Search Documents

By Zhang Libo, Wang Xin, Peng Jin-hui, Ju Shaohua, Guo Sheng-hui, Xu Lei, Huang Meng-yang

"China is lacking high grade titanium ores. This work intends to leach impurities such as Fe, Ca and Mg from a low grade titanium ore, to increase the grade. The original material contained 65% TiO2 , 16.12% Fe, 9.4% CaO + MgO, 4.2% SiO2, 1.25% A12O3, and the particle size is between 0.053-0.045mm. Microwave energy was used to enhance the leaching effect. The results showed that when normal heating was used to leach the mineral, the extraction of impurities Fe, Ca and Mg was very low. However, when microwave energy is introduced, the extraction of Fe, Ca and Mg increased dramatically. The optimized conditions are: relative power 5W/g, the ratio of concentrate to HC1 isl5%, leaching at 160°C for 20 min with a ratio of liquid to solid 12:1 mL/g. The material obtained under these conditions contains 92.73% TiO2, 0.207% Ca + Mg, 0.8% Fe, with 94.6% Ti recovery. The poduct meets with the quality for boiling chlorine.IntroductionThe resources of titanium are very abundant, and are distributed all over the world. There are almost 140 minerals containing TiO2 with a content of more than 1%. However, there are only several minerals which can be used for producing sponge titanium. They are mainly rutile and ilmenite. The grade of nature rutile concentrates is higher than 95% TiO2, and it is a high quality raw material. But the resources of nature rutile are relatively low; after mining for many years, its resources are exhausting gradually. Although ilmenite reserves are great, ilmenite cannot be used as a raw material because of its low content of TiO2, only 45-70%; also it has a high impurity content of Ca, Mg and Fe. In these years, there is a tendency for titanium industry to use high grade concentrate."

Jan 1, 2012

By Hong Yong Sohn, Miguel Olivas-Martinez, Zhixue Yuan

A novel flash ironmaking process that directly reduces iron oxide concentrate particles by gas is under development. The goal of this work was to study the possibility of reoxidation of iron particles in various gas mixtures. As the product iron cools down in the lower part of the flash reactor, conditions may become favorable for reoxidation because of equilibrium and high reactivity of iron particles. The effects of temperature (823 – 973 K) and H2O partial pressure (40 – 100 pct., Ptotal = 86.1 kPa) on the reoxidation rate were examined. The pressure dependence was first order with respect to water vapor, and the activation energy was 146 kJ/mol. A complete rate equation that adequately represents the experimental data was developed. For oxidation in O2-N2 mixtures, the effects of temperature (673 – 873 K) and O2 partial pressure (5 – 21 pct., Ptotal = 86.1 kPa) were determined. Reoxidation in pure CO2 was also investigated at 873 – 1073 K for comparison.

Jan 1, 2014

By . Menad Gaballah I

Three samples of solid wastes generated by the non ferrous metallurgy were characterized. These residues contain up to 42 % of valuable metal compounds ( Cu, Pb and Zn ) and 23 %of toxic compounds t As, Hg, Cd and Se ). These sample were subjected to thermal treatments between 200 DC and 800 °C in controlled oxidizing. reducing and chlorinating atmospheres. Up to 99 % of As, Cd, Hg and Se were eliminated from these industrial wastes. Cu, Pb, and Zn compounds were concentrated in the treatments' residues of these samples. A Global Decontamination Factor' GDF ' was defined to measure the efficiency of the elimination of toxic elements and the recovery of valuable elements for a specific sample submitted to a given treatment. It seems that the thermal treatment in a reducing atmosphere was the most efficient in decontaminating these solids and the concentration of valuable elements. a.

