Search Documents

By C. O. Babcock

In this Bureau of Mines report, the authors present the results of laboratory tests on the burst proneness of coal. Many researchers have studied the violent breaking of large coal masses in underground mines, called bursts, but the causes remain uncertain. They have often assigned to geology and gas pressure the causative roles. The objective of this work is to show that stress can produce bursts in many coals if constraint is necessary for pillar survival and is suddenly lost. We tested coal samples from 15 mines, in 11 coal seams, in six states in the laboratory, and 13 were made to burst. These bursts were produced in several ways, but segmented steel platens were used in the tests reported. Two parameters analogous to the momentum and kinetic energy were used to rank the burst proneness of the coals tested. Tangential strains over the lower surface of the model coal pillar were measured to reveal a periodic slipping prior to the burst. High-speed motion pictures (350 frames per second) reveal the burst behavior in slow motion. We propose a modified Mohr-Coulomb stress-failure criterion to describe the burst behavior. When the horizontal constraint is suddenly lost with little change in the vertical stress, the Mohr stress circle increases in size dynamically, exceeding the static failure condition. When the inertia of the coal mass is overcome, a burst occurs. We conclude that most coals can be made to burst and that such bursts can be expected in mining at increasing depths.

Jan 1, 1984

By R. J. Charles

PREVIOUS study' of simple impact systems indicated that energy required for fracture and size reduction of brittle materials is greatly dependent on the type of loading that is employed. In this regard it was postulated that fracture and size reduction of a brittle specimen might be accomplished by a high velocity impact at an energy level at which a low velocity impact would leave the specimen relatively undamaged. The finite time required to propagate energy away from the point of loading of an impacted object to other parts of the object and to its supports may permit a concentration of energy at the point of impact if the rate of loading is high. Localizing of energy at the point of impact could quickly initiate fractures that would propagate through the impacted material along with the traveling stress waves. As the cracks form, the initially absorbed strain energy would be released and portions of it travel ahead of the wack tips as stress waves. These secondary stress waves, combined with the initial stress waves derived from the impact, would produce high localized strain conditions in front of the fracture zone. The fracture zone would propagate and the specimen shatter. High rates of loading are brought about by short impact times, in turn obtained by employing high velocity projectiles that are of small mass compared to the impacted object. In the case of a low velocity impact, at an energy level equal to that of a high velocity impact that causes fracture, loading rate would be relatively

Jan 1, 1957

By Thomas M. Tharp

INTRODUCTION Attempts to analyze the stability of slopes, foundations and underground openings in discontinuously jointed rock have generally assumed full joint continuity or ignored the role of stress concentration at the tips of discontinuous joints. The most common approach in rock slopes is to consider a failure plane consisting of coplanar, but discontinuous joints separated by intact rock. The intact rock is assumed to fail in shear as a Mohr- Coulomb material and to contribute a strength component proportional to the fraction of the failure plane that is intact rock (Jennings, 1970). An alternative approach by Stimpson (1978) applies Lajtai's (1969) theory for shear strength of discontinuously jointed rock masses to slopes. Lajtai allows tensile failure in the intact rock of a composite surface. This theory yields lower shear strength than that of Jennings (1970) except in the presence of high normal compression, however it also fails to account for the stress concentration at the tip of a discontinuous joint. For a given slope geometry, stresses increase with slope height, but in both of these models rock mass strength is independent of size. A fracture mechanics analysis shows that particularly for small slopes, rock mass strength decreases with size. A continuous stepped failure surf ace produced by propagation of preexisting joints may develop at lower shear stress than predicted by the Jennings (1970) or Lajtai (1969) models. This fracture mechanics model applied to slopes in competent rock is more realistic in its assumed failure mechanism, and for large slopes more conservative than the Jennings (1970) or Lajtai models (1969).

Jan 1, 1984

By H. Reginald Hardy, Y. P. Chugh, Robert Stefanko

Many materials including rocks, ice, metals and their alloys, wood, etc., emit transient vibrations in the audible and subaudible range when stressed. In rocks, this phenomenon is referred to as "microseismic activity, " "rock noise, " or " seismo-acoustical activity. " In metals this phenomenon is often termed "acoustic emission." Each individual microseismic disturbance is generally referred to as a "microseismim" or an "elastic shock." The terms "microseismic activity" and "microseismim" will be employed exclusively in this chapter. Microseismic activity has been observed in many rocks loaded experimentally in the laboratory.1 The form of a group of typical microseismims is shown in Fig. 1. Quantitatively, the microseismic activity in rock under stress is most commonly described by the number of microseismims observed per unit time. This is commonly known as the "noise rate." The noise rate in general increases with increasing stress level and rises sharply just prior to failure of the material.2 The origin of microseismims is not well understood, but it appears to be related to processes of deformation and failure which are accompanied by a sudden release of strain energy. In a polycrystalline material, microseismims may originate at the micro-level as a result of dislocations or at the macro-level by twinning, grain boundary movement, or initiation and propagation of fractures through and between the grains. It is assumed that the sudden release of stored elastic strain energy accompanying these processes generates a stress wave which travels from the point of origin, within the material, to a boundary where it is observed as a

