Search Documents

By A. W. Ross, William Marsh Baldwin, T. S. Howald

The related subjects of preferred orientation, directionality in physical properties, and earing tendencies of wrought metal strip have attracted the attention of metallurgists to such an extent that in the past 20 years hundreds of researches have been published on this one general problem. The anisotropy of tensile strength and elongation have been exhaustively studied in their relationship to the occurrence of ears in cups drawn from strip'-~O.~g and, to a lesser extent: yield strength7."-l7 and stress-strain curves'5 have been investigated. Despite the tremendous fund of knowledge thus accrued, no simple quantitative correlation of directionality and earing tendencies has yet been found. In a sense, this is not surprising. The formation of ears in a drawn cup clearly is a special phase of the general study of metal flow; in particular (as will be brought out in the course of this paper), ears are due to anistropy in the rates of deformation of the metal in the radial, circumferential, and "thickness" directions of the original blank. It would be difficult to effect a correlation between caring tendency and a property that may be completely independent of the flow of metal, or at best related to metal flow in an exceedingly complex fashion. Yet, it is this correlation that has been attempted; tensile strength and elongation are attributes of metal rupture. a phenomenon that has quite admirably been shown to be distinct from the phenomenon of metal flow,21 while yield strength and stress-strain

Jan 1, 1946

By William Marsh Baldwin, T. S. Howald, A. W. Ross

The related subjects of preferred orientation, directionality in physical properties, and earing tendencies of wrought metal strip have attracted the attention of metallurgists to such an extent that in the past 20 years hundreds of researches have been published on this one general problem. The anisotropy of tensile strength and elongation have been exhaustively studied in their relationship to the occurrence of ears in cups drawn from strip'-~O.~g and, to a lesser extent: yield strength7."-l7 and stress-strain curves'5 have been investigated. Despite the tremendous fund of knowledge thus accrued, no simple quantitative correlation of directionality and earing tendencies has yet been found. In a sense, this is not surprising. The formation of ears in a drawn cup clearly is a special phase of the general study of metal flow; in particular (as will be brought out in the course of this paper), ears are due to anistropy in the rates of deformation of the metal in the radial, circumferential, and "thickness" directions of the original blank. It would be difficult to effect a correlation between caring tendency and a property that may be completely independent of the flow of metal, or at best related to metal flow in an exceedingly complex fashion. Yet, it is this correlation that has been attempted; tensile strength and elongation are attributes of metal rupture. a phenomenon that has quite admirably been shown to be distinct from the phenomenon of metal flow,21 while yield strength and stress-strain

Jan 1, 1946

By J. Mote, P. Ward Flynn, J. E. Dorn

The effect of strain and strain rate on the critical resolved shear stress for prismatic slip in specially oriented single magnesium crystals was determined over a range of temperatures in an effort to identify the thermally activated strain-rate controlling dislocation process. Below about 450°K prismatic slip was preceded by twinning and fracturing. Above 450°K extensive prismatic slip was obtained followed by fracturing. Neither the Peierls&apos; mechanism nor the dislocation intersection mechanism can account for the observations. The data, however, are in good agreement with the dictates of Friedel&apos;s theory for cross slip to the prismatic plane. PREVIOUS investigations on single and polycrys-talline magnesium have resulted in the identification of the mechanisms of plastic deformation summarized in Table I. The-only well-confirmed mechanisms are {0001}, (1010}, (1011) slip plus (1012) twinning. The other twinning modes were only tentatively established and additional investigations are required to further confirm their operation. As noted in Table I, slip in this hexagonal close-packed metal invariably occurs in the direction of greatest atomic density, revealing that the Burger&apos;s vector for-active slip dislocations is always given by b = a/3<1210>. Slip is easily induced on the basal plane, and recent investigations have shown that the strain-rate controlling mechanism at low temperatures is the thermally activated intersection of the glide dislocations with dislocations threading the basal plane. In contrast, very little is known about prismatic slip. It has been reported to be active at points of stress concentration in polycrystals below

