Search Documents

By J. F. Brand, J. C. van Dyk, F. B. Waanders

"Syngas from Africary’s Theunissen underground coal gasification (UCG) project will be used for power production and synthesis of liquid fuels and commodity chemicals. However, some of the coal components, especially condensable water, oils, tars, inorganic trace elements, and a small fraction of fly ash and particulate matter, make their way to the surface via the production well and can cause adverse impacts on downstream processes. Africary’s standard design incorporates a cold gas clean-up system that relies on relatively mature techniques based on highly effective wet scrubbers and acid gas removal (AGR) systems such as Rectisol®, but with the downside of low energy efficiency and waste water generation. In this paper, novel technologies for removing contaminants and species separation from the hot (T > 300°C) raw syngas are compared. Comparisons are made between supersonic gas separation (SGS), Ranque–Hilsch vortex tube (RHVT), vortex gradient separation (VGS), and inertia vacuum filtering (IVF), and a vortex-based gas separation concept is proposed for UCG applications. IntroductionImpurities in gasification feedstock (coal, biomass, waste, etc.), especially sulphur, nitrogen, chlorine, and inorganic mineral matter, often end up in the syngas and can cause adverse impacts on downstream processes. Africary’s standard design incorporates a cold gas clean-up system that relies on relatively mature techniques based on highly effective wet scrubbers and acid gas removal (AGR) systems such as RectisolR, SelexolR or aMDEAR; but with the downside of low energy efficiency and waste water generation.Hot (T > 300°C) gas clean-up technologies are attractive because they avoid cooling and reheating of the syngas stream. Some available warm gas cleaning technologies include traditional particulate removal devices such as cyclones, candle filters, membranes, and molecular sieves. The warm gas desulphurization process technology developed by RTI LLC (2018) requires hot syngas to remove sulphur and has become commercially ready. Many other hot gas cleanup systems are still under development, given the technical difficulties caused by extreme environmental and operating conditions."

Jan 1, 2018

By Frederick W. Slack

This paper will discuss the inherent value engineering associated with the design and construction of approximately 184,000 SF of anchored tieback wall, installed as part of the widening and drainage improvements for KY9 in Campbell County, Kentucky. The total project is 2.2 miles in length. The anchored walls, excavation grading and drainage total to a complete project cost of $28.4 million. This is one of the largest design-build projects undertaken by the Commonwealth of Kentucky. It also features another first for the Transportation Cabinet - the general contractor is responsible for quality control/quality assurance. The project is located just south of Cincinnati, OH and is situated along the east bank of the Licking River. The slopes along this stretch of the river have had a long history of movement and instability. The Kentucky Transportation Cabinet advertised the anchored wall portion of this project to be designed and constructed by pre-approved specialty contractors. The Transportation Cabinet provided the basic design parameters to each specialty contractor. Aspects to be discussed include the site and project history, previous attempts at slope stabilization along existing KY9, the technical proposal and bidding process, and the actual design and construction.

Jan 1, 2003

By J. Kretschmann

?We have constructed a world in which the potential for high-tech catastrophe is embedded in the fabric of day-to-day life.? (Malcolm Gladwell) The mining industry is a crucial provider for virtually every person?s needs and thus indispensable. Yet, mining is a complex and risky business: plenty of high risk factors can occur and severely affect nature and the miner?s life and health. Especially for small and medium enterprises (SME) risks may also threaten the economic existence of the company. The responsible and sustainable management of a company should thus be based upon the systematic finding and handling of risks or briefly upon an efficient risk management system. Why do we need risk management? Because nobody is perfect and we make mistakes in the normal course of operation.

