Search Documents

By N. A. McKay, J. G. Davison

"Heap leachable ore deposits from many countries have been submitted for process mineralogical evaluation and laboratory testwork. Numerous factors must be addressed and integrated by the mineralogist, geologist, metallurgist and engineer. Projects encompass grass roots exploration, preliminary petrographic analysis, predictive and process mineralogy, dye penetration analysis of rocks and thin sections, metallurgical beneficiation testwork and plant optimization studies. The significance of mineralogical factors, such as geological controls, degree of oxidation, dye amenability, liberation, deleterious minerals, refractoriness, and the impact of mineralogy on gold recovery and process considerations, will be presented.ABSTRACT ONLY"

Jan 1, 1997

By Daniel Helm

The first industrial application of direct solvent extraction of nickel from hypersaline sulfate feed solutions has highlighted the need to investigate the influence of chloride on the extraction behaviour nickel in the presence of calcium using Versatic 10 and the solubility characteristics of gypsum. Temperature-solubility curves for gypsum in various aqueous electrolytes were prepared. The solubility of gypsum is increased significantly by the presence of sulfate ions, while chloride ions decrease it for a given temperature. The anion effects of chloride and sulfate on the extraction of calcium and nickel by Versatic 10 corresponded well with the complexing ability of the anions. It was shown that the presence of chloride shifts the extraction isotherms for both metals significantly to the left, while decreasing the selectivity of Versatic 10 for nickel over calcium. The loading of nickel onto Versatic 10 in this system was shown to be at a maximum within 3 seconds, while calcium extraction took between 4 ? 5 seconds to load to a maximum. Chloride ions had no influence on loading kinetics of nickel, but depressed the rate of calcium loading. It was shown that in the presence of an excess of nickel, calcium loading is effectively eliminated, and that calcium is scrubbed from Versatic 10 within 2.5 seconds of contact with nickel electrolyte.

Jan 1, 2003

By Marco A. S. Aguiar, Luis G. S. Sobral, Vânia Mori, Paulo A. Medeiros da Silva

"Copper occurs in the crust of the earth, predominantly, as sulphides. Among the copper sulphide minerals, the chalcopyrite is the most abundant and the most refractory to the conventional oxidative processes. This work aims at developing an electrolytic process for treating a copper sulphides flotation concentrate, more precisely chalcopyrite (CuFeS2) and bornite (Cu5FeS4) in the percentages of 70 and 30%, respectively.This paper presents a low-cost operational electroleaching process for treating copper sulphides flotation concentrates, with a high chalcopyrite content. This research practical work aims at improving the copper extraction from that sulphide mineral, in a relatively short time with low-operating cost taking into consideration the influence of a cationic surfactant. The electrolyte of the electrolytic reaction system was a 2,0 mol.L-1 NaCl solution containing CTAB, a cationic surfactant. The electroleaching system contains one DSATM (dimensionally stable anode) anode and two nickel or copper foams (threedimension electrodes. During the electroleaching process the chloride ions are oxidized to chlorine at the anode surface, which in contact with the aqueous phase generate enough hypochlorite ions to oxidize chalcopyrite.The copper ions released from the chemical oxidation process are reduced at the cathode surface as metallic copper."

Jan 1, 2008

By M. Benavides

An experimental study is carried out With sulphide ore obtained from Bailadores-Venezuela as well as artificial concentrates. Concentrates of the minerals from froth flotation are fused to study equilibrium between the matte and slag phases. The first part of the work deals with obtaining a concentrate by flotation experiments with collective and selective reagents, with acceptable metallurgical recovery, studying the influence of different parameters in the process. The second part gives the results of the experimental investigation. on thermodynamic equilibrium in smelting which facilitates knowledge of the elemental processes, giving bases for the possibilities of reducing the loss of metal in slag.

Jan 1, 1983

By W. L. Cornell

The processing of lead tailings for removal of the heavy metals produces concentrates upgraded in Co and Ni values. Reflected light microscopy, scanning electron microscopy, image analysis, and Vickers hardness measurements were used to identify mineral species, associations, degree of liberation, and distributions to the test products. Siegenite and bravoite were the most common species encountered, but violarite and enriched pyrite and marcasite phases were also identified. Liberation for the Co and Ni minerals contained in the tailings was 20 micrometers or less.