Jan 1, 1995

By Evgenii Pavlov, Ivan Tronin, Viktor Timofeev, Vladimir Kislov, Sergei Bogovalov

"Modeling of the magnetohydrodynamical (MHD) and thermodynamical processes during the industrial scale Direct Chill (DC) casting of aluminum slabs is performed using a combination of ANSYS/CFX and ANSYS/EMAG software. The electromagnetic field is modeled through ANSYS/EMAG, while hydrodynamic and thermodynamic processes are modeled through ANSYS/CFX. Both packages were modified in order to calculate MHD flows in the liquid pool that forms during aluminum DC casting, and they were unified into a software combination that provides simultaneous simulation of all the above processes. The simulation shows that the electromagnetic stirring of the molten aluminum changes the shape of the solidification front (solid-liquid interface) very dramatically, namely it becomes significantly flatter. This effect should improve the internal structure of aluminum DC slabs and allows us to increase the casting velocity.IntroductionProduction of Aluminum alloys with high mechanical properties and structural uniformity is one of the main goals of industry. The preferred production method of aluminum alloys in most modern plants is Direct Chill (hereafter DC) casting because it offers high productivity and commercial success. One important limitation of this technology is the development of centerline shrinkage in slabs larger than about 1 meter. The improvement of the internal structure of long DC cast slabs can be achieved by electromagnetic stirring (hereafter ES) of the liquid metal above the solidification front. This intensifies heat transport in the zone close to the solidification front and suppresses shrinkage formation."

Jan 1, 2013

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"Reduction of combustion-emitted greenhouse gases, which are associated with global warming, may be achieved by use of CO2-neutral alternative fuels, such as bio-ethanol. Distillers Dried Grains with Solubles (DDGS) are the main co-products of the com-grain-based ethanol industries. In 2009, the North American production of ethanol from com was about 38 billion liters, which generated approximately 31.5 million tons of DDGS. Samples of DDGS were pyrolysed at temperatures of 600-1000 °C in a two-stage laminar-flow horizontal furnace, and a catalyst system was used to synthesize nanomaterials. This work presents a microstructural characterization of these nanomaterials by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Results showed that the nanomaterials produced from pyrolysis of DDGS were in the form of long, entangled, rope-like structures with rugged walls, lengths in the tens of microns, and axially non-uniform diameters in the range of 100-300 nm.IntroductionThe interest in ethanol has increased considerably worldwide due to the necessity of finding renewable and cleaner energy resources [1, 2]. According to the Renewable Fuels Association (RF A), the world ethanol production in 2008 was approximately 65.7 billion liters (17.3 billion gallons), which figure represented a 24% increase in the production over that in the previous year [3]. The major producers of ethanol are the USA and Brazil, which together account for 90% of world production. The main feedstock for ethanol in USA is com grain, whereas sugarcane predominates in Brazil [2-4]."

Jan 1, 2011

By Zhihong Liu

Monodisperse micron size nickel oxalate particles with rhombohedron morphology were prepared from condensed Ni(OH)2 suspension by a novel gel-sol process proposed by one of the authors. Firstly, condensed nickel hydroxide gel was formed by fast adding 1 mol dm-3 NaOH solution into 0.2 mol dm-3 nickel chloride solution, and then oxalic acid solution with a concentration of 0.25 mol dm-3 was dropped into the gel drop wise through a pump equiped with a pH controller under preset pH value, and in this process, Ni(OH)2 gel was converted gradually into monodisperse nickel oxalate sol. The formation of the nickel oxalate particles was found to proceed through a dissolution-recrystallization mechanism from the nickel hydroxide gel. The product particles exhibited rhombohedron like shape with micron size long axis and sub-micron size short axis. The effects of such factors, as temperature, surfactants, et al, were evaluated experimentally on the particles sizes and morphologies.

