Search Documents

By Mark R. Svinkin

This paper deals with application of the wave equation analysis to determine capacities of piles driven in saturated sandy soils. It shows that pile capacity in sandy soils changes with time after the completion of pile driving and depends on the ground water elevation. In saturated sandy soils the setup coefficient ranges between upper and lower curves represented by power functions. For a reliable prediction of pile capacity wave equation input should be adjusted with soil damping. Back calculation of soil damping from known pile capacity performed for five tested piles shows that skin damping coefficient changes with time in the same manner as the pile capacity and can be represented by the power functions for considered damping models.

Jan 1, 1995

By Shiou-Chuan Sun

THE fact that coals of different ranks and even of the same rank differ greatly in their amenability to froth flotation is well known. In recognition of the need for an explanation of this phenomenon, two hypotheses have been suggested. Wilkins1 reported that the floatability of coals increased with an increase of the carbon content or rank. This postulate is handicapped by the fact that bituminous coals that possess moderate carbon contents are actually more floatable than anthracite coals that have high carbon contents, as shown in columns 6 and 9 of Table I. Taggart and his associates' implied that the difference of floatability between bituminous and anthracite coal was caused by the variation of carbon-hydrogen ratio. This is not applicable to the relative floatability of other coals and carbons. For example, column 11 of Table I shows that the carbon-hydrogen ratios of low-floating lignitic coal and non-floating animal charcoal are not only smaller than the moderate-floating anthracite coal, but are also similar to the high-floating bituminous coal. Furthermore, according to this hypothesis, high temperature coke-A (464), Ceylon graphite (1238), and lamp-black (357), all possessing extremely high carbon-hydrogen ratios, should be less floatable than other substances having much lower carbon- hydrogen ratios such as high volatile-B bituminous coal (11.9 to 22), anthracite coal (35.7 to 60.5), lignitic coal (15.6 to 33.6), and charcoal (13 to 26.2). However the former group is actually more floatable than the latter group.

Jan 1, 1954

By I. Nakatsugawa

Chemical conversion coating is a process to create thin oxide/hydroxide film containing several inorganic/organic compounds by way of chemical deposition reaction. In case of the application to Mg mobile electronic housings, the film should possess a good electric conductivity while keeping adequate corrosion resistance and working as a paint base. The use of toxic/hazardous chemicals is strictly prohibited from the environmental aspects. This paper describes the recent trend of conversion coating used for Mg electronic housings and analyzes critically from the point of surface technology. The importance of cleaning process and understanding of surface microstructure are particularly emphasized with several experimental results.

Jan 1, 2006

By W. R. Crank

[Rock bursts are phenomena associated with mining operations, particularly with deep mining, although they occur throughout a wide rump, of depth, from 600 feel downward. The intensity is usually in direct proportion to the depth, varying from a loosening and sloughing off to a violent rupture, giving rise to the term, "explosive rock." The more or less violent breaking of rock in mine working, tins been variously designated as " flaking," "pressure hoists," "strain bursts," "bumps," "quakes," and "air blasts," which indicate opinions as to cause and effect. The term "air blast" lots probably beat most widely used, and naturally so, as a more or less rapid movement of air often accompanying the more violent phenomena of rock failure. Furthermore, there is an implied if not definitely expressed degree of magnitude in the action designited by a given term and in the cause and character of the action. For example. flaking, pressure bursts, and quakes are terms ranged to indicate action of increasing magnitude; and pressure bursts, strain bursts. bumps, and quakes are ranged according to the cause and character of the action.]