Jan 1, 1993

By B. G. Belew

Recent operating improvements at the Phelps Dodge Chino Smelter, coupled with intensive capital expenditures since 1987, have resulted in a safer, higher quality, more productive smelter. This paper briefly reviews the flowsheet of the Chino Smelter with emphasis on recent capital expenditures. The main focus of the paper is to provide case studies of how operating functions have been improved. Case studies presented include: (1) safety, (2) anode quality control, (3) flash furnace cross-over build-up control, and (4) flash furnace temperature control. Most of these accomplishments have been achieved by providing specific measurable goals and subsequent feedback to operating crews.

Jan 1, 1993

By Mark C. Bronson

The feasibility of several pyrochemical approaches-for separating non-radioactive constituents from ICPP HLW calcine were examined. The removal of aluminum as AICI3 from aluminia calcine was successfully demonstrated. The examination of pyrochemical processes to remove non-radioactive constituents, primarily aluminium, zirconium, calcium and fluorine, from zirconia calcine showed that fluorine removal was required in order to chlorinate the calcine. A molten calcium chloride wash, a calcium reduction, and. a sulfuric acid treatment were examined as possible zirconia calcine pretreatment options for fluorine removal. Fluorine removal from simulated ICPP zirconia calcine was demonstrated by both a CaCl2 wash method and a sulfuric acid treatment method. X-ray fluorescence analysis indicated that greater than 97% of the fluorine can be removed by either method. Fluorine removal by a calcium reduction using an alloying agent, zinc, or a calcium reduction using, a filtration separation were also demonstrated, but the efficiencies of fluorine removal were considerably less ranging from 50 to 90%. Regeneration of CaCl2 from the salt and oxide residues of the CaCl2 wash experiments was also demonstrated 'by an aqueous dissolution method. From the salt residue, 85% or more of the CaCl2 was recovered and contained little if any CaF2 or CaO. From the oxide residue close to 100% of the CaC12 was recovered. Because of the overall success of the CaCI2 wash, it was determined to be the preferred fluorine removal process. The sulfuric acid treatment to remove fluorine is effective, but the proposed overall flowsheet has not' been adequately demonstrated.

Jan 1, 1995

By H. Cepin

Production of non-ferrous metals is still principally performed in shaft and flame fired furnaces. Electric furnaces increase metal recovery, reduce environmental burdens and decrease energy consumption compared to conventional processes. Because non-ferrous metals have low melting and boiling points and aggressive slags design of the furnace, energy input, and slag conductivity and composition are very important. Secondary materials are easily handled in electric furnaces. Since additional amounts of lead, zinc and tin will become available from secondary sources in the future, electric furnaces are expected to replace conventional smelting furnaces. The paper describes technical, electrical, and process designs of electric furnaces peculiar to the reduction of non-ferrous metals. Electric and various thermic furnace processes are compared.

Jan 1, 1990

By Akram Salah Eddine Belaidi, Lakhdar Azzouz, Benchaa Benabed

"The dunes sand is a material of a large availability in Algeria. This material is practically unexploited. The introduction of this material as a new element in the construction can be more relieve the domain of building, and contribute to the development of the southern regions of Algeria, which are very rich in this material. The main objective of our work is to exploit a largely available material in the Algerian south which is the dunes sand, as a material of construction in the region of Laghouat.In this study, first we investigated the effect of the curing environment and the nature of the sand on the mechanical properties of the mortar, such as; flexural and compressive strengths. Then after, we studied the durability of the mortar under cycles of wettingdrying and the chemical attack of sodium sulfate (Na2SO4 5%).According to the results, we note that the mortar of the sand mixes (river sand plus dunes sand) present the best mechanical performances under different environment of curing. In addition result of durability studies put forward that the mortar of the sand mixes is more resistant to the sulfates attack."

Jan 1, 2008

By B. J. Beaudry

The preparation of alloys containing one to two percent of the volatile lanthanide metals Sm, Eu, Tm and Yb in the high melting point (HMP) rare earth metals Sc, Y and Lu was accomplished by a vapor deposition, diffusion method without crucible contamination. The method avoids the melting of the HMP metals which would introduce impurities from the crucible, generally Ta or W. Plates of the HMP metals were hung from the lid in the upper part of the Ta crucible. The volatile metals were placed on the bottom and the lid welded in place under an atmosphere of helium. By proper selection of thee alloying temperature, the effusion of the metal vapors, through the helium atmosphere was slow enough to permit diffusion to occur and prevent refluxing of the newly formed alloy. Very volatile metals such as Mg required a Knudsen cell with a suitably sized hole to prevent too rapid transfer of the low melting metal. Electron microprobe analysis of a cross-section of the HMP metals showed a homogeneous distribution of the volatile metals. The time and temperature required to obtain a homogeneous rare earth alloy without contamination are given. The use of a Knudsen cell to form magnesium-rare earth alloys is reviewed.

