Search Documents

By William J. Craig, Harold L. Walker

INDUSTRY has for many years recognized the dependence of certain mechanical and physical properties, as well as workability, upon grain size variations in brass. Although the dependence of properties upon grain size has been recognized there are not many instances where a planned program of testing has been conducted and where the only intentional variable has been grain size. In particular the literature is limited with respect to the effect of grain- size on the endurance limit, though there are many industrial applications where the brasses are subjected to cycles of repetitive stresses. LITERATURE A number of the physical and mechanical properties of a given brass sheet, in the annealed condition, will depend upon: (I) The ready-to-finish grain size before final rolling, (2) the percentage deformation by cold working, and (3) the time and temperature of annealing, The first and second variables affect the recrystallized grain size, and the third variable affects the coalesced grain size. Gibbs1 has shown the effect of two different ready-to-finish grain sizes upon the tensile strength and hardness of deep drawing brass strip after a definite amount of cold rolling. The smaller the ready-to-finish grain size, the higher the tensile strength and hardness, but with lowered ductility, Gibbs also demonstrated, for a given time and temperature of anneal, that the tensile strength, hardness, and elastic limit are higher for the smaller ready-to-finish grain size, but the elongation is lowered, Townsend and Greenall2 have reported data which show that cold working increases the tensile strength, hardness, and load carrying ability of deep drawing brass sheet under reversed stress. Greenall and Gohn3 have reported data which show that the smaller grain sizes have higher tensile strength and hardness properties, and the data also show that increased cold working increases the tensile strength and hardness properties of deep drawing brass sheet. Kommers4 has reported data for tests of brass of known ready-to-finish grain size, a specific amount of cold reduction, and annealed at different temperatures above and below the recrystallization temperature. Kommers' results indicate that annealing below the recrystallization temperature does not change the tensile strength and hardness properties, but the endurance limit may be increased from 22,000 to 28,000 psi. The increased endurance limit is explained as resulting from the reduction of internal stresses by a stress-relief anneal. Burghoff5 and associates have reported data on creep tests, over

Jan 1, 1948

By R. S. MACPHERRAN

TRENDS in the manufacture and use of cast iron are decidedly toward specialization, alloy iron, and increased strength. Old handbooks list only one kind of cast iron, with a tensile strength of 15,000 lb. Recent A.S.T.M. specifications show that from 50,000 to 60,000 lb. per sq. in. can now regularly he guaranteed. The use of alloy iron, heat-treated iron, and even nitrided cast iron, is rapidly growing and all kinds are improving in quality. Iron for operation at high temperature and corrosion-resisting irons have also been developed. Only a few years ago cast iron was "cast iron," but now there are almost as many kinds of cast iron as there are foundries making it

Jan 1, 1936

By Y. Baskin

Solid-solubility relationships in the Pseudobinary systems UAS-UP, UAs-US. UAS-UC, aid UAs-UN were investigated. The first two systems exhibit complete mutual solubility, whereas the component compounds in the other two systenzs are immiscible. The above information, together with solid-solubility data joy six additional pseudobinary systems , were analyzed for compliance wilh the Hurrze-Rothery rules for rnetallic systems. The relative size difference of the component nonmetal atoms was found to be the dopainant jactor determining the extent of solid solubility between the NaC1-type uranium compounds. The anionic and covalent radii of the nonmetal atoms appear to be inadequate for these systems, but compuled radii based on rare earth compounds yield consistent results for the uranium compounds. THE actinide elements, like metallic elements of the transition and rare earth series, readily form binary compounds with nonmetallic elements of groups IV, V, and VI of the periodic table. Of particular importance are the NaC1-type equiatomic compounds with carbon, nitrogen, sulfur, phosphorus, and arsenic. The uranium members of this family of compounds have high melting points, are essentially stoichiometric, and exhibit various amounts of mutual solubility. Thus, they are of interest for investigating the factors governing the extent of solid solubility. Previous investigators have determined the solid-solubility limits in the pseudobinary systems between the compounds UC, UN, US, and UP. Anselin et a1 .' reported complete miscibility in the system UC-UN. Baskin and shalek 2 and Allbutt et a1.3 reported that UP and US exhibit complete mutual solubility. Shalek and white4 reported partial miscibility in the system US-UC. At 1800°C the maximum solubility of UC in US is 40 mol pct, but that of US in UC is 4 rnol pct. shalek5 found limited solubility in the system US-UN; the maximum solubility of UN in US is 11 rnol pct at 1800°C, while that of US in UN is only 0.3 mol pct. White and askin 6 found very limited miscibility in the system UP-UC at 1800°C. Approximately 7 mol pct UC is soluble in UP, but there is no solubility of UP in the monocarbide. Phase relations in the pseudo-binary system UN-UP were investigated by askin.' Approximately 0.7 mol pct UN is soluble in UP at 1800°C, while UP is immiscible in UN. The present study was carried out to explore the extent of terminal solubility in the systems UAs-UC, UAs-UN, UAs-US, and UAs-UP. This information, combined with existing data, provided a sufficient basis on which to determine the factors governing solid solubility in pseudobinary systems containing NaC1-type uranium conpounds. I) EXPERIMENTAL 1) Materials. The compounds UC and UN were obtained from the Kerr-McGee Corp. and United Nuclear Co., respectively. The US, UP, and UAs were synthesized by reacting finely divided uranium with H2 S, pH3, or AsH3 gas at low temperature (300° to 500°C), followed by homogenization in a vacuum at moderately high temperatures (1400° to 1700°c).8-10 The materials were essentially stoichiometric, with the exception of UC, which exhibited a C/U ratio of 1.05. Oxygen was the major contaminant in these compounds, ranging from 0.05 wt pct in US to 0.30 wt pct in UC, and it was generally combined with uranium to form UO2. The UO2 content in these materials was usually of the order of 1 wt pct, and did not exceed 2 wt pct. Furthermore, no evidence was found for a high-temperature reaction between uranium dioxide and any of the compounds. Chemical analyses of equilibrated compositions in the systems UAs-UP and UAs-US showed that the non-metal atom to uranium ratios averaged about 1.01, and that the oxygen contents ranged from 0.06 to 0.22 pct. However, the small deviations from stoichiome-try or the presence of minor oxygen impurities do not invalidate the conclusions to be drawn from this study. 2) Experimental Procedures. The component compounds in powdered from were blended in the desired proportions for 5 hr in the ball mill that consisted of stainless-steel balls in a plastic container. Chemical analyses indicated very little metallic pickup from the blending operation and virtually no increase in oxygen content. The pellets were pressed in a 0.270-in.-diam steel die under 40,000 psi pressure. One wt pct of stearic acid dissolved in CCl 4 served both as a binder and as a die lubricant. Chemical analyses revealed that the stearic acid left no carbon residue in the sintered samples. The pellets were sintered in vacuum in an unsealed tantalum crucible. The temperature, measured with a calibrated optical pyrometer, was maintained at 1800" + 30°C for 3 hr. This was sufficient time for attaining equilibrium as no change occurred in either the lattice parameters or the sharpness of the X-ray patterns when samples were annealed for longer periods of time. The pellets were cooled with the furnace. Debye-Scherrer powder patterns were taken at room temperature with a 114.59-mm-diam Norelco powder camera and CuKor radiation (CuGI = 1.5405A). Unit cell dimensions were determined from a Nelson-Riley extrapolation to the high-angle reflections. The values for were precise to k 0.001A. 11) RESULTS X-ray and met allographic investigation revealed that complete mutual solid solubility exists in the pseudobinary systems UAs-UP and UAs-US. The lattice parameter vs composition plots, Fig. 1, show a