Jan 1, 1929

By B. M. England, C. Y. Yang, L. T. Matthews, J. Y. Yin

The domestic concentrate used by the Shanghai Meishan Metallurgical Corporation in Nanjing contains significant siderite, magnetite and haematite, the siderite having a substantial influence on its sintering behaviour. On the basis of experimental findings and published information it is proposed that siderite decomposition starts at c.400 degrees C and results in the formation of CO and/or H2, which then reduces the haematite to magnetite prior to the initiation of high-temperature sintering; inter-mixed particles of Australian haematite and pisolite ores also undergo significant reduction. As the gaseous reduction process is so effective, low-temperature forms of silico-ferrite of Ca and Al (SFCA) cannot form even at high sinter basicity. The bench-scale results were confirmed in a pilot-scale facility whose sinters consisted mainly of magnetite, high-temperature SFCA and glass, which is typical of sinters formed from mixes with high magnetite levels

Aug 1, 1995

By Eleanor Abshire

[THE INCREASING use of hafnium as a vital component in atomic power reactors has brought this metal into recent prominence. A literature survey was made and this bibliography was compiled to provide research and production groups with a ready source of reference to this important metal anti its compounds. This service is rendered by the Zirconium Information Center, which is sponsored by the Department of the Navy, Bureau of Ships, and the F .S. Department of the Interior, Bureau of Mines, tit the Bureau's Northwest Electrodevelopment Experiment Station, Albany, Oreg. The following reference sources have been reviewed for this compilation : Chemical Abstracts; Industrial Arts Index; Crerar Metals Abstracts; Nuclear Sciences Abstracts; Bureau of Mine; Information Cicular 7771, Bibliography of Zirconium; anal Bureau of Mint' Information Circular 7830, Bibliography of Zirconium, suppllement to Information Circular 7771.]

Jan 1, 1960

By R Shaw, M Hidding

The design of primary sample cutters for high-capacity conveyors is critical to achieving a correct sample, both in collecting the sample and ensuring smooth sample discharge flow. Modelling usually occurs at the design stage and requires extensive experience to achieve the correct result. However, it is difficult to confirm the effectiveness of the cutter design until after installation. Even with high-speed video, confirmation of complete sample capture is difficult, especially if the material characteristics change over time. Recent investigation using discrete element method (DEM) simulation to model the flow of the ore into the cutter and observe how it interacts with the cutter has revealed some interesting design requirements not observed in the past. By including DEM modelling, the correct design and optimisation of the cutter can be more accurately determined prior to commissioning.CITATION:Hidding, M and Shaw, R, 2017. Modelling ore flow in the design of high-capacity sample cutters, in Proceedings Eighth World Conference on Sampling and Blending , pp 145–150 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Svend [Bue] Rondum

The final report contains a summary of the work performed under this contract, In addition to the report itself, other products were derived from this effort. Several hardware items were prototyped for use with underground belt conveyors, and a manual for installation and maintenance procedures was developed and published under separate cover. Recommendations have been included for implementation of the tools and the manual or, an industry-wide basis.

Jan 1, 1982

By H. E. Bartlett

In the operation of some flotation plants treating platinum ores it was found that there were imbalances between the inputs and outputs. The inputs and outputs were sampled as slurries and it was determined that the imbalances arose from biases in the sampling, despite the samplers having been designed according to well-established rules. The launders feeding the sample cutters, and the sample cutters themselves were redesigned using finite element analysis to model the flows. A new set of design rules were formulated. The application of a Components of Variance Analysis, to determine the variance of primary and secondary sampling and of analysis in the lab for a concentrate is presented to illustrate the need for frequent sampling of process streams.

Jan 1, 2002

By K. U. Kainer, A. Stark, D. Tolnai, M. Hehenberger, C. L. Mendis, N. Schell, N. Hort

Samples of an as extruded Mg-6Zn-0.6Zr-0.4Ag-0.2-Ca (wt.%) alloy was compressed at room temperature and at 250°C. The in situ deformation tests were performed at the P07 (HEMS) beamline of PETRA III, DESY, with a modified DIL 805 A/D dilatometer with to Kapton windows on the sides and the induction coil opened for the beam to transmit the sample. The deformation rate was 10-3 s-1 the samples were deformed to failure. The diffraction patterns were recorded every 3 s with a Perkin Elmer 1621 Flat Panel Detector. The results reveal that different deformation mechanisms are activated during compression at a given strain value. At room temperature twinning is the dominant deformation mechanism, while at elevated temperature dynamic recrystallization occurs while the contribution of twinning to deformation is significantly reduced. The compressed samples were further investigated with conventional metallography and SEM-EBSD to determine the volume fraction, the type of twinning and the strain retained within the grains. The parallel testing of pure Mg samples under the same conditions allows comparison of the compression behaviour of the ZKQX alloy with Mg.