Jan 1, 1972

By Russell A. Carter

Alaska is a land of immense proportions and resources. Its very name, derived from an Aleut term, means "The Great Land." Yet, in a state slightly larger than Texas, California, and Montana combined, there are presently only two-large scale mines in production, excluding dredge operations. Once referred to by its territorial governor as "a storehouse of minerals," Alaska is, in the opinion of many industry observers, at least 20 years away from a healthy, productive mining industry. The mineral potential of the state is tremendous: coal deposits on the North Slope alone have been hypothetically pegged at 1.5 trillion tons. Copper-zinc deposits on the south flank of the Brooks Range are conservatively estimated to be worth $4 billion to $6 billion. However, the problems facing mineral development are of equal magnitude, and include:

Jan 11, 1976

E. E. Russell Tratman, New York City (communication to the Secretary): Mr. Glenn's paper brings up again the question of the part played by coal-dust in colliery-explosions. In the discussion of Sir Frederick Abel's paper on " Accidents in Mines," read before the Institution of Civil Engineers,? much was said about the dangerous properties of coal-dust, and several instances were given of the successful use of a spray of water, water and compressed air, or exhaust-steam from an engine, to keep the mine SUEciently damp to prevent the formation of dust clouds. Methods of preventing shots from blowing out; of using water cartridges to prevent flame ; and of using lime cartridges, wedges and other means of breaking down the coal were also discussed. Mr. Emerson Bainbridge referred to the explosive termed " roburite " (ammonium nitrate and

Jan 1, 1895

By Paul F. Sikora, John W. Weeton, Philip A. Clarkin

Effects of variations in carbon content and micro-structure on the stress-rupture properties of a liquid-phase-sirztered, Izeut-resistunt alloy were studied. Using the powder rnetallurgy technique, specimens could be produced having stress-rupture profierties equivalent to or better than those of the alloy in wrought form. In addition, sintered specimens were easily hot worked even when carbon contents were as high as I pct. Correlations between stress-rupture properties and micro structure were obtained in some cases. IT is well known that many alloys used in high-temperature service are quite complex both from the standpoint of chemical composition and microstruc-ture. During the development of these alloys their complexity has in some cases led to treatment schedules which, while practical, often do not fully utilize available alloying elements. For example, in some alloys, massive carbides that form during ingot practice may never be dissolved by reasonable solution treatments and therefore are unavailable for subsequent precipitation hardening, Ref. 1. This investigation was undertaken to determine whether the powder metallurgy method of consolidation might provide distinct advantages over the conventional melting method. First, segregation of alloying elements might be eliminated or reduced and thus a more efficient use of these elements obtained. Second, the structures produced in powder specimens might differ considerably from those normally seen in castings, which would perhaps result in better response to subsequent mechanical or thermal treatments. If these results could be achieved, it was felt that both forgeability and stress-rupture properties might be improved. The alloy used in this investigation was S-816 produced by powder metallurgy methods. The influence of carbon content over the range of 0.1 to 1.0 wt pct was studied for the alloy in the as-sintered condition and after three additional treatments involving heat treatment, hot swaging, and combinations thereof. EXPERIMENTAL Standard S-816 has the composition shown in Table I. It is a cobalt-base alloy having a nominal carbon content of 0.4 pct and is classified as a precipitation-hardening alloy. This alloy was chosen because it is representative of a class of heat-resistant alloys and because adequate information was available concerning its response to various treatments and its subsequent properties. For this study, -100 mesh alloy powder having essentially the same composition as shown in Table I but without the 0.4 pct C was used. Desired carbon variations, achieved by wet mixing the alloy powder with graphite, ranged from 0.1 to 1.0 wt pct. Specimens were hydrostatically pressed and then sintered in vacuum by slowly heating until incipient melting was observed. Sintering this way gave a liquid phase in the interstices of the powder particles and achieved reasonably high densities. The average density of as-sintered specimens was about 95 pct of wrought alloy density. In order to obtain various microstructures, some specimens were heat treated (solution treated for 24 hr at 2150°F, water quenched; aged 16 hr at 1400°F, air cooled); others were hot swaged at 2150 o F (50 pct reduction in area), while still others were hot swaged (50 pct reduction in area) and then given the above heat treatment. During hot swaging it was observed that forgeability was quite good even when specimens contained as much as 1.0 pct C. Specimens were evaluated by stress-rupture test-

