Search Documents

Ventilation network modeling in mine planning dates back at least three decades, but it is not widely accepted and/or practiced until the last decade, thanks to the advent of modern computers with their increase d speed and storage space. There are at least half a dozen such modeling software packages available on the market each with different features and acceptance. This paper compares five popular software packages,?? VnetPC Pro, MineVent, VentSIM Visual, VentGraph and MFIRE 3.0. A case study using Missouri S&T?s Experimental Mine is conducted to compare the five software packages in features, interface, output display and user-friendliness.

Jan 1, 2012

By A. J. Kraemer

The properties of crude petroleum continue to interest the Bureau of Mines and constitute an important phase of its major studies on the mineral resources of the United States. The Bureau's interest in the subject has been intensified by frequent requests for information on the characteristics of crude petroleum from various producing fields. Since its inception the Bureau of Mines has collected and analyzed samples of typical oils and at present has surveyed and classified crude petroleums from nearly all the known oil fields of the Western Hemisphere. Results of these surveys have been presented in various Bureau of Mines publications. (See bibliography, appendix A, p. 145.) The nature and comparative value of crude oils from various countries and the extent to which these oils may be considered potential competitors for markets are of manifest importance to the petroleum industry in all lands, largely because all crude oils, wherever produced, are either actual or potential competitors for a market with all other crude oils. The numerous discussions of foreign production of oil that have appeared in the technical press in the past indicate the great interest of the United States in this subject.

Jan 1, 1937

By Christopher Mark

Multiple seam interactions are a major ground control hazard in many U.S. underground coal mines. The two most common types are: ? Undermining, where stress concentrations caused by previous full extraction in an overlying seam is the primary concern, and; ? Overmining, where previous full extraction in an underlying seam can result in stress concentrations and rock damage from subsidence. The National Institute for Occupational Safety and Health (NIOSH) has completed a major study aimed at helping to identify the location and likely severity of these interactions. In the course of field visits to mines throughout the U.S., more than 300 multiple seam case histories were assembled into the largest data base of multiple seam case histories ever collected. These data were analyzed with the multivariate statistical technique of logistic regression. The study also employed LaM2D to estimate the multiple seam stresses, ALPS and ARMPS to determine pillar stability factors, and the CMRR to measure roof quality. The study resulted in the development of a computer program, called Analysis of Multiple Seam Stability (AMSS), which can help mine planners to evaluate each potential interaction and take steps to reduce the risk of ground control failure. AMSS first evaluates pillar design by calculating the single seam Stability Factor (SFSS) using ALPS or ARMPS. It also automatically generates a LaM2D analysis that provides the additional multiple seam stress so that the final, multiple seam SFMS can be determined. The second part of the AMSS procedure builds upon the statistical findings that overmining is much more difficult than undermining, isolated remnant pillars cause more problems than gob-solid boundaries, and weaker roof significantly increases the risk of multiple seam interactions. AMSS quantifies these effects and predicts the outcome in terms of three levels of risk: GREEN (where a major multiple seam interaction is considered unlikely), YELLOW (where adding a pattern of cable bolts or other equivalent supplemental support could greatly reduce the probability of a major interaction.), or RED (a major interaction should be considered likely, and it may be desirable to avoid the area entirely).

Jan 1, 2007

By James G. McKelvey

Owners have seen several major tunnel projects in recent years fall victim to a general reduction in the number of bidders as well as an erratic range of pricing. It should be noted though that this is not a universal trend and some projects have seen good competitive bids. Contractual terms and conditions are an important factor in attracting good competition. The Front End documents of tunnel projects have come under increasing scrutiny as tunneling contractors in the U.S. industry are looking much more closely at their risk exposure in the contract terms and conditions. Considering the amount of tunnel construction work upcoming in North America, it is important that General and Special Conditions are put together in a way that provides a reasonable basis to execute the Contract and also provide a fair, balanced and swift way to resolve disputes.