Jan 1, 2006

By R. Tunold, Y. J. Zhang

"The cathodic kinetics of aluminum deposition from aluminum chloridealkali chloride melts was studied by use of electro-cnemical transient techniques at 700 °C. Aluminum deposited as an insoluble product on a glassy carbon electrode and as a partly soluble product on a tungsten electrode. The deposition was found to be a simple diffusion controlled process involving the exchange of three electrons. The diffusion coefficient of aluminum chloride was calculated - 4.sx10-s cm2 ·S-I in AlCl3 -NaCl-LiCl melts and 2.6x10-s cm2 ·S-' in AlCl3 -NaCl-KCl melts. For AlCl3 -NaCl-CsCl system the diffusion coefficient exhibited some uncertainty due to nucleation. The determined rate constant of aluminum deposition reaction was on the order of 10-' -10-2 cm'S:' Constant potential electrolysis was carried out. TiB2 was well wetted by aluminum. The species of melts penetrated into graphite and glassy carbon but not into tungsten. The diffusion coefficient of species in glassy carbon was evaluated.IntroductionAluminum chloride electrolysis is attractive for its power saving of 30%. Different process to circumvent the conventional chlorization to obtain aluminum chloride economically, such as directly chlorizating mixture of Al~03 and C in a cell with A-shaped laminated bipolar electrodes by rising chlorine (1), or by use of a composite anode (2), will promote the electrolysis technology to be realized industrially. With the appearance of the Alcoa process periodically there are studies on the kinetics of aluminum deposition. Some discrepancies seem to exist on the mechanism of aluminum deposition. Borne studies (3,4,5) showed that the deposition of aluminum was hindered by diffusion process in the melts. M.Gabco et a1. (6) claimed a preceding dissociation of a complex being the rate controlled step. This paper presents our results on the mechanism of aluminum deposition from the study by use of transient techniques and some results from constant potential electrolysis."

Jan 1, 1988

By Carl C. Nesbitt

A process has been developed to recover and recycle metals from wastes of brass foundries which contain copper, zinc and lead in various quantities. Tests were conducted to evaluate several leachants, including sulfuric acid, ammonia, hydrochloric acid, cyanide and acetic acid, and to determine the optimum leaching conditions, such as air flow rate, initial copper ion concentration, temperature, and agitation strength. Sulfuric acid containing copper sulfate with dissolved oxygen is the most successful leachant. More than 99% of the copper and zinc originally present in the waste was dissolved, while only 0.5% of the lead entered the solution after 14 hours of leaching. The leaching mechanisms of copper, zinc, and lead are proposed. The copper and zinc can be recovered from the solution by electrolytic processing. The unleached residue may be converted to a lead carbonate which can be converted to litharge at 400-450°C and to massicot at temperature above 500°C by calcination.

Jan 1, 1995

By J. Y. Foley

Platinum-group elements (PGE) are preferentially associated with chromian spinels, including high-iron chromite, magnesian-chromian hercynite, and chromian magnetite in clinopyroxene-rich upper stratigraphic portions of the Tonsina ultramafic complex in southern Alaska. Ratios of Pt:Pt+Pd are proportional to chromium content in the associated chromian spinels. The maximum PGE content of geochemical rock samples from Dust Mountain is greater than 20.000 ppb (>0.6 oz/ton) with minor gold values. The maximum PGE content of tabled chromite concentrates is 3.430 ppb (0.1 oz/ton) at Dust Mountain. 1.029 ppb (0.03 oz/ton) at Sheep Hill, and 1,749 ppb (0.051 oz/ton) at Bernard Mountain. High-iron chromite at Dust Mountain yields tabled chromite concentrates with Cr:Fe ratios between 0.5 and 1.2. Lower PGE contents are found in more chromium-rich chromitites from Sheep Hill and Bernard Mountain that yield concentrates with Cr:Fe ratios between 1.0 and 2.8. Platinum-group minerals include amalgams. arsenides. PGE alloys, and sulfides. These minerals are between 3 and 40 microns in size and are concentrated along grain boundaries and fractures of metasomatically and hydrothermally altered chromian spinel grains.