Jan 1, 1962

By R. M. Brick

A PREVIOUS publication 1§ has described the effect of quenching stresses on the lattice parameter values of high-purity aluminum-copper alloys particularly with reference to the solution and precipitation of CuAl2. A similar study has been made of the aluminum-rich aluminum-mag-nesium alloys. Attention has been directed in the present investigation to the magnitude of the quenching stresses as affected by the specimen size and shape, the number of solute atoms and the quenching rate. The effect of cooling stresses in causing plastic deformation or cracking has been considered in relation to the physical properties of the alloy. On reheating alloys in the two-phase field, the time required for pre-cipitation to occur has been observed in connection with the degree of supersaturation, the rate of diffusion of the solute atoms as a function of the comparative atomic radii, degree of strain, temperature of reheating and grain size. A few qualitative comparisons on the relative effect of these factors have been drawn between the aluminum-copper alloys and the aluminum-magnesium alloys.

Jan 1, 1935

By David E. Fogelson, James J. Olson

Rock mechanics as a guide to a safe underground operation is gaining importance as more is under- stood of rock behavior under stress and of the competency of rock after blasting. The U. S. Bureau of Mines' Twin Cities Mining Research Center and White Pine Copper Co. personnel undertook a joint research program recently to define how the rock adjacent to a newly opened underground working could be left as undisturbed as possible. The goal was to leave a competent structure which would tend to limit rock falls and thus decrease the incidence of fatalities from this greatest of all underground hazards. High-amplitude stress waves and borehole gases create a crushed zone in the rock, the thickness of which is about equal to the borehole radius. Beyond the crushed zone, additional structural damage occurs to the rock from the microstructural level up to visible fractures that may extend several feet. This type of rock damage near the final excavation lines reduces rock strength and increases the possibility of failure of the openings from subsequent vibrations or stresses.

Jan 9, 1969

By H. Hanemann

Discussion of the paper of H. HANEMANN and PAUL D. MERICA, presented at the New York meeting, February, 1916, and printed in Bulletin No. 108, December, 1915, pp. 2371 to 2385. JOHN A. MATHEWS, Syracuse, N. Y.-I should like to ask the authors if there is any evidence of chemical change resulting information of, alpha iron from the gamma crystals found in nickel steel of high nickel content when stressed beyond the elastic limit, similar to the effect produced by drastic cooling. Would the stresses mentioned and the drastic cooling both result in an increase in magnetic induction? I would also like to ask the authors if they have made a test of the hardness. It would be very interesting to see whether the hardness decreased under the conditions of stress, as might be the case if alpha iron were produced. PAUL D. MERICA, Washington, D. C.-While it is impossible to state absolutely, it is my belief that the effect of deformation is approximately the same as, that of -drastic cooling, but we did not make a test, of the hardness.

Jan 5, 1916

By D. D. Porter, C. Fairhurst

Crack propagation in the region of a statically pressurized borehole is investigated to determine a role of the sustained borehole pressure following detonation in a blast. The case of a single-hole bench blast is reduced to a plate model, which is considered both theoretically and experimentally. Based on the principle of least work, it is hypothesized that the path of any crack in the plate will coincide with one of a family of maximum principal stress trajectories. These trajectories were computed, and critical experiments in glass, designed to test the effects of controlled crack origin and of changed trajectories from different loading configurations, confirm this hypothesis. It is concluded that under ideal conditions the crack path can be predicted and that cracks can be produced in the absence of either high-amplitude stresses or stress waves. Energy considerations for crack extension are discussed, and, based on the strain energy distribution, a relationship between hole burdens and spacings is revealed, a critical burden is demonstrated, and a maximum crater width is shown to exist.