Jan 1, 1968

By M. Kaufman, D. Rosenthal

IT would be of great importance to our understanding of the phenomena of fracture in metals if a unique relationship could be established between stress and some easily measurable parameter of deformation up to the fracture. It is known that no such relationshir, has been found when the parameter was the mechanically measured strain,' the major part of which is plastic. The present investigation was initiated to determine, among other things, if the X-ray or lattice strain" might be a • For the definition of lattice strain see ref. 2. more suitable parameter. To this end, annealed stress free*' specimens of 61s aluminum alloy were ** Freedom of stress in this particular case means absence of those stresses which can be checked by the technique employed. tested at room temperature and liquid nitrogen temperature (—195OC), by first maintaining the same temperature from the beginning until the end of the test, and then with crossovers from one temperature to the other. Three major factors had to be taken into consideration in designing the specimens and testing equipment. The test setup must allow X-ray pictures to be taken while the specimen is under load (for as much as 2 hr at a given load). Provision must be made for maintaining the test specimen at the temperature of liquid nitrogen as well as at room temperature. In addition, the specimen must be able to rotate to allow the X,ray beam to take in as large a sample of grains as possible, to maintain centering, and to correct for effects of large grains. The final design of the specimen and equipment is shown in Figs. 1 and 2. The specimen and grips are hollow, enabling liquid nitrogen to be poured in through a funnel-container arrangement while the specimen is rotating. The diameter of the specimens at the 2 in. gage section is 5/16 in. with a 3/16 in. diameter hole through the center. A small pilot valve in the lower grip allows a very small stream of liquid nitrogen to escape, thus assuring circulation of the liquid at all times. A low temperature silicone grease-tissue paper packing is used to seal all joints. The specimen is held in the grips by a pin. Spherical socket joints at top and bottom are used to allow for proper alignment. The grips are connected to the thrust bearings by means of plastic couplings to decrease the heat flow. Rotation is accomplished by means of a motor which drives a plastic gear (integral with the lower coupling) through a semiuniversal joint to allow for deforma- tion of the specimen. The torque applied to the specimen is very small. The maximum stress caused by this torque at the highest loads reached was found to be less than 200 psi, The whole unit was mounted in a 10,000 Ib testing machine. An insulation cage was placed around the specimen to cut down air circulation, and consequent frosting of the specimen, and also to reduce radiation and convection heat losses. A narrow window, covered on both sides with a thin plastic materiai allows the X-ray beam to reach the specimen. Thermocouples placed just outside the pilot hole at the lower grip, in the bottom of the funnel container and near the top of the funnel container permitted checks of the

Jan 1, 1955

S. Tandanand, Twin Cities Mining Research Center, U. S. Bureau of Mines As an addition to the fine reviews on drilling presented in the foregoing papers, we feel it would be appropriate to mention briefly some work in this area by the U. S. Bureau of Mines. The Bureau has had under way for several years at its Twin Cities Mining Research Center studies directed toward a better understanding of basic drilling mechanisms. The work includes drillability investigations with diamond rotary, and with percussive drilling systems, as well as fundamental studies of rock behavior under drill bit types of loading. Results of our work to date have contributed the following to the state of the art. MECHANISM OF ROCK FAILURE-Rock fragmentation through use of mechanical energy systems, including drilling systems, consists of two major components-machine and rock. The two components are related to each other by their functional behavior and their resultant motion which the components mutually influence. Forces in the systems are transmitted directly to the bit which in turn induces stresses in the rock. When the induced stresses exceed the strength of the rock, the rock fails resulting in penetration. Rock strength is a function of the forces applied to the rock. Stresses under a drill bit, regardless of bit configurations, are essentially compressive, resulting in a condition where the rock has the highest resistance to failure. The ratio of principal stresses induced under drill bits is an indication of the mode of failure in the rocks. Initially, compressive stresses under the drill bit cause rock to undergo inelastic deformation. The impression observed at the first stage of crater formation under the drill bit shows that rock is no longer elastic. Associated subsurface failure at this stage precedes total rupture which subsequently appears at the rock surface. Thus, explanation of crater formation, by applying theory of elasticity alone, is likely to be over-simplified. ENERGY VERSUS VOLUME OF ROCK REMOVED-Experimental results show that energy per unit volume of rock removed is constant for a particular rock and bit type. Rock offers a definite resistance to penetration, depending on the method of the energy application; this may be defined as the drilling strength of a rock. Energy consumption in a drilling system may be divided into two components: 1) Energy required to move the machine parts; and 2) energy consumption in breaking rock. Component 1 is dependent on the type of the machine. Component 2 is dependent on the strength properties of rock and the efficiency of the bit in rock cutting. The sum of the energy required in both components determines the total energy required in breaking rock. Our work in this area has included consideration of both diamond and percussive drilling systems. PENETRATION RATE-For a drilling rate expression to be useful in predicting field performance, it should include the operating characteristics of the drilling machine. Eq. 37, for example, is simply a statement of the fact that the drilling rate is determined by the power output of the machine (2pNT) and the power requirements to break the rock in the hole (AER). In order to predict the performance of a particular drill and the effect, for example, of the rotary speed, on the drilling rate, R, Eq. 37 must be modified to include the

Jan 1, 1967

By D. J. Schmatz

DISCUSSION OF RESULTS The qualitative correlation between low-temperature ductility and prior high-temperature creep strain in nickel obtained in this investigation confirms the result obtained on high-purity brass by Chen and Machlin. However, the quantitative effect is much smaller in nickel. Comparison can be made on the basis of a prior high-temperature strain that is a certain percentage of the total high-temperature elongation to rupture. In the research of Chen and machlin, the prior high-temperature strain of 1/2 pct equaled 8.5 pct of the total high-temperature elongation at rupture. For nickel, in our experiments, 8.5 pct of 21.2 pct equals 1.8 pct. For eh = 1.8 pct, the loss in ductility in percent equals x 100 = b.5 pct. That is, for equivalent bo Formation of Beta Manganese-Type Structure in Iron-Aluminum-Manganese Alloys D. J. Schmatz IRON-aluminum alloys have gained much interest in the past few years for use as a base material for elevated-temperature alloys because of their excel- high-temperature strain the loss in low-temperature ductility is 8.5 pct for nickel as compared to 60 pct for pure a, brass. It is also interesting to note the observation that in nickel the low-temperature fractures, even at the most extreme high-temperature pre-strain, were partly trans crystalline and partly intercrystalline. In the case of a brass, these fractures were completely intercrystalline. According to the data on the percent of the grain boundary area that is cracked, at 22 pct high-temperature elongation, about 12.5 pct of the grain boundary area does not carry load. Thus, the inter-crack areas are carrying a stress that is about 11 pct higher than the nominal stress. A simple model predicts that the overall elongation, which is primarily the elongation in the bulk of the specimen, will correspond to the nominal stress when the stress in the intercrack area equals the tensile strength. Quantitatively this model predicts the equation The form of this equation will agree with that found if the strain-hardening exponent, n, equals unity. Actually this model is too gross an approximation to yield good quantitative results. The question naturally arises as to whether in ordinary hot-working, such as hot-rolling, intercrys-talline cracks are introduced that affect the low-temperature properties. It appears that the answer is that such a possibility cannot be overlooked, if the hot-working induces tensile stresses at temperatures above the equicohesive temperature and if the material tends to be notch sensitive at low temperature. ACKNOWLEDGMENT This research was supported by the Aeronautical Research Laboratory, Directorate of Research, Wright Air Development Center, United States Air Force. REFERENCES lC. Zener: Fracturing of Metals, 1948, Cleveland, ASM. 'H. C. Chang and N. J. Grant: Mechanism of Intercrystalline Fracture. AIME Trans., 1956, voL 8, p. 544; lownal of Metals, May, 1956. 'E. S. Machlin. CreepRupt ure by Vacancy Condensation, AIME Trans., 1956, vol. 8, p. 106; lownd of Metals, February, 1956 'C. Chen and E. S. Machlin: On a Mechanism of High-Temper at ure Inter-crystalline Cracking, lownd of Metals, July. 1957. p. 829. Alloys lent oxidation resistance. Binary alloys of aluminum in iron are ferritic and consequently have poor hot strength. Alloys of iron-aluminum-manganese were made in an attempt to produce an austenitic alloy containing sufficient aluminum to retain the oxidation resistance of binary alloys of iron-alumi-

