Search Documents

By J. C. Reed, J. M. Hansell

Cinnabar was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigell by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done considerable exploration work and has retorted the high-grade ore so obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district. In March, 1934, the United States Geological Survey began a study of the Arkansas quicksilver district, which was made possible by an allotment of funds from the Public Works Administration. Until

Jan 1, 1935

Cinnabar was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigell by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done considerable exploration work and has retorted the high-grade ore so obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district. In March, 1934, the United States Geological Survey began a study of the Arkansas quicksilver district, which was made possible by an allotment of funds from the Public Works Administration. Until

Jan 1, 1935

By A. L. Blomfield, M. J. Trott

ThE Golden Cycle Mining and Reduction Co. operates its custom mill at Colorado Springs on Cripple Creek ores exclusively. These ores are straight sulfo-tellurides, with practically no base metals such as Pb, CU, Zn, As, or Sb. Upon entering the mill, the ore all passes through the sampler to storage bins, where beds of 5000 tons each are made to insure uniformity in roasting. Classification of ORes For efficiency, it has been found advisable to separate the ores into two classes according to their lime content. Other constituents have their effect, such as alumina and magnesia, but, speaking generally, these are roughly proportional to the lime, which, as CaO, is used as the indicator. Class A contains not more than 2 per cent. CaO and comprises about 66 per cent. of the ore treated. Class B contains over 2 per cent. CaO, and comprises 34 per cent. of the ore treated. Typical analyses of both classes are as follows: Class A a B Insol.......................... 86.70 75.90 Al2O3........................:.. 2.30 3.40 Fe.............................. 3.26 3.48 CaO............................. 1.57 5.12 S............................... 1.79 1.80 MgO........................... 0.21 1.08 Ignition loss..................... 3.20 6.50 99.03 97.28 The beds of each class of ore are made as large as possible with the available ore as it comes in, to avoid changing from one bed to the other any oftener than necessary. Each roaster will handle 50 per cent. more of class A ore than of class B, with practically the same results. This necessitates changing the rate of feed for each new bed and tends toward a poor roast and loss of tonnage at each change.

Jan 1, 1919

By J. C. Reed, J. M. Hansell

Cinnabar was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigell by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done considerable exploration work and has retorted the high-grade ore so obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district. In March, 1934, the United States Geological Survey began a study of the Arkansas quicksilver district, which was made possible by an allotment of funds from the Public Works Administration. Until

Jan 1, 1935

By Wheeler North

THE United Eastern Mining Co.'s property is located in the Oatman, Gold Roads mining district of Mohave County, Ariz. The mine and mill are some 26 mi. (41.8 km.) southwest of Kingman, the nearest railway connection. The ore consists of a mixture of calcite and quartz with some andesite. The values, which are mainly gold, alloyed with approximately 34 per cent., by weight, of silver, are extremely fine so that fine grinding is a most important factor in extraction. The milling process, briefly, consists of single-stage, coarse-crushing, two-stage ball milling in cyanide solution, followed by combined mechanical and air agitation, and by straight counter-current decantation. The Merrill zinc-dust precipitation method is used to recover the values, and is preceded by the Crowe vacuum treatment of the solution. The most notable features of the plant are the absence of filters, and the use of short peb mills loaded with steel balls, for fine grinding. As originally designed, the capacity of the mill was to be 200 tons per day, although the grinding end was to be capable of handling double that amount. By adding extra agitators and thickeners and by some alterations to the grinding end, the daily capacity has been raised to 285 tons. This, it is hoped, may be increased to 300 tons during the warm months of the present year. TONNAGE MILLED PER DAY 1917 average 234 Maximum month 272 Minimum month 146 1918 average 253 Maximum month 276 Minimum month 217 As this article primarily deals with plant operations, those interested in the mechanical description are referred to the article by Mr. Otto Wartenweiler,1 the designing engineer, which gives the details and costs of design and construction. The following changes have been made since that article was published:

Jan 8, 1919

By Sidney Sigel, J. Gardner Brooks, Irvin R. Kramer

In 1942 Grossmannl proposed that the hardenability of a steel may be calculated from its chemical composition by considering the base hardenability associated with its carbon content and grain size and multiplying this base by factors for each element present. Since Grossmann's original publication, several investigaton2-6 have reexamined the multiplying factors for the individual elements and in general have found that the multiplying principle is valid. However, some of the individual factor curves developed have been in poor agreement. Inasmuch as the carbon-factor curve obtained by Grossmann was dependent Lipon the factors for all the other alloying elements present in the steel, it logically followed that his results were in need of correction in the light of the new data available for manganese, silicon, and the other alloying elements. Furthermore, in order to avoid the possibility that errors in the manganese, silicon, or other curves might influence the carbon-factor curve, investigation of iron-carbon alloys containing little or no manganese and silicon was necessary. That the effect of carbon on hardenability was greater than indicated by Grossmann is shown by a comparison of the diameters of completely hardened rounds of iron-carbon alloys with the ideal critical diameter calculated from Grossmann's factors. These alloys have a greater hardenability in a finite quench than predicted by Grossmann's factors for an infinite quench (Table I). Among the other important variables that were in need of further investigation were the effect of deoxidation practice on the grain-size correction curves and the effect of stable carbide-forming elements on the depth of hardening. Most Of the work by Kramer, Hafner, and Toleman4 was done on silicon-killed steels. It was not known whether Gross-mann's grain-size correction curves, determined on aluminum-killed steels, was valid when applied to steels with different deoxidation practice. More data on the

Jan 1, 1947

By J. Gardner Brooks, Sidney Sigel, Irvin R. Kramer

In 1942 Grossmannl proposed that the hardenability of a steel may be calculated from its chemical composition by considering the base hardenability associated with its carbon content and grain size and multiplying this base by factors for each element present. Since Grossmann's original publication, several investigaton2-6 have reexamined the multiplying factors for the individual elements and in general have found that the multiplying principle is valid. However, some of the individual factor curves developed have been in poor agreement. Inasmuch as the carbon-factor curve obtained by Grossmann was dependent Lipon the factors for all the other alloying elements present in the steel, it logically followed that his results were in need of correction in the light of the new data available for manganese, silicon, and the other alloying elements. Furthermore, in order to avoid the possibility that errors in the manganese, silicon, or other curves might influence the carbon-factor curve, investigation of iron-carbon alloys containing little or no manganese and silicon was necessary. That the effect of carbon on hardenability was greater than indicated by Grossmann is shown by a comparison of the diameters of completely hardened rounds of iron-carbon alloys with the ideal critical diameter calculated from Grossmann's factors. These alloys have a greater hardenability in a finite quench than predicted by Grossmann's factors for an infinite quench (Table I). Among the other important variables that were in need of further investigation were the effect of deoxidation practice on the grain-size correction curves and the effect of stable carbide-forming elements on the depth of hardening. Most Of the work by Kramer, Hafner, and Toleman4 was done on silicon-killed steels. It was not known whether Gross-mann's grain-size correction curves, determined on aluminum-killed steels, was valid when applied to steels with different deoxidation practice. More data on the

Jan 1, 1947

By Richard E. Chism

Some years ago, when I was seeking an illusive fortune and gaining a precarious existence in the primeval forests of Brazil, there penetrated, even to my headquarters in that far-off land, the story of a new-found mining district, where mountain peaks were ribbed with silver, and valleys teemed with virgin gold. Such were the stories that caused hundreds of men to seek their fortune in Sierra Mojada, and to return heaping curses, loud and deep, upon the vivid imaginations that had evolved the glittering fiction. Nevertheless, the rumors had some foundation of truth. The ribs of silver exist, if not the placers of gold; and a flourishing town, of some three thousand people, with two leading mining companies and several smaller ones, in operation, represents what was permanent in the excitement of 1879. Geographical Situation. The town of Sierra Mojada is situated in the State of Coahuila, Republic of Mexico, in latitude 27' 24' N., and longitude 26' 40' W. of Washington, 4' 36' W. of the City of Mexico, and 103' 43' TV. of Greenwich. It lies about 70 miles, in an air-line, N. E. of Escalon station, on the Mexican Central Railroad; but by the present wagon-road, which makes a long detour to turn the mountain range, the distance to the station is about 105 miles. The nearest towns are Huajuquilla, in the State of Chihuahua, about 125 miles due west, and Cuatro Cienegas, in the State of Coahuila, 112 miles to the eastward. Between these points and the town of Sierra Mojada, and to the north of this town, the country is an immense desert, entirely uncultivated, almost uninhabited, and very little known. This