Jan 1, 1971

By R. R. Nash, W. F. Sheely

Experiments were conducted on magnesium monocrystals in order to collect quantitative information on the mechanisms which limit the rate of basal slip. Using critical shear stress and creep data, activation energies for creep at low aid at high temperatures were derived. The activation energy at low temperatures is the same as that for jog formation and the activation energy at high temperatures agrees with that for climb. COTTRELL has suggested that at low temperatures, the expansion of dislocation loops under stresses near the yield strength is limited by the rate at____ which the expanding loops can cut the "forest" of dislocations passing through the glide planes.' On the basis of this mechanism, seeger2 has derived expressions for low-temperature creep and for the relation of flow stress of single crystals to temperature. In the work reported here, the authors have performed experiments designed to obtain quantitative data on the physical properties of the dislocation intersection mechanisms operating during basal slip in pure magnesium monocrystals. Above a critical temperature, dislocations thread-

Jan 1, 1961

By M. A. Meyers, P. P. Meyers

The analysis of the phenomena involved in determining the compressive strength of iron-ore agglomerates leads to the identification of important parameters. It is shown mathematically that the pellet rupture strength is proportional to the cross-sectional area. Fracture is initiated at the center of the pellets by the tensile stresses developed by the compressive loads normally to the compressive axis. The variation in strength between individual pellets of identical composition and subjected to identical treatments u due to internal voids of varying sixes that act as stress-concentration sites. Two novel testing procedures are proposed. The first consults of testing the pellets between two plates having three steel spheres each. This configuration simulates much better the environment actually encountered by the pellets. The second procedure consists of a thick-walled cylinder in which a piston penetrates; a large group of pellets is tested simultaneously, as the stress versus strain plot is being recorded. This latter test presents vacant advantages over the conventional testing procedure; the main one is that one single test is sufficient to characterize the mechanical response of the pellets.

Jan 1, 1984

By R. H. Thielemann

THE conventional short-time tensile test provides a reliable means of predicting the sustained load-carrying capacity of steels only when the temperature is such that continuous plastic flow does not occur. At elevated temperatures, stresses considerably less than the short-time rupture value may produce continuous flow, with fracture occurring only after long periods of time. The amount of flow or creep accompany-ing failure varies for different steels, and depends, to a large extent, on the temperature and the duration of the test. Service records of cracking stills, steam superheaters and high-temperature boilers have shown that brittle fractures sometimes occur with little or no warning. In installa-tions of this type, localized stresses are often encountered, and steels must be capable of withstanding a certain amount of deformation without fracture. The sustained-load rupture test determines the expected life and corresponding ductility of steels at various stresses and tempera-tures. It also yields additional information regarding the effect of micro-structure and metallurgical stability on the high-temperature properties.

Jan 1, 1939

By Jean-Jacques Prompsy, J. S. Rinehart

Some time ago a study was initiated at the Colorado School of Mines in an effort to arrive at a better understanding of the stress fields developed within drill bits under dynamic loading and the influence that these stress fields could have on the failure of the bits. Particular emphasis has been given to the influence that bit shape has on the establishment of highly localized, potentially destructive stress inhomogeneities within the bit. The study has been divided into three phases involving three velocity regimes: impacts at very low velocities, 0 to 20 ft/sec, a velocity range in which dynamic effects are just beginning to be found; impacts at velocities ranging from 20 to several hundred ft/sec, a range commonly encountered in practical drilling operations; and impulsive loading through the detonation of explosives, a region in which the dynamic effects are greatly exaggerated and made more identifiable. The ultimate objective is to provide basic data which will enable the mitigation through judicious design of the frequency and severity of these transient concentrations of intense stress, thereby prolonging and increasing drill efficiency. This paper presents results of the third phase of this study — the development of a better understanding of the dynamics and mechanics of failures caused by transient stress-wave interactions. The impulsive loading or transient waves in these experiments were generated by detonating small explosive charges placed on the ends of Plexiglas cylindrical rods terminating in truncated cones. Under such intense loading, dynamic effects are greatly exaggerated and, hence, made more identifiable. The explosion generates a high-intensity transient stress disturbance which moves through the rod, reflects from surfaces which lie in its path, and establishes momentarily narrow regions of high concentrations of stress where failure of fracture may occur. The peregrinations of these waves, their interactions and their effects have already been described in the literature (see, for example, Refs. 1 and 2). The locations and extent of the regions quite apparently are strongly dependent on specimen shape, making it possible through judicious shaping of specimens to relocate the highly stressed regions, minimize their extent, or eliminate them entirely. These experiments were designed, first, to identify more clearly the vulnerable regions in geometries relevant to drill-bit design and, then, to modify these regions in a predictable way by changing specimen shape. Through this latter process, it is anticipated that better bit design might evolve. The specimens used in the experiments were cylindrical rods, 1 1/2 and 1 1/8 in. in diameter, ended by a truncated cone, with the cone angles ranging from 45° to 130°. Upper cone face diameters were 1/2, 3/4, or 1 in. A small plastic-covered electric blasting cap detonated on the axis of the specimen produced the spherical shock wave. The detonators used were Olin Mathieson No. 6, which induced into the rod a transient saw-toothed stress disturbance of about 3-microseconds duration, corresponding to a wave length of 0.3 in. in the Plexiglas. Five distinct systems of fracture were observed: (1) along the axis of the rod, a lower system of fractures, the cracks focusing around one point for specimens having cone angles of 80° and 90° and, as the cone angle was increased, spreading downward; (2) just above these fractures, an upper system of fractures composed of horizontal cracks observable in some specimens but not of any appreciable extent; (3) a third system of axial cracks still above the latter, observable in the small cone-angle specimens; (4) in the upper part of the specimen, a system of radial fractures extending from the blasting point; and (5) circular spalling due to reflection of the wave on the boundary of the cylinder. Only the first three systems, the axial fractures, are examined here. LOWER TENSILE FRACTURE SYSTEM The first, lower system of tensile fractures, shown in the photograph of Fig. 1, was observed in almost all of the specimens. It was due to the reflected tensile wave coming in from the boundary of the cylinder as shown in Fig. 2. The reflected wave was cylindrically convergent and focused

