Search Documents

By A. Lyndon

Vertical and lateral load tests were carried out on two 13 m deep bored cast-in-place instrumented piles, socketed into weathered sandstone. The first pile, 1200 mm in diameter, was loaded vertically to a maximum of 16000 kN and then loaded to failure under lateral load (1900 kN). The second pile, 1500 mm in diameter, was tested under lateral load up to a maximum of 2400 kN. It was found that the deflections of the 1200 mm pile were more than twice those of the 1500 mm pile under similar loads. The soils on the site are not easily tested in the laboratory, or by conventional insitu site investigation techniques, parameters needed in design can only be reliably obtained from pile test results. In this report shear moduli are back analysed from the vertical load test and the two lateral load tests. For these similarly installed piles very different design parameters were determined from the lateral load tests, the only known major difference between the piles being that the 1200 mm pile was loaded vertically before it was loaded laterally. Changes in G values needed to match performance under vertical load if applicable to lateral loading could have accounted for a significant amount of the difference.

Jan 1, 1989

By Thomas L. Starks

Surface soil/spoil Samples (0-10 cm) from experimental test sites in western North Dakota were aseptically collected during August 1975 and each month (May through September) during 1076 and 1977. Selected samples were Cultured in a defined inorganic medium and after six weeks the algae were identified. Chlorophyll u content of the soil/spoil was used as a measure of the algal abundance. Soil physical-chemical properties, species variety and abundance were statistically analyzed. All test sites revealed distinct soil algal communities and demonstrated a successional trend as evidenced by significant increase, in species variety and bionmass over time. Some soil factors, calcium, copper, and phosphorus affected species variety and abundance at more than one situ. Others were important at specific sites; silicon and aluminum at the South Beulah test site; manganese sodium and zinc at the North Beulah test site No. 1 and boron, cadmium and magnesium at the North Beulah test site No. 2. Topsoiled areas had higher species varieties and abundances when compared with control areas, as did plots treated with amendments such as leonardite and fertilizer Generally.

Jan 1, 1982

By R. L. Whiting, H. J. Ramey

The basic study from which this paper was prepared was started as the result of the growing need throughout the world for increasing quantities of energy in all forms. Quite obviously, natural forms of energy that are readily available at low development cost are those in greatest demand. The underdeveloped countries — and particularly those having little or no petroleum resources — are the countries in which the most interest is being shown in the newer energy sources. One of the least expensive energy sources is natural geothermal steam.'-* Although this form of energy has been recognized for centuries, it has been only during the past 20 years that serious efforts have been made to harness it. Natural geothermal steam energy in Italy, New Zealand, Mexico, Japan, and California is now being produced through wells to drive turbines and generate electricity. Further, active exploration for natural geothermal steam is being conducted in Hawaii, Fiji, Taiwan, Chile, Russia, Greece, and Katanga. It is surprising to find that most geothermal steam exploration is in the "steam seep" stage. That is, surface studies are made and exploratory wells are drilled in the general area of steam seeps. However, in the larger geothermal steam areas, there have been efforts to apply the most modern geological and reservoir engineering principles in order to define the reservoir parameters, particularly those relating to estimates of reserves and future productivity. This paper is concerned with the development of appropriate equations and techniques to facilitate these estimates. Production of natural steam or hot water presents problems different from those experienced in the production of oil and gas. For example, steam or hot water systems may be essentially single-component systems, while hydrocarbon systems are most frequently multicomponent fluid systems. Heat effects are much larger for water than for hydrocarbon systems; and the natural steam production may or may not be isothermal, while production of petroleum reservoirs is considered normally to be isothermal. Petroleum reservoir engineering principles may be applied to natural steam or hot water reservoirs if the inherent differences in the systems are considered. The basic considerations involved in geothermal steam reservoir engineering are: thermodynamics, physical and thermal properties of water, materials and energy balances, fluid influx, and performance matching and predicting. Thermodynamics Fig. 1 is a pressure-temperature diagram for the liquid-vapor region for pure water, showing the critical point and five other points representing possible initial conditions for a geothermal steam reservoir. To generate a physical appreciation for the mechanics of natural steam production, it is helpful to consider

