Search Documents

By Alfred H. Bell, George V. Cohee

Illinois produced 146,788,000 bbl. of oil in 1940, or nearly 11.0 per cent of the total for the United States, and ranked fourth among the oil-producing states. Its production was only slightly less than that of Oklahoma, which produced 11.5 per cent of the national total. Illinois' production in 1940 represents an increase of 55 per cent over the previous year, when it amounted to 94,912,000 barrels. The development of the Devonian limestone in the Salem and Centralia fields is largely responsible for the increase in production during 1940 Production from the Devonian limestone in these two fields was estimated to be 36,698,000 bbl., or 25 per cent of the state's total production (Table I). The increase in production during June, when the state's daily average production attained a peak of 518,200 bbl. for the week ending June 29, was due to the Devonian production at Centralia (Fig. I). The initial production of the best Devonian wells in the Centralia field was as high as 12,000 bbl. in 24 hr. Daily average production in IIIinois for 1940 was 400,000 bbl. of oil, but actually daily production fluctuated widely during the year. At the beginning of 1940 daily production was approximately 330,000 bbl. During the first hali of the year it in-creased irregularly to the peak in June mentioned above and as the prolific Devonian producing areas were drilled up, the state's daily production declined rapidly during July and continued to decline, although more slowly, until the end of the year, when the daily production was approximately 325,000 bbl. The daily average production per well in the new fields at the end of the year was approximately 40 bbl. (Fig. I). Oil from the Devonian was also produced in the Bartelso field, Clinton County, the Sandoval field, Marion County, and the Irvington field, Washington County, bringing the estimated total production from the Devonian limestone to about 26 per cent of the state's total production, The remainder was obtained largely from the Mississippian system. About 2 per cent of the total was from Pennsylvanian and Ordovician strata. The decline in the Devonian limestone production has been so rapid that the 1941 output from this system will probably be only a small fraction of that of 1940 unless large new reserves are discovered. The "Trenton" (Ordovician) limestone has been tested in two wells in the Centralia field and both were small oil producers at a depth of about 4000 it. The "Trenton" also was found productive in the Salem field at a depth of 4500 ft. (Table 5). The initial production of the discovery well, which was completed shortly after the end of the year, was 130 bbl. on pump. Other wells drilled early in 1941 had initial productions averaging 172 barrels. The outlook for 1941 is for a continuation of drilling activity in Illinois, but at a declining rate (Fig. I, upper curve). The most active area at the end of 1940 was in the deep basin area in Wabash, Edwards, White, and Hamilton Counties.

Jan 1, 1941

By Alfred H. Bell, George V. Cohee

Illinois produced 146,788,000 bbl. of oil in 1940, or nearly 11.0 per cent of the total for the United States, and ranked fourth among the oil-producing states. Its production was only slightly less than that of Oklahoma, which produced 11.5 per cent of the national total. Illinois' production in 1940 represents an increase of 55 per cent over the previous year, when it amounted to 94,912,000 barrels. The development of the Devonian limestone in the Salem and Centralia fields is largely responsible for the increase in production during 1940 Production from the Devonian limestone in these two fields was estimated to be 36,698,000 bbl., or 25 per cent of the state's total production (Table I). The increase in production during June, when the state's daily average production attained a peak of 518,200 bbl. for the week ending June 29, was due to the Devonian production at Centralia (Fig. I). The initial production of the best Devonian wells in the Centralia field was as high as 12,000 bbl. in 24 hr. Daily average production in IIIinois for 1940 was 400,000 bbl. of oil, but actually daily production fluctuated widely during the year. At the beginning of 1940 daily production was approximately 330,000 bbl. During the first hali of the year it in-creased irregularly to the peak in June mentioned above and as the prolific Devonian producing areas were drilled up, the state's daily production declined rapidly during July and continued to decline, although more slowly, until the end of the year, when the daily production was approximately 325,000 bbl. The daily average production per well in the new fields at the end of the year was approximately 40 bbl. (Fig. I). Oil from the Devonian was also produced in the Bartelso field, Clinton County, the Sandoval field, Marion County, and the Irvington field, Washington County, bringing the estimated total production from the Devonian limestone to about 26 per cent of the state's total production, The remainder was obtained largely from the Mississippian system. About 2 per cent of the total was from Pennsylvanian and Ordovician strata. The decline in the Devonian limestone production has been so rapid that the 1941 output from this system will probably be only a small fraction of that of 1940 unless large new reserves are discovered. The "Trenton" (Ordovician) limestone has been tested in two wells in the Centralia field and both were small oil producers at a depth of about 4000 it. The "Trenton" also was found productive in the Salem field at a depth of 4500 ft. (Table 5). The initial production of the discovery well, which was completed shortly after the end of the year, was 130 bbl. on pump. Other wells drilled early in 1941 had initial productions averaging 172 barrels. The outlook for 1941 is for a continuation of drilling activity in Illinois, but at a declining rate (Fig. I, upper curve). The most active area at the end of 1940 was in the deep basin area in Wabash, Edwards, White, and Hamilton Counties.