Jan 1, 1960

By L. G. Austin

My first contact with industrial milling was during the time I worked in the electricity generating industry in the United Kingdom. In visits to power stations to investigate either deposits in the boiler furnaces or polluting deposits settling around the stacks. I had to check the performance of the vertical coal pulverizers, since poor pulverization aggravated both problems. Naturally, then, when I came to the USA in 1957 to take a PhD in fuel technology at Penn State, I was put to work to review the science of coal pulverization. After this reviewing, I was completely confused. On one hand, there was a well-developed understanding of stress-strain equations, and a rapidly developing knowledge of how stressed, brittle solids fractured, based on the Grifith crack theory. On the other hand, reading in the grinding literature gave me: -Kick's Law, which was clearly not correct in the light of modem fracture theory; -Rittinger's Law, which was also clearly not correct; -Bond's Third Law of Comminution, which was claimed to have something to do with the Grifith crack theory, but where the connection between the two was made by intuitive pseudo-scientific reasoning I could not accept; -the choice of mill motor power for the most common type of coal mill, the Raymond pulverizer, was calculated from the fan power required to move air through the mill. Although I could accept the empirical connection between the two, it made no sense from the point of view of fracture energy. Even today, most books or review chapters on size reduction start from these laws. Incorrect statements abound in the literature, such as "the Hardgrove Index is based on Rittinger's Law," which it is not, "The Bond theory states that work input is proportional to new crack tip length produced in particle breakage," which is not true, etc. My own test work showed that these "laws" did not fit the data for grinding of coal. At about this time, Epstein (1948) and Broadbent and Callcott (1956), following the original work by R.L. Brown (1941) at the British Coal Utilization Research Association, proposed describing breakage as a series of fracture stages. I took their concepts and developed the basic differential equation for a batch grinding process continuous in time, analogous to a batch chemical reactor. Robin Gardner then joined the project and did his PhD on treating batch grinding in the same way as a batch chemical reactor. He found that the basic equation had already been partially derived by Sedlatschek and Bass (1953) in Ger- many. We confirmed experimentally the validity of the equations for describing batch grinding (1962) and formulated the equation describing steady-state continuous grinding in a fully-mixed mill. At about the time this work was published, Gaudin and Meloy (1962) and Filippov (1961) independently published essentially the same equations, but without experimental proof of the validity of the concepts. I will give a brief overview of what these beginnings had led to in the design of mills for size and power, and show some of the results of this more detailed understanding of grinding processes. Concepts of Fracture Mills such as tumbling ball, rod, pebble and autogenous mills and vertical mills such as the Raymond, and E-type, apply compressive stress to lumps or particles relatively slowly. Compressive stress applied to a particle of an elastic brittle solid imparts overall strain energy to the solid and produces local regions of tensile stress, [(Fig. 1)] (Berenbaum and Brodie, 1959).

Jan 1, 1985

By A. M. Adair

The effect of cathodically charging zone-refined iron with hydrogen and the resultant yield stress-grain size relationship has been investigated by tensile testing at -31°C. The resulting Petch plots (using a least-squares analysis) reveal a significant reduction in the slope and an increase in the intercept for specimens cathodically charged with hydrogen, regardless of whether the hydrogen is present during testing or is removed by evacuation. Other than surface blistering, the major effect of cathodically charging this material is to create occasional grain boundary cracks and thus presumably a large number of free dislocations at grain boundaries. These results are consistent with the hypothesis that the slope of the Petch plot is related to the stress required to activate dislocation sources at or near pain boundaries. While there is no significant effect of the presence of hydrogen on the lower yield stress of this material, the ductility is considerably reduced. After hydrogen removal by evacuation, the ductility recovers substantially and almost complete recovery of ductility is experienced by the smaller grain size specimens. THE influence of hydrogen on the mechanical properties of ferritic materials has received much attention throughout the history of the metallurgy profession. This interest has stemmed from the obvious importance of preventing the catastrophic failure of parts in service, and from the desire to determine what mechanism is responsible for the observed behavior. The various mechanisms proposed for hydrogen em-brittlement have been discussed in detail by Tetel-man,'who concludes that a combination of the applied stress and hydrogen pressure within voids best accounts for the many experimental observations reported. From a quite reasonable correlation of the strain aging and delayed-failure behavior of a variety of materials,2-7 Troiano and coworkers are of the opinion that the delayed-failure mechanism (slow strain rate embrittlement as well) is better explained as a lattice effect; solute elements diffuse to regions of high triaxial stress, form uncondensed atmospheres there, and effect a reduction in the cohesive strength of the lattice. Since hydrogen yield points8,9 have been observed in ferritic materials, and since the hydrogen embrittlement process may be related to strain aging, one further contribution to embrittlement could be hydrogen-dislocation interactions which make crack blunting by plastic deformation a more difficult process. The etch" relationship offers a means of comparing the relative ease of initiating and propagating plastic deformation in metals and alloys. In the present study, this relationship was used to compare the behavior of zone-refined iron in three conditions: uncharged, cathodically charged with hydrogen, and cathodically charged with hydrogen and evacuated. These Petch plots and the observed ductility parameters allowed a separation of the effects of the very presence of hydrogen and the act of cathodically charging hydrogen into this material. MATERIALS AND EXPERIMENTAL PROCEDURE An ingot of zone-refined iron was obtained from Battelle Memorial Institute which contained the following (typical) interstitial impurities in ppm: carbon, 10 * 5; nitrogen, 1; oxygen, 22; hydrogen, 0.9. The ingot was cold-reduced to a 1/2-in.-sq cross section, recrystallized 1 hr at 575°C, and then straight-rolled to a thickness of about 0.105 in. Tensile specimens were milled from the strip having a 1-in. gage length