Jan 1, 1970

By J. Werfling, J. R. Kiehl

SUMMARY: The effects of blasting on structures are assessed on the basis of the maximum amplitudes of the occuring vibration velocities. If the standard values in the German Standard DIN 4150 are not exceeded, damages to structures are not to be expected. The estimation of the maximum vibration amplitudes is usually based on experience or on emperical formulae. However, a comparison of expected with measured values shows that these estimations are not conservative, particulary in case of small distances between blasting locations and structures. More reliable predictions are possible on the basis of numerical analyses, which simulate the three-dimensional propagation of waves with consideration of the geomechanical and geometrical conditions. In addition to the expected velocities, these analyses also allow the determination of stresses resulting from dynamic loading. If the dynamic stresses are known, the effects of blasting on structures can be predicted. ZUSAMMENFASSUNG: Die Auswirkungen sprengbedingter Erschütterungen auf bauliche Anlagen werden in der Praxis auf der Grundlage der Maximalamplituden der auftretenden Schwinggeschwindigkeiten beurteilt. In der DIN 4150 werden Anhaltswerte angegeben, bei deren Einhaltung Schäden von Gebäuden nicht zu erwarten sind. Die Abschätzung dieser Schwing-geschwindigkeiten erfolgt meist auf der Grundlage von Erfahrungswerten oder empirischer Formeln. Der Vergleich der prognostizierten Werte mit Meßergebnissen zeigt jedoch, daß diese Ansätze insbesondere dann, wenn die Abstände zwischen den Sprengorten und den Gebäuden gering sind, nicht konservativ sind. Zuverlässigere Prognosen sind auf der Grundlage von numerischen Berechnungen möglich, in denen die räumliche Ausbreitung von Erschütterungen unter Berücksichtigung der geomechanischen und geometrischen Verhältnisse simuliert wird. Mit derartigen Berechnungen können die zu erwartenden Schwinggeschwindigkeiten und die aus der dynamischen Beanspruchung resultierenden Spannungen ermittelt werden. Dies ermöglicht Aussagen über die Auswirkungen sprengbedingter Erschütterungen auf Bauwerke. RÉSUMÉ: Les conséquences de vibrations résultantes d'explosions pour des bâtiments sont estimés dans la pratique à partir des amplitudes maximales des vitesses d'oscillation. Dans la norme allemande DIN 4150 des valeurs d'orientation sont données, avec l'observation desquelles de dommage à des bâtiments n'est pas à présumer. Ces vitesses d'oscillation sont estimés généralement à partir de valeurs d'expérience ou de formules empiriques. La comparaison des valeurs prédits avec des résultats de mesures montre cependant que ces hypothèses ne sont pas conservateurs, en particulier si les distances entre les lieux de sautage et les bâtiments sont petites. Des prédictions plus fiables sont possibles à partir de calculs numériques, dans lesquelles la dissipation spatiale de vibrations est simulée en considération de la situation géoméchanique et géométrique. Avec tels calculs les vitesses de vibration à présumer et les contraintes résultantes de l'effort dynamique peuvent être établies. Cela permet de constater sur les conséquences de vibrations résultantes d'explosions pour des bâtiments.

Jan 1, 2003

By Charles W. Briggs

The steel foundries of Germany were investigated for the purpose of ascertaining (1) the type and classification of steel structures produced as castings, (2) processing methods, (3) the mechanical properties of carbon and alloy cast steels, (4) the type and character of defective castings, (5) the appearance of castings, (6) research in steel castings, and (7) plant lay-out and equipment.

Jan 1, 1946

By D Goel

India, the second-largest steel manufacturer globally, achieved crude steel production of around 126 million tonnes (Mt) in the last financial year of April 2022 to March 2023 (FY23), against an installed capacity of 162 Mt. In its National Steel Policy, 2017, India has undertaken targets to take the crude steel production capacity to 300 Mt by 2030–2031 and production and demand to around 255 Mtpa, also by this deadline. The blast furnace-basic oxygen furnace (BF-BoF):electric arc furnace-induction furnace (EAF-IF) ratio in 2022 was at 44:56.