Jan 1, 1941

By Robert S. Dewey

More wells were drilled in West Texas† during 1944 than in any year since 1941. As compared with 1943, there was an 82.5 per cent increase in the total number of completed wells. The 1646 wells required an estimated 140,715 days to complete for a total of 7,632,249 ft. An average of 85 completion days was required to drill to an average of 4630 ft. This depth is approximately 100 ft. greater than that of the previous year. It is estimated that $100,000,000 was invested in drilled wells. As of Dec. 31, 1944, there were 270 field and 91 wildcat wells being drilled. While an identical number of wells were drilling Dec. 31, 1943, the proportion of wildcats increased in 1944 from 19.7 to 25.2 per cent. During 1944, oil wells were completed in 103 of the 164 fields in West Texas. Of the 1361 oil wells, 385 were in Slaughter, 116 in Fullerton, 63 in North Cowden, 62 in Fuhrman-Mascho, 59 in Wasson, 52 in Westbrook and 47 in North Ward. Approximately 22 per cent of the wildcat drilling was to pre-Permian formations. Despite the increasing proportion of wildcat wells drilled, the wildcat discovery rate has declined since the year 1942. AS compared with 1943, the number of wildcat wells drilled increased from 11.7 to 12.7 per cent and the footage in wildcat exploration increased from 13.3 to 13.8 per cent of the total. The monthly production of crude continued to increase to a peak of 15,336,000 bbl. in October 1944. As compared with a similar peak production in October 1943, there was a 37.3 per cent increase. The yearly production increased from 98,165,-ooo bbl. in 1943 to 159,943,000 bbl. in 1944, an increase of 62.8 per cent. Based upon an assumed average price of $1.00 per barrel and less 1/8 royalty, the gross return to the producer amounts to $140, 000,000. From 1943 to 1944, the average number of producing wells increased 6 per cent while the average daily production per well increased 53.1 per cent. The average daily production per well increased from 17.5 bbl. in 1943 to 26.8 bbl. in 1944. The proportion of flowing wells decreased from 50.5 per cent in January to 49.1 per cent in December 1944. Drilling With the continued shortage of labor and materials, drilling costs have risen sharply. Just how much is difficult to ascertain. Owing to competition for available drilling rigs, contractors are reluctant to assume drilling risks. In consequence, some contracts are let on a cost plus basis, or day work below some specified depth with the operator furnishing part of the consumable materials, such as mud and drilling bits. Contractors are having difficulty in maintaining full and effective drilling crews with insufficient and inexperienced labor. Service companies have inadequate labor and equipment to meet their appointments promptly. Pipe Lines The Gulf Pipe Line Co. increased the capacity of its 10-in. main line by filling in gaps amounting to 75 miles on the loops between Judkins and Weatherford, Texas.

Jan 1, 1945

By C. C. Herrick

The vapor pressure of indium has been measured by the torque-effusion technique, as a function of temperature between 1102o and 1422oK. For liquid indium, the vapor pressure (in atmospheres) can be represented by the equation -R In P = 5.782 x104/T - 25.29from 1000o to 1422oK. Extrapolation yields a calculated normal boiling point of 2329°K and a heat of vaporization at 298 oK of 58.09 kcal per mole by the third-law method and of 58.39 kcal per mole by the second-law method. Calculations indicate that the free-energy functions of Hultgren are to be preferred to those of Guruich. BECAUSE of the potential uses of liquid metals, it is important that convenient experimental methods be developed which will lead to a sufficient body of thermodynamic data so that reasonable estimates of properties of liquid metals can be made. Indium is particularly well-suited to investigation, since it remains liquid over a long temperature interval, it alloys readily, suitable containers for it are easily procured, and relatively few investigations of its thermodynamic properties in the region above 1000°K have been made. PREVIOUS RESEARCH The first determination of the vapor pressure of indium was made by Anderson,' using the Knudsen method and silica-lines stainless-steel cells. Kohlmeyer and spandau2 determined the normal boiling point, and a mass-spectroscopic investigation has been made by Lyubimov and Lyubitov.3 (Unfortunately, only an equation representing the data of the latter investigators has been available to us.) Hultgren et al.4 and Gurvich5 have published discordant tables of the free-energy functions for indium. EXPERIMENTAL METHOD The torsion-effusion principle has been described amply in the literature.8,7 With this method, one observes the angular deflection induced by effusion of vapor from a multihole effusion cell which is suspended from a filament producing a small rotational restoring force. The pressure within the effusion cell can be computed from the relation ziaifiai where k is the torsion constant of the filament, 6 is the observed angular deflection, and ai, fi, and qi are the area, force factor, and moment arm of the ith effusion orifice. The force factor f is analogous to the Clausing factor,' and corrects for the reduction in effusive force attributable to the finite geometry of the effusion orifice. Schultz and Searcy' have tabulated the force factors for various tube geometries. EXPERIMENTAL APPARATUS The physical arrangement employed in this study is shown in Fig. 1. The furnace elements are six Globar heat rods with 15-in. hot zones. Temperature is maintained to * 1°K by a Beck mechanism driving two 26-amp Powerstats in parallel. A Pt (Pt, Rh 10 pct) thermocouple serves as the sensing element. Four inner tubes act as vibration isolators; the air pressure required for maximum isolation was determined empirically, and is maintained by a solenoid valve. The tungsten fiber, 9 by 0.002 in., is joined to an 0.008-in. tungsten wire or graphite rod via a machined lightweight chuck.

