Search Documents

By W. A. Cincilla

The use of resin-grouted rock anchors continues to gain popularity in underground wall mines in the United States. It is estimated that during 1985, more than 30% and as many as 35% of all roof bolts used employed sane from of resin anchor. The so-called 'combination' bolting systems, which generally utilize a resin pint-anchor, have also found increased application. This increased application is particularly true in poor ground, where more 'traditional' support measures have performed poorly. Virtually all resin bolts in use today in U.S. mines employ cartridge-type delivery systems, which in general, have produced good results under a variety of conditions. However, a host of inconsistent and sometimes uncontrollable variables may significantly alter the optimum bolt performance. These variables have been identified and are well documented in the literature (Snyder, et al., 1979; Kwitoweki and Wade, 1980; Serbcusek and Signer, 1985). The beau of Mines, Denver Research Center (DRC) conducted a major research project aimed at investigating the effects of selected aspects of installation procedures on resin-bolt performance. One objective of the project was to establish anchorage criteria for full column resin bolts installed in actual mining conditions. This piper describes the results of a particular study which focused on quantifying, through field tests, possible reductions in bolt anchorage due to installation of less-than optimum resin columns. These columns might result from losses of resin to surrounding strata, or non-compliance with recommended installation procedures. Over 1000 resin bolts having grout columns ranging from 12 inches up to 48 inches (full column) were installed and pull-tested at 13 underground test sites located in a total of 11 mines (Fig. 1). Four basic roof-rock types were included: shale, top coal, sandstone, and limestone. The majority of the bolts employed 3/4-in-diameter, 48-in-long, type 40 rebar having a minimum '~ated' yield point of 17,600 lb (8.8 tons). Actual yield strength may vary by manufacturer.

Jan 1, 1986

By Paul C. Hagan, Jianhang Chen, Serkan Saydam

"Modified cable bolts are commonly used in underground mines due to their superior performance in preventing bed separation when compared with plain strands. To better test the axial performance of a wide range of cable bolts, a new Laboratory Short Encapsulation Pull Test (LSEPT) facility was developed. The facility simulates the interaction between cable bolts and surrounding rock mass, using artificial rock cylinders with a diameter of 300 mm in which the cable bolt is grouted. Furthermore, the joint where the load is applied is left unconstrained to allow shear slippage at the cable/grout or grout/ rock interface. Based on this apparatus, a series of pull tests were undertaken using the MW9 modified bulb cable bolt. Various parameters including embedment length, test material strength and borehole size were evaluated. It was found that within a limited range of 360 mm, there is a linear relationship between the maximum bearing capacity of the cable bolt and embedment length. Beyond 360 mm, the peak capacity continues to rise but with a much lower slope. When the MW9 cable bolt was grouted in a weak test material, failure always took place along the grout/ rock interface. Interestingly, increasing the borehole diameter from 42 mm to 52 mm in weak test material altered the failure mode from grout/rock interface to cable/grout interface and improved the performance in terms of both peak and residual capacity.INTRODUCTIONFully grouted cable bolts have been used in underground mining industry for many decades. Initially, plain cable bolts manufactured by winding seven flexible steel wires together were commonly used (Thorne and Muller, 1964). Laboratory and field tests lead to a better understanding of the transfer process between grouted cable bolts and the surrounding rock mass, which is beneficial to improve the reinforcing performance of cable bolts in engineering practice (Fuller and Cox, 1975; Cox and Fuller, 1977; Schmuck, 1979; Stillborg, 1984). Nevertheless, as in many cases the initial cable was sourced from discarded steel with a smooth surface along the strand, plain cable bolts did not always meet performance expectations (Windsor, 1992). Over time, it was realised that cable surface geometry plays an important role in determining anchorage performance. Consequently, modified forms of cable bolts were developed. For instance, twin-strands which were made by using spacers to combine two plain cables together improved anchorage capacity two-fold (Matthews, Tillmann and Worotnicki, 1983). However, this required a large borehole to be drilled. Epoxycoated strands had remarkable performance in practice but were difficult to install without damaging the epoxy layer (Dorsten, Hunt and Kent, 1984). In the 1990s, there was a rapid development in the cable bolt design. A typical example was birdcaged cable bolts. They were initially suggested by Hutchins et al. (1990) via unwrapping traditional seven-wire strands and generating a number of nodes together with antinodes along the strand. But it was difficult to make birdcaged cable bolts that could be coiled for transporting."