Jan 1, 1962

By Donald O. Rausch, Robert H. Merrill

12.1 -1. Introduction. Problems concerning slopes in soils and rock generally arise in connection with road cuts and open pit mines. The angle at which a slope will safely stand is of major economic importance to both the road designer and the open pit operator. Stable slopes in soils and rock are evaluated through two fundamental approaches, namely, soil mechanics and rock mechanics. The approach selected to make this evaluation depends upon the material in the slope. For the purposes of this chapter, only slopes totally in soil or totally in rock are considered. By definition, soils are unconsolidated accumulations of solid materials produced by mechanical and chemical disintegration of rocks or the accumulation of sediments (28); rock is defined as the hard, compact, natural materials composing the crust of the earth (10). The basic factors affecting slopes in soil or rock are similar, although rock strengths are orders of magnitude greater than soil strengths. In general, the strength of large masses of soil depends upon the texture of the soil, the particle size, cohesion, and resistance to tensile and shear stress; the strength of large masses of rock depends upon the strength of the rock and the defects, such as faults, fractures or joints, that intersect the rock. Further, some of the defects in rock are cemented or uncemented, and may be filled with materials that are strong or weak compared to the rock. In slopes of either soils or rock, the stability is presumed to be a function of the slope height, slope angle, the size of the excavation, and the stresses imposed on the soil or rock by tectonic and/or gravity forces, earthquakes, or other static or dynamic forces. In addition, both soil and rock slopes are affected by static and dynamic water pressures in the pores of soils or permeable rocks or in the defects in the rock behind the slope. Visual observations of slope failures also indicate that both soil and rock can deteriorate with time, and this deterioration may be caused primarily by weathering (27).

Jan 1, 1968

By T&apos Ke, ing-sui

THE subject of recrystallization and grain growth has been much studied and the literature on this subject is numerous. Such studies have been mostly carried out by metallographic examination of X ray methods. Since recrystallization and grain growth involve elementary atomic processes, their mechanism can best be elucidated by a study of some properties which can be readily traced back in terms of such atomic processes. Prior to a detailed quantitative study, however, it is necessary to explore first the possibility and practicability of utilizing any particular property for obtaining the desired information. We have pointed out in a preceding article&apos; that the internal friction of cold-worked metals is extremely high during recrystallization and it drops abru~tlv once the recrystallization is complete. ~reviois work has also shown that the viscosity of grain boundaries in a recrystallized specimen at a given temperature is raised by grain growth.&apos; It seems thus that the measurements of internal friction may furnish a useful tool for the study of the mechanism of recrystallization and grain growth in terms of elementary atomic processes. The purpose of this paper is to report results of a study along this line. We will demonstrate that the internal friction method does give results in agreement with those furnished by conventional metallographic examinations. Once such a correlation has been established, we will be in a position to take further steps to achieve new information which cannot be achieved by conventional methods. The measurements of internal friction were made using apparatus and procedures similar to those used in the preceding article. All the measurements were made under such a small stress level that the internal friction is independent of stress level. The frequency of vibration is, unless mentioned otherwise, about one cycle per second in all cases. Internal Friction and Recrystallization Complete Recrystallization Temperature: Fig. 1 shows the internal friction curve during annealing of a few metals: aluminum, alpha brass and iron. These curves were determined in the following manner. In the curve for aluminum, internal friction measurements were performed upon. 99.991 aluminum subjected to 95 pct reduction area. The internal friction was first measured at room temperature. The specimen was then annealed at 50°C

Jan 1, 1951

By William Kent

ABOUT a year ago, the writer had occasion to assist Mr. John L. Gill, Jr., of the Pittsburgh. Car-wheel Works, in making a trial of his new testing machine. A piece of Bessemer steel, of about .34 carbon, was used as a test-piece, turned to a sectional area of one square inch for a length of five inches between shoulders, and pro¬vided with large round heads, which were fitted to what is called the " Wade grip." Measurements of elongation, accurate to , 1/10000 of an inch, were made by a special apparatus containing two micrometer screws, with electric contact attachment. The machine was operated by hand-power. Readings of elongation were taken at each increment of 2000 pounds stress per square inch, up to 44,000 pounds, the elongation corresponding to the latter figure being .0088 inch. The elongations up to this point remained almost exactly proportional to the stresses, the strain diagram, as shown on the Plate, from the origin to the point A, being a straight line (the deviation of no observation from the straight line being greater than .0002 inch). There being no indication of an approach to the elastic limit, the attendant at the hand-wheel and scale-beam was told to proceed as usual and move the poise forward 2000 pounds, or to 46,000, and turn the wheel until the beam was balanced. Noticing that the beam did not rise in the usual time, and that the elongation was increasing rapidly, the writer called to the attendant to stop turning the hand-wheel and to push the poise backwards until the scale-beam balanced. Instead of balancing at between 44,000 and 46,000 pounds, as was expected, it balanced at 40,000 pounds, and the elongation had increased to .0343 inch (or more than four times that recorded at 44,000 pounds), as plotted at the point B, the dotted line between A and B showing the supposed course of the strain diagram between these two points. Immediately upon recording the elongation the writer said to Mr. Gill, who was standing alongside: "This phenomena is without a parallel in my experience, and I know of but one way to account for it. The piece must actually be broken in its interior, through a flaw or weak portion of the metal. The test-piece is now equivalent to a tube, with

