Search Documents

By Michael DiMatteo, Michael D. Gardner, Eric F. Perry, John K. Felbinger, Robert S. Evans

A hydrologically isolated surface coal mine was reclaimed using acid material handling, alkaline addition and ground-water management techniques. Eight pit floor drains were installed during reclamation to intercept ground-water flow in the mine backfill and minimize water table buildup. All drains began flowing within six months of installation. Water quality and ground-water discharge have been monitored for four years after mine closure. A thin water table aquifer about five to seven feet thick has developed in minespoil about 20 to 40 feet thick. Ground-water flow direction is largely controlled by geologic structure and the drains. Median ground- water discharge is about 0.43 gallons per acre per minute, and varies an order of magnitude between wet and dry seasons. About 19 % of precipitation enters the aquifer as recharge. Seven of the eight drains typically discharge net alkaline water. Alkalinity is produced continuously and concentrations are highest during dry periods. Conversely, sulfate and acidity concentrations increase during wet periods as slugs of accumulated acid products are leached. Overall water quality is controlled principally by minespoil geochemistry and added alkaline material. The drains have successfully directed ground-water to a planned discharge area. Without the drains, a ground-water mound was expected to form against a buried highwall and discharge over a large area.

Jan 1, 2000

By S. D. Thompson, J. C. Dzurino

This investigation mainly focused on designing a bunker system for a large underground coal mine. The primary purpose of this bunker system was to keep high- and low-sulfur coal segregated on the underground belt system. These bunkers were also required for protecting the mine faces from out by belt delays. Methodologies used in developing this plan are briefly discussed. The final design and the procedures formulated for implementing it are also presented.

Jan 1, 1987

A new separator, known as the HydroFloat cell, was developed to overcome the limitations of traditional flotation cells in recovering coarse particles. The HydroFloat cell separates particles based on differences in mass after the selective attachment of air bubbles to the hydrophobic component of the feed stream. Proof-of-concept testing, utilizing phosphate matrix, heavy mineral sands and anthracite slag, indicated that significant improvements in separation efficiency can be achieved using this air-assisted teeter-bed system. Based on the encouraging laboratory results, a pilot-scale HydroFloat cell was fabricated and installed at a central Florida phosphate plant. Test data collected using the pilot-scale unit suggest that the BPL recovery of the +35-mesh plant feed can be increased by snore than 40% through the application of this new technology. This improvement is particularly beneficial due to the very high grade (-73% BPL) of the +16-mesh particles in the HydroFloat concentrate. This article describes the theoretical basis for the development of the HydroFloat cell and provides an overview of recent laboratory and pilot-scale test results.

Jan 1, 2002

By E. T. Pecina

Bioleaching is a viable option for the processing of auriargentiferous refractory ores with high arsenic content. The application of mesophilic (A. ferrooxidans and ?L. ferrooxidans?) and thermophilic bacteria of the genus Sulfolobus (S. solfataricus and S. acidocaldarius) as oxidant treatment before the cyanidation of an industrial arsenical pyrite concentrate is presented. The results show that extraction of gold and silver increases due to bio-oxidation caused by mesophilic bacteria and results in a maximum gold recovery of 68%. In all strains studied, biooxidation resulted in an average silver recovery of 50%. The results showed that all evaluated strains were sensitive to solids content (5 to 20%) and average particle size (75 and 38 µm) of the concentrate.

Jan 1, 2010

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"There are three distinct producing iron ranges in Minnesota, the Vermilion, Mesabi and Cuyuna. In trend the Vermilion and Mesabi are approximately parallel (E.N.E. and W.S.W.) and about fifteen to twenty miles apart. The Vermilion lies farthest north, near the. Canadian boundary. It is from seventy-five to eighty miles due north of Duluth. The length of its productive part is about twenty miles.The Mesabi Range is from fifty to seventy-five miles north and northwest of Duluth. Its length along the strike is about 110 miles, and the length of its present productive area about eighty miles. The Cuyuna range lies southwest of Duluth nearly ninety miles, and is the last of the Lake Superior iron ranges to be developed. The relative positions of the ranges are shown on an accompanying map. The Mesabi Range is by far the largest producer and contains the largest ore reserves of the three. The Cuyuna is next in quantity of proven ore, and in production since 1916, while the Vermilion is first in average quality of ore.On the west, both Vermilion and Mesabi ranges disappear beneath heavy glacial drift; and on the east, extend into Canada, the so-called Gunflint range near the international boundary being an eastward continuation of the Mesabi formation. This latter range is of no economic importance, however, at present. The exploration and development of the Cuyuna range has proved up a considerable tonnage of manganiferous iron ore, besides ordinary merchantable iron ore."