Jan 1, 2015

By Zach Agioutantis, Christopher Mark

"Thirty years ago, the Analysis of Longwall Pillar Stability (ALPS) inaugurated a new era in coal pillar design. ALPS was the first empirical pillar design technique to consider the abutment loads that arise from full extraction, and the first to be calibrated using an extensive database of mining case histories. ALPS was followed by the Analysis of Retreat Mining Stability (ARMPS) and the Analysis of Multiple Seam Stability (AMSS). These methods incorporated other innovations, including the Coal Mine Roof Rating (CMRR), the Mark-Bieniawski pillar strength formula, and the pressure arch loading model. They also built upon ever larger case history databases and employed more sophisticated statistical methods.Today, these empirical methods are used in nearly every underground coal mine in the US. However, the piecemeal manner in which these methods have evolved resulted in some weaknesses. For example, in certain situations, it may not be obvious which program is the best to use. Other times the results from the different programs are not entirely consistent with each other. The programs have also not been updated for several years, and some changes were necessary to keep pace with new developments in mining practice.The Analysis of Coal Pillar Stability (ACPS) now integrates all three of the older software packages into a single pillar design framework. ACPS also incorporates the latest research findings in the field of pillar design, including an expanded multiple seam case history data base and a new method to evaluate room and pillar panels containing multiple rows of pillars left in place during pillar recovery. ACPS also includes updated guidance and warnings for users and features upgraded help files and graphics.INTRODUCTIONPillar design is one of the fundamental elements of mining engineering. Pillars are necessary to control the great weight of the overburden during all phases of underground mining. Without stable pillars, ground control is impossible."

Jan 1, 2018

By Zuoliang Xiu

Experience indicates that rockbolting is the most efficient and cost effective means of supporting gateroads of retreating longwalls. However, gateroads supported solely by rockboltiug currently accounts for less than 16% of the 4500km of annual gatemad drivage in China According to a stated target of the Ministry of Coal Industry, this percentage should be at least 50% by the year 2000. Since the learning stage of the technology which is indicated by low drivage rates and frequent roof falls in rockbolted gateroads must be overcome , strategies for the application of rockbolting to gateroads have become the focus of discussions on this topic. This pap presents the recent development on longwall gateroad rockbolting technology in China The development work has concentrated on understanding the mechanism of rockbolting; establishing new design procedures of bolting parameters fix gateroad support upgrading the consumable; optimizing bolt installation procedures; adopting better roofbolting machines; and developing adequate secondary reinforcement technique. The authors believe that this development work together with the on-going wok in other aspects of gaterosd rockbolting, as discussed in this paper 9 represent the rational strategies for the application of rockbolting technology to a wider range of longwall gateroads in Chinese d mines .

Jan 1, 1997

By Ismet Canbulat, John Naylor, Jason Emery, Peter Craig, Andy Sykes

"Longwall mining is by far the most common method of underground coal extraction in Australia. The industry trends and expectations are placing increasing emphasis on the reliability and productivity of these operations. The longwalls are becoming wider and longer while retreat rates are continuously increasing due to significant improvements achieved in longwall equipment reliability and automation. This increased longwall productivity is placing significant emphasis on the reliability of longwall panel development.Although there have been significant improvements in the reliability of continuous miners and hydraulic drill rigs, the traditional resin encapsulated bolt installation is still the principal method used in all major coal-producing countries around the world. Anglo American realised an opportunity existed to introduce an alternative roof bolt installation technique called “spin to stall” in Australia. Spin to stall was first introduced in Anglo American Coal in South Africa where it has been successfully used for over a decade, though implementation of South African spin to stall resin in Australia has proven to be near impossible due to a significant difference in geotechnical conditions, mining method, and, subsequently, roof bolting equipment. Therefore, a new spin to stall development project was initiated between Anglo American Coal and Jennmar Australia (SPIN2STALL®). This paper summarises the journey of this project, the results, and the successful implementation of spin to stall achieved at Grasstree Mine.INTRODUCTIONThe Anglo American Coal business unit operates Grasstree and Moranbah North underground longwall mines in the Bowen Basin of Central Queensland, with a third longwall mine, Grosvenor, currently being developed, and two more (Aquila and Moranbah South) in the project pipeline. The vision for Anglo American is to achieve “Zero Harm” through the effective management of safety at all operations, while for the coal business unit, at the same time to achieve industry-leading operational performance. Currently, both Grasstree and Moranbah North longwalls are operating at industry best practice rates. This is placing increased pressure on the development process to allow such high productivity levels to be sustainable."