Jan 1, 2011

AUSTRALIA CHAPMAN Gary JOHN WAGSTAFF CONTSRUCTIONS PTY. LTD. 1 Ashgrove Crescent 4060 ASHGROVE BRISBANE HILLAR Jaaes Director J.A. HILLAR & ASSOCIATES 99 Woolwich Road WOOLWICH, NSW 2110 WAGSTAFF John Managing Director JOHN WAGSTAFF CONSTRUCTIONS PTY. LTD. 1 Ashgrove Crescent 4060 ASHGROVE, BRISBANE AUSTRIA FUCHSBERGER M. TECHNISCHE UNIVERSITAT INSTITUT FUR BODENMECHANIK Rechbauerstrasse 12 8010 GRAZ

Jan 1, 1994

By P. Somasundaran, D. R. Nagaraj, Tarun Bhambani, P. Patra

Flotation separation and recovery of value minerals from ores containing fibrous silicate minerals are known to be quite challenging. Earlier studies have established that the metallurgical challenges (poor selectivity and recovery, high energy consumption, etc.) arise from the impact of the fibrous minerals (with high aspect ratio) on pulp rheology, which was found be rather complex. The complex rheological behavior of ore suspensions containing particles with high aspect ratio and its influence on flotation outcome are investigated in this study. Flotation tests and rheological measurements were carried out with both ores (containing fibrous minerals) and a model system comprising nylon fibers (chemically inert) added to a copper ore that had no fibrous mineral. These studies allowed the determination of contributions of physical properties of the fiber to pulp rheological behavior. Optical microscopy images of the fiber pulp indicated that the fibers entangled to form two levels of microstructures: two-dimensional (2D) aggregates under semi-dilute (< 20% solids) conditions and three-dimensional (3D) microstructures at concentrations > 30% solids. The yield stress (σ) values determined for the fiber pulp were logarithmically related to the volume fraction of the 2D/3D structures. The relationships developed here for different ARs showed that the yield stress of a flotation pulp changes with respect to shape, size, and the concentrations of the microstructures. Implications to the effects of such entangle networks on selectivity of flotation separation are discussed.

Copper, zinc, lead, and silver in the discordant magmatic-hydrothermal orebody of the Conrad Mine, N.S.W., all have a relatively high mean abundance. Any single concordant sulphide orebody containing the same metals has a similar order of mean abundance of only one or two of these, particularly copper, copper and zinc, or zinc and lead.The relative abundances of the metals in the Conrad orebody vary more widely than in concordant orebodies, and the lead-zinc-silver and copper-zinc-lead relationships are significantly different.INTRODUCTIONIn previous investigations of metal abundances in sulphide ores, the basis of selection of the orebodies was their form, and to some extent their geological setting, rather than hypotheses concerning their origin. In all cases they were generally concordant with the bedding of the sedimentary or meta-sedimentary rocks enclosing them, and most occurred in volcanic-sedimentary sequences. Their mineralogies were simple, and they were copper, copper-zinc, zinc or lead-zinc rich in composition. Most were of the type ascribed by several authors to exhalative-sedimentary processes.In one of these investigations (Stanton, 1958), it was pointed out that since the metals in ores of this type showed similar abundance patterns and behaviour, it would clearly be of interest to examine, and to compare with them, orthomagmatic and vein types, unquestionably derived from their igneous rock associates.The present investigation is concerned with a single orebody, of clearly discordant type, and of indisputable hydrothermal origin. The abundance and behaviour of copper, zinc, lead, and silver have been determined and compared to similar data fOl!&apos; the concordant type. Such a comparison tests the possibility that metal abundance patterns of base metal ores may be indicative of the mode of ore deposition.

Jan 1, 1963

By S. J. Thomas, P. A. Lilly, J. A. L. Napier

An industry research project has been established to examine the issue of rock mass failure in large open pit slopes. The approach began with numerically modelling failure at the laboratory scale with a displacement discontinuity program. The interim results from the program suggest the output failure mode is dependent upon the input parameter cohesion weakening. Es wurde ein Forschungsproject mit unterstützung von Bergbauindustrie bearbeitet. Die Zielsetzung der vorliegenden Arbeit war die Analysierung des Böschungsgefähr im größen Festgesteinstagebauen. Das Verfahren besteht aus der numerischer Modelierung mit Ansatz einen sonderen Rechnerprogram. Die erste Ergebnis zeigt, daß die Aufgabe am Angabendaten (cohesion) abhängig sein wird. Un project de recherche industriel fût conduit avec le but d’examiner les éboulements de roche dans les mines a ciel ouvert. La premiere étape a été de modelliser numériquement les éboulements dans un laboratoire en utilisant un programme de déplacement discontinu. Les resultants préliminaires du programme indiquent que la prédiction des ébouliements est directement reliée à la magnitude de la cohesion.