Sep 18, 2023

By W. R. K. Wu

Results of linear correlations of two to four variables by the least-squares method are presented. The variables include 63 parameters representing coal composition, coal plasticity, and coke strength. The composition parameters are on chemical analyses; the plasticity parameters, on three plastometer and dilatometer tests and four miscellaneous tests; and the coke-strength parameters, on three ASTM indices. Seventy-two to eighty-four plastic coals were used in the plasticity and carbonization tests, which together form the basis of this report; 43 nonplastic or weakly plastic coals were used in the coal-band studies. Plots of relations between volatile matter, carbon, and oxygen contents of 1,860 U.S. coals and the 84 coals used are shown. Similar plots between volatile matter and hydrogen or atomic H/C of the 84 coals are also included. Significances of regression coefficient signs for coal composition parameters in the significant correlations found are discussed. Based on these significances, the following relations are shown: (a) coke strength versus average aromaticity, or mineral matter content, of the parent coal; (b) characteristic temperatures of the plastometer and dilatometers, the free-swelling index, or the Gray-King type versus average hydroaromaticity of the coal; and (c) nontemperature parameters of the plastometer and dilatometers versus the physical properties of a certain group of compounds from thermal decomposition of coal. Similarly, significances between the positions of coals in the coal band and the aforementioned relations are also discussed. A structural theory of coal plasticity is proposed. Applications of the correlation results are discussed. Composition parameters, such as carbon, atomic H/C, and calorific value may be used as a basis for selecting coking coals for stronger coke. Plasticity parameters, such as the end temperatures of the plastometer and dilatometers and the free-swelling index, may be used for the same purpose. Based on the best correlations found, coke-strength indices may be estimated to within 4 to 8 units of the observed values; the end temperatures of the plastometer and dilatometer tests, 5° to 10° C.; and the free-swelling index, within 1 unit. Accuracies of all these estimated values are examined, based on the experimental errors of the data involved. Finally, estimations of plasticity parameters from one test with those from others are shown.

Jan 1, 1971

By Tom Goodell, James Cox, Scott Scovira

Resolution Copper Mining is sinking a 6943 foot (2116 m) deep shaft to access and develop a new panel caving mine with approximately 1.6 billion known tons of porphyry copper resource. This mine will take several years to ramp up to its full production level of 132,300 tons per day (120,000 tonnes per day) and is scheduled to begin production in the early 2020s. Resolution's shaft sinking contractor Cementation USA is using state of the art sinking methods combined with a largely local labor force to complete this record breaking shaft. Resolution's No. 10 Shaft has finished diameter of 28 feet (8.5m) and as of October 2013 is at the 6625 foot (2020 m) level. Upon completion in early 2014, the No. 10 Shaft will be the deepest single lift shaft in the United States.

Jan 1, 2014

By Wittenberg J. C, Reid A. F

A method is described for the rapid and effective production of polished section mounts of ore and mineral particulates to the standards required for automated image analysis. This requires mounting without segregation of particles by mass or density, and it is also preferable to avoid having particles in contact so that they can be recognised as individuals. To achieve this, the particle samples are first split to an appropriate degree in a rotary riffle, and the sub-sample mechanically diluted and thoroughly mixed with an inert filler of the same size range as the particles. Just sufficient epoxy resin is added to make the mixture fluid. During setting, the ore particles are mechanically supported by the inert filler particles, thus maintaining the particles in a random three-dimensional distribution. A rapid two-stage grinding process, based on the successive use of 600 mesh silicon carbide and 1200 mesh (10 um) corundum on cast iron plates, is followed by three stages of mechanical diamond polishing on cloth laps. Hand polishing is entirely avoided, as is the use of papers.