Jan 1, 1880

By R. D. Carnahan, J. E. White

ThE use of strain gages in the measurement of microplastic behavior of materials is well-known.&apos;-3 Recently it has been suggested that similar techniques might be useful for determining stress relaation. It is the purpose of this report to comment on the use of strain gages in the measurement of strains in the vicinity of 10"6. We will also discuss observations of an anomalous anelastic behavior apparently associated with small temperature changes, which accompanies the unload portion of a load-unload microstrain test. The key to successful strain determinations at levels below 1 pin. per in. is a good gage-mounting technique and either precise ambient temperature control or a set of matched temperature-compensated gages. The importance of good mounting cannot be overemphasized, for example, as in the use of Eastman 910 contact cement. If the cement layer is not sufficiently thin and properly hardened, it is possible to observe anomalous negative stresses when small loads are removed, which relax back to zero in an orderly way with time. Such anomalous behavior, thought to be due to gage bonding, has been reported in microstrain experiments by Thomas and verbach&apos; who observed a negative strain of -3 X lo-&apos; upon unloading. This kind of behavior severely limits the over-all strain sensitivity which can be achieved in such tests. The relaxation of a small positive strain subsequent to unloading in a load-unload experiment is quite normal, however, and is to be expected. The occurrence of an apparent negative strain is also encountered in those instances where the elasticity of the bonding cement is exceeded—for example 0.5 pct or 5000 pin. for cured Eastman 910. An elastic strain of this magnitude can be encountered during load-unload type testing particularly in higher-strength materials (-150,000 yield strength). During the course of microplasticity studies on pure nickel and nickel alloys,&apos; the authors have made the following observation. In a four-point bending test, two active gages are mounted one on each side of the beam as arms R1 and R z of a conventional strain-gage bridge circuit shown in Fig. l(a). This technique provides two advantages: the sensitivity is doubled because R1 and Rz experience opposite strains and temperature compensation is provided automatically because any ambient temperature change would cause both gages to see a strain of like sign whose signals would cancel in the circuit.

Jan 1, 1964

By Emory Kemler

The problem of determining the most desirable operating conditions of an oil-well pumping unit or rig front, the selection of the proper material and size of sucker rods, and the design of a pumping unit require that sucker-rod loads be known with a reasonable degree of accuracy. The segregation of rig losses, the proper selection and operation of prime mover and reduction unit, and the analysis of the operation of subsurface equipment require a knowledge of polished-rod horsepower. The investigation of such problems as the instantaneous stresses set up in a pull-rod line or backside crank installation when the well is suddenly hooked on, a study of such problems as the effect of anchoring the tubing on rod load, tubing stresses and rod horsepower, and an analysis of the effect of subsurface equipment on rod loads make it necessary to have a dynamometer that is rugged, which can follow the sudden changes in load without any lag or damping effect, which will record the load in its true position with respect to polished-rod movement, and which will give a card large enough to allow the desired effects to be measured accurately. The inadequacy of the spring or fluid-pressure type of dynamometers has been covered in detail1. The data given show that dynamometers of the spring or fluid-pressure type exert a damping action on the peak loads and the inertia and friction of their load-indicating mechanism introduces a phase lag in recording the load. A dynamometer of that type will not give the load in the correct amount and will not record it in its true position with respect to stroke or time. New Type of Dynamometer Fig. 1 shows a magnetic strain-gage type of dynamometer, to be described in this paper. The strain gage A is used for measuring the load in the polished rod, a washer B and knife edge C take care of initial misalignment and reduce bending in the compression tube of the strain gage. The complete instrument can be transported in the carrying case E.