Jan 1, 1920

This chapter looks at the development and use of the operating budget. This is management's plan of action in the short term, usually one year. The operating budget includes all expensed production costs (i.e., all costs reported as cost of goods sold) but does not include expenditures on capital equipment, which are usually justified using discounted cash flow techniques.

Jan 1, 1999

By John B. Ackerman, John G. Mansanti

INTRODUCTION Placer Dome's Turquoise Ridge Joint Venture operation is located some 75 km northeast of Winnemucca, a community in north central Nevada. Formerly known as the Getchell Gold Corporation and First Miss Gold, the operation mines refractory ore from the Getchell and Turquoise Ridge gold deposits located on the east flank of the Osgood Mountain Range above the Kelly Creek Basin in the Potosi Mining District. Mining has been ongoing at Getchell since shortly after its discovery in 1934, and was the nation's second leading producer of gold after Homestake in the early 1940s. Over its history the Getchell property has been mined for gold, tungsten, molybdenum and arsenic; mining methods varied from open pit mining to underground mining; processing options included conventional milling, flotation, roasting, heap leaching, and most recently pressure oxidation followed by CIL (carbon-in-leach). As an historical note, the US Bureau of Mines developed the use of carbon for gold recovery at Getchell during the 1940s (Horton 1999). Placer Dome acquired the property in May 1999. The pressure oxidation plant was mothballed in July 1999 and the property was placed on care and maintenance in February 2002 pending further exploration results. The property is currently ramping up to full production status. A joint venture agreement (75% Placer Dome, 25% Newmont) was established with Newmont Mining in 2003 and ore is processed at their nearby Twin Creeks autoclave plant. Mine dewatering is a key element to success. Arsenic is a ubiquitous mineral in many of the mineralized areas of northern Nevada, necessitating treatment of water prior to re-infiltration.

Jan 1, 2005

By David A. Lindsey

The world-famous beryllium deposits at Spor Mountain, northwest of Delta, Utah, are the principal resource of beryllium in the United States. Beryllium metal, beryllium-metal alloys, and beryllium oxide ceramics have a long history of specialty applications. Beryllium is used in X-ray windows, nuclear reactors: and a wide variety of industrial and electronic products. The Spor Mountain deposits are located on the western rim of the Thomas caldera, one of at least three volcanic depressions that subsided during voluminous eruption of rhyolitic ash-flow tuff in early Oligocene time. Beginning in early Miocene time, the caldera rim and its volcanic fill were cut extensively by basin-and-range faults. Basin-and-range faulting was accompanied by local eruption of high-silica rhyolite. High-silica topaz rhyolites at Spor Mountain (21 Ma) and Topaz Mountain (6 to 7 Ma) are especially rich in fluorine and lithophile trace elements such as beryllium. Topaz rhyolite of the Miocene Spor Mountain Formation, or its magma was the source of the Spor Mountain beryllium deposits. At Spor Mountain, deposits of beryllium, as submicroscopic bertrandite, Be4Si207(OH)2, occur in rhyolite tuff beneath flows and domes of topaz rhyolite. The beryllium deposits also contain minor disseminated fluorite, lithium, uranium, and anomalous traces of other lithophile elements. The host tuff, originally composed of glass, zeolite, and abundant clasts of carbonate rock, has been altered to clay and potassium feldspar. Fluorite, quartz, and opal replaced carbonate clasts in the tuff. Beryllium was deposited with fluorite in altered clasts and in the matrix of altered tuff. Fluorspar and uranium deposits are spatially and genetically associated with the beryllium deposits at Spor Mountain. Fluorspar deposits at Spor Mountain occur mostly in breccia pipes. Some fluorspar pipes contain uranium, thought to be dispersed in the structure of fluorite. Secondary uranium minerals are dispersed throughout the tuff that hosts beryllium deposits and comprise lenses of ore-grade uranium at the Yellow Chief mine.