Jan 1, 1984

By A. R. T. Denues

"INTRODUCTION The orienting phases of the current investigation of cushioned blasting in the Explosives Division of the Bureau of Mines were indicated in a previous publication (5) 3/. Pertinent literature reviewed therein indicated a highly controversial field. This emphasized the need for experimental studies of many factors that affect the health and safety of miners and the efficiency of mining operations. Results of some orienting tests showed marked effects on practical hazards. Further, they emphasized the necessity and importance of the contemplated investigation. The scope and general plan of these practical inquiries into the safety of cushioned blasting were indicated.This investigation of cushioned blasting relates to the various means employed to reduce the intensity of application of energy from explosive actions in boreholes. It has been suggested (from p. 19 of reference 5) that the divisions of this work would correspond to the salient hazards affected by cushioned blasting. These include the ignition hazard, hazards from poisonous gases, and other practical hazards in the blasting technique. The ignition hazard was resolved into two components of approximately equal weight. These include studies of effects upon (1) the incendivity of blown-out shots and upon (2) the occurrence of such shots. Experimental studies of effects on the incendivity of blown-out shots were first undertaken. Questions of the best procedure for making these evaluations have been adduced, and the interpretation and utilization of the results of gallery testing seemed to require detailed attention; some preliminary general considerations of such testing were therefore necessary."

Jan 1, 1943

By E. D. Calvert

The Bureau of Mines, in its effort to promote greater utilization of domestically abundant materials, conducted reasearch on an alternate mold material that has commercial potential for titanium investment casting. Using variations of the conventional lost wax molding process, investment shell molds were formed entirely of fused, calcia-stabilized Zr02 and a Zr02-forming binder. Optimization of binder/slurry properties', stucco grain size and dis¬tribution, and curing practices resulted in a structurally sound investment shell that was distortion free and thermally stable. Small titanium castings, weighing up to 10 pounds, were prepared in unheated molds by both static and centrifugal casting techniques. Microstruc¬tural examination of the castings revealed that mold fill and surface quality were enhanced by centrifugal casting, although good results also were obtained from the statically poured molds. Microstructural and electron microprobe examinations showed that excessive, brittle case formation could be avoided by curing the dried shell molds in air for at least 2 hours at 1,400° C. Increasing curing temperature and time above these levels yielded added bene¬fits. Molds fired in vacuum at 1,500° C for 4 hours yielded castings essen¬tially free of case formation. The tensile properties of as-cast test specimens (no surface conditioning performed) id the chemical composition of representative metal samples showed that castings produced were comparable to Grades C-1 and C-2 unalloyed titanium This indicated that no sifnificant degradation of metal properties resulted from mold/metal interaction.

Jan 1, 1981

Using Positron Emission Particle Tracking (PEPT) to Investigate Industrial Systems

Sep 13, 2010

By T. E. Bernard

Occupying a refuge alternative (RA) is an accepted practice in mine fires and explosions when escape is not feasible. MSHA has promulgated a final rule on refuge alternatives that includes a recognition that thermal environment is an important consideration. To this end, an environmental index was specified. The question remains about how to test a refuge shelter to demonstrate that it meets the final rule. The analysis followed five activities: A. Provide an estimate of heat generated by an individual refuge alternative occupant; B. Evaluate the Steadman Apparent Temperature criterion of 95°F; C. Discuss simulations based on body temperature or skin temperature limits; D. Suggest method of simulating human heat generation during refuge occupancy; and E. Suggest alternative methodologies/criteria for evaluating heat and humidity survivability inside a refuge alternative.