Jan 1, 1935

By James Howard

ON Aug. 25, 1911, a rail failed on the Lehigh Valley Railroad, causing a disastrous wreck. The surface of the fracture was in a plane at right angles to the length of the rail. There was a dark-colored, oval spot on this surface, located on the gage side of the head, representing the part of the rail which was the first to fracture. The nucleus of this spot showed that the fracture had an interior origin. Other fractures of this kind, the peripheries of which had not reached the surface of-the rail, presented surfaces having a silvery luster. The darkened surface of the present fracture was caused, doubtless, by the air having had access to it. This fracture was recognized as a fatigue fracture, of a modified type, its interior origin having been due to a component in the rail which is not usually present in cases of fatigue fractures. The metal next the running surface of the head of the rail was in a state of internal compression, this being the component not commonly met with in other cases, and which caused the fracture to have its interior origin. For the purpose of giving this modified type of fatigue fracture a specific name, for identification, the term "transverse fissure" was applied. No mystery was thought to attach to its formation, or to its development. The explanation of its occurrence was obvious in the light of common knowledge upon the behavior of steel under repeated alternate stresses. By reason of the state of internal compression at the running surface, the maximum tensile stresses in the head, under bending loads, were along an interior element. Here the tensile strains were higher than in the fibers more remote from .the neutral axis. Under such conditions the fracture of the rail would be expected to have an&apos; interior origin. A discussion of the subject of transverse fissures essentially becomes a discussion of fatigue fractures, since they are identical. The descriptive term employed, merely for the identification of this type of fatigue fracture, had the appearance of creating alarm. Apprehensions arose that a new phenomenon in the physical properties of steel had presented itself, the explanation of which was sought in every

Jan 11, 1917

By J. D. Lubahn

The Bauschinger effect, or rounding of the corner of the stress-strain curve upon reloading, represents a temporary apparent softness that is more pronounced at large strains than small and for complete unloading than for partial unloading. Interrupted creep tests on copper exhibit a similar temporary softness (high creep rate) upon reloading. The fact that the strainwise dying-out time of these effects is the same in both tensile and creep tests shows that they are related. Thus, the term Bauschinger effect appears to embrace behavior following partial or complete unloading and reloading in addition to behavior following reversed loading. It is suggested that the term may properly apply also to certain creep behaviors following a small load decrement. INTERRUPTED tensile tests at low temperatures show1 a rounding of the corner of the stress-strain curve for reloading, which indicates a temporarily low deformation resistance. In the absence of recovery, the curve soon rises to the value that would have prevailed if the test had not been interrupted. The rounding of the reloading tensile curve has sometimes been referred to1 as the Bauschinger effect, although the term is more commonly applied to low deformation resistance in compression following tensile prestrain. The unusually broad usage of the term Bauschinger eflect in ref. 1 seems justified by the obvious interconnection of the various behaviors to which it has been applied.&apos; In fact, the following discussion will indicate that still broader usage might be desirable. The Bauschinger effect is common at room temperature but apparently disappears at higher temperatures.2 Interrupted creep tests and tensile tests were made on certified OFHC copper (nongaseous impurities exclusive of silver were 0.004 pct), cold drawn 84 pct to ½ in. diam, and annealed at 600" (about 0.025 mm grains) or 850°C (about 0.2 mm grains). The tests were made in standard creep or tensile machines, using an O.S. Peters microformer-type extensometer or, for the small plastic strains, a special arrangement employing General Electric magnetic gage heads.&apos; Interrupted creep tests at room temperature show3,4 an initial softness after reloading, manifested by an initial creep rate that is higher than that which would have prevailed if the test had not been interrupted. Fig. 1 shows some typical examples. This effect is apparently temporary (as is that in tensile tests): in four of the five tests shown, the log rate vs strain curve becomes parallel to an