Jan 1, 2014

By D. E. Wolfson

As part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests. According to the estimate of reserves by Dowd,3/ the recoverable coal in Raleigh County in beds 28 inches or more thick, in thousand tons, is: [ ]

Jan 1, 1957

By Agne Rustan

The 9th International Symposium on Rock Fragmentation by Blasting was held in the Granada Conference Centre, Granada, Spain from the 14th - 17th September 2009. The Symposium was preceded by a 1 ½ day Workshop on “Vibrations from Blasting” organized by the initiator Dr. Alex Spathis and his colleague M. J. Noy, both employed at Orica Mining, Australia. Prof. Josè Sanchidrian at the “Universidad Politécnic de Madrid” in Madrid, Spain was the main organizer for both the Workshop and the Symposium. A record number of participants came (292) from a record number of countries (41). There were a total of 14 papers in the Vibrations from Blasting Seminar and 96 papers and 2 Keynote Addresses in the Fragblast 9 Symposium itself. The aim with this paper is to present some results from Fragblast 9 which are of interest for a large target group. One very important result from the Fragblast 9 meeting was that it was decided there that Fragblast 10 will be held in November 2012 New Delhi India.

Jan 1, 2009

By Christian Roche

Our study is focused on the sub-assembly con-tact shoes, pressure rings and pressure bellows. We were keen to mainly study [ ] 1.The contact shoe design 2.The most efficient pressure to ensure an optimal electrical contact between the contact pad itself and the casing 3. The contact shoe cooling circuit in view to provide to the shoe the best mechanical and electrical characteristics in order to bring to the users of COFOR® components a new standard in process setting technical solutions. A finite elements simulation, combined with a thermal and structural studies were used. Our presentation which follows is dedicated exclusively on the influence of the contact shoe cooling system on the process through a thermal and structural analysis. [ ]

Jan 1, 2007

By David E. Fogelson

One model each of three different makes of portable displacement seismographs was calibrated on a shaking table capable of 5,000 pounds of force, Calibration tests were conducted in the frequency range of 5 to 200 c.p,s, and in the amplitude range of 0,002 to 0.05 inch peak-to-peak, The seismographs were tested under two mounting conditions: (1) The feet of the instrument were bolted to the shaking table, and (2) the feet were resting on emery cloth affixed to the table, The results of these tests show that, in the frequency range of 5 to 40 c.p,s, and for vibration levels less than 0.2 g, the magnification for all three instruments is constant with input level but varies slightly with frequency. For vibration levels greater than 0.4 g. and for frequencies greater than 40 c.p.s., the magnification of all three instruments shows large variations with frequency and amplitude of table motion.

Jan 1, 1962

By J. R. Allsup

Air pollutants in exhaust gas produced from LP-gas (propane) were studied using both laboratory engines and vehicles. The objective of the study was to evaluate engine parameters relating to the advantageous use of propane as a low-pollution fuel. Some comparisons are made between gasoline, natural gas, and propane. Results show that engines can operate over a wider range of A/F with minimum carbon monoxide and hydrocarbon emission when using propane than when using gasoline. Mixture enrichment using propane is unnecessary during cold starts, thereby eliminating the emission penalty during warmup. Carbon monoxide and hydrocarbon emission using propane are unaffected by ambient temperature. The photochemical reactivity of hydrocarbon emission is considerably lower with propane than with gasoline.