Jan 1, 2015

By J. K. Owens

As part of a larger research effort focused on ground control, the U.S. Bureau of Mines is currently evaluating the effectiveness of using stereological analysis for characterizing mine roof strata. Input for a stereological analysis of a rock mass is best obtained by scanning (imaging) the walls of clean drill holes using a video-imaging borescope or other video device. Two classes of features are being investigated: (1) Lithologic types that comprise the overall rock mass and (2) structural discontinuities (e.g., joints, foliation, bedding planes) within a given lithologic unit. In the former, the volume fraction of a given Lithologic unit in relation to the entire rock mass can be estimated. In the latter, the mean intercept length between adjacent structures and surface area density of the geologic structures can be estimated. Examples of sampling procedures and subsequent computations are presented for several situations using information collected from drill holes in roofs of underground mines. One such example is based on the trace of a cycloid curve used as a stereological sampling path on the cylindrical wall of a drill hole. Stereological measures, such as intercept length, volume fraction, and surface area density, are explained in the context of rock mass characterization.

Jan 1, 1994

By Dale S. Preece

In 1975 Congress passed the Energy Conservation Act to establish a U. S. Strategic Petroleum Reserve (SPR) with a capacity of 750 million barrels of crude oil. The most economic storage medium was determined to be salt caverns leached in salt domes in Louisiana and Texas. Salt caverns existed at several sites when the reserve was created. These were obtained by the U. S. Department of Energy (DOE) and used to initiate SPR oil storage. In order to meet the storage capacity approved by Congress, new caverns also had to be leached. To support the resulting design effort, finite element computer program have been used to determine the creep closure and structural stability of salt caverns. Using site specific material properties including creep models, elastic moduli and fracture data, the finite element analyses have replaced earlier empirical approaches to cavern design. This report presents results of such finite element analyses to determine the best cavern roof shape and the minium pillar to dimeter ratio. , P/D. These numerical predictions indicate that the current cavern design is safe.

Jan 1, 1984

By John K. Wood

The development of an expanded cement product represents a major advance in the technology of roof control systems. Such a product is gaining recognition as a valuable tool in today's cost- conscious coal mines. The National Coal Board's Bretby Research Lab, in conjunction with Polement Ltd., developed the first lightweight cement for use in the mines of the United Kingdom. The product, Aqualight, is a low-density (about 12.5 PCF) cement with a typical compressive strength of about 19 p.s.i. The final product increases in volume by approximately 15 times its dry powder volume. Aqualight gels in about 2 minutes, becomes self-supporting in 15 minutes, and fully cur& in 24 hours. When subjected to a load, the "cells" within its bubble structure collapse so that the product gains in density and compressive strength while retaining its integrity. Traditional methods to contain and support roof fall cavities through cribbing and blocking are both dangerous and labor-intensive. Aqualight represents a significant advantage over such traditional methods. It is non-toxic, non-cmbustible, and very easy to install. Aqualight can be pumped to the worksite from re- mote locations (as much as 600 feet), thereby reducing danger to men and equipment. Addition- ally, the strength of the cured product can be varied by adjusting the expansion ratio and resulting density. A compressive strength of 150 p.s.i. can be obtained in this manner. Although primarily designed to fill cavities resulting from roof falls. Aqualight has found a wide range of applications in mining industries around the world. In addition to cavity- filling, Aqualight has been used for ventilation stoppings, fire stoppings and emergency fire control, backfilling between arches and the roof and ribs, and backfilling of old workings. Since its recent introduction into the United States. Aqualight has been used by MICON SER- VICES, INC. to fill several roof fall cavities along headgate entries. In all cases, the cavities were contained and the longwall moved through without problems. Roof Pall cavities along main haulage entries and at shaft/slope bottoms have been successfully filled. MICON has also installed Aqualight as backfill material around arches. A current major project is the installation of trial ventilation seals using Aqualight as an alternative to traditional block and mortar construction. Pending MSHA approval, MICON anticipates the use of Aqualight in the construction of both ventilation seals and stoppings. In addition to new construction, Aqualight can be employed to repair stoppings damaged by roof convergence and floor heave. In labor savings alone, this is very attractive for remote stopping repair. Among the many other uses of Aqualight is the backfilling of old auger holes, which will support the highwall and allow access to coal re- serves which are presently sterilized.

