Search Documents

By C. K. Gupta

Electrometallurgical processes have a definite place in the extraction technology of rare earth metals and alloys. Some of the advantages of the molten-salt electrometallurgical processes include fast electrode reaction, providing accurately controlled large amount of energy to a relatively small reactor volume, negligible over voltage, simplicity of operation, and possibility of accomplishing continuous or semicontinuoue operations. This paper provides a vivid account of the theoretical and practical aspects of electrometallurgical processes for the production and processing of some of the rare earth metals and alloys. Reference has been drawn to the work reported on electrometallurgical processes as applied to the preparation of lanthanum, cerium and misch metal from author's laboratory.

Jan 1, 1992

By Peng Bing

Stainless steelmaking dust is classified as a hazardous waste due to higher than acceptable heavy metal leachabilities such as zinc, lead, cadmium and chromium. In addition to being an environmental hazard, the flue dust is also an economical concern to stainless steelmakers as it contains large amounts of valuable alloying elements, especially for iron, chromium and nickel. A new technology of direct recycling of stainless steelmaking dust has been developed to recover the metals from the dust. But it was found that zinc was accumulated in the dust collection system in practical run of direct recycling. This study focuses on the effect of the operating parameters such as temperature, dust feed rate and the ratio of CO to dust on the reduction of zinc oxides present in the dust. The mathematical model for the reduction process was setup based on the experimental research. According to the mathematical model, the temperature has obvious effect on the reduction of zinc. It is benefit to the process of zinc reduction to increase the temperature. But the temperature will not be the main factor for the reduction process after 1228C. It will promote zinc reduction to decrease the dust feed rate and control the ratio of dust to CO. It was also found from the experiments that ZnFe2O4 in the dust could be decomposed at high temperature. Decomposing ZnFe2O4 in the dust increases the recovery of zinc from the dust distinctly.

Jan 1, 2006

By Esher Hsu

On July 5, 1997, Environmental Protection Administration of Taiwan publicized the recycling regulation of waste home appliances that include four items, namely, television, refrigerator, washing machine, and air conditioner. It is believed that this regulation pioneers the law enforcement of waste home appliances in the world. The objective of this study is to provide helpful base for amending recycling rates of waste home appliances. This study investigates the collection and recycling costs of waste home appliances in accordance with these newly established routes and facilities, respectively. Cost survey was conducted among collectors and recycling plants of waste home appliances; consequently, the collection and recycling costs were analyzed, correspondingly. Results provide some suggestions regarding recycling route, recycling system, recycling rates paid by manufactures and importers, recycling subsidies to collectors and recyclers. Those suggestions may provide useful policy implications to EPA for the future decision-making regarding the recycling of waste home appliances.

Jan 1, 2003

By Karl A. Gschneidner

The magnetocaloric effect has been known for 120 years and has been utilized for cooling about 70 years. But in the last four years significant advances have been made to show that magnetic refrigeration is a viable and competitive cooling technology. Most of the work has focused on reciprocating devices, but rotary apparati are being developed. To date the magnetocaloric properties have been characterized for more than 200 materials. The magnetocaloric effect behaviors have been classified into three types of behaviors. The most common one is found in magnetic materials which exhibit a second order magnetic phase transition. Magnetic materials which exhibit a first order magnetic phase transition account for the second group of materials. Materials which exhibit multi-magnetic phase transitions make up the third group. The best candidate materials for magnetic cooling over the range from -4 to -1 350 K are also presented.

Jan 1, 2002

By Guozhu Ye

"One of the most essential problems associated with the treatment of EAF dust is its high content of halogens. For most thermal processes for zinc recovery, such as the plasma processes with a zinc condenser, the halides in the gas stream will form a dross phase that results in a low zinc yield. For those with zinc oxide as main product, such as Waelz oxides, the high halogen content in the product implies a great degradation of the product quality and the product can only be sold at a low price. Further processing of zinc oxide with high halogen content either by pyrometallurgical or hydrometallurgical processes will also result in process problems.This paper will review the pre- and post-treatment alternatives for halogen removal based on the comprehensive characterization work that has been carried out at MEFOS and the preliminary experimental results.The experimental results show that chlorine and fluorine content could be reduced to 450 ppm and 50 ppm respectively by selective sulfation, and to about 200 ppm by soda leaching. Selective sulfation of zinc oxide in the EAF dust will also be discussed."