Jan 1, 1987

By Atul Kurnar

In the present research a two-cell polymer electrolyte membrane fuel cell stack (PEMFCS) with SS-316 bipolar plates has been tested. Different flow field designs were studied and a modified multi-parallel channel design is proposed. The stack is stable within ±3 mV even after 1000 hours of continuous operation, indicating efficient water management and effective removal of any metal ions from the stack. Also no iron is detected in membrane electrode assembly (MEA) by EDAX analysis after 1000 hours of cell operation. Results indicate that high operating pressures beyond 138 kPa didn't significantly increase the performance of cell, however added much to the pressurization cost of the system. Tests at different temperatures showed that at temperatures below 80°C, external humidification could be completely removed. The prototype stack is also tested under variable load conditions simulating highway-driving schedule. The experimental efficiency of PEMFCS is 48%, which is in good agreement with the model predicted efficiency of 53.8 %. Results show that 59% of the total losses are due to ohmic polarization in the cell. Further analysis on applications of the stack in automotive transportation system is in progress.

Jan 1, 2002

A study of iron-removal from copper leachate by limestone precipitation followed by direct eltctrowinning of copper has been conducted. The influence of the process parameters: amount of precipitant, contact time, temperature, agitation intensity, solution acidity, and initial iron concentration on iron-removal was investigated. The effects of electrowinning time, cell voltage, solution acidity and temperature on electrowinning of copper were also investigated. The leachate contained 1.20 g/l cu2+ and 7.41 g/l total iron at pH 2.27. After contacting with 14 g/l precipitant for 2 hours, 97.5 % of the iron was attenuated and 98.4 % of the copper was recovered. With the following electrowinning conditions: 3 lead anodes, 3 stainless steel cathodes, 2.5 V, 39.41 A/m2 and 10.7 g/l H2S04, copper recovery-was 98.4 %. Purity of copper powder produced was greater than 99.0 %.

Jan 1, 1999

By H. Conrad, K. Jung

"The effect of an external electric field E=5(+) kV/cm applied during the solution heat treatment at 500°-550°C of three commercial Al-Mg-Si alloys (AA6061, AA6022 and AA61l1) on the asquenched resistivity Pw and hardness H.,NULL, w was investigated. It was found that the field gave a significant increase in Pw and in Hv,w, for AA6022 and AA6111, but had no clear effect on AA6061. Thermodynamic analysis gave that the effect of the field on AA6022 and AA6111 was to reduce both the enthalpy ?H, and entropy ?H, of solution. Considering the chemical composition of the three alloys it appears that the influence of the field may depend on the amount of Cu plus excess Si present in the alloy.IntroductionKlypin and Soloviev [1, 2] were the first to report that the application of an external electric field during solution heat treatment (SHT) of Al alloys gave an increase in the as-quenched resistivity and hardness. They attributed these effects of the field to an increase in solubility of the alloying constituents during the SHT. More recently Liu and coworkers [3, 4] also reported an increase in the as-quenched resistivity of Al-Li alloys with application of an electric field during SHT. Further, the present authors [5] found that the application of an electric field during the SHT of the commercial Al-Mg-Si alloys AA6022 and AA61i1 increased their as-quenched resistivity and hardness. Their thermodynamic analysis of the results indicated that the field decreased both the enthalpy ?H, and entropy ?S, of solution."

Jan 1, 2004

By Pengfu Tan

A thermodynamic model and computer program, CuModel, has been developed to model the distribution behaviors of Cu, Fe, S, O, Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag, copper loss in the slag, and heat balance in copper smelting process, matte converting process and copper con-tinuous smelting process. It can be predicted for any set of controllable process parameters such as feed composition, smelting temperature, degree of oxygen enrichment and volume of oxy-gen-enriched air. This model accounts for physical entrainment between matte and slag phases. It can be used in Isasmelt process, copper flash smelting process, Mitsubishi process, P-S con-verting process and Noranda process. The predictions by the present computer model are com-pared with the known commercial data from Guixi Smelter in China, PASAR Corporation in Philippines, Horne Smelter in Canada, MIM Limited in Australia and Naoshima Smelter in Ja-pan. The agreements between the computer predictions and the commercial data are excellent. In this paper, the applications of CuModel in the copper metallurgical industries have been pre-sented. CuModel has been used by Daye Smelter and Guixi Smelter in China, and by PASAR in Philippines as well.