Jan 1, 1986

By Gerald I. Finfinger

Identifying the properties of overlying rocks in underground mining operations is important to ensure the appropriate roof support design is used to maintain stability of the mine entries. Recently J. H. Fletcher & Co. developed a monitoring and control system for roof bolters for the underground mining industry. The system records the drilling parameters used during roof bolt drilling and the information can provide insight into the physical properties of the roof strata. The parameters include thrust, rotational speed, torque and velocity and the measurements are collected every 0.1 second during the operation. The drilling parameters were analyzed to determine the application of identifying the strength of rocks being drilled from the measurements. The data was converted into the specific energy of drilling which is a measure of the amount of energy required for removing a given unit of rock during a drilling operation. The laboratory studies completed to date indicate a fairly high correlation between the specific energy of drilling and the unconfined compressive strength of the rocks that were drilled. Additionally, the drilling parameters were shown to be effective for identifying the presence of fractures or bed separations between rock ]avers. The thrust, torque and specific energy of drilling were all good indicators for identifying the fractures or separations. Regardless of the drilling parameters used during the drilling experiments, the location of the fractures were identified, In order to determine the application of the drilling parameters for identifying rout rock properties, two series of experiments were conducted. The first series of experiments used three "manufactured" roof layers that had various rock samples embedded in concrete blocks. The rock samples included three types of sandstone, marble. and argillite. Another concrete block was poured with foam inserts to simulate large bedding separations (2 to 8-in). Two other manufactured blocks were constructed using high-strength concrete with cardboard layers embedded to simulate smaller fractures or bedding separations. The size of the cardboard layers varied from 1/8- to 1-in thick. One of the blocks had the cardboard layers embedded at an inclined angle to determine the effect of the orientation or, the drilling parameters. A series of experiments was conducted with the rotational speed and the penetration rate held constant and the thrust and torque allowed to vary. The information collected from the experiments is used to determine the application of the drilling parameter measurements for identifying rock properties, fractures and bedding separations.

Jan 1, 2000

By Gennaro G. Marino

Site conditions at several shallow room and pillar mines in Illinois are described and compared with the charac¬teristics of the subsidence profiles at the ground surface. The shape and magnitude of the subsidence profiles were found to be closely related to the thickness of the soil and rock over-burden the percent extraction of the coal, and the shape of mine pillars. The room and pillar mines were located at a shallow depth (from 112 to 220 ft), beneath flat to gently rolling terrain. Thickness of the coal seams ranged from 5 to 9 ft and at all sites was underlain by underclays. This information has been developed in order to improve techniques for evaluating the subsidence potential at sites within the Illinois coal basin. he results presented form a small portion of the work carried out by the University of Illinois with Illinois Abandoned Mined Lands Councils and the U. S. Bureau of Mines at the Minneapolis Research Center in Minnesota (Marino and Mahar, 1985). Presented in the paper are the modes of mine failures observed for Illinois room and pillar mines, an overall summary of the site geologic and mining condi¬tions, case histories of each mode of failure, a comparison of sag profiles, and then an empirical relationship between the site conditions and the maximum sag subsidence. The most ideal case histories are presented to illustrate fundamental behavior. A brief of the Paper is given in a summary and conclusions section.