Jan 1, 2003

By L. A. Haas

The Bureau of Mines conducted bench-scale leaching tests with recycled spent copper electrolytes and copper-nickel mattes produced from the Minnesota Duluth Complex concentrates. This report describes the first stage of an overall two-stage leach operation. The objective of this research was to determine the matte-leach technology required to convert spent copper electrolyte into an enriched nickel liquor suitable for a nickel refinery and there-fore essentially free of copper, iron, and sulfuric acid. The experimental variables investigated were matte composition, particle size, spent electrolyte content, pulp concentration, oxygenation, temperature, and time. The time required to produce an enriched purified nickel liquor decreased with increasing pulp concentration, temperature, and oxygenation, but increased with increasing particle size and electrolyte copper and acid content. Nickel-rich (about 50 g/l) liquors at a pH of about 4 and containing less than 1 g/l of copper and iron were produced at 70° C by leaching minus 325-mesh low-iron (less than 5 pct) matte for 8 hours with spent electrolyte containing 22.4 g/l Cu, 28.9 g/l Ni, less than 0.1 g/l Fe, and 50 g/l H2S04 at a pulp concentration of 1 kg of matte per liter of spent electrolyteo Varying the nickel content of the spent electrolyte from 11 to 101 g/l appeared to have no appreciable influence on the matte leaching characteristics.

Jan 1, 1981

By K. Coleman, C. Visser, N. Selby, X. W. Pan, T. Letwaba

A prototype weightometer soft sensor is under development at DebTech, De Beers in partnership with Venetia Mine. Its main function consists of an online data source; data validation; dynamic weightometer models; online detection of weightometer failure; alarming and replacing a weightometer when it fails. 31 dynamic models have been developed. All models with R2>= 85%are accepted as good models and they generally have satisfactory results with a daily error of less than 8% within 90% confidence level. By using those models, a set of soft sensors can be set up to cover all weightometers in the entire processes starting from primary crushing to the stock piles of dense medium separation (DMS). Some practical issues and concerns on model development are discussed, including data collection, data analysis, data pre-processing, variable selection, time delay, model training and model validation. When deploying the weightometer soft sensor system, the potential benefits could include: reduction in plant downtime; reduction in unplanned maintenance and even replacement of non-critical weightometers, particularly where nuclear weightometers are used. Keywords: soft sensor, weightometer, dynamic modelling, neural network modelling

Jan 1, 2003

By Clayr Alexander

Stillwater Mining Co. (SMC) is engaged in developing, extracting, processing and refining palladium, platinum and associated metals (PGM)from the J-M Reef. This geological formation is located in Stillwater, Sweet Grass and Park counties in southern Montana. Associated byproduct metals include rhodium, gold, silver, nickel and copper. SMC’s current mining operations are near Nye, MT. The company is currently developing a second underground palladium and platinum mine, the East Boulder project, about 21 km (13 miles) west of the Nye operations. A 5,650-m (18,550-ft) tunnel is required to gain access to the ore-bearing horizon (J-M Reef).

Jan 1, 1999

By John Watson

New Technologies, New Challenges and New Opportunities For quite some time now, numerous explosive manufacturers have spent untold man-hours and millions of dollars trying to develop a blast initiation technology that would “once and for all” provide users with what was once believed to be only a theoretical possibility...nominal timing. Zero “cap scatter” (the amount of variation of delay timing from the targeted nominal) has been the industry’s goal ever since delays were first introduced into the marketplace. Just as adding delay time between blast-holes improved blast performance since their introduction, having the wrong delay or a poorly timed blast has proven to be very inefficient and in many cases hazardous. The question of how precise a blast initiation system needs to be still remains unanswered, but electronic detonator systems being used today indicate that significant improvements can be achieved over conventional pyrotechnic detonators. These systems can typically provide single digit millisecond ranges of variability, if not sub-millisecond in some cases.