Jan 1, 1992

By W. G. Davenport

The paper "Copper Smelting to the Year 2000" was presented at the CIM Conference of Metallurgists in Sudbury, August 1979. That paper predicted, in part, that high matte grade, high oxygen smelting - particularly in flash furnaces - would dominate copper smelting until the beginning of the next millennium. The present paper re-evaluates that prediction and examines the changes that have occurred and will occur in copper extraction in the 1990's. Of particular interest is the question as to whether major competitors are on the horizon for flash smelting and Peirce-Smith converting. Recent results with direct-to-blister smelting, lance smelting and submerged-tuyere smelting are reviewed and their roles in future copper smelting are predicted. Requirements for H2SO4 plants which handle the off-gases from modern smelting/converting processes are also examined.

Jan 1, 1993

By Yongxiang Yang, Yanping Xiao, Robert G. Harskamp

"Stricter environmental regulations demand for safer treatment and disposal of incineratior fly ashes. So far no sound technology and processes are available for a sustainable and ecological treatment of the waste incineration ashes, and only partial treatment is practised for temporary and short-term solutions. New processes and technology need to be developed for comprehensive utilization and detoxification of the MSW (Municipal Solid Waste) incinerator residues. The objective of the current research is to better understand the behaviour of the environmental harmful elements during low or high temperature treatment, and to find an optimum route for an efficient processing of the incineration fly ash. In the present study, the fly ashes including boiler ash and ESP (Electrostatic Precipitator) ash sampled from a MSW incinerator were washed with warm water, and the residues were dried and sintered or vitrified at high temperatures. The solutions from ash washing were analysed, and will be treated for salt extraction and purification. The ash residues before and after thermal treatment were also analysed. The results of vitrification and thermal behaviour were compared with those from the ashes without pre-washing. It was found that water pre-washing is an efficient way to remove certain water-dissolvable volatile salts such as chlorides, and thus the secondary emissions during vitrification could be reduced. INTRODUCTION The air pollution control residues from MSW incineration are classified as harzardous waste, including boiler ash, ESP ash and filter cake. The boiler ash is the firstly settled flue dust in the dust-collecting equipment under the boiler, the ESP ash is collected by an electrostatic precipitator in the second step, finally the flue-gas is further cleaned by the wet-scrubbers and residues are accumulated in the filter cake. Both the boiler ash and ESP ash are classified as hazardous materials, harmful to the environment due to the high concentrations of environmental hazardous elements. However, due to the different locations of the ash collection, the boiler ash has different compositions compared to the ESP ash, and is considered less toxic. Fly ash is generally toxic and with low bulk density, and has to be treated before final disposal. The current industrial practice is normally the landfilling after partial detoxification such as cement solidification."

Jan 1, 2008

By Frank Field, Elsa Olivetti, Randolph Kirchain, Elisa Alonso, Gabrielle Gaustad

"The primary technological challenge to increased use of secondary raw materials is the presence of undesirable elemental species in scrap streams. Recent literature indicates that this may become exacerbated by accumulation of impurities over time. Devising strategies to mitigate this problem depends upon understanding the mechanisms of accumulation. This paper takes a first step at characterizing the extent of this issue by presenting a simple analytical model of recycling rate for materials experiencing exponential growth. Low potential recycling rates limit accumulation due to dilution. Empirical analysis of several major materials indicates that, even for current recovery rates, theoretical recycling rates can reach above 60%, making accumulation issues a possibility.IntroductionIt is well known that recycling of secondary materials can provide significant environmental and economic benefits. Energy savings, in particular, can be quite large when substituting secondary materials for primary. Nevertheless, over the past decade, the recycling rates within the U.S. of many materials appear to not be increasing as rapidly as one would predict or even at all (Figure 1). While many barriers exist to increasing materials recycling, one that is cited consistently by the literature and producers[1-3] is compositional limitations; that is the mismatch between the characteristics of secondary materials and those desired for the finished goods into which they would be transformed..One particular aspect of compositional limitations that is receiving increasing attention is the potential for progressive deterioration of the quality of secondary raw materials streams. For some materials, for example paper or polymers, this phenomenon is inherent and relatively rapid[4, 5]. As such, it is well documented and plays a significant role in recycling decision-making even for prompt or in-house material recycling. Conceptually, this issue can manifest in other secondary materials as well, albeit through a different mechanism.As materials are mixed, used, and reprocessed during recycling, they come into contact with and often pick up other elements. The presence of these, so-called, tramp elements alters the original known composition, possibly requiring additional measurement and processing and may even preclude economic, productive reuse; ultimately, this unintentional pick up is unwanted. A growing number of studies and literature would suggest that accumulation of unwanted elements is an emerging problem, in most recycled material streams. Table I provides a brief literature review of various recycled material streams and the accumulated elements noted as problematic by various authors"