Jan 1, 2008

By E. P. Youngman

Tantalum is a rare element ; estimates indicate that there is less tantalum than gold in the earth's crust . After remaining a laboratory curiosity for many years , it was used to a limited extent and for relatively few years (1903- 1911) for incandescent electric-light -bulb filaments . Another wave of interest in tantalum appeared when its electrolytic-valve action was taken advantage of in charging storage batteries , especially for radio work . Tantalum chargers were eventually displaced by other types of chargers , but for a time they were manufac tured in sufficiently large numbers to create a demand for the metal and to bring about its production on a commercial scale in the United States . As tantalum became available in larger quantities and at substantially lower prices , and as high prices for platinum encouraged the employment of tantalum as a substitute , the metal was put to many new uses . Ferrotantalum was made and sold before the World War , and patents have been taken out for a number of special alloys for industrial purposes , but probably the largest use for the metal to-day is in vacuum tubes .

Aug 1, 1930

By Behrouz Tehrani

The size, complex issues, and requirements to construct large number of tunnels, for a single project, expeditiously, and without exceeding the overall project budget, a program Construction Management (CM) team is highly recommended to be selected early during design process to provide guidance/direction relative to contract packaging and scheduling. This paper is not focused on the project itself, however, the emphasis is on experiences gained from the project. Wishing that some of the strategies described in this paper will be of value to owners of underground project.

Jan 1, 2008

By H. E. James

During the past ten years there has been an upsurge of interest in the development of selective ion exchange resins and solvents, and of ion-exchange and solvent extraction equipment tailored to the special requirements of mineral-processing circuits. It is therefore not surprising that the recent Symposium on Ion Exchange and Solvent Extraction in Mineral Processing, held at the National Institute for Metallurgy (NIM) on 7th and 8th February, 1980, was a resounding success. This Symposium, organized jointly by NIM. Ion exchange and solvent extraction The Symposium on Ion Exchange and Solvent Extraction in Mineral Processing, which was organized jointly by the National Institute for Metallurgy, the South African Institution of Chemical Engineers, and the South African Institute of Mining and Metallurgy, was held in Randburg on 7th and 8th February, 1980. Analytical chemistry The Fifth International Conference on Analytical Chemistry, organized by the Chemical Society, is to be held at Lancaster University, England, from 20th to 26th July, 1980. Coal mining The First International Symposium on Thick and Steep Seam Coal Mining will be held in London from 18th to 21st May, 1980. Mineral processing The XIV International Mineral Processing Congress will be held in Toronto from 10th to 16th October, 1982. The theme of the congress will be 'Worldwide industrial application of mineral processing technology'. Sessions will be held on the following:

Jan 1, 1980

By Li Zhang

Air was blown into the molten slag as oxygen resource during the dynamic oxidation. It was found that the oxidation is not only in favour of Ti components into perovskite phase, but also the increase of slag temperature and decrease of slag viscosity during the dynamic oxidation promote the precipitation and growth of perovskite phase, average crystal size of perovskite phase is 48 µm. The experimental result realizes the selective enrichment of Ti components and coarsening of perovskite phase, perovskite phase can be separated by mineral dressing method.

Jan 1, 2009

By J. D. Miller

The sedimentary western phosphate deposits of Idaho, Montana, Utah, and Wyoming tend to be calcareous and generally carry a significant amount of dolomite along with collophanite. In some cases, such as the Smokey Canyon Mine, Afton, Wyoming, the ore will also contain mudstone, and in this case the aluminosilicate minerals (clay, feldspar, etc.) together with some dolomite are floated from the collophanite in column flotation cells with an amine in order to meet product specifications (31 % P205) (Service et al.). In other cases, such as the SF Phosphates Limited Mine, Vernal, Utah, the ore is treated by traditional fatty acid flotation of the collophanite with mechanical flotation cells (Weber, 1986). Preliminary tests have now been conducted to evaluate air-sparged hydrocyclone (ASH) technology for the flotation of western phosphate ore. For this preliminary study, samples were taken from the hydrosizer overflow stream (18-21 % P205) at the SF Phosphates Limited Plant in Vernal, Utah for scavenger flotation testing with the 2-inch ASH system in laboratories at the University of Utah. Selected design and operating variables are being studied, and the initial results show that satisfactory separations can be achieved by high-capacity ASH flotation at appropriate operating conditions. For example, with single-stage ASH flotation 80% recovery can be obtained with a scavenger concentrate grade of about 26% P2O5. These results are comparable to, or better than, those obtained at SF plant operations with conventional flotation cells and suggest that ASH flotation technology can be used to good advantage in the phosphate industry. Of course, research should be continued to consider other process streams, optimize the separation efficiency, and evaluate larger diameter ASH units.