Jan 1, 1964

By R. G. Hudson, H. W. Paxton

The activities of iron and chromium in their binary system have been measured by the Knudsen orifice technique. The system is close to ideal at 1200- 1250 C with slight positive deviations. The effect of this on the liquidus and solidus is discussed and these are calculated for two limiting assumptions. The vapor pressure of pure iron, pure chromium, and one alloy is compared with that obtained by the Langmuir free-evaporation technique. The results agree, indicating a vaporization coefficient close to 1. HERE are no reported data on the thermody-A namic activity of iron and chromium in the solid portions of the phase diagram. It is generally assumed'.' that the liquid solutions of iron and chromium obey Raoult's law. Chen and Chipman" have inferred that the liquid solution obeys Raoult's law. The minimum' in the solidus-liquidus curves for the iron-chromium system shows that there are deviations from ideality in either the solid or liquid or both. Because of the importance of developing reliable techniques for obtaining activity data in alloy systems at high temperatures and of the data so obtained, an investigation of the activity of iron and chromium in the binary at 1200-1250 C was undertaken using the Knudsen cell. Experimental The apparatus and experimental procedures used in this investigation were described in a previous paper." The various materials used for the construction of the Knudsen cell are listed in Table I. The metal used for the determination of the vapor pressure of chromium was 99.9 pet pure, obtained from A. D. Mackay, Inc. The iron was obtained as electrolytic grade from Fisher Scientific Company. The Fe-Cr alloys used are shown in Table 11. The largest error and controlling factor in the accuracy in the experiments reported here are introduced because of temperature uncertainty, which is estimated to be ±3 deg C. This introduces an uncertainty of 26 pet in the measured pressure. Experimental Results and Calculations The vapor pressures of pure iron and pure chromium were calculated from the measurements by the Knudsen equation3 on the assumption that only Cr or Fe atoms were present in the gas phase. For metal vapors, at the high temperatures and low pressures involved in these measurements this should be a reasonable assumption. Whitman" corrections for the cells were made. The data and results of pressure calculations are presented in Table I, and are plotted in Fig. 1. In addition the heat of vaporization at the absolute zero, ?E°°, has been calculated for chromium. These calculations are summarized in Table 111. The data used in these calculations are as follows kelley13 (F° - E°°/T ) Speiser, et al H (F° - E°°/T ) 010 where F" — standard free energy at temperature T It was necessary to calculate the total pressure above the alloys from the total weight loss W of the cell during a run, because of the fact that all attempts to collect and analyze the chromium and iron vapor effusing from the cell in the apparatus available failed. The failure resulted from the re-