Jan 1, 2001

By J. A. Procarione, M. K. McCarter, Bradley C. Paul

A numerical technique is described which can be used to model the quantity and distribution of air flow through broken rock. The method can also describe gas concentration and temperature distribution. A computer code implementing the numerical approach was developed to assist in determining the feasibility of a proposed modified in-situ leaching method for extracting copper from sulfide porphyry deposits. This mining method requires air to be forced through cells of rubblized ore. The flow serves to supply oxygen for the leaching reactions and to dissipate heat that would other-wise build due to the exothermic reactions. The method substitutes the Carman equation into the Laplace equation. The solution of the resulting non-linear formulation is done on a finite difference grid using SOR with iteration improvement of coefficients. This procedure yields the required air flow pattern and pressure drop. An equation for advection with absorption is then solved over the same grid using explicit schemes to yield oxygen concentration. Finally, a similar technique is applied to the convective heat transfer formula to yield the temperature profile. The model is potentially applicable to such mining problems as the prediction of leakage through caved ground, the prediction of methane concentration in gobbed ground, and the prediction of heat build-up in caved workings.

Jan 1, 1989

By R. Kneisley, D. Conover, K. Haramy, K. Hanna

INTRODUCTION Coal mine entry intersections are high-risk areas for roof falls due to inherently wide roof spans, excessive stress, and variable intersection shapes resulting from breakthrough misalignments. Statistics from underground coal mines reveal that a high percentage of injuries occurs from roof and rib falls in entry intersections (Peng, 1980). The U.S. Department of the Interior, Bureau of Mines, is conducting a field research project to investigate failure modes surrounding underground coal mine entry intersections. The research objectives are to (1) develop a method to determine failure modes and stress-displacement relations around coal mine intersections and (2) develop engineering guidelines and empirical relationships for use in designing safer coal mine entry intersections. The basic approach to achieve the objectives is to instrument and monitor intersections before, during, and after intersection development in order to determine contributing parameters, such as in situ stresses, stress changes, strata movement, geology, physical properties, and mining sequence, that may influence the short- and long-term stability of the intersection and adjacent entries. This paper describes a rock mechanics instrumentation program, data analyses, and a comparison of two case studies conducted at two underground mines, designated as "A" and "B", in the Illinois Coal Basin. The instrumentation plans and data collected during development and long-term monitoring of four-way intersections and adjoining entries are presented. Data analyses of pre- and post-mining roof stress, pillar loading, strata movement, roof bolt loading, and geologic features are included. INTERSECTION FAILURE MECHANISM The region surrounding an entry intersection is characterized by different failure criteria than the region surrounding a single entry. Stresses induced during intersection development may result in a high incidence of roof and rib failures. Various numerical modeling techniques have been used to evaluate the failure modes surrounding intersections (Gercek, 1982; Chugh et al., 1975). Numerical modeling techniques include problems associated with the analysis of post-failure behavior, provision for different horizontal stresses (i.e., 01 f 021, and determination of inputs required for any non-elastic behavior. It seems likely that more sophisticated failure criteria, based on actual field data, are needed. The Bureau of Mines has conducted an extensive instrumentation program to investigate actual intersection failure mechanisms and to provide an improved understanding of stresses and deflections using beam and plate theories. Beam theory is not applicable to analyzing intersections (Wright et al., 1964); however, it can be used to explain roof deflection and failure (shear and flexure) of adjacent entries and to provide an improved understanding of stress changes and displacements as the entries, crosscuts, and intersection are developed (Hanna et al., 1985). Beam theory may be used for entries when the roof length is twice the width. When the length is less than twice the width (as in intersections), the roof must be analyzed as a three-dimensional problem, and stress and deflection calculations are based on flat plate theory (Adler and Sun, 1976). The confined-core theory (Wilson, 1972) hypothesizes that within a typical pillar, two regions exist: a confined-core region where the horizontal confining pressure is uniform and approximately equal to the overburden pressure, and a yield zone where the vertical pressure increases from nearly zero at the rib to a pressure peak at the boundary of the yield zone. The strength of coal in the yield zone ranges from nearly zero at the rib to nearly full strength at the confined core. The vertical stress in the confined core decreases from maximum at the yield zone boundary to the overburden pressure some distance into the pillar. Excavation of the adjoining entries