Jan 1, 2003

By A. N. Veltmeyer

"INTRODUCTIONTeck-Corona Operating Corporation's David Bell Mine is located 35 Km east of Marathon, Ontario. In conjunction with its 1000 tonne per day gold concentrator, the company operates an effluent treatment plant for the treatment of mill, mine and site effluents prior to environmental discharge. This paper provides a brief overview of treatment strategies and methods, employed to detoxify final effluent.WATER MANAGEMENTThe tailings impoundment basin, located 3 Km south of the plant site, provides storage capacity for all process effluents and site run-off. Basin supernatant (reclaim water) is recirculated to the plant for reuse as process water, in order to minimize fresh water consumption. As site run-off and limited fresh water intake exceed natural losses due to evaporation, reclaim water in excess of process requirements is passed through the effluent treatment (ET) facility to control tailings basin level by providing regulated discharge of environmentally acceptable effluent. (Figure 1)PASSIVE TREATMENTTo reduce treatment costs and burden on the ET facility, reclaim water is fed to the plant to take maximum advantage of natural destruction processes occurring in the tailings basin.These include: volatilizationphotodecompositionbiological oxidation and precipitationstorm water dilutionConcentrator recovery techniques (Figure 2) are directed toward maximizing gold recovery while limiting the addition and extraction of contaminants requiring disposal and eventual treatment.Currently ore ground to 90% -200 mesh is pre-aerated at pH 9.0 with lime for 18 hours prior to 30 hours cyanidation at pH 9.5 with low cyanide ion excess (70 ppm).Pre-aeration passivates cyanicides prior to cyanide contact. This reduces cyanide consumption and the formation of cyanide complexes. In conjunction with recovery requirements low pH is maintained to retard the dissolution of stibnite into its antimony and sulfide components."

Jan 1, 1989

By Carsten Rühlemann, David Friedmann, Bernd Friedrich, Thomas Kuhn

"This paper explores the option of direct reduction smelting of the nodules from the German license area in the equatorial NE Pacific in a submerged arc furnace (SAF). An optimized slag design is proposed to separate the larger Mn-bearing stream from the valuable metals (i.e. Ni, Cu, Co, Mo). The slag optimization allows a maximum of Mn to be retained in the manganese-silicate slag on the one hand and a maximized metal recovery in a FeNiCuCo alloy on the other. This way, the goal is to make use of the complete nodules (“zero-waste”) instead of extracting only the metals Ni, Cu, and Co, which make up about 3 wt%. The process closely relates to the “Inco Process” by the Ocean Management Inc. (OMI) of the late 1970s, which was a consortium of INCO (International Nickel Company, CAN; today Vale Canada), Preussag AG & Metallgesellschaft AG (GER), DOMCO (JPN), and Sedco (USA). However, the manganese containing slag is investigated in more detail to recover FeMn, FeMnSi and/or SiMn. To optimize the process modern tools such as thermo-chemical modeling in FactSage™ have been used. [1,2]Polymetallic deep-sea manganese nodules may offer a decreased dependency of raw material imports for Germany and the EU. Currently, four European countries (United Kingdom, Belgium, Germany, and France and an Eastern European consortium (InterOcean Metal)) hold exploration licences for these nodules in international waters in the equatorial NE-Pacific. The license areas each cover 75 000 km2 of the seafloor and are located in the Clarion Clipperton Fracture Zone (CCZ) south east off Hawaii at water-depths between 4000 and 6000 m. The nodules may be used as a resource for industrially important metals such as Cu, Ni, Mn as well as for technology metals like Co, Mo, V and Zn. The average chemical composition of nodules from the German license area is presented in Table 1. [3,4]"