Jan 1, 1984

By Jian Yong Chen

The results of a laboratory investigation of pullout tests conducted on grouted, plain cable bolts are reported. The main purpose of the study is to determine experimentally the shear bond stiffiess of cement grouted and resin grouted cable bolt systems, which is an important input parameter for numerical modeling of cable bolt support. Three nominal embedment lengths of 152mm (6 inch), 203mm (8 inch) and 254mm (10 inch) were used and two types of grout namely cement and Anchortite resin were used. Two water- to-cement ratios of 0.3 and 0.4 were employed for the cement grout. The concepts of effective shear stress and effective shear stiffiess are explained and adopted to calculate the shear bond strength and the elastic shear bond stiffiess per unit length. A comparison of results with previous research is presented to reveal the effect of water-to-cement ratio and embedment length on the shear bond characteristics of grouted cable bolts.

Jan 1, 2005

By Michael J. Friedel

The fundamental problems associated with ground control reflect the inability of mining personnel to "see" the development of anomalous conditions. Toward this end, the U. S. Bureau of Mines is investigating the application of seismic refraction tomography for imaging the process of pillar yielding, at the Foidel Creek coal mine, near Steamboat Springs, CO. The inherent three-dimensional problem of imaging coal pillar stress is reduced to a single plane by considering only the stress transmitted from the pillar to the adjacent floor rock. This approach exploits the fact that refracted seismic energy is essentially confined to the adjacent higher velocity sandstone strata. The tomographic analysis using ray-tracing based on wavefront migration resulted in a robust P-wave tomogram from which regions of high velocity indicate zones of high stress concentration, whereas low velocity zones indicate regions of stress relief. The interpreted region of high stress concentration occurs at the pillar end nearest to the working face of the adjacent longwall panel. This finding is corroborated by vertical pressure cell measurements recorded in the pillar. The stress diminishes toward the pillar perimeter with local minima correlating to the locations of observed pillar spalling. Time-sequence monitoring, as the longwall face advances, is recommended for evaluating changing stress conditions.

Jan 1, 1993

By I. Geldmacher

In-Seam Seismic (ISS) methods have been used extensively worldwide for the past 10 years to assist mine planning, espe¬cially longwall mining in coal seams. The technique is only starting to gain wide acceptance in North America where it is being applied in a much wider variety of applications than was initially considered. Surveys elsewhere have concentrated on the detection of faults (structures) in coal mines prior to longwall mining. The majority of surveys in North America has been the location of abandoned workings which were not adequately surveyed prior to closure. Modeling data based upon the lithological logs, geophysical logs and interpreted sections show whether the method will be successful prior to carrying out the survey. The surveys have been performed to locate abandoned wor¬kings from the surface and underground using both seismic reflection and transmission techniques. Data from coal seams in both Illinois and West Virginia will be presented. A second method where ISS surveys are being applied to detect old workings will be presented. The ISS tomography produces an image of the P-wave and Channel Wave velocities which is representative of the material through which the signal traveled thus identifying the location of the old workings. Data from Texas will serve as an example.

Jan 1, 1990

By Maynard O. Serbousek

The mechanics of load transfer of fully-grouted roof bolts in coal mines has been investigated in laboratory and analytical studies. The purpose of this research is to increase the understanding and better interpret data from pull tests which are routinely performed in the field. Laboratory work includes variation of bolt length, hole diameter and grout type in pull tests. Four-foot bolts were tested in holes of 1- and 1-3/8-inch diameters. Both polyester resins and inorganic grouts were used as the anchorage medium. The bolts were strain gauged at six locations to observe the rate of load transfer from the bolt to the rock mass when a force was applied at the bolt end using standard Jack pull testing procedures and equipment. Analytical studies using closed form solutions and finite-element techniques were compared to experimental results. The models are for the elastic regime only but do include slip elements. A detailed analysis of the load transfer mechanisms from the bolts through the grout to the rock mass is presented.