Jan 1, 1959

By Robert J. Linney

IN the latter part of the year 1943, it was decided to experiment with diamond-drill blast holes in the Old Bed magnetite mine at the Mineville mines of the Republic Steel Corporation, in sections of the ore body where vertical dimensions were large and where development for sublevel bench stopes had already been done. Other possibilities of application for this drilling method were in the reclamation of old floors and pillars in the pitching folds of the Lower Old Bed ore body and in the reclamation of large vertical pillars in the " 21 " Bonanza-Joker ore body. The cross sections and views of the two ore bodies will show the conditions to which the diamond-drill method has been applied. The Lower Old Bed magnetite ore body is lenticular and dips approximately 30° toward the southwest and strikes generally southeast and northwest. An intensely folded structure, which pitches generally on an axis approximately at right angles to the strike, is continuous from the uppermost old workings down to the present bottom of the mine, and probably continues with depth. On successively lower levels this folded structure becomes greater in vertical dimensions and the two folds are closer together in a horizontal dimension. As shown in Fig. 1, this folded structure gives to parts of the ore body considerable vertical dimensions, which provide areas that were developed for sublevel bench stoping above a slushing drift, as shown in Fig. 2. It was in one of these previously developed sublevel bench stopes, No. 26 on the 1185-ft. level, that the diamond-drill blast-hole method was applied for mining the upper sublevel. The lower sublevel was underhand-bench-drilled to the finger raises of the scram drift below. The roof of this stoping area began to break and spall on the lower sublevel, causing the roof to become inclined. Along the hanging wall of the stope this reached an elevation about half way between the two sublevels. A smooth schistose seam in the hanging wall causes the ore to break away freely. Therefore, if bench mining had been carried on in the upper sublevel, a dangerous condition of poorly supported benches would have resulted. When the drillers were slashing across the sublevel to footwall and hanging wall to make a bench, spalling roof of the opening below would probably have carried away part of the bench, and would have left a dangerous place in which to continue underhand benching. A 6 by 8-ft. raise had been driven between the lower stope and the upper sublevel about 200 ft. from a manway. It was decided to use this raise for a starting cut and to arrange holes as shown in Fig. 3, so that a slot would be opened across the ore body between the footwall and hanging wall. This slot would then be used for the purpose of breaking into the ore; by blasting vertical rings of holes drilled at right angles to the axis of the pitching folds as nearly as possible. Layouts of this slot drilling and the rings adjacent are

Jan 1, 1945

By Robert J. Linney

In the latter part of the year 1943, it was decided to experiment with diamond-drill blast holes in the Old Bed magnetite mine at the Mineville mines of the Republic Steel Corporation, in sections of the ore body where vertical dimensions were large and where development for sublevel bench stopes had already been done. Other possibilities of application for this drilling method were in the reclamation of old floors and pillars in the pitching folds of the Lower Old Bed ore body and in the reclamation of large vertical pillars in the "21" Bonanza-Joker ore body. The cross sections and views of the two ore bodies will show the conditions to which the diamond-drill method has been applied. The Lower Old Bed magnetite ore body is lenticular and dips approximately 30° toward the southwest and strikes generally southeast and northwest. An intensely folded structure, which pitches generally on an axis approximately at right angles to the strike, is continuous from the uppermost old workings down to the present bottom of the mine, and probably continues with depth. On successively lower levels this folded structure becomes greater in vertical dimensions and the two folds are closer together in a horizontal dimension. As shown in Fig. I, this folded structure gives to parts of the ore body considerable vertical dimensions, which provide areas that were developed for sublevel bench stoping above a slushing drift, as shown in Fig. 2. It was in one of these previously devel-oped sublevel bench stopes, No. 26 on the 1185-ft. level, that the diamond-drill blast-hole method was applied for mining the upper sublevel. The lower sublevel was underhand-bench-drilled to the finger raises of the scram drift below. The roof of this stoping area began to break and spall on the lower sublevel, causing the roof to become inclined. Along the hanging wall of the stope this reached an elevation about half way between the two sublevels. A smooth schistose seam in the hanging wall causes the ore to break away freely. Therefore, if bench mining had been carried on in the upper sublevel, a dangerous condition of poorly supported benches would have resulted. When the drillers were slashing across the sublevel te footwall and hanging wall to make a bench, spdlling roof of the opening below would probably have carried away part of the bench, and would have left a dangerous place in which to continue underhand benching. A 6 by 8-ft. raise had been driven between the lower stope and the upper sublevel about 200 ft. from a manway. It was decided to use this raise for a starting cut and to arrange holes as shown in Fig 3, so that a slot would be opened across the ore body between the footwall and hanging wall. This slot would then be used for the purpose of breaking into the ore, by blasting vertical rings of holes drilled at right angles to the axis of the pitching folds as nearly as possible. Layouts of this slot drilling and the rings adjacent are