Jan 1, 1967

By A. D. Marlin, A. J. Gentile, E. F. Jordan

Metallurgical changes in SAE 52100 ball-bearing components resulting from overload testing are described. Changes in microstructure, hardness, and resiclctal stresses crre discussed zuitlz re.ference to material cleanliness obtained by various steel-melting practices and are compared with work by otlzer investigators. Evidence is presented to show that the initialion and development of microstruc-tural alterations are characterized by two separate reactions: the appeavance of a "dark etchingJ' constituent, and "gray lines" or a light etclzing constituent. The dependency of these tzvo reactions on material cleunliness, running tirne, and contact stresses is discussed and a failure mode related to material cleanliness and microstructural transformation is proposed. THE study of ball- and roller-bearing contact fatigue has been paced by a strong emphasis on bears ing application performance. Particular attention has been paid to conditions that effect the spalling-type failure that is characteristic of rolling contact fatigue in through-hardened components. Some of the conditions investigated are lubrication and atmosphere,1-3 material characteristics and finish,475 and speed and design fa~tors."~ A typical spalling-type failure is shown in Fig. 1. The arrow shows the motion of the ball relative to the inner-ring race surface. The leading edge of the spall is usually sharper than the trailing edge. The race surface near the trailing edge also shows small dents caused by debris from the spall. In this type of testing very little metallurgical investigation is done on failed bearings. Emphasis is placed on test conditions and statistical analyses of endurance data. More basic work has been done relating micro-structural changes to fatigue performance. Dyer" and Wood, Cousland, and sargant9 have used mostly simple materials, such as single crystals and single-phase polycrystalline specimens, under simple alternating strain to identify a systematic process of fatigue damage. drutowski" was concerned primarily with the relationship between steel structure, contact stress, and energy losses in rolling contact. dones11 and Bush, Grube, and Robinson12 utilized changes in microstructure and residual stress in overload-tested rolling contact elements as a means of investigating the fatigue process. Work is being done on an ASME-sponsored contract,13 using both simple and complex materials, but there is still a long way to go before such theories as pore and void growth in simple structures can be applied to the relatively complex bearing steel microstructure. The purpose of this paper is to report on an investigation into the effect of steel cleanliness on the structural alteration and residual stress changes found in overload-tested ball bearings. Using these results and those of previous investigators, we will propose probable failure mechanisms in both overload- and normal load-tested ball bearings.14,15 PROCEDURE Ball bearings? 3208 size, were fabricated from SAE 52100 steel obtained by five different melting practices. The melting practices, chemistry, and inclusion ratings for the five lots of steel are summarized in Tables I and 11. The nonmetallic inclusion ratings were determined by the Jernkontoret method described in ASTM E45-51 Method A. This technique consists of microscopically examining a series of polished samples taken from specified locations in the ingots, billets, or bars. Each sample is surveyed at XlOO magnification and the inclusion types and sizes are compared to standard fields. Because of the nature of these ratings all values in Table I1 are rounded to the nearest half. The elec-

Jan 1, 1965

By D. C. Ganow, N. J. Grant, I. R. Silver, A. R. Chaudhuri

The structural changes that result when a metal is "cold worked" lead to higher values of yield and tensile strength on subsequent deformation at room temperature. Further it has been shown that the beneficial effects of cold work are, to some extent, maintained even at elevated temperatures. The strength improvements from prior cold work decrease as the temperature is raised and are a function of grain size, amount of cold work, and strain rate (or time of test). If recrystallization occurs during test, the cold-worked material may even show weaker stress-rupture properties than the annealed material. A question that arises is whether there is a significant effect on the subsequent creep behavior if the prior deformation is performed under creep conditions at high temperatures not too different than the test temperature, but at significantly different strain rates and for various amounts of strain. An answer to this question was sought in the work described in the present paper. PROCEDURE Two materials were used in this work, high-purity aluminum and a solid-solution A1 2 pct Mg alloy. The compositions are shown in Table I. The grain size in the two materials was 0.2 to 0.3 mm. The deformation for both the prestraining and for the creep tests was at constant stress. The procedure adopted was to prestrain a specimen to the desired elongation, remove the load, and cool to room temperature rapidly by spraying. the test bar with cold water. The specimen was then placed in a creep machine, held at the test temperature for less than 5 min, and loaded. Less than 15 min was required to bring the specimen to temperature. The creep stress was based on the diameter resulting from the prior strain, and values of elongation at fracture listed in the tables do not include the respective elongations resulting from the prestrain. The choice of the stresses for the prestrain and for the creep tests was made so that the tests could be completed in relatively short times to maximize any effect of prestrain. The specimens had a gage length of 1 in., the pure aluminum specimens having a diameter of 0.150 in. and the alloy specimens a diameter of 0.125 in. For pure aluminum, prestrain was at 400' and 600°F with testing at 500°F; for the alloy, prestraining was at 700°F and testing at 600°F. RESULTS The prestrain conditions for the aluminum and the alloy specimens are shown in Tables I1 and IV. In addition to showing the time required to achieve the desired prestrain, the expected rupture Lives are given which would have resulted had the creep prestrain been continued to fracture. The prestrained and the annealed specimens were then tested in creep to fracture; the temperature and stress for the pure aliminum specimens being 500o F and 1800 psi and for the alloy, 600' F and 3400 psi. The creep curves for the prestrained and the annealed specimens of pure aluminum showed all three stages of creep; hence in addition to the effect of prestraining on the rupture life, it was also possible to determine the effect of prestraining on the minimum creep rate, and on the time and elongation at the end of each of the three creep stages. The results are shown in Fig. 1 and Table 111.

Jan 1, 1960

By F. V. Lenel, G. S. Ansell

The creep behavior of an aluminum -aluminum oxide alloy, A T 400, fabricated by compacting an atomized aluminum powder, extruding the compact, cold working, and recrystallizing the extrusion, was investigated. This alloy has a dispersion spacing of 1 . Previously Ansell and Weertman determined the steady-state creep rate of a recrystallized aluminum-aluminum oxide SAP-type alloy, MD 2100, with a 0.48-p dispersion. This alloy was found to have a steady-state creep rate of less than 10-6 min-1, too small to be measured accurately. By employing a more sensitive method of measuring creep rate, it was possible to determine the steady-state creep rate of AT 400 alloy, which is somewhat faster than that of MD 2100, at a series of temperature and applied stresses. Above a stress of Burger's vector, A = dispersion spacing, u = is a shear modulus) the rate follms an equation of the type: Steady-state creep rate K = A exp. where A is a constant, Q is the activation energy for sey-diffusion, and is the applied stress. At stresses lower than the steady-state creep rate drops off sharply and is no longer in agreement with this equation. This behavior is in good agreement with that predicted by the model for dispersion strengthened alloys in the stress and temperature range investigated. The absolute value of the creep rate is, however, four orders of magnitude lower than that predicted if the normal number of active dislocation sources are assumed to be present. It is concluded that in this SAP-type alloy the usual three-dimensional dislocation network is not present. Instead, short dislocation segments extending from one dispersed particle and terminating at a neighboring particle may act as dislocation sources. With this provision the creep model proposed by Ansell and Weertman reasonably accounts for the creep behavior which was observed. RECENTLY, Ansell and Weertman1 proposed a dislocation model from which they derived creep equations to describe the steady-state creep behavior of dispersion - strengthened alloys. Following Schoeck,2 they assumed that the rate controlling process for steady-state creep is the climb of dislocations over the dispersed particles. In order to verify their creep model, Ansell and Weertman determined the steady-state creep behavior of an aluminum-aluminum oxide SAP-type alloy, MD-2100, in both the fine-grained as-extruded, and coarse-grained recrystallized conditions. Since the grain size was the order of the dispersion-spacing, their model was not applicable for the as-ex- truded alloy. It should, however, be applicable to the coarse-grained recrystallized alloy. The results they obtained were rather unexpected. No meas-ureable steady-state creep was observed for the recrystallized MD-2100 alloy. If their model is correct, and if the second-phase particles act solely to hinder dislocation motion, then some measureable steady-state creep would have been expected. On this basis, they postulated that, in this SAP-type alloy, the main effect of the fine dispersion was to inactivate dislocation sources rather than to hinder the movement of dislocations. In order to understand more fully this unusual creep behavior, and to determine the validity of the model proposed,' the steady-state creep behavior of an aluminum-aluminum oxide recrystallized SAP-type alloy, with a somewhat coarser dispersion spacing, was investigated. The results of this study are presented in this paper.