Jan 1, 1984

By Phillip E. Gramlich

Through extensive practical experience and multiple studies, tensioned roof control systems have proven beneficial in difficult mining conditions. Due to increased mining of less desirable seams, tensioned roof control systems have claimed a progressively larger share of the total number of roof bolts installed in the US coal industry. Each tensioned roof control system has its benefits, but also has problems concerning cost, cycle time, stress concentration, load retention, and protrusion into the mine opening. For example, resin-assisted mechanically anchored bolts (also known as resin point anchor bolts) have a fast cycle time and the potential for high tension loading, but the stress from the mechanical shell is concentrated in a small area and can create concerns with certain roof structures (Zhang and Peng, 2001). Resin point anchor bolts can be difficult to fully grout. The cost of resin point anchor bolts can be an issue; a two-piece resin point anchor bolt has a large number of parts (10) and manufacturing steps (9), adding to its higher cost. Tension rebar bolts can achieve high loads and are easier to fully grout but have longer cycle times. In addition, a high percentage of the installed load can ?bleed off? if the resin mixing time or the ?hold time? before tensioning is short-circuited. Tension rebar bolts can be notorious for protruding into the mine opening, creating an obstruction for man and machine (Figure 1), in particular, with reduced mining heights. A new tensioned roof control system has been developed that doesn?t have moving parts, is cost effective, provides fast cycle times, has a low profile, and is simple t install.

Jan 1, 2014

By Sean C. Farrell

In underground mining and tunneling, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Australian companies WDS Limited and Cram Fluid Power, the engineering department of J.H. Fletcher & Company was tasked to design and manufacture roof bolting modules to be mounted off both sides of a roadheader, providing in-cycle bolting. The objective was to produce a boom and bolt module that would allow an operator to bolt from a remote location, eliminating the need for miner to work in unsupported ground. The bolt module needed to operate in front of the cutting boom, but retract to a parked position out of the way during the cutting cycle. Due to Australian electrical approval requirements, it was desirable to design the module with minimal use of electrical controls. The need for multiple, complex, drill steel and bolt handling steps led to the need for a custom hydraulics package to automate several of the movements. The result of the design is dual drill and bolt modules mounted to a multistage boom with over 24 feet (7.31 m) of extension. Each unit rotates and tilts to meet the bolt pattern requirements in conjunction with the stow and load requirements. The bolt module builds on previous designs incorporating a modular assembly with each sub-component designed to be replaceable and adjustable independently from other machine components. Each major component is painted a different color to help the operator make the connection visually from the module to the operator?s control valves. Hydraulic package valves were designed to automatically control several of the sub-components during the drill cycle, reducing the number of steps a drill operator would, otherwise, have to do manually. This design removes the operator from working in unsupported roof and away from other inherent hazards, putting them at a safe distance on the operator?s platform. The cutting and bolting equipment has been combined into one machine, which is advantageous in single entry drifts because there is no need to place change equipment. The hydraulic package valves eliminate the need for any electronics, thus avoiding any electrical regulations with respect to the controls. The addition of these modules to the roadheading machine increases miner safety and streamlines production while meeting the ground control support requirements.

Jan 1, 2014

By Joel Bradley, Kot Unrug, Kyle Perry, Mark Klimek

"A West Kentucky mine operation in No. 11 seam, encountered floor heave, due to the localized increase of the thickness in the fireclay mine floor. Floor heave has overridden seals installed in two mined out panels. The third seal’s location was planned for isolating that area from the Mains. A plan of support has been developed to prevent repetition of the floor heave and related problems outby the seals. The applied ground control measures were successful. An attempt of a 3D numerical modeling was made, that it would match the observed behavior of the mine floor and could be used as a design tool in similar conditions. In the paper described are sequence of events, a mitigation ground control system applied, and the first stage of numerical modeling.IntroductionWest Kentucky coal mine operation in the No. 11 seam has approached an area where the fireclay floor thickness increases to about 5 ft. Delayed floor heave has been observed. In the first sealed area (Panel KK), floor heave has overridden the seals and has begun to progress outby. This could not be allowed at the new seal location PP described in this paper because such override would affect the mains. Previously numbers of standing support systems were used, but their effectiveness was not satisfactory as is illustrated in Figure 1, Figure 2, and Figure 3. Therefore, with sealing of the next area approaching, mine management was looking for a better solution that would eliminate the problem. In that stage, our team looked closely at the geology and strength of roof and floor, as well as the characteristics of ground failure around the seal at the first site. The technical literature has been searched as well Haramy et al. 1986 Hsiung and Peng 1987, Peng 2008, Santos & Bieniawski 1987. This led to the identification of factors responsible for the ground failure. It has been determined that increased fireclay thickness from typically less than 2 ft to about 5 ft, when compared to the previously mined parts of reserve, and the strong limestone strata just above the immediate roof composed of 2 ft of black shale, created conditions of failure. It appeared that, when pillars were punching into the mine floor, the strong roof did not break but was bending, exerting high pressure on outby pillars, causing rib failures and closure. This is a similar mechanism to a strong roof affecting longwall shields. The remedial action planned was additional support."