Feb 27, 2013

By F. B. Samani, B. Stabel

The 1,000 MW Hydro Power Station Masjed-e-Soleiman (formerly called Godar-e-Landar) in Iran is under construction since 1992. The rock engineering aspects of the major underground structure, i.e. the powerhouse cavern shall be reported on in detail. The geotechnical investigations are described and results given. The results of several geotechnical analyses are presented. The designed and executed rock support is given. A description of the monitoring systems and typical measurement results obtained during and after excavation are presented. The lessons learnt during construction of the Stage-I powerhouse cavern were applied on the extension of the powerhouse cavern, which is to house an additional 1000 MW. Details regarding the unexpected behaviour of the Mudstones are given. Die 1000 MW Wasserkraftanlage Masjed-e-Soleiman (vormals Godar-e-Landar genannt) befindet sich seit 1992 in Bau. Dieser Artikel berichtet im Detail über die felsbaulichen Aspekte der Untertagebauwerke, insb. der Maschinenkaverne. Die geotechnischen Untersuchungen werden beschrieben und deren Ergebnisse wie die Ergebnisse verschiedener Berechnungen werden präsentiert. Die geplante und die ausgeführte Felssicherung wird angegeben. Die eingebauten Überwachungseinrichtungen werden beschrieben und typische Ergebnisse während des Aushubs und danach werden dargestellt. Die Erfahrungen beim Aushub der Kaverne der Stufe I wurden beim Entwurf der Kaverne der Erweiterungsstufe II, die weitere 1000 MW beherbergen wird, berücksichtigt. Details zum unerwarteten Verhalten des Schluff-/Tonsteins werden angegeben. La centrale hydroélectrique de Masjed-e-Soleiman (dénommée anciennement Godar-e-Landar), d’une puissance de 1.000 MW, est en construction depuis 1992. Un rapport détaillé sera présenté sur les aspects relatifs à la construction en enrochements de l’aménagement souterrain principal, à savoir la caverne abritant la salle des machines. Une description des investigations géotechniques réalisées y est fournie ainsi que les résultats correspondants. En outre sont présentés les résultats de plusieurs analyses géotechniques. L’ancrage dans la roche tel que projeté et réalisé est présenté. Une description des systèmes de contrôle ainsi que les résultats de mesures typiques obtenus au cours des travaux d’excavation sont donnés. Les leçons tirées lors de la construction de la Phase 1 de la caverne de la salle des machines furent appliquées à l’extension de la caverne de la salle des machines, qui doit abriter une unité supplémentaire d’une puissance de 1.000 MW. Par ailleurs, des détails sont donnés sur le comportement inattendu des argilites.

Jan 1, 2003

Confirmation that acid drainage (AD) was a significant environmental issue for the Australian minerals industry came in 1992 with the first national workshop on the topic. Subsequently the extent of AD was documented in a national survey published in 1997. The recommendations arising out of that survey served as a platform for actions by government, industry and industry-support organisations such as the Australian Centre for Mining Environmental Research (ACMER) to enable more effective prevention and management of AD. This paper briefly documents the extent of AD in the industry, the government regulations and guidelines for AD management, industry initiatives, the role of ACMER and other organisations in assisting industry through research and technology transfer, and the efforts being made to deal with AD at derelict mines. Future management of AD in the industry will be assisted by the linkage of Australia (through ACMER) into the International Network for Acid Prevention (INAP) which is facilitating the interchange of knowledge on AD as well as coordinating global research on the topic.

Jan 1, 2003

The November General Meeting of the Branch was held in the St. Helena Club at 8.00 p.m. on the 17th November, 1970. Mr J. N. Saunders (Chairman) was in the chair. There were also present six fellows, N. A. Honnet, C. J. Isaac, J. G. Kirchner, (Committee Members), J. M. Meyer, S. L. S. Swart and J. W. Wilson; seven members, D. V. Baum, M. de Lange, A. H. Edwards, G. J. G. Emere, E. R. Penny, G. P. Rundle, C. G. J. Vermeulen; six graduates, N. Mayer, H. Miller, E. J. Shillaber, P. J. H. Short, M. H. Smith, T. R. Stromsoe; five associates, M. Andriesse, A. E. Hooper, A. Paschalides, R. L. Solms, W. M. Todd; one student, J. C. Simms and 14 visitors. Apologies for absence were received from Messrs L. O. W. Leimer and G. Y. Nisbet. MINUTES OF THE ANNUAL GENERALMEETING The Minutes of the Annual General Meeting held on the 27th August, 1970, were taken as read. Their adoption, which was proposed by Mr N. A. Honnet and seconded by Mr J. G. Kirchner, was carried unanimously. MINUTES OF THE JULY GENERALMEETING The minutes of the General Meeting held on the 8th July, 1970, were taken as read. Their adoption, which was proposed by Mr C. J. Isaac and seconded by Mr J. G. Kirchner, was carried unanimously. GENERAL BUSINESS Members were advised that no more applications could be entertained for the visit to Western Holdings; they could, however, still apply to visit Welkom Mine and Harmony. TALK The Chairman invited Mr A. Paschalides to deliver his talk on 'Controlled blasting in stopes and new explosives developments'. The presentation proved to be of great interest to the meeting and lively discussion followed the talk. Mr N. A. Honnet proposed a vote of thanks to Mr Paschalides on behalf of all members of the O.F.S. Branch. CLOSURE The Chairman thanked Mr Paschalides for his talk and all present for their attendance, and as this was the last meeting for 1970 he wished all members a Merry Christmas and a Happy New Year. He declared the meeting closed at 9.30 p.m.