Jan 1, 1946

By D. L. Katz

The Oklahoma City Wilcox sand, discovered on March 26, 1930, has produced 394 million barrels of crude oil and 819 billion cubic feet of natural gas as of July I, 1941. The 100,000-bbl. wells, pressures of 2600 lb. per sq. in., and flows of "Wilcox" sand caused exciting moments in the early life of the field. Today the reservoir is substantially at atmospheric pressure and produccs 75,000 bbl. of crude oil daily through 466 pumping wells. Early estimates of the initial crude-oil content of the "Wilcox" sand1 indicated that about 600 million barrels of crude oil would remain after the pumping wells ceased to produce economically. The Oklahoma City Wilcox Secondary Recovery Association was organized in March 1939, to study the possibilities of recovering a portion of this oil. Only a very brief summary of the information available can be presented in a paper of this nature. Some simplifications and generalizations are necessary to give the over-all picture in SO short a space and statements made may not apply to a specific well or small area. Since the area under consideration by the Association is that north of the south line of section 22-11-3, some information will be presented for areas A, B, C, 1, 2, 3 and part of 4 of Fig. 2, and some will be for the entire Wilcox zone west of the fault. This paper is essentially an abstract of an engineering report made by A. D. Small, B. T. Murphree, M. C. Sons and the author for the Oklahoma City Wilcox Secondary Recovery Association on Sept. 5, 1940. Some information is taken from a report to the Association by C. V. Sidwell on March I, 1940, and some data are from a recent report by A. D. Small. It gives a brief history of the Wilcox zone, estimates of the initial oil contents of the reservoir, present conditions in the reservoir, and probable results from several programs of "secondary recovery." History of Wilcox Zone The Wilcox sand lies on the flank of the general structure, as shown by cross section of Fig. I2,3,4 and areal map of Fig. 2. The sand is of Ordovician age and is composed of well assorted, rounded sand grains with no apparent cementing material. The loose texture of the sand is shown by the enormous quantities of sand production from the wells and from the soft cores. The productive sand varies from zero thickness on the east to 220 ft. maximum and to zero thickness on the west because of water. The development of the pool4 as dependent upon drilling restrictions within the city limits, which accounts for the spacing of drilling operations listed in Table I by years. In 1931, areas I through 7 of Fig. 2 were open for drilling with the exception of some west-edge properties, and all wells drilled before Feb. I, 1935, were in this portion of the field. Nearly all wells drilled from 1933 to 1037 were in areas A, B and C. Since 1939, the newly drilled wells have gradually enlarged the producing area toward the west in the northern portion.

Jan 1, 1942

By D. L. Katz

The Oklahoma City Wilcox sand, discovered on March 26, 1930, has produced 394 million barrels of crude oil and 819 billion cubic feet of natural gas as of July I, 1941. The 100,000-bbl. wells, pressures of 2600 lb. per sq. in., and flows of "Wilcox" sand caused exciting moments in the early life of the field. Today the reservoir is substantially at atmospheric pressure and produccs 75,000 bbl. of crude oil daily through 466 pumping wells. Early estimates of the initial crude-oil content of the "Wilcox" sand1 indicated that about 600 million barrels of crude oil would remain after the pumping wells ceased to produce economically. The Oklahoma City Wilcox Secondary Recovery Association was organized in March 1939, to study the possibilities of recovering a portion of this oil. Only a very brief summary of the information available can be presented in a paper of this nature. Some simplifications and generalizations are necessary to give the over-all picture in SO short a space and statements made may not apply to a specific well or small area. Since the area under consideration by the Association is that north of the south line of section 22-11-3, some information will be presented for areas A, B, C, 1, 2, 3 and part of 4 of Fig. 2, and some will be for the entire Wilcox zone west of the fault. This paper is essentially an abstract of an engineering report made by A. D. Small, B. T. Murphree, M. C. Sons and the author for the Oklahoma City Wilcox Secondary Recovery Association on Sept. 5, 1940. Some information is taken from a report to the Association by C. V. Sidwell on March I, 1940, and some data are from a recent report by A. D. Small. It gives a brief history of the Wilcox zone, estimates of the initial oil contents of the reservoir, present conditions in the reservoir, and probable results from several programs of "secondary recovery." History of Wilcox Zone The Wilcox sand lies on the flank of the general structure, as shown by cross section of Fig. I2,3,4 and areal map of Fig. 2. The sand is of Ordovician age and is composed of well assorted, rounded sand grains with no apparent cementing material. The loose texture of the sand is shown by the enormous quantities of sand production from the wells and from the soft cores. The productive sand varies from zero thickness on the east to 220 ft. maximum and to zero thickness on the west because of water. The development of the pool4 as dependent upon drilling restrictions within the city limits, which accounts for the spacing of drilling operations listed in Table I by years. In 1931, areas I through 7 of Fig. 2 were open for drilling with the exception of some west-edge properties, and all wells drilled before Feb. I, 1935, were in this portion of the field. Nearly all wells drilled from 1933 to 1037 were in areas A, B and C. Since 1939, the newly drilled wells have gradually enlarged the producing area toward the west in the northern portion.