Jan 1, 1887

By O. P. Arora, M. Metzger

Single-phase aluminum containing 1 to 600ppm copper was studied in 7 to 26 pct HCl. The corrosion rate in the autocatalytic stage was resolved into a constant intrinsic component and an acdelerating autocatalytic component, and attention was focused on the part of this stage where the corrosion rate could be described by a simple empirical relation. Autocatalytic corrosion in this period was localized and its rate increased rapidly with copper content and with the strength and chlaride content of the acid. The effects of adding cupric ion to 16 pct HCI were functionally and quantitatively inconsistent with the autocatalytic rates observed. A theory of these rates was given based on the deposition in nzetallic contact with the aluminum of part of the copper introduced by corrosion. It has long been known in a general way that aluminum containing sufficient copper suffers in hydrochloric acid an autocatalytic acceleration of corrosion resulting from the introduction into the acid of copper ions and their reduction on the specimen as elemental copper, which provides cathodes of low hydrogen overvoltage.'-3 In a previous paper, this phenomenon was identified in single-phase high-purity material at copper levels as low as 20 ppm and an empirical equation describing autocatalytic corrosion rates in 16 and 20 pct HC1 was presented. In the present work the range of acid strength and chemistry studied was extended, a more accurate empirical equation for the autocatalytic rate was determined, and a theory of this rate was formulated. A major source of interest in this system is the intergranular corrosion, which is also strongly influenced by copper content,= and an objective of the present work on general corrosion was to provide a basis for studying the role of copper content in intergranular corrosion, which is experimentally much less accessible.

Jan 1, 1963

By Alden B. Greninger, Victor G. Mooradian

Microscopic examinations of quenched (beta) 60:40 copper-zinc and quenched (beta) 74:26 copper-tin alloys have frequently disclosed long, thin parallel bands or markings within the polyhedral beta grains. Apparently, it has been accepted that these markings are mechanical twin bands, although there is no published account of experimental data that might tend to substantiate this belief for the copper-zinc system, and only meager evidence has been submitted for the copper-tin system. Johnsonl0 commented upon the markings he observed after deforming a quenched brass of 55.6 per cent copper and 44.4 per cent zinc. Clark's papers4 on the heat-treatment of Muntz metal contain many photomicrographs of markings in beta brass; these she referred to as Neumann bands (inasmuch as repolishing and re-etching failed to remove them) and stated that markings present in Muntz metal as quenched were the result of shock imparted during the polishing operation. Van Wert18 first suggested that these parallel markings in quenched beta brass (60:40) might be alpha precipitated along certain crystallographic planes of the matrix lattice. He showed that upon reheating the specimens to temperatures below 800" C., obvious precipitation of alpha within the large beta grains first occurred at the markings. In a discussion of this paper, Phillips stated (pp. 505-507) that in his opinion the markings observed by Van Wert were mechanical twins resulting from contraction strains produced during the quenching operation. In a study of segregate structures in beta copper-tin, Smith17 observed that in the quenched beta phase (containing 74.92 per cent Cu) parallel . bands or markings very similar to those in metastable beta brass could be