Jan 1, 1993

By Richard L. Fowler

An automatic steering control system was designed, installed and tested on a coal mine shuttle car. The system utilizes sensors and associated signal processing electronics developed under a previous phase of this contract. The automatic steering system performs the routine guidance functions of turning corners and straight-through tramming. The shuttle car driver retains full authority of speed, braking, load and unload functions and at any time may exercise his option with manual override or steering. Steering information is generated from signals derived from the existing Lateral Guidance sensor subsystem, and all operational features of the previously developed open-loop system are retained. Above ground system tests were conducted in a simulated mine constructed of wood panel ribs. Results were in good agreement with prior hybrid computer simulations undertaken to validate the basic control system over a broad range of conditions and to select system parameter values. The automatic steering system was successfully demonstrated in the above ground simulated mine to USBM technical representatives. Designed to meet USBM permissibility requirements, the system is ready for a Phase II underground testing program. Testing in actual underground mine environment is expected to provide additional data regarding recommended performance improvements and implementation techniques.

Jan 1, 1975

Northern Iron Ltd (NIL) is an Australian listed company that recently brought the historic Sydvaranger open pit Magnetite Mine (the Project) in Northern Norway successfully back into production. NIL made the decision to operate the Project on an owner mining basis, due to limited large scale mining expertise amongst Norwegian mining contractors, a long mine life, a limited range in planned mining rate and to minimise costs. As a new mine operator in a country where labour practices are strictly regulated, there was the desire to reduce the risk associated employing and managing skilled personnel. This was achieved by coupling the purchase of the required mining equipment from the original equipment manufacturer's (OEM) regional dealers with OEM supported Maintenance and Repair Contracts (MARC). This paper examines the process that was followed to implement an owner mining operation in a short time frame; approximately 12 months from the initial requests for quotation to actual delivery of mining equipment to site, and some of the challenges faced. By following a formal and well-tested process, not only was the implementation achieved in the set time frame, but significant value was added through the cost savings achieved in the equipment purchase price and MARC rates that were negotiated through this process.

May 1, 2010

By John Wilson

This report describes the performance of Phase I of a project to design, analyze, and demonstrate a multilift longwall mining method applicable to mining coal seams twelve (12) feet or more in thickness. A non-simultaneous multilift operation is the most viable thick seam mining technique for introduction to the United States coal industry. In the case of the proposed site at Emery, Utah it will result in an increase in coal extraction from 30% with present methods to at least 50% and possibly more. The major technological advance involved in this project is mining a lower lift under a previously mined upper lift. To accomplish this, entries must be developed and maintained beneath the upper lift gob. This will necessitate the use of steel supports at frequent intervals throughout the lower lift' entry system. This has not been done in the U.S. to date. An economic analysis of the project indicates that, while this method will result in a higher than average cost per ton for coal mined, the coal would be competitive with current-operation in the area.