By R. C. Earlougher

Jan 1, 1970

By John P. Turner, Benjamin J. Turner

"Non-destructive testing and evaluation (NDT/NDE) methods have become standard tools as part of the post-construction quality assurance of drilled shaft foundations. In responding to anomalies, foundation designers, owners, and contractors face a number of choices, including: (i) acceptance of a shaft with known anomalies, (ii) further investigations of integrity (e.g., concrete coring), (iii) repair schemes, and (iv) reject and replace. To assist in selecting the best option, analyses are often performed that involve assessing the structural performance of reinforced concrete shafts that may include defective concrete or voids. Currently, the analytical tools for predicting the flexural strength and stiffness of drilled shafts with defective concrete located in discrete regions of the cross section are limited. This paper presents a robust moment-curvature analysis tool for drilled shafts based on the fiber-element discretization method. The tool allows for consideration of anomalous or defective concrete regions in the shape and location that they are believed to exist in the shaft while considering explicitly the nonlinear material behavior of the intact regions based on expected material properties. A case study is used to illustrate the practical application of the analysis to drilled shaft projects.INTRODUCTIONImperfections such as defective concrete or accidental eccentricity of reinforcing cages are an inherent part of the drilled shaft construction process that will occur occasionally even when construction best-practices are followed. Petek et al. (2002), O’Neill and Sarhan (2004), Poulos (2005), and others have described the effects that construction defects can have on the axial and lateral performance of drilled shafts. Our industry has seen rapid progress in recent years in the development and improvement of tools for detecting drilled shaft anomalies, such as gamma-gamma and crosshole-sonic logging, sonic-echo testing, thermal integrity profiling, and even visual inspection with invasive video cameras. Nonetheless, in most cases the wealth of data from these tests is used by foundation engineers to make a fairly “black or white” decision—should the defects be repaired, or should the shaft be rejected? A third option that is not typically considered is to directly analyze the section, including anomalies, and compare the reduced strength and/or ductility to the actual project demands. This option takes full advantage of the data collected during integrity testing, and may provide a justifiable means for avoiding further construction costs and delays, whether for repair or replacement."

Jan 1, 2016

By C. A. Johnson, K. F. Unrug

The identification of the major subsidence areas in the Eastern Kentucky Coal Field has been made to distinguish the subsidence phenomena on the basis of geographical location. Further, this identification process is based upon selected critical geological, topographical, and mining features in the coal fields. The proposed identification of the regions is derived from a comparison of the subsidence potential in a particular area. The most likely severe subsidence areas are compared to those with the probable low subsidence severity. The combination of certain geological and mining parameters involved allows for the derivation of a classification of the subsidence potential.

Jan 1, 1986

By J. E. Shigley

The gemological properties that allow natural emeralds and blue sapphires to be distinguished from other gemstones are summarized in this paper. A variety of synthetic and laboratory-treated emeralds and blue sapphires are also encountered in the jewelry industry today. Gemologists distinguish these latter materials from their natural counterparts based primarily upon features seen with magnification, such as inclusions and/or growth zoning. In some cases, however, these observations and standard gem-testing methods are insufficient, and the use of non-destructive analytical methods, such as optical spectroscopy and chemical analysis, are required for positive identification. The commercial value of synthetic and treated gems are much less, and can be insignificant in comparison to that of an important untreated natural gemstone. Identification of synthetic and treated gem material is essential to maintaining integrity in the jewelry industry. Loss of consumer confidence in the gemstones sold at the jewelry counter could have a negative impact on the exploration and mining of natural emerald and blue sapphire.

Jan 1, 1998