Jan 1, 2015

By Kot F. v. Unrug

In spite of the extensive research and accumulated experience from mining operations, an appropriate pillar design remains an open issue. Due to the shrinking reserve base, present mining operations move to more challenging conditions. There are usually thinner seams and geologic conditions are often unfavorable. For instance, mine roof and floor are weak or deteriorate rapidly when exposed to moisture fluctuations in mine atmosphere. It is common that pillars of current operations are more- squat than several decades ago when the bulk of pillar research have been carried out in thicker seams. The methods of pillars calculations were developed regionally (in particular countries) to suit design needs for the most important seams, from which the majority of coal production was coming (e.g. Pittsburg or Pond Creek seams in the eastern of US). Most of the pillar formulae use similar approach by assigning weights (using constants) to the influence of coal (seam) strength and pillar widthheight ratio on its final strength. That mechanistic approach has sound theoretical base and good data supporting its validity. However, what seems to be missing is a qualification system of the mine conditions, which are outside of the data base or do not comply with the theoretical model applied in pillar strength formulae. This paper attempts to address that issue in two major categories, first when only a drill core data are available, and second during the mine development observations can be made directly on a coal seam. The composition of a coal seam is also addressed, (which often changes rapidly across the reserve), and discussed its influence on pillar's structural performance. In summary a set of practical design rules is presented.

Jan 1, 2005

By Michael Kelly

Current research in longwall mining in CSIRO Exploration & Mining is focused within five major projects and several minor projects. The major projects are: 1 3D Aspects of Longwall Geomechanics. This was reported to the conference last year and a final report will be available by mid-2001. 2 Mine Gas Control. This just completed project centred on Dartbrook Colliery which has a longwall gas make of more than 8 cubic metres per second. 3 Rapid Roadway Development This includes the construction of an autonomous conveying and bolting module (ACBM) that sits between the miner and haulage system. 4 Top Coal Caving In conjunction with the YanKuang group in China, CSIRO and the University of NSW are conducting a prefeasibility study of the Top Coal Caving method in Australian conditions. 5 Longwall Automation. In partnership with the Cooperative Research Centre for Mining Technology and Equipment (CMTE), the CSIRO has conducted a scoping study on this issue and will commence an initial three-year demonstration project in July this year. This paper describes these protects in more detail with particular focus on the last three in the above list.

Jan 1, 2001

By Lu Jiam Zhang

Coal and gas outburst is one of the serious natural disasters in the coal mines of China. Since 1950, more than 10,000 coal or gas outbursts have occurred in more than 200 underground coal mines of different types. The outburst prone coal mines are widely spread out. It occurs in different types of coal -ma and is very serious in some areas. Most outbursts occurred at the time of roadway driving in coal seam, serious outbursts occurred mainly when entering the coal seam during the cross-cut driving; of the outbursts, coal and gas outbursts We UP major proportion, while pressing out and pouring out ah account for a large proportion; outburst. occur under different operating conditions, but mostly occur during shotfiring. This paper introduces the prevention and control measures as practiced in China and illustrates the three types of outburst cla8sification. Both technology and management are equally important in outburst prevention and control. Measurement of the volume of drilling cuttings and the initial gas outflow rate fm- boreholes have proven to be effective. A special team and organization must be set up to deal with the problems.

Jan 1, 1987