Jan 1, 1956

By William Kent

About a year ago, the writer had occasion to assist Mr. John L. Gill, Jr., of the Pittsburgh Car-wheel Works, in malting a trial of his new testing machine. A piece of Bessemer steel, of about .34 carbon, was used as a test-piece, turned to a sectional area of one square inch for a length of five inches between shoulders, and provided with large round heads, which were fitted to what is called the " Wade grip." Measurements of elongation, accurate to 1/10000 of an inch, were made by a special apparatus containing two micrometer screws, with electric contact attachment. The machine was operated by hand-power. Readings of elongation were taken at each increment of 2000 pounds stress per square inch, up to 44,000 pounds, the elongation corresponding to the latter figure being .0085 inch. The elongations up to this point remained almost exactly proportional to the stresses, the strain diagram, as shown on the Plate, from the origin to the point A, being a straight line (the deviation of no observation from the straight line being greater than .0002 inch). There being no indication of an approach to the elastic limit, the attendant at the hand-wheel and scale-beam wits told to proceed as usual and move the poise forward 2000 pounds, or to 46,000, and turn the wheel until the beam was balanced. Noticing that the beam did not rise in the usual time, and that the elongation was increasing rapidly, the writer called to the attendant to stop turning the hantl-wheel and to push the poise backwards until the scale-beam balanced. Instead of balancing at between 44,000 and 46,000 pounds, as was expected, it balanced at 40,000 pounds, and the elongation had increased to .0343 inch (or more than four times that recorded at 34,000 pounds), as plotted at the point B, the dotted line between A and B showing the supposed course of&apos; the strain diagram between these two points. Immediately upon recording the elongation the writer said to Mr. Gill, who was standing alongside: "This phenomena is without a parallel in my experience, and I know of but one way to account for it. The piece. must actually be broken in its interior, through a flaw or weak portion of the metal. The test-piece is now equivalent to a tube, with

Jan 1, 1880

THE morning session on non-metallic minerals was opened briefly by the chairman, Oliver Bowles, giving the usual instructions and then turning immediately to the introduction of the speakers. "Min-ing and Preparation of the St. Peter Sandstone in&apos; Arkansas" by D. D. Dunkin was first presented by W. M. Weigel, mining technologist for the Missouri Pacific R. R. The paper covered a discussion of the geology of the sandstone, correlating it with the sand-stones at Klondike, Mo., and at Ottawa, III. Its physical appearance, structural characteristics and thickness; the mining methods, blasting, loading, haulage and classification were taken up. A series of slides aided in clarifying the details. The discussion consisted of questioning Mr. Weigel on operating details. The second paper, "Geology and Mining of Diaspore and Flint Fire-Clays of Missouri," written by H. S. McQueen, geologist with the Missouri Bureau of Geology and Mines, and C. R. Forbes, professor of mining, Missouri School of Mines and Metallurgy, was presented by Mr. Forbes. It thoroughly covered the geology, stressing the peculiar sink formations in which all diaspore clay deposits of the region occur. The crudeness of the mining methods was mentioned and believed justifiable because of the small size of the indi-vidual deposits. It was stated that the diaspore and flint clay deposits of Missouri were confined to an area 60 mi. square and it was found in a survey that the average deposit had dimensions comparable to the fol-lowing: 100 ft. long, 75 ft. wide and 50 ft. deep. The largest deposit found was 800 ft. long. 500 ft. wide and 20 ft. deep. It is estimated that the known reserve of clays is from 750.000 to 1,500,000 tons. Mr. Forbes stressed the fact that in mining clays the major problem is entirely one of sorting. This is done under the supervision of a pit foreman trained to make this classification by eye. The mine-run clays are sepa-rated into diaspore clay ranging in alumina content from 70 to about 85 per cent, first grade Burly clay 00 to 70 per cent, and Flint clay 52 to 60 per cent. Discussion of the paper consisted in questioning Pro-fessor Forbes on labor. cost, haulage, drilling, and geology.