Jan 1, 1938

By Alden B. Greninger, Victor G. Mooradian

Microscopic examinations of quenched (beta) 60:40 copper-zinc and quenched (beta) 74:26 copper-tin alloys have frequently disclosed long, thin parallel bands or markings within the polyhedral beta grains. Apparently, it has been accepted that these markings are mechanical twin bands, although there is no published account of experimental data that might tend to substantiate this belief for the copper-zinc system, and only meager evidence has been submitted for the copper-tin system. Johnsonl0 commented upon the markings he observed after deforming a quenched brass of 55.6 per cent copper and 44.4 per cent zinc. Clark's papers4 on the heat-treatment of Muntz metal contain many photomicrographs of markings in beta brass; these she referred to as Neumann bands (inasmuch as repolishing and re-etching failed to remove them) and stated that markings present in Muntz metal as quenched were the result of shock imparted during the polishing operation. Van Wert18 first suggested that these parallel markings in quenched beta brass (60:40) might be alpha precipitated along certain crystallographic planes of the matrix lattice. He showed that upon reheating the specimens to temperatures below 800" C., obvious precipitation of alpha within the large beta grains first occurred at the markings. In a discussion of this paper, Phillips stated (pp. 505-507) that in his opinion the markings observed by Van Wert were mechanical twins resulting from contraction strains produced during the quenching operation. In a study of segregate structures in beta copper-tin, Smith17 observed that in the quenched beta phase (containing 74.92 per cent Cu) parallel . bands or markings very similar to those in metastable beta brass could be

Jan 1, 1938

By H. H. Richardson, E. H. Dix

Of all the alloying elements used in commercial aluminum alloys, copper stands out as by far the most important, and it is perhaps for this reason that the constitution of the aluminum-copper system has received the attention of a number of experimenters covering a period of approximately 20 years. It would be expected that during this time the equilibrium relations would have been thoroughly and exactly worked out. In a general way this is true, but there is a surprising lack of agreement in the details of the high aluminum end of the diagram, particularly in regard to the solid solubility of copper in aluminum, which has been given variously as 2 per cent. to 5 per cent. at the eutectic temperature. The importance of this is much greater than might at first appear to one unfamiliar with modern commercial aluminum alloys. This is true because, with one exception, the susceptibility of the strong alloys to heat treatment depends, in part at least, upon the solid solubility relations of copper in aluminum. In 1919, Merica, Waltenberg, and Freeman1 published the first detailed information on these solubility relations. They found that the solubility of copper decreases with falling temperature from about 4 per cent. at 525" C. to about 1 per cent. at 300" C. and is apparently still diminishing at lower temperatures. In 1921 there was published a brief account of the results obtained in the National Physical Laboratory, Teddington, England.2 This laboratory, however, reported that 5 per cent. of copper is soluble in aluminum at 540" C., and that this amount decreases to about 3 per cent. at 20" C. In the same year Ohtani and Hemmi3 reported a solubility of 4.8 per cent. copper at 520" C., 2.6 per cent. at 460" C. and 1.5 per cent. at 420" C.

Jan 1, 1926

By F. E. Lathe, L. Hodnett

This paper summarizes extensive data supplied by 40 copper converter plants in 18 countries, and includes a partial analysis and comments on the effect of converter slag composition and temperature on the fomzation and elimination of magnetite and the life of basic and neutral refractories. APRELIMINARY draft of this paper, including data from 26 companies which had submitted replies to a questionnaire, was presented at the Annual Meeting of the AIME held in New York in February, 1956. Publication was delayed in the expectation that additional replies would be received, and justification for the subsequent delay may be found in the fact that the present revised paper contains data from 40 converter plants situated in 18 different countries. The suggestion that a questionnaire be sent to the major copper and copper-nickel plants outside the U.S.S.R. and associated countries arose at the Los Angeles Annual Meeting in February, 1953, where several papers dealing with converter construction and operation were presented. In private discussions which followed, a group of metallurgists and refractories engineers raised the question why practices varied so much at different plants. Why did magnesite brick give superior service to chrome-magnesite in some plants but chrome-magnesite prove superior in others? Would metallurgical studies point the way to the development of still better refractories? Could magnetite formation be prevented in converter slags and reverber-atory furnace mattes? If this was feasible, why was a heavy circulating load of magnetite tolerated, when, in all probability, it increased copper losses in the reverberatory slags and, in some cases, made it necessary to shut down the furnaces periodically to clean out the accumulated magnetite? Was the sole purpose of coating brick with magnetite that of