Jan 1, 1976

By Larry A. Lass

The U.S. Bureau of Mines, in cooperation with the Iron Range Resources and Rehabilitation Board, investigated the potential of using northeastern Minnesota papermill waste sludges as a binder for Mesabi Range iron ore (taconite) concentrate. Sludges from five different commercial papermill waste treatment operations were evaluated in laboratory tests. Except for the coarsest sludge, all were fairly easy to blend with the taconite concentrate using conventional mixing methods. The coarsest sludge had to be reslurried at 2 pct solids before adding it to the concentrate in order to obtain pellets without visible sludge clumps. Drying and grinding the sludges made them less effective as binders because of a lower degree of rehydration. On a dry weight equivalent basis, twice as much raw sludge binder was required to obtain similar pellet physical properties as with bentonite; however, the pellets made with raw sludge had superior metallurgical properties. Over 30 pct higher reduction rates and over 1500 C higher softening temperatures were obtained with sludge binder than with bentonite. Sludge D, which had the lowest fiber and the highest alkali metal content, resulted in the lowest reducibility enhancement. Even though more raw sludge was required than bentonite, the sludges have virtually no value, and therefore may provide a cost-effective additive binder for producing improved metallurgical-quality pellets. Large-scale testing has not been done to confirm these laboratory results.

Jan 1, 1989

Grinding Mill Operation and Maintenance - Central to Asset Management Since 2005, RME has pursued a vision for a new grinding plant operational paradigm, made possible by RME's latest Mill Relining Systems. At some sites, new liners degrade SAG mill performance. The variables include mill volume loss, rotational speed limitations (ball strike) and liner designs developed for longer and longer life but without a backward glance at metallurgical consequences of whole plant performance. Freshly relined mills can initially deliver as little as 80 per cent of their maximum throughput, that maximum occurring toward the end of the liners' wear life. RME's proposition is to see new liners designed for maximum commercial performance. This may mean more frequent mill relines but with liners designed to yield optimum grinding, metallurgical and profitability performance, not maximum life. In other words, mill liner profiles and relining speed become key profitability contributors and not simply 'must do' maintenance functions and costs. This paper includes a short history of RME's Mill Relining System development (Appendix A). These are the enabling technologies which permit more frequent liner exchange without incurring additional downtime imposts. The body of this paper outlines RME's vision of a 'liner profile vs. profitability' commercial model, underpinned by the rigour of PAS 55-1:2008 Asset Management Part 1: Specification for the optimised management of physical assets. The technical elements can be developed either intuitively (based on plant experience) or by using a combination of new measurement and modelling technologies. These new measurement and modelling tools provide the opportunity to predict the optimum technical solution for the maximum commercial outcome. Much of this can be modelled off-line, in the virtual world, before asking senior management to commit to an expensive liner experiment. The potential benefits are compelling.

Sep 13, 2010

Provide optimum visibility of mining operations while maintaining protection and comfort for ma-chine operators. Approach Cabs and canopies with hydraulically powered variable-height control were developed for several machines and tested in underground mining operations. How It Works From his position in the cab, the operator can raise or lower the cab, selecting a height that offers either more visibility of the working place or greater clearance for tramming. The entire cab enclosure moves up and down on guide rollers that ride on a pair of rails, and is actuated by a hydraulic cylinder controlled from within the cab. Normal working heights, for each of the four different cabs developed, are with the cab bottom from 6 to 8 inches above the mine bottom. A typical range of elevation (excursion) afforded by this design is shown in Figure 1.

Jan 1, 1978

By Matthew N. Rubin

This report summarizes the work performed under USBM Contract No. H0155155. The purpose of this work was to obtain operational data on retrofit noise control treatments suitable for use in coal preparation plants. This data was obtained by evaluating the performance of four categories of noise control treatments which were installed in a commercial coal preparation plant. The four categories of treatments were resilient screen decks, resilient impact pads, chute liners, and curtains. The selection, installation and initial evaluation of the treatments was documented in the Volume I report issued in 1977. This Volume II report summarizes the results of the long-term evaluation of the original treatments, as well as some additional tests which were conducted on elastomer-clad (resilient) screen decks. This project demonstrated the feasibility of a number of retrofit noise control treatments, some of which also proved to be quite durable over the long term.