Jan 3, 1928

By O. D. Sherby, J. E. Dorn, C. D. Wiseman

MCLEAN&apos; has shown that the total strain obtained during creep of aluminum polycrystals arises exclusively from the mechanisms of 1) microscopically observable slip, 2) subgrain tilting, and 3) grain boundary shearing. Extensive analyses, however, suggest that the high temperature creep of metal polycrystals is controlled by a single thermal activation process."" These somewhat contradictory observations might be reconciled if it could be shown that the activation energies are identical for each of the mechanisms isolated by McLean. Such identity of the activation energies, of course, would demand that the same unit process controls the functioning of each individual mechanism. Under these conditions the activation energies for creep of single metal crystals and polycrystalline aggregates and for grain boundary shearing should be identical. This paper is primarily concerned with the possible identity between the activation energies for high temperature creep of single crystal and polycrystalline metals. In addition, comparisons will also be made between the activation energies for creep of single crystals and polycrystals with previously reported activation energies for grain boundary shearing.0"8 Materials and Techniques The same high purity aluminum, lead, and tin were used in the creep tests for single crystals and polycrystalline aggregates. Single crystals of aluminum and tin were prepared by the strain-anneal technique, whereas lead single crystals were prepared by growth from the melt. The tensile creep stress was maintained constant by Chalmers-Andrade parabolic-type lever arms. Strains were measured to &0.0002 in. per in. with rack and pinion type extensometers, and temperatures were maintained to within & 0.2"C of the reported values by mercury-thermoregulated resistance-heated silicone oil baths. The previously reported unambiguous technique for determination of the activation energy for creep was employed throughout this investigation.&apos; ." It involves periodic abrupt small changes in temperature during the course of creep, accomplished by rapidly replacing one creep bath at temperature TI by a second bath at T,. The abrupt change in creep rate from i, to & attending the abrupt change in temperature is due exclusively to the change in temperature, since both the stress and the substructure are identical the instant before and the instant after a change of temperature. Therefore, all other factors being identical where AH is the activation energy for creep and R is the gas constant. Results Typical examples of the creep rate vs creep strain data during temperature cycled creep tests of single

Jan 1, 1958

By Richard E. Goodman

Rock slope stability assumes different roles in decision making as a mining venture develops and, accordingly, geological investigations vary in thought and in deed according to the project stage. During exploration, stability questions bear on the decision whether or not to mine, because their resolution affects the cost of mining. During the mine lay-out stage, stability is a key factor in deciding how to mine. Finally, during mine operation, stability affects safety and operating costs, and therefore, pit productivity. Among the many considerations influencing stability, rock mass classification and geological environmental factors count heavily. The rock mass behavioral class depends upon the rock character and its degree of fracturation. The loads on the rock are derived from the environmental factors of initial state of stress and the water regime. Of course, stability is also tied to a host of non-geological factors such as the pit geometry, mining style, relative wealth, philosophy of mine operation, and accident history. METHODS OF STABILITY EVALUATION AND CORRESPONDING INVESTIGATORY TOOLS The purposes of the geological investigation are to identify and evaluate the geological factors influencing stability so that the vital questions can be analyzed. The tools selected for stability analysis reflect the stage of development of the mining scheme and therefore the geological investigations, which must furnish data for the analyses and must vary with the project stage. For exploration and mine planning, the methods of resolving stability questions must meet the need to evaluate numerous parameters in limited time; examples of such methods are stereographic projections (1, 2, 3) charted solutions(4) and simple physical models (5, 6). An investigation program that employs geological mapping tools and aids to mapping, such as geophysics, with relatively few rock tests, is in balance with these analytical methods. First data about the water regime are obtained from observed piezometric levels, and the initial state of stress is queried simply through geological inference and experience. In the layout stage more elaborate physical scale models (7) and perhaps finite element models (8, 9, 10, 11, 12), will be relevant to the design process and therefore much more detailed geological investigation is required. The scale of observation of both rock material and joints will be significantly enlarged and mechanical tests of rock and joint strength

Jan 1, 1972

By R. A. Flinn, John T. Norton

A considerable number of experiments in recent years have definitely established the fact that the internal friction or mechanical hysteresis of a metal under cyclic stress is a property that is highly "structure sensitive." Because of this fact, it has been suggested that an observation of this property, which often is referred to as "damping capacity,&apos;&apos; might be a useful indicator of structural changes taking place when a metal or alloy is subjected to any of a number of metallurgical treatments. Damping capacity is of interest to both engineer and metallurgist, but from a rather different point of view, and the information that each desires from such observations is of a different nature. The metallurgist is in search of various external indications of changes taking place in the interior of a metal; changes which are in themselves not directly observable. Even if the observed phenomenon cannot be explained in fundamental terms, it may be empirically related to certain characteristics of the material and prove of real value in research. Internal friction or mechanical hysteresis occupies such a position, and, although it is not well understood in terms of basic metallic theory, an observation of its changes can serve in a very useful capacity. Of course, there is nothing new in the measurement of damping, but the use of this property in metallurgical research constitutes a vast field, which has received all too little attention. The present work is essentially of an exploratory nature in this field and is an attempt to evaluate the process as a research tool. The phenomenon of age-hardening was chosen as a typical example of a structural change and one method of measuring damping was examined in considerable detail. Methods of Measuring Damping Capacity Many kinds of observations can be made upon a specimen subjected to a cyclic stress from which can be calculated the energy absorbed in