Jan 1, 2008

By K. H. Ho

This paper describes a simplified numerical model which is used to study the skull formation of liquid metal on a rapidly rotating disc in centrifugal atomisation. The skull formation is one of the problems limiting the wide use of centrifugal atomisation. The enlarging skull on the atomising disc reduces the yield of metal powder produced and produces a resistance to the centrifugal force which worsens the quality of the powder. It is costly and often difficult to study the flow behaviour by experiments due to the complex heat transfer and phase transformation during the processing. Computer modelling is therefore a powerful tool for mechanistic understanding of centrifugal atomisation. This paper investigates the flow pattern of the melt on the rotating disc as a function of initial temperature, melt flow rate and disc rotation speed as well as the physical properties of the melt, such as density, surface tension and viscosity using the commercial package Flow-3D. Keywords: Solidification, Rotating disk, Centrifugal Atomization

Jan 1, 2003

By T. Xin

A vertical grain boundary intercepting a horizontal free surface forms a groove to reduce the combined surface energy of the system. We study grooving by surface diffusion with anisotropic surface energy. A recently developed delta-function model of facets is used to describe the surface energy with three or four fold symmetry. It is found that the groove grows following a similarity law. The self-similar groove profile is solved numerically by a shooting method. Even with strong anisotropy, the groove profile can be smooth if the exposed surface orientations do not include a facet orientation. The smooth self-similar groove shape is the same as an isotropic groove, but the size is reduced by a factor that depends on the degree of anisotropy. This induces a large error on the value of surface diffusivity if the isotropic model is used for an anisotropic system. In this talk. we will describe how to correct for this error.1 I Xin, T. and H. Wong, "Grain-Boundary Grooving by Surface Diffusion with Strong Surface Energy Anisotropy," Acta Materialia 51, 2305-2317 (2003). Keynotes: Grain growth, Surface Diffusion, Surface energy, Anisotropy

Jan 1, 2003

By Junji Shibata

The waste acid mixture whose main component is phosphoric acid, is discharged from the etching process in the liquid crystal production industry. In order to separate impurity acids from the phosphoric acid, trioctyl phosphate (TOP) is used as an extractant. TOP can extract acetic and nitric acids selectivity. The extraction and stripping operations are carried out for the acid mixture by beaker-scale experiments and countercurrent multistage operations with mixer-settler equipment. TOP selectively extracts the acetic and nitric acids in the acid mixture. From the results of the McCabe-Thiele analysis obtained by beaker-scale tests, the extraction for acetic and nitric acids are approximately 100%, respectively, by 6-stage extraction with a phase ratio (A/O) of 0.4. On the other hand, almost all of acetic and nitric acids are stripped with water from the organic phase by 4-stage stripping with a phase ratio (A/O) of 1.0. About 95% of acetic and 98% of nitric acids can be removed from the acid mixture without extracting phosphoric acid in case of the mixer-settler equipment operation. There are several steps such as slicing, lapping, chemical etching and mechanical polishing in the silicon wafer production process. The chemical etching step is necessary to remove any damaged layer caused in the slicing and lapping steps. The typical etching liquor is the acid mixture comprising nitric acid, acetic acid and hydrofluoric acid. The waste acid is treated by a neutralization method with a high alkali cost and balky solid residue. A solvent extraction method is applicable to separate and recover each acid. Acetic acid is first separated from the waste liquor using 2-ethlyhexyl alcohols as an extractant. Then, nitric acid is recovered using TBP (Tri-butyl phosphate). Finally hydrofluoric acid is separated with TBP solvent extraction. The expected recovered acids in this process are 2mol/L acetic acid, 6mol/L nitric acid and 6mol/L hydrofluoric acid. The yields of this process are almost 100% for acetic acid and nitric acid. On the other hand, it is important to recover and reuse the metal values contained in various industrial wastes from a viewpoint of environmental preservation. Most industrial products are made through processes to separate impurities in raw materials, solid and liquid wastes being necessarily discharged as industrial wastes. Chemical methods such as solvent extraction, ion exchange and membrane separation, and physical methods such as heavy media separation, magnetic separation and electrostatic separation are considered as the methods for separation and recovery of the metal values from the wastes. Some examples of the application of solvent extraction to the treatment of wastes such as Ni-Co alloy scrap, Sm-Co alloy scrap, fly ash and flue dust, and liquid wastes such as plating solution, the rinse solution, etching solution and pickling solution are introduced.