Jan 1, 1962

By S. J. Burns, W. W. Webb

The dislocation arrangements formed during unsteady propagation of cleavage fractures on (010) planes in LiF have been investigated by high-resolution etch-pit techniques and by X-ray diffraction topogvaphy. In impurity-hardened crystals, cracks propagating in any direction on (010) planes at velocities of about 103 cm per sec are usually accompanied by light plastic deformation which is enhanced wherever the crack is allowed to hesitate. Dislocations with [011] type Burger's vectors are often formed looped around the crack tip. They are dragged along with the crack tips leaving edge dislocations lying nearly parallel with the clearage surface about 5µ from it. These dislocations are easily overlooked since they may initially intersect with the cleavage surface infrequently and later may disappear from the crystals due to image forces during aging at room temperature. Although the plastic work associated with these dislocations is only comparable with the reversible (010) surface energy, an instability in crack propagation appears due to a limit of the velocity with which dislocations can be dragged along with the crack. Transition to a fully brittle nonplastic fracture mode occurs when the crack velocity exceeds the velocity with which dislocations can be moved by the stress field of the crack. TRANSITIONS between brittle and ductile modes of fracture appear to be common processes in the behavior of materials in which the flow stress is close to the stress at which brittle cracks can propagate. High-strength engineering alloys fit into this category and the transition from ductile to brittle modes of crack propagation may be associated with catastrophic failures in these important materials. The methods of theoretical mechanics indicate the geometrical conditions in which these processes may occur but the detailed mechanisms controlling the generation of dislocations in the initiation of the plastic mode and the process by which the loss of plasticity occurs on transition to the brittle mode are not yet clear. Since these mechanisms are not amenable to direct observation in engineering alloys we have chosen a semi-ductile alkali halide LiF as a model system in which to observe transition mechanisms between plastic and brittle modes of crack propagation. Cleavage cracks in this system are known to undergo a plastic-elastic transition at velocities between 103 to 104 cm per secl and dislocation configurations in LiF are amenable to study by optical-microscopic observation of dislocation etch pits2 and by X-ray diffraction topography.3 We have been able to identify a dislocation mechanism responsible for the transition from brittle to slightly plastic modes of crack propagation in LiF. A model based on this mechanism permits calculation of the critical crack-propagation velocity for this transition and indicates the importance of the stress dependence of dislocation velocity in determining the critical crack velocity. Of course, this model cannot be carried directly over to more complex materials but it is quite possible that its qualitative features are generally applicable. Dislocations intersecting fresh cleavage surfaces in LiF were reported by Gilman,4 by Forty,5 and by Wash-burn et a1.6 Such dislocations were construed to have been nucleated where the cleavage crack hesitated or stopped, near stress concentrators, such as cleavage steps, on the crystal face. The loci of such dislocations deposited On the cleavage plane in bands were called "stop lines" or "deformation zones". Gilman, Knudsen, and walshl measured the velocity of cleavage cracks in lithium fluoride by evaporating thin resistive strips on the crystal side and recording

Jan 1, 1967

By R. Grierson, R. N. Parkins

The m.echanica1 properties, at high lzomologous temperatures, of the intermetallic compounds InzBi and Mg17A112 were measured as a .function of temperature, applied strain rate, previous thermal and mechanical history, and composition. Mgl,Al12 was investigated ilz compression, whereas Zn,Bi was investigated in tension. A decrease inflow stress with increasing strain was observed jor both alloys. The results obtained are discussed in terms of the dislocation-multiplication processes in these materials. MANY intermetallic compounds are reported to undergo a brittle-ductile transition at high homologous temperatures.' There is evidence in the literature that some of these compounds exhibit a large yield drop when plastically deformed.'j3 Both of these forms of behavior are shown by the covalent elements germanium and silicon4,5 and also by certain ionic compounds.8 The present work is a study of the deformation, at high homologous temperatures (>2/3 Tm), of two intermetallic compounds, In2Bi and Mg17Al12. InzBi has a disordered hexagonal structure7 (c/a = 0.598) and a solubility range of 32.3 — 33.2 at. pct Bi.8 It has a melting range from 72° to 89°C. Mg17Al12 has an ordered bcc (A12 type)7 structure and exists over the range 50 to 60 at. pct Mg8 with a melting range from 437° to 462°C. We have been unable to find any reference to previous investigations of the mechanical properties of BiIn,. Novikovg has reported that cast samples of Mg17A112 show ductility, when bend-tested, at temperatures above 380°C. EXPERIMENTAL Ingots of In2Bi and Mg17Al12 were melted under an argon atmosphere and cast, in situ, in a graphite crucible. The materials used were of 99.99 pct purity. The alloys prepared contained 66.9 at. pct In in the case of In2Bi and 58.4 at. pct Mg in the case of m17A112. The ingots were homogenized and then extruded. Two-in.-diam Mg17Al12 ingots were extruded at 375°C to give 3/8-in.-diam rod. The rate of formation of this rod was 0.25 in. per min. One-in.-diam InzBi ingots were extruded at 20°C, using a rate of 1 in. per min, to give 1/8-in.-diam rod. In both cases the extruded rod had a recrystal- lized, fine-grain, structure. (For Mg17Al12, d = 11.2 µ; for BiIn2, d = 22 µ.) Mechanical-property determinations were made in a hard-beam machine, in tension in the case of In2Bi and in compression with Mgl7Al12. The tensile tests were on specimens having a gage length of 1.1/2 in. and a diameter of 1/8 in. The compression tests on Ml7A112 were on specimens of 3/8 in. diam by 3/8 in. high and the ends were coated with poly-tetrafluorethylene to minimize friction. RESULTS In2Bi. Fig. 1 shows, particularly at the higher applied strain rates, that In2Bi exhibits a marked yield drop as the deformation increases to about 2 pct, after which the material shows neither hardening nor softening up to 15 pct strain. The magnitude of the yield drop, the stress in the region of flow under constant stress (the stress plateau), and the 0.5 pct proof stress were all dependent upon the applied strain rate according to an expression of the form