Jan 1, 1986

Successful longwall gate entry design requires control of vertical and horizontal stresses. Vertical, or overburden, stresses are most severe in the tailgate where they are concentrated by longwall panel extraction. Horizontal stresses can also be highly destructive but they are less well understood. This paper discusses measurements of in situ horizontal stress fields in the eastern United States, experience with horizontal stress in longwall mines and methods for predicting and controlling horizontal stresses. The information presented was collected through site investigations at 45 US longwalls and an international literature review.

Jan 1, 1992

By Y. Ye, J. D. Miller

Certain bituminous coals are known to contain appreciable quantities of natural fossil or subfossil resin. Such resinous coals are found in the western US, particularly the Wasatch Plateau coalfield of UT. Some of the seams in this field contain an average of 5% resin. This fossil resin has been recovered by gravity and/or flotation processes since 1929. Resin concentrates thus produced are of low quality and are usually refined by solvent extraction. The purified resins are of commercial importance in the adhesive, coating, rubber. and ink industries, etc. An improved flotation technique has been developed which involves ozone conditioning to selectively float resin from high-volatile bituminous coal. With this flotation process, a concentrate product which contains 95%

Jan 1, 1990

By G. Buchan

This paper discusses the design of long panels for longwall mining at Twentymile Coal Company (TCC) from conception to implementation. The case study of the long panels at Twentymile includes extensive mine plan reengineering in the early 1990's to world record production months in 1996 and 1997. The obstacles of subsidence engineering, environmental regulations, conveyance, ventilation, equipment design, and continuous miner (CM) development timing had to be overcome to successfully begin longwall production within a 4 year time frame. The background and some detail for each of these areas listed will be discussed to show how the coordination of many facets must be pulled together to implement a successful long panel mine plan.

Jan 1, 1998

By D. Harris, M. Osterberg

This paper examines the economics of acquiring mineral exploration rights by royalty-rate bidding when the royalty basis does not provide for full cost recovery. Bidding takes place prior to exploration and the documentation of actual tonnage and grade. Consequently, it increases considerably the risk to exploration capital when the fraction of cost recovered is small and the product price exhibits large fluctuations. Price and grade risk are demonstrated on a 360-Mt (400-million-st) porphyry copper deposit by Monte Carlo simulation of discounted-cash-flow analysis. Copper price is modeled as a stochastic price process, and costs are based on US Bureau of Mines cost models. When both grade and price risk are considered, the probability for a negative NPV is 0.54, given a royalty rate of 5% applied to a basis that allows the recovery of costs up to 50% of product price. Investment risk could be considerably reduced by defining the royalty basis to allow greater cost recovery. Although such a basis would require society to share in the risk, society would benefit from greater resource development.

Jan 1, 2000

By J. Bigu

Use has been made of several theoretical models to predict radiation levels in underground uranium mines. The models used are the Evans model, the Thomas-Epps mine model, the isolated mine model, the mine tunnel with no air flow and the mine tunnel with air flow (Beckman and Holub). Calculations based on the above models have been extended to include thoron gas and its progeny, a common occurrence in some Canadian uranium mines. Theoretical predictions include radon and thoron progenies WLs and concentrations, and some ratios of great practical interest. The main differences between the models are pointed out and comparison is made with experimental data gathered during the last three years in several Canadian underground uranium mines.

Jan 1, 1981

By Kevin D. Lofftus

This paper presents a dynamic model for column flotation. The model equations are normalized and the dimensionless groups that are directly responsible in determining the column flotation behavior are identified. The resulting model equations are incorporated for computer simulation. Numerical results from computer simulations are analyzed to gather information about design and operation of column flotation devices.