Jan 1, 2017

Judicious placement of a range of geotechnical instruments was employed at the Tasmania gold mine, Beaconsfield, Tasmania, as a key strategy in the monitoring of rock mass conditions over the past four years. The range of instruments employed included vibrating wire stress-meters and hollow inclusion cells to monitor changing stress conditions, resistance wire and multipoint borehole extensometers to monitor the impact of stress changes on the integrity of the rock mass, and instrumented cable bolts and threadbar bolts to monitor the static and dynamic impact of rock mass changes on the installed ground control system. Initially the monitoring was of a qualitative nature, monitoring change from the time of installation. The value of the output was considerable when considered in relation to the ongoing seismic record which was also being monitored. It was clear from the seismic record and the monitoring results that stope blasting was the primary trigger for changing rock mass conditions. However, it was unclear how well observed behaviour was reflecting conditions anticipated by elastic numerical modelling. The latter had predicted significant stress increase in the near field of man-access footwall development. Qualitative monitoring and visual inspection did not support the modelling prediction, and this led to a program of quantitative measurement being undertaken. Measurement of the absolute stress condition in the backs of footwall development immediately adjacent to monitoring hollow inclusion cells provided the benchmark for tracking quantitative stress change. The program provided insight into the evolution of principal stress field magnitude and orientation in relation to rock mass change observed with extensometers and instrumented ground control elements, as well as providing a degree of calibration between the elastic numerical modelling and the virgin stress field. Calibrated monitoring data has also provided a useful benchmark for finite element modelling which is to be used for future mine-wide design.

Nov 25, 2010

By William A. Gibson, Kenneth P. Neumann

In 1967, development of the Cyprus Thompson Creek molybdenum deposit began near Challis, ID. The first mining claims were staked on an intrusive rock out-crop. Exploration continued for 14 years. In 1978, the decision was made to develop the deposit. In Dec. 1980, approval was received for the environmental impact statement and facilities construction and waste rock removal began. By the middle of 1983, 126 Mt (139 million st) of rock had been removed and all facilities completed. Location The Thompson Creek project is located about 58 km (36 miles) southwest of Challis in Custer County, in south central Idaho. The mine and mill are situated between 2.2 and 2.6 km (7,217 and 8,530 ft) in elevation. The project is located in an isolated area. Surrounded by mountains, it is adjacent to the Sawtooth National Recreation Area. The Salmon river is 8 km (5 miles) south of the project. The project claim block is lo-

Jan 1, 1984

By E. R. Maize

[?he scconG rcport of :his st?rI.org 8cdt with o3servatioi:s of conver- gence of roof an4 floor at t!x*re: ?.cc.-.tioris iri til~ ClVucible mine of kke Cru- cib1.o Fuel Co. Data on sl:&apos;ociacnce ?.rd Lztcrcl mwe:~cnt cf the surface were .:lven for two of these areas, cnS it was mentioned that ~lr~~ilar data were being obtained on a ?art of Pe:sc:rlvtzr.ia Fii~l?trr.y FE:, ~i!lic;l pcser: over the third area. &apos;I&apos;hie hichwc :LEO FasseE over t!lc ITenncoli::. :.line of the Bnckeye Coal Co. 9 milcs to &apos;;he so-lth, cnd at P. l~tcr C&apos;..att: ~.nr?r.,cc?r:cntS *.rere mnd.e to make similar observati on3 there. This y: pr mrnmri:.c n Czto obtnino? at those two locetionn,]

Jan 1, 1941

By J. A. Bakken, M. T. Jonsson, G. A. Saevarsdottir, H. Palsson

The electrodes of a Submerged Arc Furnaces carry a high current and are subject to enormous stresses caused by both the electric arc itself, and the current distribution within the electrode. The external effect of the arc on the electrode is treated in a different paper at this conference, The purpose of this paper is to analyze the thermal effects of ohmic heating within the electrode at the arc attachment on the carbon based electrode, using data for Søderberg electrodes. The thermal conditions are then used to examine stress conditions in the vicinity of an arc. Two types of models of an electrode are presented in the paper. The first type is an accurate finite element model, based on both two and three dimensional elements and the second type is an one dimensional model, providing better insight into the problem. For the second type, a spherical model of thermal conditions in a semi-infinite solid has been developed. Results show that the electrode surface is heated quickly up to a maximum temperature and for a specific test case, the surface can only withstand the load for about 10 seconds. Also, the thermal stresses on the surface are very high which will increase erosion on the surface in addition to normal evaporation.