Jan 1, 2000

By Fumito Tanaka

In the Mitsubishi Continuous Copper Smelting & Converting Process, the heat for the dissolution of scraps is effectively supplied from the melts strongly stirred by top injection. Various kinds of shape of scraps not only powder but also lump, sheet, cube and so on can be treated without any emission of dust and fugitive gas, and no additional furnaces for scrap processing is necessary. Therefore, this process is much suitable for recycling. The authors have investigated the melting rate of ice sphere into a water bath equipped with top blowing lances as a basic study for the dissolution of scrap. Hydrodynamic experiments were carried out, and mathematical models were applied to the results. The results show that the melting rate of ice sphere strongly depends on the standing waves at the bath surface.

Jan 1, 2001

By Chikabumi Yamauchi, Mitsuru Tanahashi, Jutaro Miura, Takaharu Iwadachi, Toshiharu Fujisawa

"Tue oxidation behavior of molten Cu-Be alloys was investigated by exposing· the molten Cu-Be alloys to various Ar-O2 atmospheres to control the oxygen partial pressure, PO2 = 10 ~105 Pa at 1423 K. The following results were obtained:• The oxygen · partial pressure in gas phase affects the morphology of the oxide formed on the surface of the alloy and · the oxidation rate of beryllium.• At lower oxygen partial pressure, a molten Cu-Be alloy is covered with a homogeneous and compact internal layer of BeO. Thus, the beryllium oxidation rate can be minimized.• By adding a small amount of calcium or zirconium into the molten Cu-0.5 mass% Be alloy, a protective BeO layer is formed even at higher oxygen partial pressure. Thus, the beryllium oxidation rate can be reduced.IntroductionCopper-beryllium (Cu-Be) alloys are well recognized for their unique properties, such as high electrical conductivity, high strength, high fatigue strength, excellent properties at elevated temperatures, good formability and good corrosion resistance. .This extraordinary collection of properties are the reasons why Cu-Be alloys are expected to be ""Key-materials"", which are necessary to further advance science and technology and to be applied in.various fields such as electronic devices, machine parts, repeater housings of undersea optical fiber communication cables, etc.However, a large amount of beryllium is oxidized to BeO in melting stage of the current Cu-Be alloy production process, because beryllium is a highly reactive element. This is one of the ·main factors that negatively affect the production yield and th_e product quality."

Jan 1, 2000

By Matthew Jeffrey

Leaching, cementation, electroplating and flotation are all electrochemical phenomenon. They are also key processes in the hydrometallurgical treatment of metals. Unfortunately electrochemical methods tend to be under-utilized when studying these processes and one possible reason for this is the confusion surrounding the large number of electrochemical techniques available. In this paper four former PhD students of Professor Ian Ritchie present an insight into how one electrochemical technique can be used to compliment rate/kinetic studies. The paper details how to perform the experiments, interpret data, and recognize complications with the results. Examples where this approach has been highly successful are presented, and include: cementation of zinc by aluminium, cementation of copper by nickel, cyanide leaching of gold and the cementation of gold thiourea by mild steel. The examples illustrate that this universal approach adopted by Ian Ritchie provides the key to understanding the mechanism of many hydrometallurgical reactions.