By Tibor Stefansky, John E. Dorn

MOTT and Nabarro1-5 were first to illustrate the importance of the flexibility of dislocations in accounting for the strengthening that metals undergo due to the presence of internal-strain centers. Such strain-centers might arise from a number of causes such as radiation damage, the presence of semicoherent and coherent precipitates and clusters, as well as individually dispersed interstitial and misfit substitutional solute atoms. Each strain-center induces positive and negative shear stress fields on the slip planes of the surrounding alloy matrix. In order to effect plastic deformation, therefore, the alloy must be subjected to sufficiently high applied shear stresses to push dislocations past all such internal stress fields. If dislocations were inflexible and moved as rigid lines, they would be equally pushed and pulled by internal stress fields. At this extreme the strengthening would be vanishingly small. Dislocations, however, are not rigid; they are flexible and extensible. They wiggle between positive and negative strain-centers, thus increasing their line energy at the expense of their interaction energy with strain-centers. cottrel16 and Friedel7,8 have independently presented lucid reviews of the significance of the Mott-Nabarro dislocation-flexibility concept to the strain-center strengthening of alloys. Their analyses however were only semi-quantitative. There is evidence in the recent literature of renewed interest in a more rigorous analysis of flexibility. Thus, Gleiter9 and Gerald" have shown that the calculated strain-energy interaction between a dislocation and the stress fields of coherent precipitates can be seriously in error if the flexibility of the dislocation is not taken into account. This report will be concerned with a more detailed analysis of the problem based on the following approximations: 1) Although many types of strain-centers exist, the following analysis will be limited to the case of solute-atom strain-centers in fcc substitutional alloys. 2) To facilitate the analysis by avoiding statistical considerations, the strain-Centers are assumed to be in regular arrays on the slip plane. Although the quantitative results are somewhat dependent on the type of array that is assumed, the qualitative trends are similar for various arrays that were studied. 3) An adjustment of the results from those for square arrays to those for the more realistic case of a random distribution of strain-centers is accomplished by adopting the interesting statistical theory first introduced by Kochs,11,12 elaborated on by Dorn, Guyot, and stefansky,13 and analyzed by Foreman and Makin14 in their computerized experiments. 4) For simplicity the dislocation lines are taken to wiggle about their edge orientation and no correction is applied to their line energy for deviations from edge configurations or for the elastic interaction between segments of the now curved dislocation. It will be shown that for extremely low concentrations of atomic strain-centers the strengthening increases with the square root of their concentration. For slightly higher concentrations the strengthening rate becomes less rapid. At a critical concentration a maximum strength is obtained and a decrease in the strengthening takes place as the concentration of solute atoms is further increased. These trends are a direct consequence of dislocation flexibility. They arise from changes in the amplitude of the waviness of the dislocation line at the yield stress with solute atom concentration. Despite the simplifying assumptions that were made, the results agree qualitatively with appropriate experimental data. I) STRESS FIELDS ON SLIP PLANES Internal stresses are introduced in a lattice whenever a host atom of radius ro is replaced by another that has a different atomic radius. According to the classical theory of linear elasticity,15 the stress field about a solute atom at the origin of a spherical coordinate system is given by arr=-4G€(?_0)3 ffflfl ="W =2G€{t) f°rr^ro(l+e) UJ where G is the shear modulus of elasticity and Y, = ro(l + E) is the radius in situ, of the substituted atom. As shown by ~shelb~,'~ this approximation assumes that the bulk modulus of elasticity of the substituted atom is identical with that of the host species. ~abarro'~ suggested that the strain E can be deduced