Jan 1, 1942

By R. P. Rothwell

Jan 1, 1885

By Joseph Hyde Pratt, Douglas B. Sterrett, CHAPEL HILL

I. DESCRIPTION. MONAZITE is one of the minerals which, for a long time, was considered rather rare in its occurrence, but, upon a commercial demand arising for it, prospectors and engineers soon located large deposits of it in the Carolinas and Brazil, and the supply has always been able to meet the demand. During 1908 further sources of supply of monazite have been discovered and developed in Idaho. North and South Carolina, however, are the only States that have thus far put any monazite on the market. Monazite is essentially an anhydrous phosphate of the rare-earth metals, cerium, lanthanum, and didymium (Ce, La, Di)PO;. There is nearly always present a varying but small percentage of thoria, ThO2, and silicic acid, SiO, which are very probably united in the form of a thorium silicate, ThSiO4 Some monazites contain but a fraction of a per cent. of thoria, while others have been recorded that showed the presence of from 18 to 32 per cent. ; but the majority contain from 3 to 9 per cent. of this oxide. It is the presence of the thorium oxide that gives the monazite its commercial value. The analysis occasionally shows also the presence of other constituents, as the yttrium and erbium oxides, zirconia, alumina, magnesia, lime, iron oxides, manganese oxide, and titanium oxide. Monazite is light-yellow, honey-yellow, reddish-, brownish-, or greenish-yellow in color, with a resinous to vitreous luster, and is translucent to subtransparent. It is brittle, with a conchoidal to uneven fracture, and is from 5 to 5.5 in hardness, and from 4.64 to 5.3 in specific gravity. It crystallizes in the monoclinic system, and some crystals have been observed that were 6 in. in length. The more perfect crystals are, however,

Jun 1, 1909

By Edward H. Bzirdick

THE territory under particular consideration in this article comprises portions of La Plata and Montezuma Counties, situated in the southwestern corner of Colorado, and around the base of the La Plata Mountains. (See Fig. 1.) In southeastern Utah and northeastern Arizona there are several mountain systems whose origin and structure are practically identical with the La Platas so that ore occurrences found in the latter can be hopefully looked for in the former. With this assumption, there is an area around the laccolithic ranges which offers promise for a successful exploration for gold ores. Ore occurrences of the Silverton, Telluride, Rico, or Ouray Districts will not be discussed, although in these areas the Mesozoic sediments are more or less involved within the ore-bearing complex. These have been intensively studied and developed. The idea is to set forth what my mining experience has been within the largely unaltered . Mesozoic horizon which remains around the extreme bases of the La Plazas. This, until recent years, has been almost entirely neglected by prospectors and operators and, so far as similar territory in Utah and Arizona is concerned, so remains.

Jan 1, 1934

By B. A. Stainton, John D. Gill

OUR combined economic activities have as their goal the maximum of individual well-being and national security. In this age of intense international competition the two objectives are closely related. For many decades, the maximum of well-being and ability to maintain national security have moved generally upward. The best single measure-perhaps the only adequate measure -of the level of the rising goal is the per capita real national income (national income corrected for price changes). For centuries before the industrial revolution the income of the world's population changed little from generation to generation. In our country prior to 1800 the growth of national income was hardly measurable from decade to decade. Since 1850, perhaps since the "industrial revolution," the growth of per capita real income has been increasing geometrically. Of major importance is the accelerative growth of the productive ability of our economy. Inadequate consideration of its implications is partly responsible for periodic delays in solving our princi-

Jan 1, 1946

By A. L. Holley

THIS process is performed in the Pernot puddling furnace; it removes from 75 to 80 per cent. of the phosphorus, most of the sulphur, and practically all the silicon, from crude iron, in from five to eight minutes. It has been in regular use since March, 1877, and has prod uced over seventeen thousand tons of washed metal for the open-hearth furnace. During two years, nearly all, and lately, all the open-hearth steel produced in these works has been made from about 5 tons of washed pig and 2 tons of scrap per open-hearth furnace heat. There are 12 open-hearth furnaces, of which 4 to 9 are running, according to the state of orders. A large amount of highly phosphoric iron from France and Belgium has been also washed and then puddled for parties who have taken, or are expected to take, licenses. The washing of pig for puddling, however, is not a practice at Krupp's works, because pure pigs are nearly as cheap as impure ones. The author and his assistant, Mr. Laureau, spent, during the last month, three days at Krupp's works, examining this process. They copied out of the office books characteristic analyses and physical tests, some of which are given herewith. They also brought hone many samples of pig, cleaned metal, puddle bar, and steel, which they saw treated. Analyses of some of these samples appear in Table IV. As there are no blast furnaces at Essen, the iron is melted in two Bessemer cupolas with fore-hearths; they melt 12g pounds of iron with 1 pound of coke. The metal is run by a spout from the fore-hearth into an opening at the side of the main door of the washing-furnace. The Washing furnace.-This is a regenerative gas furnace. It has a Pernot revolving-hearth of 12 feet external diameter and 3 feet depth. (See Plate.) The four regenerator chambers have 780 cubic feet capacity, which is about the same as the average regenerator capacity of open-hearth steel furnaces of equal tonnage. The lining is 13 inches thick on the sides and 9 inches on the bottom, thus giving a hearth 9 feet 10 inches by 2 feet 3 inches deep. The lining is composed of lumps of highly refractory ores