Jan 1, 2003

By Guray Kaya

Boron minerals are widely employed in various fields such as ceramic, glass, cement, metallurgy, etc. Although boron deposits of the world are limited, the production level of boron-based products is continuously increased. Turkiye possesses approximately 73 % of total world boron resources. Etibor Kirka Borax Company of Turkiye produces tincal concentrates and borax pentahydrates. During such productions considerable amounts of concentration and derivation wastes appear. Having considered the increased rate of production it is quite obvious that the level of relevant wastes will also be raised. With this study it was aimed to utilize these wastes in roof tile and brick bodies and to convert them into a form environmentally and human friendly. Newly produced products were undergone to several standard tests for the determination of their shrinkage, water absorption, strength values and coloring parameters. Additionally, micro structural studies were conducted.

Jan 1, 2006

By G. Brooks, J. Naser, M. A. Sattar

CFD models have been developed and numerical simulations have been carried out to predict the formation of foam in oxygen steelmaking. Foam was considered as a separate phase comprising a mixture of gas and liquid. Bubble break up and coalescence models have also been incorporated in a CFD model to predict the number density of individual bubble classes. A population balance equation was used to track the number density of each bubble class. Decarburization with heat generation from chemical reactions was integrated in the process. User subroutines were written in FORTRAN to incorporate the foam formation, the bubble break up and coalescence rate and decarburisation in the main program. The model predicted the foam height, bubble number density, velocity of phases, decarburization, and turbulence. The result from the model has been compared with available data from literature and found to be in reasonable agreement with the experimental and plant data.

Jan 1, 2014

By A. D. Neuman, C. C. Davis, M. R. Lopez, A. C. Martinez, T. A. Nothwang, S. L. Voit

"One of the thrust areas for the Global Nuclear Energy Partnership (GNEP) program is the development of actinide bearing fuels for transmutation in a fast reactor. Mixed Oxide (MOX) fuel has an extensive fast reactor irradiation history and thus is being considered for use as a baseline composition from which minor actinides (MA) can be incorporated for use as a transmutation fuel. This study involves characterization of precursor powders and pellets to be inserted into the Advanced Test Reactor in Idaho. These pellets will have three compositions: one standard MOX composition, (U80Pu20)O1.98, and two compositions of MA-MOX with oxygen to metal ratios (O/M) of (U75Pu20Am3Np2)O1.98 and (U75Pu20Am3Np2)O1.95. The precursor powders, which consisted of, highly enriched uranium oxide, HEUO2, depleted uranium oxide, DUO2, neptunium oxide, NpO2, americium oxide, AmO2, and plutonium oxide, PuO2, were characterized using a field emission gun scanning electron microscope (FEG-SEM) for particle morphology, size, and size distribution prior to pellet production.IntroductionThe Global Nuclear Energy Partnership (GNEP) was created in order for “fuel-cycle supplier” nations to provide assured supplies of nuclear fuel to “fuel-cycle customer” nations. The customer nations would utilize the fuel for electricity generation and subsequently return it to the supplier nation after it is spent. This spent fuel would then be reprocessed by the supplier nation in order to recycle the actinide constituents, mainly uranium and plutonium, in advanced nuclear power reactors, and thus reducing waste volumes [1, 2]. Nuclear materials would also be strictly controlled through the International Atomic Energy Agency. One of the thrust areas for the GNEP program is the development of these actinide bearing fuels for transmutation in a fast reactor under the U.S. Advanced Fuel Cycle Initiative (AFCI) in order to transmute long-lived transuranic actinide isotopes into shorter-lived fission products [3]."