Jan 1, 1938

By R. A. Flinn, John T. Norton

A considerable number of experiments in recent years have definitely established the fact that the internal friction or mechanical hysteresis of a metal under cyclic stress is a property that is highly "structure sensitive." Because of this fact, it has been suggested that an observation of this property, which often is referred to as "damping capacity,&apos;&apos; might be a useful indicator of structural changes taking place when a metal or alloy is subjected to any of a number of metallurgical treatments. Damping capacity is of interest to both engineer and metallurgist, but from a rather different point of view, and the information that each desires from such observations is of a different nature. The metallurgist is in search of various external indications of changes taking place in the interior of a metal; changes which are in themselves not directly observable. Even if the observed phenomenon cannot be explained in fundamental terms, it may be empirically related to certain characteristics of the material and prove of real value in research. Internal friction or mechanical hysteresis occupies such a position, and, although it is not well understood in terms of basic metallic theory, an observation of its changes can serve in a very useful capacity. Of course, there is nothing new in the measurement of damping, but the use of this property in metallurgical research constitutes a vast field, which has received all too little attention. The present work is essentially of an exploratory nature in this field and is an attempt to evaluate the process as a research tool. The phenomenon of age-hardening was chosen as a typical example of a structural change and one method of measuring damping was examined in considerable detail. Methods of Measuring Damping Capacity Many kinds of observations can be made upon a specimen subjected to a cyclic stress from which can be calculated the energy absorbed in

Jan 1, 1938

THERE is probably no phase of basic open-hearth steelmaking that is more of an art and less of a science than mold and pouring practice. It varies widely from plant to plant; consequently it is obviously impossible to set down in detail in this chapter the many ramifications of practice that are now used. The discussion that follows therefore attempts only to give an outline of the more common methods, with examples sufficient to indicate some of the variations in procedure, and to emphasize a few of the many underlying problems that face the open-hearth operator at the pouring platform. MOLD DESIGN Ingot molds are hollow castings of considerable wall thickness. Despite this, non-uniformity in wall thickness should be strictly avoided to prevent the setting up of unnecessary stresses. Molds are cast in various forms, sizes, and shapes depending on the type of steel, and on whether the ingot is to be withdrawn from the mold or the mold from the ingot. The selection of ingot-mold material, which is usually cupola or blast-furnace iron containing approximately 3.5 per cent carbon, 1 per cent silicon, 0.9 per cent manganese, 0.2 per cent phosphorus, and 0.07 per cent sulphur, is governed by numerous considerations that affect mold life. (1) Factors in addition to wall thickness that should be given primary consideration at the foundry are casting skin, shrinkage stresses, and casting temperature. Factors in Mold Design. In use, mold thickness is of greatest importance, for it must be heavy enough to freeze the molten metal rising in the mold and to reduce the temperature of the steel below that of the melting point of cast iron to prevent the inner surface of the mold from melting, which would result in the welding of the ingot to the mold. The skin of an ingot, which solidities immediately upon contact with the relatively cold walls of the mold, must soon become thick enough to contract on the fluid mass and pull away slightly from the sides of the mold. The separation of the ingot from the mold depends entirely on the heat taken up by the mold from the steel.

Jan 1, 1944

By J. Gurland, A. Gangulee

The cracking of silicon particles embedded in an aluminum matrix occurs progressively over the range of plastic deformation of the composite specimen. The fracture probability of the particles increases with increasing particle size and decreasing silicon contents. The crack orientation tends to be perpendiculay to the direction of the maximum tellsile strain. An example of a direct association between matrix slip and particle cracking is shorn. ALUMINUM-SILICON alloys of commercial compositions fail by ductile fracture in three stages:&apos; I) initiation of cracks in the silicon particles, 2) growth of cracks into cavities, and 3) rupture of the aluminum matrix separating the cavities. The present work is concerned with the first stage: the initiation of cracks in the silicon particles. EXPERIMENTAL PROCEDURE Aluminum samples with 2.8, 6.1, 9.6, and 13.2 vol pet Si, respectively, were cast from commercial al- loys. Machined tensile specimens (2 in. gage length) were annealed in air at 1000°F for 100 hr, and then pulled at a strain rate of 0.025 per min. The grain size (average linear intercept) of the aluminum matrix was 0.24 and 1.6 mm in the 6.1 and 13.2 pet Si alloys, respectively. The particle size of silicon in alloys of one composition (6.1 pet Si) was varied by either modifying the castings with 0.15 pet Na or prolonging the annealing time. The average particle size was measured by linear and planar analysis, assuming spherical particles of uniform size. The particle sizes and compositions of all samples are tabulated in Fig. 8, together with the identifying symbols used in the graphs. The respective numbers of broken and unbroken silicon particles were determined from metallographically prepared longitudinal sections by counting a total of approximately 2000 particles per sample. EXPERIMENTAL RESULTS 1) Crack Initiation During Deformation as Function of Composition. Nominal stress-strain curves of four specimens of different compositions, but approximately equal particle sizes, are presented in Fig. 1. The fraction of broken particles, P (no. of broken particles/ total no. of particles), is shown in Fig. 2 as function of true stress and in Fig. 3 as function of nominal strain. The last point of each composition line in Fig. 2 rep-