Jan 1, 1970

By Leslie W. Austen

ROTARY kiln operators will agree that some of the most severe conditions a refractory must stand occur in the hot zone of a kiln burning Portland cement, dead burn dolomite, magnesite, peri-clase, and similar materials. Frequently the operator is faced with factors beyond his control which drastically shorten the life of refractories. Shutdown due to mechanical failure can be serious if the period is of sufficiently long duration to cause the dropping of coating or the loosening of the lining. A change in slurry can affect the coating and cause ring buildup. A change in type of fuel and its effect upon the flame can cause a shift in location of the hottest zone. Weekend shutdowns or any other interruption can cause the operator trouble and may damage the refractories, since stopping and starting a rotary kiln is certainly more difficult than stopping and starting a motor. Some operators have tried to set an estimate of damage for each shutdown in equivalent days of running time. Conditions affecting the refractory may be roughly grouped in four classes: chemical attack, mechanical stress, thermal shock, and abrasion. Chemical Attack: The drive to obtain maximum production through a kiln demands maximum operating temperatures, temperatures which are limited more by the ringing up or melting of the clinker. This can cause interface temperatures at the junction of coating and refractory which require the use of a basic kiln block to withstand the chemical attack. Chemical changes take place within the refractory itself, especially in chemically bonded or unburned kiln blocks. These changes cause the formation of the ceramic or burned bond. Migrating liquids or fluxes from the kiln charge have an effect within the refractory and lead to mineral or glass formation. The alkalies, sodium and potassium, migrate into the refractory as silicates, chlorides, sulphates or other salts. They may move under capillary action or may be caused to move by volatilization with condensation in the cooler portion. Mechanical Stress: Concentrated stress may be caused by several factors or combinations thereof. I—The rings of refractories must be kept tight and rigid within the kiln, and this alone demands considerable force to hold the blocks in place. So that the force will not be concentrated, the blocks should fit the circle as perfectly as possible, with the faces in contact overall. 2—As the kiln is heated, thermal expansion takes place at the hot end of the kiln block. Since this disturbs the plane face it too can cause a concentrated stress at the two ends of the block, and shearing stress can be set up within the brick itself because of the difference in expansion between the two ends. 3—If a lining becomes loose and moves in the shell very severe stress can be set up, and as the kiln rotates this load changes and gives the effect of repeated loading. Permanent expansion of the refractory can also cause severe loading. 4—Not least important, flexing of the kiln is frequently the cause of concentrated stresses. Thermal Shock: Thermal shock, the result of heating and cooling too rapidly, occurs on starting and stopping or when a large patch of coating drops, exposing the bricks. Again, its destructive effect is often the result of phase change, liquid to solid or the reverse; dense refractories loaded with glass-forming impurities are particularly susceptible. Thermal shock is a. problem with refractories set in the wall or roof of a stationary furnace, and becomes even more serious in a rotary kiln, the tendency to spa11 being magnified with movement and concentration of stress. Uniform rate of feed and loading insures both better coating and a more uniform stress. Abrasion: If the refractories do not take a coating, abrasion can become a most destructive factor. Movement of the lining in shell or movement of loose blocks causes abrasion, which is also most destructive if the refractories do not take a coating. An analysis of the problem of basic lining for the hot zone reveals, therefore, a number of desirable characteristics: high refractoriness, basic chemical reaction, resistance to spalling, good strength at all stages, ability to take coating, true sizing, volume stability, and abrasion resistance. Increased demand

