the gas through the absorbers. As high as 30,000,000 cu. ft. of gas per day were treated in the plant extracting 6000 gallons of gasoline. In September 1937, the pipe line was discontinued and the plant was dismantled at which time 61,000,000,000 cu. ft. of gas had been produced from the seven Muddy, Cloverly, and Sundance gas wells drilled in the field. Of this volume of gas 800,000,000 cu. ft. were produced from the Frontier formation, 34,200,000,000 cu. ft. from the Muddy sandstone, 24,000,000,000 cu. ft. from the Cloverly, locally called Dakota, and 2,000,000,000 cu. ft. from the Sundance formation. The pipe line was discontinued because of the near depletion of the gas reserves in Wertz and nearby fields, and hecause of the local field requirements demanding the retention of the remaining gas reserves. In December 1936, the Sinclair Wyoming Oil Co. completed Well No. 10, SE1/4NW1/4 sec. 7. T. 26 N., R. 89 W., at a depth of 5886 feet. as the first Tensleep sand producer with an intial of 1700 barrels of oil per day. The well was originally drilled only 14 feet into the sand and in August 1939 was deepened to a depth of 6161 feet, 289 feet in the sand, and the daily produe tion increased to 8350 barrels of oil. In February 1948 Well No. 22, SE1/4 SE1/4 sec. 1. T. 26 N., R. 90 W., was deepened from the Tensleep to the Basal Amsden sand and completed at a depth of 6635 feet for an intial of 600 barrels of oil per day in the Basal Amsden. In April 1948, Well No. 2. SW1/4 NE1/4 sec. 1, T. 26 N., R. 90 W.. was deepened from the Tensleep to the Madison limestone and was completed at a depth of 7193 feet for an intial of 1145 barrels of oil per day in the Madison. Well No. 26, SE1/4SE1/4 sec. 1, T. 26 N.. R. 90 W., was deepened from the Ten-sleep to the Cambrian and in October 1948 it was completed in the Cambrian for an intial of 277 barrels of oil per day. GEOLOGY AND PRODUCTIVE ACREAGE The surface is Steele shale of Upper Cretaceous age, covered in part by gravel beds. The topography of the field is that of a rolling hill with a steep draw or gulch along the northern edge of the field. The Steele shale lies conformably on the lower formations as

Jan 1, 1949

By Edward W. Parker

(Toronto Meeting, July, 1907.) NOTE.-The material from which this paper has been prepared was collected for the U. S. Geological Survey Bulletin, Contributions to Economic Geology, 1906, and appears also, though in somewhat more extended form without illustrations, in that publication. ALTHOUGH the briquetting of coals and lignites has been carried on for many years in Europe, and has reached a particularly high state of development in France, Belgium, and Germany, it has made comparatively little progress in the United States. The causes for the backwardness of the United States in this regard are several, and first among them has been the abundant supply of cheap raw fuel with which the manufactured article has to compete. With our millions of acres of coal-productive territory, from which the product can in most cases be cheaply extracted, it has appeared in many districts more economical to waste the slack or culm, which con¬stitutes a considerable percentage -of the product, than to attempt to save it at the additional expense required for briquetting. It is for this reason that the view in all sections of the anthracite-region of Pennsylvania is marred by the unsightly culm-banks which encumber the ground, and that in some of the bituminous-districts one sees huge piles of unmarketable- slack allowed to burn up in order to get rid of them. When the coal is of a coking quality, or when the slack can be used for steaming-purposes, these losses are not sustained, but many thousands of tons of what might be converted into usable fuel have been wasted every year simply because of the increased expense involved in its preparation.