Jan 1, 1965

By L. W. Pommier, F. B. Brien

The Rheological properties of pulps are non-Newtonian in character and more than one viscosity parameter is necessary to describe their behavior, therefore, the single term 'apparent viscosity' which has been used in the past may be misleading. The study reported in this paper uses a dimensional analysis based on the Ostwald-de Waele shear stress-rate of shear model for non-Newtonian liquids to develop velocity and resistance equations for falling spheres. An electronic monitoring apparatus was assembled for determining the velocity of metallic bodies as they fall through opaque liquids and suspensions. By means of this apparatus the behavior of the viscosity parameters of the Ostwald-de Waele model and the applicability of the proposed equations were examined for a number of non-Newtonian liquids. The validity of the equations for these liquids was confirmed. Preliminary data collected using solid-liquid suspensions established the validity of the form of the basic equations for these systems. The differential movement of solid particles through solid-liquid pulps and suspensions is very important LO many branches of engineering, such as minerals processing, soil mechanics, ceramic slip processing, oil well drilling-mud technology, materials-handling in pipelines, and many others. There is a dearth of fundamental knowledge on the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. The resistance offered by Newtonian liquids to the movement of free settling spheres is well described for laminar and turbulent conditions by Stokes' and Newton's Laws, respectively. However, problems are encountered when attempts are made to extrapolate these simple relationships into solid liquid suspensions. The rheological properties of pulps are such that they are non-Newtonian in character;'" that is, the applied shearing stress and resulting rate-of-shear are related by non-linear functions, and thus, in the simplest case two viscosity parameters are necessary to describe their rheological properties. For this reason the single term 'apparent viscosity' which has been commonly used to explain the flow resistance of suspensions and non-Newtonian liquids may be misleading. It is realized that a rigorous analysis of the rnechanisms of momentum transport of liquid-solid systems is complex indeed. There are many variables that affect the rheological properties of the systems such as density, size, shape, and surface energy of the suspended solid and density and viscosity of suspending liquid, as well as the solid to liquid ratio. However, it was felt that a useful contribution to the knowledge of the behavior of suspensions could be made by examining the systems in terms of the basic fundamentals of nowNewtonian flow. This has led to the development, by means of dimensional analysis, of velocity and resistance equations, using two viscosity parameters to describe the velocity of penetrating bodies and the flow resistance encountered by these bodies, as they pass through non-Newtonian systems. THEORY In order to examine the effects of the rheological properties of solid-liquid suspensions on the movement of immersed bodies it is appropriate to start with non-Newtonian liquids and develop equations, analogous to those of Stokes and Newton, for laminar and turbulent flow respectively, from which quantitative information may be obtained. Further investigation would then be directed at the complex suspension systems, and the effects of the many variables on the velocity and resistance equations. Liquids are classified on a basis of viscosity which may be defined as the relationship between applied shear stress and resulting rate of shear?-'* Pure single phase liquids composed of small light molecules behave as Newtonian liquids, having a single viscosity parameter since the shearing stress and rate-of-shear are related by a linear function. Bingham plastics are similar but have a yield stress. Of particular importance in our investigation are dilatant (shear thickening) and pseudoplastic (shear thinning) non-Newtonian liquids, with and without yield values.

Jan 1, 1968

By W. V. Green

The creep-rupture behavior of commercial powder-metallurgy tungsten rod is reported for temperatures of 2250°, 2500°, 2700°, and 2800°C, stresses up to 7000 psi, and times up to 4 hr. The temperature dependence and the stress dependence of creep rates are evaluated. Rupture time is fitted to the Larson-Miller parameter and compared to lower-temperature and higher stress results reported by pugh.4 THE tensile strength of single-crystal wire1 and of polycrystalline wire2 have been measured by Goucher. More recently Bechtold3 and pugh4 have studied the mechanical properties of tungsten rod between room temperature and 1200°C. Since tungsten has the highest melting point of all metals, it should retain useful strength to very high temperatures, and should find many applications in missiles, rockets, and so forth. Therefore, the mechanical usefulness of polycrystalline tungsten rod was investigated in the 2250" to 2800°C temperature range by short-time creep-rupture tests. MATERIALS TESTED Creep specimens were machined from 1/2-in. round commercial tungsten rod which was manufactured from powder by cold pressing, sintering, and hot swaging. Purity reported by the vendor was 99.95 pct W. Spectrochemical analyses showed "traces" (less than 0.01 pct) of silicon, iron, and titanium, and "faint traces" (less than 0.001 pct) of calcium and manganese. Carbon content was 30 ppm and nitrogen content was 70 to 110 ppm. No oxygen analysis was obtained. Room-temperature stress-strain tests on the as-received tungsten gave badly scattered results. Threaded end specimens broke at the threads. When these specimens were retested using shoulder grips, the specimens broke at the shoulders. No fractures occurred in the gage lengths. The fracture stresses were: 127,000; 137,000; and 154,000 psi for three specimens which fractured at the shoulders. The microstructure of the as-received tungsten rod is shown in Fig. 1. SPECIMENS USED Fig. 2 shows the two types of creep specimens tested. The threaded-end type specimen, which was used in most tests, had a 3/4-in. gage length and 1/4-in. gage diam. The cone-end specimen, which was used primarily to investigate the effects of a smaller gage diameter and the practicability of the modified grips and specimen, had a 3/4-in. gage length and a 1/8-in. gage diam. In both cases, the gage length terminated at 0.005-in. high shoulders which served as fiducial marks for optical strain measurements. Surface finish on the gage length was 16 µ-in. rms. Creep rates and rupture times were not significantly different for the two types of specimens and were not affected by electropolishing the specimens before testing. TESTING PROCEDURE The constant-load creep-testing machine used has been described by Smith, Olson, and Brown.5 In it the specimen is held vertically by grips of similar material and on the axis of a cylindrical tungsten or tantalum heater-tube. The specimen is loaded by means of the specimen grips, a pull rod (which is sealed to the chamber lid by a vacuum-tight bellows), a mechanical lever system, and hanging dead weights. Both specimen and grips are heated by radiation from the heater-tube, which is heated by its own electrical resistance. An optical system views the incandescent specimen through slits in the radiation shielding and heater-tube. The optical system projects an enlarged image of the specimen gage length on a ground-glass screen. Periodic gage-length measurements are made on this image with two cathetometers. Thorium oxide coatings on the specimen threads or conical end surfaces completely prevented diffusion-welding of specimens to grips, and were used

Jan 1, 1960

By R. A. Graham, R. W. Rohde, J. R. Holland

In a shock wave compression study of a martensitic Fe-30 pct Ni alloy, Graham, Anderson, and Holland' found a region of unusual compressibility extending from a few kilobars up to about 20 kbars. This region was characterized by a continuously decreasing shock wave velocity with increasing stress. In this note, we report the results of a study initiated to determine the source of this unusual compressibility. In earlier shock-loading experiments on martensitic Fe-30 pct Ni, Loree et a1.' determined that a phase change occurred at about 80 kbars. Subsequently, Bowden and elly found that samples of a similar material shock-loaded at about 100 kbars experienced a martensite-to-austenite transition. Their crystal-lographic analysis showed the transition was a direct reversal of the established martensite system to the austenite phase. The shock loading in the present experiments was accomplished by precisely controlled plane impact between two discs of the sample material. This configuration created a state of uniaxial strain in the two the front of a projectile which was accelerated to various velocities. Planarity between the impacting discs was controlled to 5 x 10-4 rad, and impact velocities were measured to 0.5 pct. From a knowledge of the Hugoniot relationships of the material and the impact velocity, the shock-wave stress can be calculated. Samples were shocked at 18, 50, 70, and 100 kbars. The specimen discs shocked at 18 and 50 kbars were instrumented with quartz gages to observe the stress time profile. A more detailed description of the experiment has been given previously.4 The shock-loaded specimens were recovered intact by decelerating them in a catcher filled with soft wood. Discs of Fe-30 pct Ni nominally 12.7 mm thick and 64 mm in diam were cut from bar stock. Chemical analysis of the material provided the following composition in weight percents: 29.5 Ni, 0.50 Mn, 0.21 Si, and 0.10 C, with traces of Cr, Cu, Mo, Al, and Co. The discs were austenitized at 650° C for 2 hr at a pressure of less than l0-' torr, and furnace-cooled. Martensite was then produced by quenching the discs at -196" and holding 168 hr. The initial martensitic structure formed is shown in Fig. l(a). Typical microstructures of samples shock-loaded at 18 and 100 kbars are shown in Figs. l(b) and l(c). The banded structure with the austenite regions running parallel to the shock propagation direction was characteristic of samples shock-loaded at all stresses. No such banding was found in samples that were not shock-loaded. Comparison of Figs. l(b) and l(c) shows that, although under the optical microscope the two microstructures are quite similar, the martensite plates of the specimen shocked at 100 kbars etched in a distinctly different manner. This unique etching behavior of martensite in samples shock-loaded above the 80 kbar transition point has also been observed by Leslie el al.' These investigators determined from X-ray and electron microscope studies that fcc martensite, similar in appearance to normal bcc martensite, had been formed under shock loading. A quantitative determination of the amount of austenite present after shock loading was made by X-ray techniques. Both the methods of Lindren' and Miller' were utilized. The results are shown in Table I. The error limits are those experimentally observed from two independent analyses of each sample and represent the precision of the experiment. The absolute error, which should be similar for each sample, is believed to be about 10 pct. It is seen that as the shock stress increases the amount of austenite present also increases. On the basis of the X-ray and microscopic observations, we conclude that shock loading below the 80 kbar ersal will initiate a martensitic reversal: the amount of reversal that occurs increases with in-