Jan 1, 1953

By T&apos Ke, ing-sui

NUMEROUS investigators have observed that internal friction accompanies cold-working of metals and the effect of annealing is to reduce this internal friction.1,2 However, - most of the experiments were made at high stress amplitudes and the principal purpose was to study the increase of internal friction as a result of the applied cyclic stress during measurement. In order to study the internal friction introduced by cold-working applied prior to the measurement, the stress level applied during the measurement of internal friction must be sufficiently small. The results of measurement are significant and can be used for a base of comparison only when the applied cyclic stress is so small that the internal friction is independent of stress amplitude. Internal friction of cold-worked metals under small stress level has been studied by a number of workers8 -" he internal friction was measured around room temperature with a frequency of vibration of the order of kilocycles per second. The purpose of this paper is to report a study of the change of internal friction when severely cold-worked aluminum was annealed at successively higher temperatures until it was completely recrys-tallized. The measurements of internal friction were made over a range of temperature extending from room temperature up to the temperature of prior anneal. The frequency of vibrations used was about one cycle per second. The apparatus used for the internal friction measurements to be reported in this paper was a torsion pendulum with the specimen in wire form as the suspension fiber. The description of this apparatus and the method of measurement have been previously given.7,8 The applied stress was sufficiently small SO that the magnitude of internal friction is independent of stress level at each temperature range concerned. Corresponding to this stress the maximum shearing strain on the surface of the specimen is of the order of l0-5 and lower. The in- ternal friction (Q-1) is reported as 1/p times the logarithmic decrement. Internal Friction Versus Temperature of Anneal: Fig. 1 shows the internal friction measurements performed upon 99.991 pct aluminum subjected to 95 pct reduction in area. The final diameter of the wire is 0.033 in. This figure gives a general survey of the effect of temperature of anneal and of temperature of measurement. The internal friction of the cold-worked specimen was first measured at room temperature. It was then annealed at 50°C for one hour and the internal friction measured at 50°C and at room temperature. The same wire was successively annealed at higher temperatures for one hour and measurements were taken at the annealing temperatures and lower temperatures as before. Such a procedure was followed in order to stabilize the internal friction at the temperature of measurement so that during the measurement which generally takes about half a minute, there is no detectable change in internal friction. This series of measurements .was made up to 450°C. After each annealing a short test piece of the specimen, which had received the same past thermal and mechanical treatments, was taken out for metallographic examination. It is seen from fig. 1 that up to the annealing temperature of 250°C we have the following observations: for any given temperature of measurement, the internal friction is lower the higher the temperature of prior anneal. When the annealing temperature is 290°C or higher, the internal friction at the annealing temperature drops abruptly to a value which is much smaller than that for the previous curve. Metallographic examinations showed that the recrystallization of the specimen was completed after the annealing at 290°C. Fig. 1 shows that, as far as internal friction is concerned, there is no abrupt transition between the processes of recovery and recrystallization. Averbach has also reached the conclusion that recovery may be a process analogous to recrystallization on the basis of X ray extinction measurements in brass." The effect of annealing temperature upon the internal friction at room temperature is shown by curve I of fig. 2. In this figure the internal friction at room temperature was plotted as a function of annealing temperature. It is seen that the internal friction decreases rapidly at first with an increase

Jan 1, 1951

By Leslie W. Austen

ROTARY kiln operators will agree that some of the most severe conditions a refractory must stand occur in the hot zone of a kiln burning Portland cement, dead burn dolomite, magnesite, peri-clase, and similar materials. Frequently the operator is faced with factors beyond his control which drastically shorten the life of refractories. Shutdown due to mechanical failure can be serious if the period is of sufficiently long duration to cause the dropping of coating or the loosening of the lining. A change in slurry can affect the coating and cause ring buildup. A change in type of fuel and its effect upon the flame can cause a shift in location of the hottest zone. Weekend shutdowns or any other interruption can cause the operator trouble and may damage the refractories, since stopping and starting a rotary kiln is certainly more difficult than stopping and starting a motor. Some operators have tried to set an estimate of damage for each shutdown in equivalent days of running time. Conditions affecting the refractory may be roughly grouped in four classes: chemical attack, mechanical stress, thermal shock, and abrasion. Chemical Attack: The drive to obtain maximum production through a kiln demands maximum operating temperatures, temperatures which are limited more by the ringing up or melting of the clinker. This can cause interface temperatures at the junction of coating and refractory which require the use of a basic kiln block to withstand the chemical attack. Chemical changes take place within the refractory itself, especially in chemically bonded or unburned kiln blocks. These changes cause the formation of the ceramic or burned bond. Migrating liquids or fluxes from the kiln charge have an effect within the refractory and lead to mineral or glass formation. The alkalies, sodium and potassium, migrate into the refractory as silicates, chlorides, sulphates or other salts. They may move under capillary action or may be caused to move by volatilization with condensation in the cooler portion. Mechanical Stress: Concentrated stress may be caused by several factors or combinations thereof. I—The rings of refractories must be kept tight and rigid within the kiln, and this alone demands considerable force to hold the blocks in place. So that the force will not be concentrated, the blocks should fit the circle as perfectly as possible, with the faces in contact overall. 2—As the kiln is heated, thermal expansion takes place at the hot end of the kiln block. Since this disturbs the plane face it too can cause a concentrated stress at the two ends of the block, and shearing stress can be set up within the brick itself because of the difference in expansion between the two ends. 3—If a lining becomes loose and moves in the shell very severe stress can be set up, and as the kiln rotates this load changes and gives the effect of repeated loading. Permanent expansion of the refractory can also cause severe loading. 4—Not least important, flexing of the kiln is frequently the cause of concentrated stresses. Thermal Shock: Thermal shock, the result of heating and cooling too rapidly, occurs on starting and stopping or when a large patch of coating drops, exposing the bricks. Again, its destructive effect is often the result of phase change, liquid to solid or the reverse; dense refractories loaded with glass-forming impurities are particularly susceptible. Thermal shock is a. problem with refractories set in the wall or roof of a stationary furnace, and becomes even more serious in a rotary kiln, the tendency to spa11 being magnified with movement and concentration of stress. Uniform rate of feed and loading insures both better coating and a more uniform stress. Abrasion: If the refractories do not take a coating, abrasion can become a most destructive factor. Movement of the lining in shell or movement of loose blocks causes abrasion, which is also most destructive if the refractories do not take a coating. An analysis of the problem of basic lining for the hot zone reveals, therefore, a number of desirable characteristics: high refractoriness, basic chemical reaction, resistance to spalling, good strength at all stages, ability to take coating, true sizing, volume stability, and abrasion resistance. Increased demand

