Search Documents

By N. Zouridakis

Radon is an established lung carcinogen and remains the most important environmental radiation exposure. It was estimated that inhalation of radon and its short-lived decay products accounts on average for about one half of the effective dose equivalent from all natural sources of radiation. Radon contained in household water can transferred into room air as a result of agitation or heating. An indoor air concentration of 400 Bq/m3 is obtained if the radon concentration in household water is 4 kBq/L. A typical concentration of radon in ground water is about 1000 times lower than this concentration but sometime elevated concentrations of some kBq/L in ground water are reported. In this work a Liquid Scintillation counting system is used to obtain fast and accurate measurements of radon (222Rn) in water samples from Argolida, Greece.

Jan 1, 2007

By Sergio Godoy P.

The Los Bronces porphyry copper deposit is located in the high Andes of Central Chile. Ore is mined from several tourmaline breccias and from an earlier porphyry. After years of experience in the geostatistical estimation of reserves in different zones of the ore body, we believe that success lies in considering the evaluation as an integrated process beginning with the analyses of the drilling density and sampling methodology, ending with the critically important reconciliation between the estimated and the actually extracted ore, in general, when errors or differences occur, focus is centered in the calculation stages of geostatistics. However, this paper demonstrates that all the evaluation stages are equally important and require the direct and continuous geologic input to ensure the best possible estimate within the frame of the geologic constraints.

Jan 1, 1992

The heat of immersion of coals in different immersional liquids is measured as a function of particle size and moisture content. Decrease in particle size shows a concomitant increase in the heat of immersion. The heat of immersion is dependent upon the nature of immersional fluids. In addition the nature of moisture present in coal influences the heat of immersion.

Jan 1, 1993

By D. A. Poulter

The stability of a liner system is influenced by many factors which can be compiled into four basic groups. They are: 1. the liner system components and physical characteristics; 2. the geometry and slope of the liner system; 3. the loading conditions on the liner system; and 4. the foundation conditions under the liner system. Failures in the liner system that are due to one or more factors from the first three groups usually result in movement relative to the plans of the liner system. Failures associated with factors in the fourth group result in deformation(s) across the liner system section beyond its design limits. For purposes of these discussions a failure in the liner system refers to displacements or movements resulting in physical damage to the liner system such that it can no longer function.

Jan 1, 1995

By Pasi Latva-Pukkila

Underground rock drilling has gone through intense development during the last 25 years. Mechanization and hydraulics have greatly increased the efficiency of drilling and improved the environment of the drill operator. As the total economy has become more and more important, the development has resulted in greater overall economy in drilling. The latest evolution step is computerization of drilling equipment. Computerization has been applied to tunnelling jumbos, long- hole drilling rigs and bolting rigs. With today's technology computerization is the natural way to increase capacity and productivity of the drilling process. However, it is still impractical to implement total "robotic" drilling. In computerized drilling the operator's role continues to be vital in controlling the drilling process and in analyzing the effect of individual parameters on the whole excavation process. Today this is called "CAD" - Computer Aided Drilling.

Jan 1, 1989

By J. Peck, M. J. Scoble, C. Hendricks

This paper is based on field studies in North American surface mines. The work involved the adaptation of microprocessor-based instrumentation to monitor various operating parameters on-board rotary blasthole drills and mining shovels. Following a review of instrumentation and monitoring methodology - drawing on experience gained under field conditions-the paper will focus on the application of monitoring technology within the framework of an Integrated Equipment Monitoring System. Such a system will permit real-time performance evaluation of key equipment involved in surface mine production. Drill performance monitoring has been demonstrated through work to date, to provide significant input into blast design, reserve estimation, mine planning and production control processes, through an improved facility for ground characterization. Monitoring excavation equipment has been proven valuable in assessing how effectively the input from drill monitored data has been used in the evolution of blast designs. This specifically refers to assessing blast efficiency through measuring associated levels of excavator performance in relation to muckpile characteristics. The medium-term goal of equipment instrumentation and monitoring has been to assist mines in optimizing the overall rock breakage and handling process. Based on the reported results, this has been accomplished. Long-term efforts now concern using a greater understanding of equipment performance and response to varying operating conditions as a foundation for the implementation of mining automation.

Jan 1, 1993

By M. S. Prasad, K. J. Reid, M. P. Katsoulis

The State of Minnesota is interested in stimulating the development of clay resources and recently supported a two-year project to collect data on geological, mineralogical, processing, economic and environmental aspects of such potential developments. This paper presents the various process options adopted on bulk samples collected from the Minnesota River Valley area, which is a primary deposit and contains a major silica fraction. A standard test flowsheet involving degritting, dispersion. HGMS and cycloning was developed and for some samples yielded an acceptable filler grade product. Secondary streams containing relatively high grade kaolin but of coarse size were also obtained. Improvement in particle size distribution and in physical properties related to paper product specifications (brightness, viscosity) were obtained by size-reduction processes. Market and economic considerations for kaolin consumption in the upper Midwest are analyzed. Current markets for paper grade kaolin in Minnesota are briefly discussed.