Jan 1, 2007

By Donald W. Gentry

Introduction The mining industry is perhaps best characterized by the numerous and abnormally high risks associated with the business of mining and by its most basic assets - ore deposits, people and technology. At the most fundamental level, it is the quality and effective utilization of these basic assets that determine a mining company&apos;s ability to compete efficiently in the international market place. The gold industry has received much attention in recent years and especially in recent months, for good reason. This commodity serves as an excellent platform for the subsequent discussion of these three basic assets and their role in mining&apos;s future. Facets of the gold industry The fate of this noble metal in recent times illustrates some of the various risks associated with the mining industry and the importance of high-quality assets, whether they be ore deposits, people or technologies. The following comments pertaining to the gold industry help place proper focus on subsequent discussions. All monetary amounts given are in US dollars. Throughout 1997, falling gold prices broke record after record: first hitting three-year lows, then a 12-year low in July and finally an 18-year low at year&apos;s end. From Jan. 1 through Dec. 31, 1997, the price of gold fell by more than $2.57/g ($80/oz), or some 22%. The decline in gold-mining profitability and stock prices was even more dramatic. At the beginning of 1997, the 20 largest gold producers in North America had a market capitalization of approximately $44.5 billion. At year&apos;s end, this market cap had fallen to $26.2 billion, a reduction of 41%. The total market cap of all the world&apos;s gold companies fell from $71 billion to $46 billion, a 35% drop (Serwer, 1998). Analyses suggest that, at a spot gold price of $9.65/g ($300/oz), only one, or possibly two, North American gold-producing companies can make money when break-even or "total costs of production" are considered. While strong hedge positions mitigate this situation in the short term, clearly, this is an industry in desperate straits. For example, write-downs for North American producers in 1997 were approximately $2.5 billion. Speculative short positions in 1997 were near historical record highs and generally exceeded long positions by factors of 9:1 or 10:1. Much of this is driven by some US commercial banks, hedge fund managers and commodity speculators who can significantly move gold prices sharply over short periods of time by selling gold they do not own in the expectation they can buy it back at a lower price before they have to deliver. These signifcant short positions are likely to continue as long as central banks are willing to sell or loan gold to financial institutions that in turn make the gold available to speculators who hope to capitalize on price fluctuations. The Far East accounts for approximately 26% of the annual demand for gold. Including India, the region accounts for 43% of total demand. More than 85% of the physical demand for gold is for investment jewelry in Asia and the Middle East. This demand is extraordinarily price sensitive. The fairly recent turmoil in Asian markets and economies, combined with currency devaluations throughout the region, have made gold more expensive (30% to 50% in local currencies) for those peoples most likely to treat gold as a safe investment haven. Higher interest rates also have reduced the amount of money they have to spend on consumer goods such as jewelry. All of these recent Asian events are deflationary in nature. Deflation, if coincident with rising unemployment, could result in significant dishoarding of gold. There is one key fact to remember when analyzing

Jan 1, 1999

By Albert W. Deurbrouck

This Bureau of Mines report describes the washability characteristics of 13 coalbed samples collected in Colorado. Such data are needed to evaluate the quality of the coals of the West, where most of our low-sulfur-content coal reserves are found. Of the 13 samples included in this report, 11 had a total sulfur content of 1 percent or less. All of the samples contained low percentages of ash or could be readily washed to a desirable ash level with minimal loss of yield. The coals ranged in rank from high-volatile A bituminous to subbituminous B; nine of the samples were high-volatile C bituminous. The coalbeds ranged in thickness from 6 to 26 feet; the average was about 8 feet.

Jan 1, 1970

By S. Y. Tan

The thermal stability of fully silicided NiSi with arsenic doping on silicon was investigated. The aims of the work were to investigate the Ni silicide phase-related issues associated with arsenic dopant and thermal annealing on Ni-FUSI/HfO2/Si and Ni-FUSI/HfSiO/Si gate stacks. It was found that arsenic-incorporation demonstrated some improvement in both morphology and phase stability of nickel silicided films at high processing temperatures regardless underlying gate dielectrics. The correlations of Ni-Si phase transformation and arsenic doapnt with their electrical and physical changes were established by sheet resistance measurements, X-ray diffraction (XRD), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) analysis. Furthermore, the modulation of the work function (WF) of Ni fully silicided gates by arsenic impurity is presented, comparing the effects of dopant (As) on the WF and silicide phases (NiSi and NiSi2). It confirmed that the work function of NiSi can be tuned by implanting arsenic dopant, but it ineffective for NiSi2 phase.

Jan 1, 2010