Jan 1, 1988

By D. A. Rice, R. G. Swanton, A. May, O. C. Carter

As part of a cooperative effort between the US Bureau of Mines and the Florida Institute of Phosphate Research (FIPR), with input from the phosphate industry, the conversion of phosphogypsum to sulfur is being investigated. The proposed process incorporates a thermal reduction of phosphogypsum to calcium sulfide (CaS) and a hydrometallurgical treatment to convert calcium sulfide to ammonium bisulfide (NH4SH), which is then oxidized using a catalyst to produce elemental sulfur. The paper summarizes the results of continuing laboratory studies using an activated carbon catalyst which was loaded with sulfur through oxidation of ammonium bisulfide solution. The extraction of the sulfur that forms in situ on the catalyst is a key area in the development of the sulfur recovery process. Two approaches for removing the sulfur are being investigated: (1) thermal treatment to volatilize sulfur. and (2) leaching the sulfur using liquid anhydrous ammonia. The research has shown that it is technically feasible to recover over 90% of the sulfur from the carbon by either volatilization or ammonia leaching. Locked cycle testing has demonstrated that the carbon has the potential to be recycled after ammonia leaching.

Jan 1, 1987

By Christopher Haycocks

Self-supporting, open stoping underground mining methods are some of the earliest, starting with the prehistoric flint mines of Europe and the Egyptian gold mines of Nubia in the time of the pharaohs. When the early miner created an opening, it had to be inherently stable and self-supporting to enable him to continue. Therefore, as mining progressed beyond simple gophering, self-supported open stoping methods were devised to meet the needs of individual ore bodies. Timber for support appears in mines as early as 1000 BC, but this was for no more than local ground control. The ingenuity of mining engineers through history has so refined open stoping methods that today they produce more tonnage than any other mining system. Self-supported open stoping finds its application in moderate to strong rocks that exhibit little jointing or fiagmentation. Good back, hanging wall, and footwall conditions that require no more than incidental support are an essential part of these mining methods. Open stoping methods find applications in all inclinations of ore body from flat to vertical, and where ore movement may be either mechanical or under the influence of gravity. Table 18.0.1 demonstrates the range of ore bodies suitable for open stoping, with particular reference to their dip and the deposit thickness. Most of the flat-dipping applications use ore pillars for overall support and ground control that may be recovered under some conditions after completion of normal stoping practices. In steeper ore bodies, rib, crown, and sill pillars used to block out the ore may be recovered subsequent to the completion of stoping. Open stopes are frequently filled to facilitate pillar recovery. Two of the methods, vertical crater retreat (VCR) and shrinkage stoping, utilize fragmented ore for temporary support in the stopes. In these two cases, the stope is not strictly open until after drawdown.

Jan 1, 2008

By Liam Findlay

Optimizing a production schedule with semi-mobile in-pit crushing & conveyance (IPCC) requires integrating extraction sequence, destination policy, crusher relocation, conveyor layout, and truck fleet investment decisions. An integrated stochastic optimization framework is proposed to produce long-term schedules for mining complexes using multiple semi-mobile IPCC systems. The optimizer selects the crusher locations and designs the conveyor routes from anywhere in the mines. The stochastic framework considers simulated multi-element orebody realizations and manages associated risk. A hybrid metaheuristic based on simulated annealing and evolutionary algorithm is implemented for the optimization. The method is demonstrated using an iron ore mining complex.

Jun 25, 2023

By Por J. B. Evans

El mantener un beneficio óptimo sobre todo el conjunto de un emplazamiento minero necesita una constante puesta al día de las estrategias operativas. En esencia, cada estrategia es una combinación particular del gasto del capital previsto, el flujo de ingresos y el tiempo transcurrido. La selección de una estrategia basada en el beneficio potencial requiere que cada estrategia contemplada con un ordenador, un análisis tal puede ser engorroso. Este capítulo discute o desarrolla una técnica de "corte rápido" que asigna una relación de beneficio a las estrategias alternativas e identifica aquellos aspectos de una estrategia que producen mayor impacto sobre el beneficio. Esta técnica puede proporcionar valoraciones rápidas de suficiente precision para muchas de las decisiones de las estrategias operativas que se toman sobre la marcha en minas que se encuentran en explotación.

Jan 1, 1982