Jan 1, 2004

By Mototsugu Matsuno

A new process has been developed to treat fly ash generated from municipal incinerators, which contains not only toxic metals such as lead and cadmium, but also dioxins. The process includes the following steps; fly ash is formed into green pellets with some additives and the pellets are then roasted to eliminate or stabilize the toxic metals and to decompose dioxins. A pilot plant with a capacity of approximately 100 kg/hr was used to test the process. The tests verified that heavy metals were either volatilized or stabilized and dioxins were decomposed by high-temperature roasting. The pelletized ash was found to be non-toxic, so that it can be recycled as artificial lightweight aggregate. It was also found that volatilized metals collected as secondary ash can be recycled as smelting resources.

Jan 1, 2003

By James Vaughan

Australia is a major miner of ore that requires hydrometallurgical processing. According to the 2016 US Geological Survey Minerals Commodities Summaries, the country is 1st for aluminium (bauxite) and lithium, 2nd for gold, zinc and cobalt, 4th for nickel and silver, and 6th for copper mining, not to mention its wealth in coal and iron ore. In this paper, examples of recent Australian hydrometallurgical activities are summarised. Then, selected research projects from the University of Queensland hydrometallurgy research group are profiled. The projects profiled are related to fundamental aspects of processing bauxite with organics and reactive silica as well as the development of a synergistic hydro- and pyrometallurgical process for copper. The process context and motivation for the research is introduced, key results are highlighted with the associated relevant references.

By Zhang Chuanfu, Tan Pengfu

"A thermodynamic model is developed to predict the distribution behaviors of Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag in copper pyrometallurgical process. In this model, as more as 21 elements (Cu, S, Fe, Ni, Co, Sn, As, Sb, Bi, Pb, Zn, Au, Ag, 0, N, C, H, Ca, Mg, Al, and Si) and 72 compounds (in fayalite-slag-making system) or 74 compounds (in ferrite-slag-making system) are considered. Accessory-element behavior is studied for two types of slag , fayalite and ferrite, and two levels of oxidation. The allowance is also made to account for physical entrainment in the melts.-Model simulations are carried out to study the effects of controllable process parameters such as feed composition, smelting temperature, degree of oxygen enrichment and volume of oxygen enriched air. The model can be used in copper flash process, Mitsubishi process and Noranda process. The predictions by the present computer model are compared with the known industrial data from Gui Xi Smelter in China, Home Smelter in Canada and Naoshima Smelter in Japan and excellent agreement between calculations and industrial data is obtained. In this paper, the effects of oxygen enrichment, matte grade, smelting temperature, and types of slag on accessory-element behavior among matte, slag and gaseous phase have been elucidated.I . IntroductionThe presence of trace quantities of minor elements such as As, Sb and Bi in copper significantly reduces its ductility, electrical conductivity, and lowers its thermal conductivity. Embrittlement of copper also occurs due to impurity-phase precipitates at the copper grain boundary interfaces. They deteriorate not only the electrical conductivity of copper but its workability in hot working."

Jan 1, 1998

By I. Peerawattuk

Growing demand for Li-based battery technologies is leading to an unprecedented growth in the lithium industry. Although innovation in battery technologies has pushed lithium into the spotlight, lithium was not always known for its application in batteries. The primary use of lithium—prior to the introduction of commercial lithium-ion batteries in the early 2000s—was in the ceramics, glass, grease, and the medical industry. Before being converted into usable forms, lithium products must be upgraded from the raw material. Processes for recovering lithium may involve: thermal treatment, water leaching, solar evaporation, ion exchange, carbonation, and electrodialysis. Presented, is a historical review of lithium applications and the different techniques of converting lithium-rich minerals and brines into usable products with additional discussion on future lithium extraction processes.