Jan 1, 1969

By F. D. Rosi, C. H. Mathews

THE plastic properties of face-centered cubic metals below room temperature present a field of investigation which has not been extensively ex-plored. The work by Schmid and Boas1 has demonstrated the importance of temperature upon such properties as strain hardening and critical resolved shear stress. The work by Yamaguchi2 upon the shear stress as related to the number of slip bands accentuates the necessity for further experiments of a similar nature. The approach to a mechanical equation of state from the standpoint of thermal fluctuations and activation energies by Becker3 and more recently by Kauzmann4 further emphasizes the need for a quantitative and more comprehensive analysis of the dependence of fundamental plastic properties on temperature. The purpose of the present work was to investigate specifically: (1) The gross shape of the stress-strain curves at several temperatures, (2) the change in the critical shear stress as a function of temperature, and (3) the number and appearance of slip bands as a function of strain and temperature. Preparation of Specimens Single-crystal specimens of 99.996+ pct alumi-num, 1/2 in. in diam and 5 to 6 in. in length, were made by the Bridgman method of gradual solidification from the liquid state. The crystallographic orientation of the single crystals was determined from back-reflection, Laue X-ray photograms ac-cording to the method described by Greninger.6 In most specimens the Laue photograms showed double diffraction spots indicative of the lineage structure type of imperfection, discussed in great detail by Buerger.7 The angular spread of these spots was never observed to exceed 2". Most of the crystals were radiographed to insure against microporosity. In preparing the metal surface for optical microscopy, the following sequence of operations gave good results: The as-cast crystals were turned down in a lathe, 0.001 in. per cut, to obtain a 2.5 in. gauge length. The cold-worked layer resulting from this operation was removed chemically by etching with Tucker's reagent. Then the specimen was polished mechanically through 2/0 metallographic emery paper, after which it was etched again to remove the cold-worked layer resulting from the mechanical treatment. A 48-hr anneal at 580°C ±10°C followed so as to insure an essentially stress-free single crystal. After the annealing treatment, the specimen was electrolytically polished in a 2:l solution of methyl alcohol and concentrated nitric acid. With a current density of 10 amp per sq dm (decimeter) the time required to obtain a satisfactory surface varied from 10 to 12 min. The polish-ing was carried out for short periods of 2 min to avoid rapid deterioration of the solution as well as to enable the rotation of the specimen 180" for uniformity of polish. It was necessary to place the solution in a bath of dry ice in view of its explosive nature at room temperature. Etching of the electrolytically polished surface was accomplished by using the fuming etch-pit method recommended by Lacombe and Beaujard8 for high-purity aluminum. Method for Tensile Testing A modification of the loading equipment devised by Miller9 was used. In this apparatus, the specimen was suspended from a chain and gimbal arrangement (for axial loading) in a heavy steel framework connected at the bottom to a balanced 6:1 lever and bucket system. Loading of the specimen was accomplished by allowing sand to flow from a reservoir into the bucket suspended from the longer end of the lever-arm at a rate of approximately 3 lb per min. Strain measurements were made using the Baldwin SR-4, bonded, resistance-wire, strain gauge and an SR-4 portable strain indicator (type K), which permits a reading accuracy of 2 microinches per inch. For low-temperature study, the gauge was calibrated by measuring the elastic modulus of an annealed stainless steel rod, which is known to be independent of temperature."

Jan 1, 1951

By J. Washburn, R. Drouard, E. R. Parker

Temperature dependence of the rate of recovery in zinc single crystals after a simple shear deformation at low temperature was investigated. Some tentative suggestions regarding the annealed and strain-hardened states of a crystal are discussed. RECOVERY may be defined as the gradual return of the mechanical and physical properties of strain-hardened metal to those characteristic of the annealed material; an increase in temperature increases the rate of recovery. The annealing process in strain-hardened polycrystalline metals is complicated by the inhomogeneity of strain which always exists in aggregates. Polygonization in bent regions of the crystals and growth of new almost strain-free grains starting at points of severe local distortion1-:' make it almost impossible to isolate and study the recovery process. Homogeneously strained single crystals, however, do not polygonize or re-crystallize and hence they can be used advantageously to study recovery. In such crystals strain hardening is completely removed by recovery alone. Since recovery is a process whereby certain lattice disturbances introduced by plastic flow are gradually reduced, a knowledge of the rate and temperature dependence of this process for various conditions of prestrain might be helpful in formulating a model of the strain-hardened state. For simplicity it seemed desirable to limit the type of prestrain to the simplest obtainable, i.e., simple shear strain. In the experiments to be described, recovery was studied by observing changes in the stress-strain curve of prestrained zinc single crystals held for various times at temperatures above that employed for straining. Single crystals were grown from the melt by a modified Bridgeman technique from Horse Head Special zinc 99.99 pct pure, and from spectrographically pure zinc 99.999 pct pure. They were grown as 1 in. diameter spheres and acid-machined' to the final specimen contour. The test section was a cylinder about 1/8 in. high and 3/4 in. in diameter. The conical sections adjacent to the test section were cemented into the grips so the load could be transmitted to the crystal as uniformly as possible. The specimens were oriented so that in testing the maximum shear stress was applied along one of the slip directions, [2110], in the (0001) plane. Details of the production and testing of such specimens have been presented.' Each test was carried out according to the following schedule: 1—The crystal was strained at — 50°C until it reached a maximum shear stress, ,,,. The strain rate was approximately 5 pct per min in all cases. 2—After straining, the crystal was unloaded before the temperature was changed. Unloading required about 3 min. 3—The temperature of the specimen was then increased from — 50°C to the temperature, T, of recovery. This change in temperature was completed in a time of less than 2 min. The specimen remained at temperature, T, for a time, t, which differed for the various specimens. 4—Thereafter the temperature was again reduced to — 50 °C in approximately 3 min. 5—While at —50°C, the stress-strain curve after recovery was obtained. 6—The specimen was then unloaded and annealed for 1 hr at 375 °C in a helium atmosphere to bring about complete recovery. Cooling to room temperature after anneal required 90 min. 7—The same crystal could be re-used for another test because the plastic properties after annealing closely duplicated those of the original crystal. The specimen was immersed during the test in a bath of methyl alcohol which, through a system of tubes, could be pumped through either of two heat exchangers to regulate the temperature; this was accomplished by circulating the liquid through coils immersed in a bath of acetone and dry ice for cooling or in a bath of warm water for heating. Test temperatures were thus maintained constant within ±1°C. The — 50°C temperature was low enough so that no measurable recovery occurred during unloading and reloading. The stress-strain curve continued after recovery along a path below, but approximately parallel to, the path of a curve obtained in an uninterrupted test. Fig. 1 shows some of the results from a specimen of 99.999 pct Zn. The amount of downward displacement of the curve due to recovery was a