Jan 1, 1959

By K. H. Heino

Two 200 T/da Lurgi Turbulent Layer fluid-bed roasters have been in operation at Canadian Electrolytic Zinc Limited since 1966. Zinc concentrate containing 52-54% Zn, 9-11% Fe,31-33% S is treated to produce calcine containing 60-62% Zn,10-12% Fe, .l-.3% S as sulphide and .8-1.2% S as sulphate. Each roaster train comprises a waste heat boiler, two cyclones in parallel and a two-field electrostatic precipitator. Distribution of calcine collected is 10-15 percent from bed overflow, 55-65 percent from boilers, 20-25 percent from cyclones and 2-6 percent from precipitators. A Monsanto designed contact plant produces acid at a rated capacity of 365 T/da (100% H2304 basis) from roaster gases diluted to 7.0-7.5% S02. The process steps are gas cleaning and cooling by weak acid scrubbing, acid mist removal in electrostatic precipitators, gas drying in 93.5-96.5% H2304, conversion of sulphur dioxide to sulphur trioxide in a four-pass converter containing vanadium pentoxide catalyst, and absorption of the sulphur trioxide in 98.1-98.3% H2S04. Product acid is 93.2% H2S04. Conversion efficiency is 97-98 percent and overall sulphur recovery from concentrate is 87-90 percent. The adjacent fertilizer plant has a capacity of 135 T/da of P205. The products are 54 percent phosphoric acid, run-of-pile triple superphosphate, and diammonium phosphate. The plant is of Ugine-Kuhlman design and consists of an air-cooled multiple tank reactor, a tilting pan filter, and a forced circultation vacuum evaporator. Triple superphosphate is made on a continuous belt and partially cured in a rotary dryer. Diammonium phosphate is produced by ammoniating phosphoric acid in a single stage reactor. The slurry of ammonium phosphate is granulated in a blunger and dried.

Jan 1, 1970

By R. H. Harrington

The definition of precipitation-hardening1 is well understood and its principles have been subjected to study for some time. However, the variation of properties with double aging, combined with strain-hardening, gives promise of new and useful phenomena. Properly to understand these distinctions, definitions of these terms are necessary. Precipitation-hardening1.—This reaction usually depends upon an alloy having such a composition that it consists only, or in major part, of but one phase, a solid solution, at a high temperature, so that, upon slow cooling, this solution breaks down into two phases, the solid solution and a compound. By heating the alloy to the temperature for maximum solution of the compound, quenching, and reheating to a suitable lower temperature for critical dispersion precipitation of the compound, useful properties of the alloy may be developed to a maximum. Double Aging.—Dougle aging in part is similar to the process for precipitation-hardening, consisting of heating a precipitation-hardening alloy to the solution temperature, quenching, reheating to the suitable dispersion precipitation temperature, strain-hardening, and again reheating to a suitable temperature to develop certain useful properties to a maximum. The strain-hardening may be induced by two methods: (I) a rate of cooling from the first reheat may suffice to strain the solid solution lattice of the alloy; or (2) the alloy may be cold-worked to a suitable degree between the two reheats. Pkecipitation-hardening of Copper-cobalt-beryllium Alloys1.2 The composition of principal interest is that of 2.6 per cent Co, 0.4 per cent Be, 97 per cent Cu. The alloy has been developed commercially and, with certain reasonable precautions, ordinary brass-foundry practice suffices to produce an alloy of high quality. Preliminary Precipitation-hardening Study.—Samples were cut from a I-in. round rod cast in a graphite mold. These samples were then