Jan 1, 1972

By C. Bazin, D. Hodouin

"A flexible model involving perfect mixers, stagnant zones, plug flow, material bypassing and recycling zones has been developed for interpreting mixing phenomena in mineral processes. The mixing properties are described by the residence time distributions which can be subsequently interpreted by the flexible model. User-friendly computer programs (for 1MB-PC or compatible) have been developed for simulation and modelling of RTDs using the proposed model. Seven mineral processing case studies are discussed in terms of experimental procedure, model calibration results and application of the estimated mixing model to process modelling, diagnosis, and performance evaluation. IntroductionIn any mineral processing plant there are continuous-flow machines that transform or separate the ore components. Grinding mills, flotation cells, conditioning and leaching tanks are examples of such machines. The performances of these vessels or reactors are controlled by the rate at which the reaction proceeds and the time spent in the environment where the reaction occurs. This paper deals with the latter aspect of mineral processes operation.Since most of the reactions occurring in mineral processing units are time dependent, knowledge of the residence time of the material in process vessels is important for modelling and diagnosis purposes. Due to the random mixing phenomena involved in the process equipment, there is a distribution of the residence time of the ore particles and the fluid in the vessel. The probability density function E(t) that a micro-element of the material flowing through a processing unit stays a time t in the vessel, is the residence time distribution (RTD) of the corresponding component."

Jan 1, 1988

By Roy Peratrovich

An innovative cost-saving design for a 1,100 ft bulkhead on the Tanana River at Nenana in central Alaska won Alaska Construction & Oil magazine's Construction Achievement Award. The designers utilized materials available nearby at low cost. They planned sheet pile enclosures, self-anchored back into shore without cell closures. They made it practical for inexperienced local workers to do the building. And they completed the project on time and below a reduced budget.

Jan 1, 1985

By John Feddock

A recent increase in energy demand has resulted in the rapid growth of coal consumption in the People?s Republic of China (PRC), which is the largest coal producer and consumer in the world. Reportedly, the safety issues in Chinese coal mines have been improving, but the number of fatalities and serious injuries continues to be alarmingly high. The number of fatalities from catastrophic accidents have prompted researchers to review the Chinese mine safety situation and to look for potential solutions. Marshall Miller & Associates, Inc. (MM&A), along with various collaborators, has investigated these issues as part of its work on various projects in the PRC and has discussed the concerns with relevant Chinese officials. Preliminary investigations by MM&A of coal mine accidents during 2001?2006 in the PRC indicate that 65%-78% of the total fatalities were the result of gas explosions and roof falls in underground mines. Even though the drainage of methane has been practiced for decades, current practices do not always produce satisfactory results due to technical constraints and equipment limitations. Based on prior experience of in-seam degasification at the Daning Coal Mine located in Shanxi province, MM&A believes that in-seam directional drilling technology can be a viable solution to degas the low-permeability Chinese coal deposits. This paper 1) reviews current Chinese coal mine safety conditions, 2) analyzes the advantages/disadvantages of current degasification practices in China, and 3) presents the pre-mining degasification practices for the longwall panel at the Daning Coal Mine.

Jan 1, 2007

By Jürgen Kretschmann

According to the model of product life cycles, the global coal mining industry is in the stagnation phase. The coal demand of the main consumer, China, has peaked in 2013 and is slowly declining. The Norwegian sovereign wealth fund, the world’s largest, has excluded coal-related companies for ethical reasons. Important players like the UN or the EU have already begun to describe pathways towards decarbonization. Increasing competition between coal mining companies and the mining regions can be expected worldwide if companies want to keep their positions on the global and national coal markets. Companies will focus on the best deposits. European countries like France, Spain, or Germany are only forerunners of this development—their centuries of coal production have been finished. The concept of sustainable development (SD) is fundamentally based on a model of progress where ecological, economic, and social dimensions should be developed equally and positively. But without the idea of competition, the concept of SD is incomplete. Questions arise, such as how can SD be realized on stagnating or declining markets without guarantees for companies “to live forever”? How can SD be a corporate goal in a phase of decline? How can declining mining regions sustainably progress into a better future? The German hard coal mining industry’s lifecycle has ended in 2018 after 60 years of stagnation and decline. As of 2019, all hard coal consumed in Germany will be imported, especially from Colombia, Russia, and South Africa. What has been done in Germany to handle the coal decline in a sustainable way and the lessons learned from this process is described in this paper. It may be useful for mining regions who will face a similar future sooner or later.