Jan 1, 1982

By S. Vujic

The exploitation of stone (trachyte) at the ?Srebro? open pit mine, located on the northern slopes of the Fru?ka Gora National Park (Serbia) central area begun in 1964. Stone exploitation in this locality does not endanger the environment in an ecological sense, does not pose a threat to plants and animals, and apart from the terrain configuration changes, it did not leave behind permanent consequences to the environment. Projects for permanent cessation of mining operations and for land reclamation and spatial arrangement were completed in these circumstances. The paper gives a short review of the condition at the open pit mine; furthermore, the key problems and basic demands are presented, together with a concept of technical and biological land reclamation and the spatial arrangement of the mining complex. Keywords Open pit mine, land reclamation, spatial planning, spatial arrangement, National Park, Fru?ka Gora, Srebro.

Jan 1, 2011

By M. E. Hawkins

This Bureau of Mines report provides information on all of the 329 proved salt domes in the Gulf Coastal States and offshore area of the United States. It includes specific data related to location, depth to the cap rock and to the salt, storage facilities for LPG, and production of salt, sulfur, petroleum, and rock related to or associated with the dome structure in the subject area. Also included is a brief history of the salt, sulfur, and petroleum industries as related to the salt domes. Gulf Coast salt domes were the scene of the first discovery of a large deposit of rock salt in North America, the birthplace of the Frasch sulfur industry, and the location of the first large oil gushers that ushered in the modern liquid fuel age.

Jan 1, 1966

By Tapiwanashe Chenje, David Hewitt, Peter Radziszewski

"Steel media wear is a major cost component in mineral processing. In the case of existing operating mill, steel media wear prediction can be used to help compare the performance of steel media from different suppliers before completing marked ball tests. It can also be used to investigate how ores from different site of a given mine affect steel media wear. In the case of Greenfield cases, steel media wear prediction can be used to estimate the cost of steel media for a given feasibility study.This paper presents a wear testing and prediction methodology that ties together abrasion wear and corrosion wear testing results through the use of a simplified discrete element charge motion model. The experimentation dimension to this methodology takes samples for steel media, mine site ore and water to determine abrasive and corrosive wear parameters of a given media, ore, water set.The test methodology development is illustrated along with a comparison of wear predictions with observed wear rates in some operating mills. A case study is included that illustrates how this methodology was used to estimate steel media wear performance. The paper closes with a discussion on the use of parts of the experimental methodology to investigate other abrasive wear conditions such as liner wear, paste backfill piping and ore breakage as well as avenues for future test development.INTRODUCTIONThe cost of comminution processes represents a significant part of the overall costs of a mining operation. Grinding media/liner wear alone accounts for 15-25% of the total operating cost. The annual steel grinding media consumption is approximately 2.5 mtpa or 0.3% of total world steel production [Smorgon Steel Group, 2005]. Using an estimated grinding media cost of about US$0.75/kg [Halbe and Smolik, 2002], gives a media cost of over US$1.875 billion per annum. Mining continues to shift towards exploitation of lower grade ores as the higher grades get depleted. These low-grade ores require finer grinding for the liberation of the value minerals, and hence it can be assumed that grinding media consumption will also continue to rise.The Bond abrasion test, dating back to 1963, [Weiss, 1985] is still used to estimate the total mill media wear. This is a purely empirical test based on the ore. From Bond abrasion index tests, it is possible to determine a wear rate using the following function:"

Jan 1, 2009

By M. E. Hawkins

This Bureau of Mines report provides information on all of the 329 proved salt domes in the Gulf Coastal States and offshore area of the United States. It includes specific data related to location, depth to the cap rock and to the salt, storage facilities for LPG, and production of salt, sulfur, petroleum, and rock related to or associated with the dome structure in the subject area. Also included is a brief history of the salt, sulfur, and petroleum industries as related to the salt domes. Gulf Coast salt domes were the scene of the first discovery of a large deposit of rock salt in North America, the birthplace of the Frasch sulfur industry, and the location of the first large oil gushers that ushered in the modern liquid fuel age.

Jan 1, 1966