Jan 1, 1937

By R. G. Gifkins

Mean boundary migration depended linearly upon creep extension under various conditions. Prolonged annealing or air-casting increased the proportion of immobile boundaries at a given stage of tests. Grain growth during annealing followed a power law. The linking of migration and sliding in creep and models for migration are examined; activation energies are calculated from these models. Segregation of oxygen to boundaries appears to be a controlling factor. THE idea that boundary migration and boundary sliding during creep are linked has often been suggested,'-5 especially when evidence has been obtained for an alternation between the two processes. In simple bicrystals sliding can occur without any migration6 but in more complex bicrystals7 it is observed. McLean' and Couling and Roberts 5 made measurements of both sliding and migration; McLean concluded that there was no linking of the two processes whereas Couling and Roberts supported the idea. McLean' also developed a model for migration during creep and annealing. The present work was initiated as part of a study of the recrystallization of lead during creep9 but has been extended to examine some aspects of the mechanism of migration. MATERIALS AND METHODS Specially refined high-purity lead* was used; the total of impurities, excluding oxygen, was 0.0008 wt pct. Oxygen was removed as far as possible by melting in vacuo, treating at 550" to 600°C with hydrogen and then casting at 450°C under a vacuum of 10-2 mm Hg; the oxygen was then believed to be 0.00005 wt pct. Specimens were made from extruded strip and then annealed at the required temperature in an air oven, controlled to 5 lac. They were then polished in a mixture of acetic acid and hydrogen peroxide. At this stage some specimens were etched to give grain contrast and their grain sizes determined by the intercept method. Migration of boundaries during creep was measured on the surface of polished (not etched) specimens, directly loaded at room temperature (22°C) or 50°C (52"C) to initial stresses of 300 to 700 1b per sq in. Twenty six vacuum-cast hydrogen-reduced specimens were used and, in addition, two specimens were from material air cast after hydrogen reduction ("partial" air cast) and two from air-cast material not treated with hydrogen ("full" air cast). Duplicates were made in the majority of tests. At intervals through the creep tests, specimens were unloaded and the migration measured, normal to the direction of migration at the point of measurement, for each boundary along standard traverses. Usually between 110 to 180 boundaries were measured at each of some twelve stages of the tests. Migration was measured on the projected image (X100) using prism illumination. Fig. 1 illustrates the method of measurement and shows the kind of variation of migration found from boundary to boundary and along particular boundaries. Fig. 2 gives an example of more extensive migration. The mean value of distance migrated was generally reproducible to *10 pct but occasional points gave a scatter of *20 pct. The correctibn applied by McLean8 to allow for the contribution sliding makes to the apparent distance of migration could not be used, for the sliding at most boundaries was too small to measure with the equipment available. There were two reasons for supposing the correction unnecessary in the present work;

Jan 1, 1960

By John Ward Smith

Dawsonite-bearing oil shale of Colorado's Green River formation offers a unique and vast (more than 5.9 Gt of A120 j) resource of easily extractable alumina. The processing methods required by the thermal reactions of dawsonite and its oil-shale carrier also require production of shale oil, soda ash, and nahcolite as marketable coproducts. These production methods are presented. The alumina production process is contrasted with the Bayer process to describe technical advantages of extraction of alumina from oil shale which may offset the problems associated with processing a relatively lean ore. While alumina production from oil shale requires development of new technology, the technical problems appear solvable. Only the political problems arising from the now onerous and completely unnecessary federal oil-shale withdrawal appear less solvable.

Jan 1, 1982

A New Ingersoll-Rand Turbo Blower The Ingersoll-Rand Co. has added to its Turbo Compressors and Blowers a low-pressure machine t o handle volumes from 3,000 to 35,000 cu. ft. per minute at from 1-2 ½ lb. These are particularly adapted to such service as foundry cupola blowing, atomizing oil for oil burners, supplying blast to heating and annealing furnaces of various kinds, blowing air for water-gas generators, pneumatic conveying and ventilating. They are of the single stage, double flow type and are furnished either electric motor, steam turbine or water wheel driven.

Jan 6, 1916

Jan 1, 1963