Jan 1, 1953

By Leslie W. Austin

ROTARY kiln operators will agree that some of the most severe conditions a refractory must stand occur in the hot zone of a kiln burning Portland cement, dead burn dolomite, magnesite, periclase, and similar materials. Frequently the operator is faced with factors beyond his control which drastically shorten the life of refractories. Shutdown due to mechanical failure can be serious if the period is of sufficiently long duration to cause the dropping of coating or the loosening of the lining. A change in slurry can affect the coating and cause ring buildup. A change in type of fuel and its effect upon the flame can cause a shift in location of the hottest zone. Weekend shutdowns or any other interruption can cause the operator trouble and may damage the refractories, since stopping and starting a rotary kiln is certainly more difficult than stopping and starting a motor. Some operators have tried to set an estimate of damage for each shutdown in equivalent days of running time. Conditions affecting the refractory may be roughly grouped in four classes: chemical attack, mechanical stress, thermal shock, and abrasion. Chemical Attack: The drive to obtain maximum production through a kiln demands maximum operating temperatures, temperatures which are limited more by the ringing up or melting of the clinker. This can cause interface temperatures at the junction of coating and refractory which require the use of a basic kiln block to withstand the chemical attack. Chemical changes take place within the refractory itself, especially in chemically bonded or unburned kiln blocks: These changes cause the formation of the ceramic or burned bond. Migrating liquids or fluxes from the kiln charge have an effect within the refractory and lead to mineral or glass formation. The alkalies, sodium and potassium, migrate into the refractory as silicates, chlorides, sulphates or other salts. They may move under capillary action or may be caused to move by volatilization with condensation in the cooler portion. Mechanical Stress: Concentrated stress may be caused by several factors or combinations thereof. 1-The rings of refractories must be kept tight and rigid within the kiln, and this alone demands considerable force to hold the blocks in place. So that the force will not be concentrated, the blocks should fit the circle as perfectly as possible, with the faces in contact overall. 2-As the kiln is heated, thermal expansion takes place at the hot end of the kiln block. Since this disturbs the plane face it too can cause a concentrated stress at the two ends of the block, and shearing stress can be set up within the brick itself because of the difference in expansion between the two ends. 3-If a lining becomes loose and moves in the shell very severe stress can be set up, and as the kiln rotates this load changes and gives the effect of repeated loading. Permanent expansion of the refractory can also cause severe loading. 4-Not least important, flexing of the kiln is frequently the cause of concentrated stresses. Thermal Shock: Thermal shock, the result of heating and cooling too rapidly, occurs on starting and stopping or when a large patch of coating drops, exposing the bricks. Again, its destructive effect is often the result of phase change, liquid to solid or the reverse; dense refractories loaded with glass-forming impurities are particularly susceptible. Thermal shock is a problem with refractories set in the wall or roof of a stationary furnace, and becomes even more serious in a rotary kiln, the tendency to spall being magnified with movement and concentration of stress. Uniform rate of feed and loading insures both better coating and a more uniform stress. Abrasion: If the refractories do not take a coating, abrasion can become a most destructive factor. Movement of the lining in shell or movement of loose blocks causes abrasion, which is also most destructive if the refractories do not take a coating. An analysis of the problem of basic lining for the hot zone reveals, therefore, a number of desirable characteristics: high refractoriness, basic chemical reaction, resistance to spalling, good strength at all stages, ability to take coating, true sizing, volume stability, and abrasion resistance. Increased demand

Jan 1, 1952