Jan 1, 1968

By C. Zener, H. Nielsen, D. Van Winkle

THE internal friction of metals has been studied frequently at elevated temperatures.1-4 In most cases it rises rapidly with increasing temperature. The notable exceptions are ferromagnetic materials, and lead.2 This paper describes an investigation of the general features of the high-temperature internal friction of 70-30 alpha brass. EXPERIMENTAL METHOD The internal friction of a metal is a measure of the rate at which it dissipates energy of vibration. The measure adopted here, I/Q, is (I/2p) times the specific damping capacity, a measure commonly used by engineers. In the measurements of this investigation, the stress level was kept so low that the observations were independent of the stress. The general method of making such measurements, and of observing the temperature of the specimen during a measurement, has been described elsewhere.5,6 The driver and detector coils were wound with wire insulated with glass thread, in order to withstand the high temperatures used. In previous work electrical eddy currents in the specimen served as the coupling between the mechanical vibration of the specimen and the electrical circuits of the driver and detector. The high values of the internal friction in the present investigation rendered this coupling insufficient. In order to increase this coupling, pole pieces cut from ordinary telephone diaphragms were attached to the specimen. A mixture of French chalk and water glass proved a satisfactory cement. All measurements were made at the fundamental frequency for transverse vibration, which lay between 600 and 900 cycles per second. SPECIMENS The measurements described herein were made upon a single cylindrical rod of brass, kindly furnished by Dr. Cyril Stanley Smith, of the American Brass Co. This rod was the specimen E of the set of alphabrass rods described in an earlier paper.6 Successively larger grain sizes were obtained by annealing at successively higher temperatures. A slice was cut off one end after each set of measurements. Grain counts were made on each slice by W. E. Lindlief, of the American Brass Co. Nine fields were viewed on each piece, located as shown in Fig. I. Results are given in Table I. The grain size is defined in the usual way; namely, Grain size = I/n ½ where n is the mean number of grains per square millimeter. EXPERIMENTAL RESULTS This paper is concerned exclusively with the part of the internal friction that becomes dominant at high temperatures. It is thus desirable to separate this part of the internal friction from the part that is

Jan 1, 1942

By Arthur G. Levy, Henry M. How

The purpose of the investigation on which this paper is based is to determine whether the structural change which occurs in the slow cooling of steel below the transformation range has an important effect on its engineering properties. We recognize two distinct things which occur in steel when it is brought from above to below the transformation range, first, the transformation proper, that is, the breaking up of the austenite or solid solution of the cementite in the remainder of the iron, and the liberation of its components as undissolved cementite and as ferrite or alpha iron; and second, a structural change consisting in the gradual coalescence of the ferrite and cementite respectively into larger and larger separate masses. Let us distinguish these from each other by speaking of them as " the transformation " and " the structural change " respectively. If the cooling is at all rapid the unevenness of contraction induces severe stress; so that in a sense a slow cooling has a third influence, the prevention of such stress. This transformation from austenite to ferrite plus cementite can complete itself only below the transformation range; and, because this structural change is a change in the structural arrangement of the products of that transformation, it too can complete itself only at temperatures below that range, say below 725°; and of these temperatures it is only those between 600° and 725° that give the metal sufficient mobility to permit this structural rearrangement to progress with ally rapidity. The transformation is now known to be rapid, but the structural change is relatively slow. The transformation, the liberation of the dissolved cementite from the state of solution in the austenite to a free state, leaves the steel structurally in the

Jan 1, 1913