Jan 1, 2008

By Maria D. Salazar-Villalpando, Anthony Cugini, Bryan Reyes

"The electrochemical reduction of CO2 was performed in a laboratory-made, divided Htype cell. A copper electrode was used as the cathode. An Aldrich Nafion 117-type ion exchange membrane (0.18mm thickness) was used as the diaphragm. NaHCO3 and KHCO3 were studied as the catholytes. Hydrogen evolution from water reduction and products from CO2 electrochemical conversion were recorded. Higher CO2 reduction enhancement was observed by KHCO3 as compared to NaHCO3. The main conclusion of this work is that in fact CO2 can be electrochemically reduced with copper electrodes.1.-INTRODUCTIONThe direct electrochemical reduction of CO2 may allow for a simple process and, by avoiding high temperature reactors, would enable the process production rate to be quickly varied to follow the time of day availability of surplus electricity [1]. Temperature has a major effect on the electrochemical conversion of CO2 since its solubility increases when temperature decreases [2]. The electrical potential applied to the electrochemical reacting system will have an influence on the product distribution, as well. For example, a narrow potential range during cyclo-voltagraphic studies will determine the detection of a lower number of products. A recommended potential range to study the electrochemical reduction of CO2 is -2V to 2V. Moreover, the reaction rate on the electrode is governed by various processes, such as the kinetics of electron transfer, adsorption/desorption at the electrode surface, and diffusion of CO2 to the Cu electrode. The availability of active species, CO2 for electro-reduction, is extremely low at the vicinity of the electrode surface and it seriously interferes with the rate of mass transfer. In batch type electrolytic reactors, depletion of CO2 at the surface takes place first. CO2 from the bulk then has to diffuse to the electrode surface, resulting in mass transfer controlled kinetic phenomena. During the above process, several other competitive side reactions could suppress the primary reaction even though the cathode has good electro catalytic properties for reduction of carbon dioxide. When the dynamic supply of specific active species is ensured to electrode surface, the mass transfer effects are minimized to certain extent. Hence it is envisaged that a continuous flow reactor is more efficient for the electro-reduction of CO2 in CO2 saturated aqueous electrolytes. The primary reactions that occur at the copper electrode during the reduction of CO2 are listed below (with the standard potentials calculated using formation energies [1] :"

Jan 1, 2010

By B. Q. Li, S. P. Song

"Numerical models are developed to represent complex electromagnetic, free surface deformation and fluid flow phenomena in floating zone refining processes with radio frequency inductive heating. The computational methodology is based on the coupled finite/boundary element method for the electromagnetic field distribution and the Galerkin finite element method for magnetically driven fluid flow and free surface profiles of the molten zone. With the models, the complex transport and free surface phenomena in a floating zone system can be studied as a function of various operating conditions including applied current, frequency, inductor position and shape, surface tension, floating zone diameter and height. Results show that the equilibrium shape is sensitive to the height of the molten zone and that the free surface shapes can have a significant effect on the melt flow in the molten zone. Our extensive simulations also suggest that to ensure accurate results, the same mesh should be used, whenever possible, for both the electromagnetic forces and fluid flow calculations.1. IntroductionThe floating zone processes have been widely used in the materials industry to grow ultra-pure rare earth metal or semiconductor single crystals for sensor or electronic applications that have a tough demand on purity. Developed based on the principle of magnetic melting/levitation, the processes possess a main advantage that the molten zone is supported in air by the electromagnetic forces generated by the coil (see Figure 1), and therefore is free from contamination from a container. Consequently, the final products made from the floating zone processes have higher inherent purity than those by other techniques [1-4].Complex physical phenomena occur in the floating zone processing of materials. These include free surface deformation, magnetically-driven melt flow, which may be turbulent or mildly turbulent [5] depending on the applied conditions, and solidification. Thermal stresses also develop in the single crystals, which are affected by the flow and temperature field and which can have direct implications to qualities of single crystals [6]. An understanding of the fundamentals governing these physical phenomena can be of critical value in elucidating the physics that controls the properties of the metal or semiconductor crystals being produced, thereby providing a rational basis for process improvement and quality control."

Jan 1, 1997

By E. S. Geskin

New material processing tools should be developed and reduced to the practice in order to meet the challenges facing the contemporary material production industry, One of such potentially important tools is supersonic liquid projectiles. It was shown that at the speed of 1500-1750 m/s the water projectile are able to demolish reinforced concrete plates, forge, to pierce and weld metals, to destroy with no explosion non dischargeable mines, etc. These projectiles are generated by simple, low cost launchers run. It is obvious that these projectiles can be applied to the ore mining and comminution. Thermodynamic considerations show feasibility of the use of these projectiles also for smelting, refining and forming. The presented paper discusses the results of the experimental study of supersonic liquid projectiles as well their potential metallurgical applications.