Jan 1, 1880

By A. L. Holley

This process is performed in the Pernot puddling furnace; it removes from 75 to 80 pel. cent. of the phosphorus, most of the sulphur, and practically all the silicon, from crude iron, in from five to eight minutes. It has been in regular use since March, 1877, and has produced over seventeen thousand tons of mashed metal for the openhearth furnace. During two years, nearly all, and lately, all the open-hearth steel produced in these works has been made from about 5 tons of washed pig and 2 tons of scrap per open-hearth furnace heat. There arc 12 open-hearth furnaces, of which 4 to 9 are running, according to the state of orders. A large amount of highly phosphoric iron from France and Belgium has been also washed and then puddled for parties who have taken, or are expected to take, licenses. The mashing of pig for puddling, however, is not a practice at Krupp's works, because pore pigs are nearly as cheap as impure ones. The author and his assistant, Mr. Laureau, spent, during the last month, three days at Krupp's works, examining this process. They copied out of the office books characteristic analyses and physical tests, some of which are given berewith. They also brought home many samples of pig, cleaned metal, puddle bar, and steel, which they saw treated. Analyses of some of these samples appear in Table IV. As there are no blast furnaces at Essen, the iron is melted in two Bessemer cupolas with fore-hearths; they melt 124 pounds of iron with 1 pound of coke. The metal is run by a spout from the forehearth into an opening at the side of the main door of the washingfurnace. The The washing-furnace.—This is a regenerative gas furnace. It has a Pernot revolving-hearth of 12 feet external diameter and 3 feet depth. (See Plate.) The four regenerator chambers hare 780 cubic feet capacity, which is about the same as the average regenerator capacity of open-hearth steel furnaces of equal tonnage. The lining is 13 inches thick on the sides and 9 inches on the bottom, thus giving a hearth 9 feet 10 inches by 2 feet 3 inches deep. The lining is composed of lumps of highly refractory ores

Jan 1, 1880

By R. Maddi, I. R. Kramer

The delay time for the initiation of slip was studied in single crystals of a brass, aluminum, and ß brass. A delay time for slip was found in ß brass when the specimens were tested below room temperature; however, one was not found for a brass or aluminum. A general theory for the existence of the brittle transition temperature is proposed. A LTHOUGH a considerable amount of effort has A been devoted to the study of the deformation and fracture of single crystals, the vast majority of the work was concerned with static tests or with tests carried out at relatively slow strain rates. The necessity for the study of a possible incubation time for slip becomes apparent when the various theories which have been postulated for the elucidation of the mechanism of slip are considered. The existence of an incubation period would strongly indicate that slip occurs by a process of nucleation and growth; whereas the absence of an incubation would present rather convincing evidence that slip occurs by a cataclysmic process. In addition to shedding light on the process of plastic deformation, an understanding of the early stages of plastic deformation may be helpful in finding an explanation for the brittle behavior of the body-centered metals under certain conditions. It is well known that these metals, such as iron, molybdenum, tungsten, ß brass, etc., will become brittle as the test temperature is lowered or the strain rate is increased. In spite of the fact that this subject has received considerable attention since the turn of the century, no adequate theory exists today which explains the phenomenon. In the ductile temperature range the metal breaks with a "fibrous" fracture after considerable slip has taken place. In the brittle temperature range the metal fails essentially by cleavage on the {loo) planes: however, some plastic flow is always present even in the most brittle fractures. It is possible, as will be explained later, to ascribe this brittle behavior to the length of the incubation time for slip. Clark and Wood,' using polycrystalline metals, showed that a delay time existed for the yield point in mild steels and that the delay time depended upon the applied stress. These authors stated that the delay time was observed only with those materials for which the stress-strain curve showed a definite yield point. In their work only the mild steel specimens exhibited a delay time at the yield point, while the other materials studied-type 302 stainless steel, SAE 4130 normalized steel, SAE 4130 quenched and tempered steel, 24s-T aluminum—did not show a delay time. These authors' in an extension of their work, found that as the temperature was lowered the delay time was increased. It is, then, the purpose of this investigation to measure or to set an upper limit on the delay time for plastic flow in single crystals of a brass, aluminum, and ß brass. The delay time will also be studied as a function of temperature. The incubation time may be measured by determining the length of time the specimen will support a stress without slip occurring when the stress is greater than the static critical resolved shear stress. In order to accomplish these measurements use was made of a pendulum which was so designed that a single crystal specimen could be placed at various positions along its length. When a pendulum is struck by another pendulum of the same length, an elastic wave is transmitted down the bar with the velocity of sound in the material and is reflected from the far end of the bar. The reflected wave then travels back and unloads the stress until it reaches the impacted end of the bar and the two pendulums separate. The length of time that the specimen is subjected to the stress is equal to the time it takes for the stress wave to travel twice the distance from the specimen to the end of the bar. The stress applied to the specimen is governed by the velocity of impact of the two pendulums. The stress at which the specimen first suffers plastic: deformation was determined in these experiments by examining the specimen under the microscope for the first appearance of slip lines and by measuring the residual strain after each impact. In these experiments the critical resolved shear stress was approached from the low stress side and no attempt was made to determine it exactly. To determine it exactly, it would have been necessary to find that stress at which slip would have just started. However, since the stresses were increased in rather small increments the critical stress is believed to be approached rather closely, as will be seen from the experimental results. The critical stress will be taken as the highest stress obtained before the onset of plastic deformation. The stresses