Sep 1, 1907

The Role of the Drilling Contractor BY FERRIS E. SAINSBURY Ron Haxby, Occidental Minerals What is the best method for drilling a 12-in. diam hole to a depth of 1200 ft and maintaining the deflection within 25ft from vertical? Ferris Sainsbury: In order to drill a 12-111. hole down to 1200 ft, In most places you would have to employ a rotary tricone bit With a down-the-hole hammer, I expect by that depth significant Inflows of water would be experienced Even with foams, we would not be able to get the water out of a hole of that diameter So the down-the-hole tricone method of drilling would be best. To keep it straight, we would probably employ the largest square drill stem compatible with the diameter of the hole. Ron Haxby: Is it common in drilling contracts to put in a vertical hole clause? Ferris Sainsbury: You can put in the vertical hole clause Ron Haxby: Does it cost more? Ferris Sainsbury: Normally, if the hole deviates, the driller can correct it with deflection wedges and will charge it back to you at cost, plus 10% or somewhere along that range Any drill hole has a tendency to go perpendicular to the dip, and there are times when stabilization systems are not successful in preventing the hole from turning into the dip of the formation. The only solution, in this situation, is to go in with an oriented wedge and kick the hole back out.

Jan 1, 1979

By AIME AIME

A REQUEST for information as to the details of activities of the Engineering Council was made by the Joint Conference Committee for the benefit of the new American Engineering Council. , This request was complied with, and the scheduled reply so succinctly sets forth the activities of the old Council as well as the scope of possible activities of ,the new Council, about whose efforts there has been much discussion, .that it&apos; is given herewith in full, except the &apos;budget which is summarized.

Jan 1, 1920

THERE have been two important accomplishments of the Truman administration; the Hoover Commission report on inefficiency and waste in government and the report of the Paley Commission on the natural resources of the United States. Both reports are in the interest of the American people and should transcend the boundaries of political parties. Both reports are starting points for the formulation of policies which must be continuously revised to meet changing conditions. Regardless of the outcome of the election the principles embodied in these two great documents must be kept alive. The Paley report is right in our own bailiwick of mineral raw materials and it behooves us to study it carefully as our responsibility to posterity. To those in the mining industry who have limited their field of observation to moving rock or to metal prices it may come as a surprise that our production of such staples as copper, lead, and zinc has fallen behind increased requirements to the point that substantial tonnages must be imported. Iron ore is next on the list and everybody knows that such metals as tin, tungsten, chromium, manganese, nickel, and cobalt are imported almost exclusively. The crisis in raw materials pointed up by the Paley report has been reported annually by Elmer Pehrson and others to small gatherings at the Mineral Economics Division sessions at the Annual Meeting for as long as we can remember. In September 1949, the United Nations Economic and Social Council held an international resource conference at Lake Success which disclosed these same grave conclusions: - Consumption of raw materials is multiplying at an alarming rate, faster than discoveries or replacements are being made. - Production has been wasteful and utilization lavishly beyond enginee¬ing and practical requirements. - Industrialized nations are depleted and many raw materials consumed by industry are not found in the industrialized countries. - Nations formerly exporters of raw materials are increasingly building their own consuming industries. - Political forces in the world are limiting access to raw materials. The Paley Commission selecting the quarter century, 1950 to 1975, to project raw material requirements for the United States, pointed out obstacles to meeting these requirements, and made recommendations for procurement. It is not important that we disagree that cobalt consumption will reach 344 pct of present, or fluorspar 187 pct when iron and ferroalloys are only expected to increase 75 pct. What is important it that the fabulous appetite of the United States for mineral raw materials has consumed more since World War I than was consumed by the entire world in all recorded history prior to 1914. And, unless the people of the United States are satisfied to remain at their present standard of living (which is unthinkable) this consumption is correctly plotted by the Paley Commission as continuing to expand. If the U. S. is to continue on a course of progress, it must procure raw materials wherever it can at the lowest possible cost. Natural resources are clearly an area in which the broadest cooperation between industry and government must exist to achieve efficient exploitation, economic consumption, and expansion of sources of supply. The message of the Paley report requires action comparable to that of the North Atlantic Pact. Its implication is as significant as military preparedness. It is a world problem. It is a mining engineering problem. Don&apos;t let it die!

Jan 1, 1952