Jan 1, 2006

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

By Ligang Zhang, Wen Chen, Xinghua Liu, Jialin Li, Xiaoyin Liu, Zhenhong Liao

A research-scale fluidization and magnetization roasting device was developed to evaluate a processing option that might offset the complexity and high cost of the conventional magnetization roasting process on siderite. In this study, the operating parameters of the fluidization and magnetization roasting device for siderite were evaluated through cold-flow tests and magnetization roasting tests. The reaction mechanism functions of the fluidized roasting process are revealed with kinetic studies.

Jan 1, 2015

By D. D. Harbuck

The U.S. Bureau of Mines recently identified a significant new source of scandium in an Oklahoma tantalum waste residue (approximately 0.24 pct Sc). Because scandium is a strategic and critical metal which the Department of Defense has classified for special consideration, the Bureau is researching methods of recovering scandium and associated metals from this and other process residues. A variety of operating parameters were evaluated to determine the best technique for recovering scandium. Testing showed that by sulfating the residue at temperatures as low as 150' C for reaction times as short as 0.5 hr, over 94 pct of the scandium converted to a water soluble form. Solvent extraction using DEHPA selectively recovered 100 pct of the scandium from the water leach solution.

Jan 1, 1992

By W. Mueller

The function of a process mineralogist in the operation of a copper mine and plant is to assist in the identification and classification of the operation's main throughput. These include ore, concentrates, slag and matte, and to a lesser extent, refined products. In addition, a number of other products not normally thought of in association with mineralogy are examined. These include scales from submersible pumps, failed boiler tubes, acid plant, and shaft furnace; characterization of inclusions in failed compressor gear teeth as well as in copper rod; and flue dusts from a smelter, air transported particulates and coatings on passive copper anodes in the refinery. Techniques and equipment required for these studies include simple hand magnets to the high intensity Isodynamic separator, visual examination to electron microscopes, x-ray equipment, DTA, IR, heavy liquid separation, and contracted services of custom laboratories. Several examined products from Magma Copper Company have been selected to illustrate the range of techniques and equipment required by a process mineralogist.

Jan 1, 1981

By A. MacRae

Campaign life of the converting furnace has been limited by break-outs through the hearth and walls. Throughput of concentrate has increased by 60% since start-up of the copper operations in 1981. The Furnace Integrity program was initiated at Kidd in 1993 to improve the reliability and safety of the smelting-cleaning-converting furnace line. The converting furnace is undergoing a series of upgrades to overcome severe refractory wear to the roof, walls and hearth. A recent shut-down was held in March 1997 to implement improvements to the roof, walls and slag outlet. Wall modifications included a new upper shell, wall coolers which can be supported during a shut-down from outside of the vessel, and an increase in the number of cooling blocks. Improvements to the roof included increased cooling, a novel brick/cooler suspension system, and roof compression for gas tightness. Design is currently underway to deepen the refractory hearth, to decrease hearth erosion and increase resistance to flotation.

Jan 1, 1998

By E. B. Freidina

We have investigated a new electrochemical process for preparing lead-calcium alloys. Calcium metal, reduced fiom a molten chloride mixture, forms an alloy with liquid lead cathode. The addition of calcium carbonate to conventional CaC12-NaCl electrolyte enables us to avoid chlorine production on the anode and replace it with oxygen and carbon dioxide. The ternary system CaClz-NaC1-CaCO3 has a range of melt compositions, where the electrolysis can be held below 650°C. In order to prevent the side reaction of carbon deposition on the cathode we have separated the anolyte from the catholyte with alumina diaphragm. The factors, which affect the level of impurities and the current efficiency of the process, are discussed.

Jan 1, 1999