Jan 1, 1953

By R. S. Bradley

WHAT are known as insulating firebrick are lightweight firebrick with low thermal conductivity designed primarily for use in direct contact with furnace gases. These are a recent development in the refractories industry, and are really an outgrowth of the type of insulating brick suitable for use behind refractory walls developed by the insulation manufacturers. To differentiate between these two types of brick, the manufacturers have recently agreed upon the use of the term "Insulating Firebrick" to apply to the type of brick suited for use in direct contact with furnace gases, and the term "Insulating Brick" for the type suitable for use behind refractory walls. Insulation was applied to steam pipes as far back as 1900. This was a low-temperature insulation, the most common type being magnesia blocks. The next development was applying insulation to the outside of furnace walls, a service which necessitated an insulating material of higher temperature resistance. Natural diatomaceous earth, both in the powdered and brick form, was used; this was efficient and is still used extensively for backing up refractory walls where the inner surface temperature of the insulation does not exceed 1600° F.

Jan 1, 1937

By T. L. CONDRON

DURING the past fourteen months, this committee has had under consideration and study the subject of the licensing or registration of engineers. The fifteen members of the committee as appointed by Council, were selected from thirteen states, viz., Connecticut, New York, Pennsylvania, Ohio, Georgia, Louisiana, Illinois, Missouri, Iowa, Minnesota, Colorado, California and Washington, and therefore represent practically all sections* of the United States, as well as mechanical, electrical, mining, hydraulic, municipal, sanitary, railway and' structural engineering, and also colleges of engineering. The first work of the committee was to investigate the general subject and to collect, so far as possible, avail¬able material bearing upon the subject in hand,. in-' eluding opinions from many engineers as to the need or desirability of legislation, as well as copies of all state laws passed and proposed, having to do with licensing or registration of engineers, architects and surveyor, This preliminary investigation disclosed that very pronounced views were held by engineers throughout the country, both for and against state licensing or registration. The general sentiment one year ago was more opposed to such measures than it is today. The older members of the profession did not as a rule favor licensing nor did they feel there was need for state regulation of engineering practice, while among the younger men there was a feeling that licensing or registration by the states would add prestige to professional engineers and in many ways benefit -the profession, as well as individual engineers.

Jan 1, 1920

By Louis R. Hodell

WHEN the drilling of an oil well is completed a permanent opening from the reservoir to the surface must be provided. This is done by lining the hole with pipe, commonly known as casing. In the past, all but a small amount of casing has been run in the hole and joined by threads and couplings. Recently, however, in California, Texas, and Oklahoma, there has been a definite tendency 'to adopt -the welded joint for the following reasons: (1) Plain end casing for welding may be bought for 15 per cent less than thread-and-coupled casing; some of this is offset by the cost of welding the pipe in the hole but a respectable net profit remains.

Jan 1, 1937

By Oliver M. W. Sprague

THIS gold problem is full of complications and can hardly be handled adequately or comprehensively in any short period of time. Perhaps I might begin by mentioning a few aspects of the subject about which I suppose there will be no disagreement. The first of these is that we already have a stock of monetary gold in the United States far in excess of what is needed to support any desirable increase in the present volume of currency and credit. The second is that this already superabundant gold stock is certain to be considerably enlarged during the course of the war, and presumably during the months of readjustment following its conclusion. Some billions of additional gold, we may reasonably presume, will come into the country during these next few years, thus increasing the aggregate monetary gold stock from the present eighteen billions to perhaps twenty- two or even twenty-five billion dollars.

Jan 1, 1940