Jan 1, 1954

By Nicholas J. Grant, H. C. Chang

Microscopic observations during creep tests were made on AI-20 pet Zn, 80 pet Ni-20 pet Cr, and 25 and 3S aluminum specimens. All these materials failed in an inter-crystalline manner under certain stress and temperature conditions. Particular atten-tion was given to the initiation and propagation of intercrystalline cracks in coarsegrained AI-20 pct Zn specimens. The geometry of the grains and grain boundaries in these specimens was known before the tests. On the basis of the observations and a knowledge of the interaction between grains and grain boundaries, a mechanism of intercrystalline fracture and propagation of the fracture has been proposed. METAL, and alloy fracture occurs essentially in two ways: transcrystalline and intemrystalline. In the past most of the work done in this field was centered on the determination of stress criteria for fracture. The specimens used for these studies were tested under varying conditions of stress state, temperature, and strain rate. Unfortunately, very little attention was given to the initiation and propagation of the fracture, whereas the nature of fracture was examined closely only after failure. Several extensive reviews of these studies have been published by Orowan, Smith, Barrett, and Petch.1, 4 It is well known that a material which exhibits a ductile and transcrystalline fracture can be made to exhibit a brittle and intercrystalline fracture by modifying its composition and by heat treatment. This modification may or may not result in microscopically observable precipitation in the grain boundaries." In the creep of any one alloy the transition of transcrystalline to intercrystalline fracture is a function of stress, strain rate, and temperature." The tendency for intercrystalline fracture to occur increases as the strain rate decreases and the testing temperature increases. Extensive work on high purity aluminum (99.995 pet) under creep conditions showed the importance of the interaction between grains and grain boundaries, and the different responses of grain and grain boundaries to the variables: stress, strain rate, and temperature.7, 8 It was also shown that grain boundary deformation necessarily has to be accommodated in the grains by various deformation means as. for example, fold formation. The type of fracture resulting from the creep of high purity aluminum was invariably found to be transcrystalline. On the other hand, 2S and 3s aluminum were, under certain conditions, found to fracture in an intercrystalline manner." One reason given for this was that the grains could accommodate to a lesser extent the deformation of the grain boundaries.19 It was decided to examine this line of reasoning in greater detail and to investigate the particular interactions between grains and grain boundaries that result in the incidence and progression of inter-ct,ystalline fracture. It is also the purpose of this paper to show where and how intercrystalline cracks start and how they propagate to result in fracture. Several alloys—Al-20 pct Zn, 80 pet Ni-20 pet Cr, 2S and 3s aluminum-— were used for this study, but attention was paid mainly to the behavior of an A1-20 pet Zn alloy, since its general creep behavior has been established." From the results of this study a mechanism of intercrystalline fracture is proposed. Experimental Procedure The experimental procedure was similar to that used in previous work and has been detailed elsewhere.' Two parallel flat surfaces were milled from an originally round specimen, giving a gage portion which was 1x0.09X0.17 in. Some round specimens, 1/4 in. round by 1 in., were also tested. The A1-20 pet Zn specimens. which were annealed at 1030°F for 24 hr, showed two to four grains across the width of the test bar, and most of the grains occupied the whole thickness of the specimenu. Before some of the specimens were subjected to creep, the grain arrangement was mapped out in a development drawing, Fig. 1. The initiation and

Jan 1, 1957

By L. S. Birks

The bainite transformation in a 3.5 pct Ni-1.25 pct Cr steel was studied under various conditions of cooling and stress. Several characteristics may be specified: 1) transformation in the bainite region (925° to 575°F) is very little affected by the manner of cooling from the austenitizing temperature at 1600°F to 575°F)tothe upper limit of bainite transformation at 925°F; 2) starting time for the bainite transformation is the same order of magnitude for either isothermal transformation or continuous cooling, but the rate of transformation is somewhat greater for isothermal transformation; 3) tensile stress accelerates both isothermal and continuous cooling transformation, and 32,000 psi stress changes the form of the isothermal transformation diagram to correspond in appearance to the continuous cooling diagram; 4) transformation for nonlinear, continuous cooling may not be determined directly from the linear, continuous cooling transformation diagram, but may be predicted by assuming first that the fractional amount of austenite transformed in a given small temperature interval depends on the approximate linear cooling rate during that temperature interval and then by summing stepwise over the whole temperature range. IN a previous publication' an X-ray spectrometer was described with which the X-ray diffraction from a specimen could be observed continuously under controlled temperature and tensile stress. This instrument has now been applied to a study of the austenite-bainite transformation in a Ni-Cr steel for both isothermal and continuous cooling conditions, with and without stress. Certain characteristics of the transformation lead to a method of predicting the amount of transformation to be expected at a given temperature for any type of cooling curve. Material and Specimen Preparation The steel chosen for the investigation was a Ni-Cr steel having the composition in the following percentages: 0.30 C, 0.27 Mn, 0.019 P and S, 3.50 Ni, and 1.25 Cr. In order to fabricate specimens suitable for the X-ray spectrometer, a 1/4 in. plate was ground down to 0.060 in. and then cold rolled to about 0.035 in. Next it was heat treated by quenching in oil from 1650°F and tempering at 1200°F for 1 hr. Then it was etched in dilute nitric acid to reduce its thickness to 0.014 in. and cut into blanks in the shape of flat tensile specimens 3 1/4 Vi in. long, 7/16 in. wide, with a notch % in. long and 7/32 in. wide; see Fig. 1. X-Ray Technique Since the X-ray spectrometer has been described in detail elsewhere,' only a brief outline of the principles will be repeated here. A focusing, pow- der-diffraction arrangement' was used, as shown schematically in Fig. 1, and the specimen was mounted vertically in a vacuum furnace (not shown in the figure). The X-rays, moving in a horizontal plane, enter and leave the furnace through beryllium windows. As shown in the figure, X-rays diverging from the line source A are diffracted by the specimen B and converge at the detector slit C. The detector D and the slit C may be set at the proper angle in the horizontal plane to receive X-rays diffracted by either the face-centered phase (austenite) or the body-centered form (ferrite, bainite, martensite). The specimen is heated by electrical conduction between connectors E, and E,, and a Pt—Pt-10 pct Rh thermocouple spot-welded to the center of the notched region on the side away from the X-ray beam indicates the temperature continuously on a Brown recorder. Temperature control is exercised manually with a variable transformer on the input to E,-E,. Any desired time-temperature relationship is easily obtained by first drawing the desired curve on the temperature recorder chart and then adjusting the variable transformer during the run so that the thermocouple

Jan 1, 1957