By Mitsutaka Hino

The contents of gangue minerals, such as Al2O3. P2O5, crystalline water and so forth in the iron ore imported to Japan tend to increase year by year. Though the increments of such gangue contents arc approximately 0.1-0.2 mass%, some problems for the blast furnace operation in ironmaking process have already been reported, In order to clarify the mechanism of harmful effect caused by the small increment of gangue minerals, mainly Al2O3. on the blast furnace operation, the dripping behavior of Fe,O-CaO-SiO2-Al2O3-MgO slag from the iron funnel, which simulated the micro-porosity in sinter ore, has been observed with the wide range of basicity, Al2O3, Fe2O and MgO contents. The effect of MgO on the dripping behavior of slag has been summarized in this paper. It was found that the addition of 2mass% MgO resulted in large increase of hold-up on the most of the conditions. When Fe2O content was less than 20mass% and the basicity was lower than 0.8, MgO lowered the hold-up even if the slag contained 10mass% Ah03. Every slag hold-up showed the minimum at the basicity of less than unity on the conditions of constant Fe2O and Al2O3 contents, This trend became remarkable when the slag contained 2 mass% MgO.

Jan 1, 2003

By D. J. Chaiko

Aqueous biphasic extraction (ABE) processes offer the potential for low-cost, highly selective separations. This countercurrent extraction technique involves selective partitioning of either dissolved solutes or ultrafine particulates between two immiscible aqueous phases. The extraction systems that we have studied are generated by combining an aqueous salt solution with an aqueous polymer solution. We have examined a wide range of applications for ABE, including the treatment of solid and liquid nuclear wastes, decontamination of soils, and processing of mineral ores. We have also conducted fundamental studies of solution microstructure using small angle neutron scattering (SANS): In this chapter we review the physicochemical fundamentals of aqueous biphase formation and discuss the development and scaleup of ABE processes for environmental remediation.

Jan 1, 1996

By Harsh Deep Chopra, Jason N. Armstrong, Susan Z. Hua

"Existence of anisotropic Curie temperature materials [E. R. Callen, Phys. Rev. 124, 1373 (1961); J. Appl. Phys. 32 S221 (1961)] is a longstanding prediction - materials that become paramagnetic at a lower temperature along certain crystal directions while remaining magnetically ordered in other directions up to a higher temperature. Validating Callen's theory, we show that all directions within the basal plane of monoclinic F e1Ss (pyrrhotite) single crystal remain ordered up to 603 K while the c-axis becomes paramagnetic at 225 K. Results prompt a re-evaluation of existing magnetic materials with a focus on magnetic characteristics along different crystal orientations above instead of below the ordering temperatures. Theoretical guidelines for identifying new materials with large anisotropy of Curie temperature are also given, and analysis protocol to characterize them in a self-consistent manner is discussed. Materials with such a large directional dependence of Curie temperature open the possibility for uniquely new devices and phenomena, including energy storage and spintronics devices.IntroductionThis paper is an overview of our recently published work on anisotropic Curie temperature materials [l]. As a background, ferromagnetic and ferrimagnetic materials are characterized by a critical temperature below which magnetic interactions prevail over thermal agitation, leading to the appearance of a spontaneous magnetization. Above this critical point, called the Curie temperature, thermal energy eventually overcomes magnetic interactions and the material becomes paramagnetic.It is less well known that the Curie temperature varies with the orientation of the crystal. In ordinary ferromagnets this orientation dependence of Curie temperature is negligible because of the vanishingly small ratio of anisotropy to exchange energy, i.e., the spherical or isotropic exchange term dominates. Thus Curie temperature in ordinary ferromagnets appears to be an isotropic property, and assigning it a single characteristic ordering temperature suffices. However, a 'small' difference is not equivalent to being the 'same', and under appropriate set of conditions the anisotropy of Curie temperature is predicted to become appreciable, as discussed in the following.In formulating the theory of 'anisotropic magnetization' [2, 3] E. R. Callen and H. B. Callen first discussed the ""interesting possibility"" of anisotropic Curie temperature [2] or ACT; Callen and Callen noted that it was W. J. Carr, Jr. who initially raised this question, and they discussed it in detail at the Conference on Magnetism and Magnetic Materials (NY, November 1960), see footnote on page 320 of Ref. [2]. Soon thereafter, E. R. Callen developed the theory underlying the anisotropy of Curie temperature and conditions conducive to its observation [4, 5]."

Jan 1, 2013