Jan 1, 2003

By Roberto Parra

The operational control in a Flash Smelting Furnace is based on the mass and energy balance of the chemical and mineralogical composition of the concentrates. It is well known that many troubles in the dust formation and slag quality occur without a clear correlation to a specific process parameter such as the matte grade or heat balance. This paper outlines two new considerations that could both help improve the entire quality of the process: blend characterization and versatile slag composition control. Related to the blend control, laboratory scale study has shown that the magnetite and dust formation don't have a linear behavior with the weight proportion of the blend and some optimal blends of2 or 3 types of concentrates can be identified. Related to the control of stag composition, the quantification of the slag liquidus temperatures and viscosity could be an effective operational tool for both for ferrite and fayalite slag that can also directly help deciding the blending parameters. From these viewpoints the benefits of the combination of these two approaches for high temperature operation is discussed. Keywords: Optimization, Copper concentrates, Flash combustion, Blends, Slag composition

Jan 1, 2003

By Thomas Niehoff

"Oxyfuel combustion systems are state of the art for many melting operations. Airfuel systems have been stepwise modified to oxygen enrichment, oxygen lancing and oxyfuel. Every change of the melting process will have consequences with regards to emissions and energy usage. The uniqueness of many operations requires unique skills to resolve potential issues. This paper will give some examples of how airfuel systems can successfully be converted to oxyfuel.IntroductionOxyfuel technology – meaning the combustion of fossil fuels such as natural gas, oil or coal with technical oxygen instead of air for industrial melting or heating processes is widely used in many industries these days. Even though oxygen production, storage and handling has been state of the art for decades other opinions exist. Often oxyfuel is regarded with fear and potential hazards like: “Oxygen makes the process too hot.”, “Oxygen will melt away the refractory.”, Liquid oxygen is dangerous.”, “Oxygen will cause explosions.”, ……etc.Typically a more detailed discussion about a specific industrial process and how oxygen can be applied in a safe and economic way the seeming issues go away."

Jan 1, 2010

By Zenjiro Asaki

The copper concentrate particles dissolve quickly into the molten matte in the smelting furnace of Mitsubishi Process, which indicates that the sulfide smelting is essentially a gas/liquid reaction. In this paper, theoretical calculation has been made on the rate of oxidation of FeS component in the matte to form FeO by rising gas bubbles using the penetration theory. The results showed that all the oxygen in the bubble of 1.2 cm in diameter, which is the maximum stable diameter, is consumed in 3 ms. This time required is sufficiently short, and it results in the actual operation of smelting furnace of 1100% oxygen-efficiency. These calculations indicate that most smelting reactions are completed just under the lance, except slag formation.

Jan 1, 2002

By Keith E. Forrester

This paper presents results of bench scale laboratory evaluation of a processes developed by FESI and Brookhaven National Laboratories for the extraction and recovery of Pb and other heavy metals from incinerator ash which was subsequently modified by FESI for the extraction and recovery of Pb from soils excavated from a FESI client scrap yard and battery breaking operation facility. The specific waste matrix presented within the paper is a battery acid contaminated surficial soil at 0" to 12" depth. The extraction method was found to be highly successful on the bench scale in generating a final post-extracted soil matrix which passed TCLP Pb regulatory limits and retained minimal Pb after aggressive extraction application. The paper findings at this time are brief, as a majority of the research results are currently being compiled and additional efforts are underway based upon initial screening findings.

Jan 1, 1995