Jan 1, 1992

By Ernst Langer

INTRODUCTION Morro do Niquel is located near the small town of Pratdáolis in the southwest part of the State of Minas Gerais, Brazil, about 300 km in a straight line north of São Paulo and 300 krn west of Belo Horizonte. The deposit is known since 1935. Systematic exploration started, however, only in 1957 and production with one furnace in 1962. Since 1969, after the installation of a second furnace, the mine produces about 2 500 tons of nickel, contained in ferronickel, per year. This production is now consumed totally by the Brazilian steel industry. The "Morro do Niquel" is a serpentinite stock of 900 by 400 m which rises 200 m high above the surrounding metamorphic rocks of Algokian age (see Figure 1). On top of the hill there is a leached barren zone of about 200 by 400 m, generally 20-30 m deep, which consists practically only of a boxwork of quartz colored brown by limonite. Surrounding this zone on the sides of the hill is weathered, decomposed serpentinite which contains about 213 of the economic nickel mineralization. Roughly 113 of the ore reserves lie below the leached overburden representing ore of a different type. The geological map and cross-section, Figure 2, give a clear picture of the occurrence.

Jan 1, 1979

By C. Bazin, D. Hodouin

Dynamic experiments were performed in a continuous open-circuit 40x40-cm ball mill using a pseudo-random binary sequence of the feed rate and measuring the variations of the discharge particle-size distribution. The impulse response is calculated by a cross-correlation technique. Then a model involving a discrete transferfunction and a time-series stochastic equation is calibrated using maximum likelihood methods. Based on this empirical model, a minimum variance controller with constrained input is designed and its performances are compared, by simulation, to the performances of a conventional PID regulator.

Jan 1, 1987

By Gordon S. Thomas

The problem of how best to exploit a reserve has vexed mine planners and design engineers since mining began. The cyclic nature of the mine design-scheduling problem, combined with the lack of good mathematical tools for tackling it, have ensured that it has been, and will continue to be, a major challenge for operations researchers working in mining. This paper reviews the current state of the art in pit optimisation and scheduling algorithms. Starting from the inception of the first block models in the late 1950's, it progresses through the developments and applications of the Moving Cone algorithm, the Lerchs Grossmann 3D Graph Theory algorithm and some of the heuristics, to the new artificial intelligence techniques that are being applied today. Along the way, it discusses the limitations of the various approaches and lays the foundations for the research that is currently being undertaken by CSIRO and others in the field of mine production scheduling and control.

Jan 1, 1996

By J. S. Stachulak

Installation of a computerized mine monitoring and control system in two planned construction phases began in 1983. Phase one consisted of providing a central monitoring station located on surface for monitoring underground CO detection in Frood Mine's heated area. The implementation of this project annualized labour savings of $200,000. The cost of installation of an early fire warning system was $100,000. There are several CO sensor monitoring carbon monoxide trends through mine heated areas. To obtain an early warning, it is not good enough to know that a fire has started, but it is also necessary to know where the fire is located.

Jan 1, 1989

By Marian W. Otrebski, Julian A. Korneck

Long distance, overland conveyors require significant capital outlay of which up to 70% may be contributed to the cost of belting. Significant savings may be achieved by identifying possible risk areas and applying modern technology methods to reduce or eliminate risk. Recently, Sasol Coal commissioned an overland belt conveyor system comprising three belt conveyors of 7 km, 5 km and 4.5 km in length. These were designed and constructed taking the above into consideration. Contained in the paper are the belt conveyor system requirements, designing assumptions and methods applied in the designing process as well as ways and means to eliminate or at least reduce risks.

Jan 1, 1998

By L. F. Barrett, D. E. Cameron, J. C. Wilson

Exploration by Anaconda Minerals Co. in the Rico area from 1978 through 1983 resulted in dis¬covery of the Silver Creek molybdenum deposit. The drill-indicated resource is 40 Mt (44 million st) of 0.31% Mo, and projections suggest that the deposit may exceed 182 Mt (200 million st). No source intrusion has been intersected by drilling, but its presence is sugested by intramineral silicic alkali-alaskite porphyry dikes observed at the surface and in drill holes. Age dates and fluid inclusion studies indicate that the deposit was formed 5.2 ± 0.2 m.y. ago and that more than 1200 (3937 ft) of cover has since been removed by erosion. The deposit is hosted by Precambrian quartzite and greenstone, and Paleozoic sediments. Three prominent faults intersect in the vicinity of the molybdenum deposit, and one of these, the Last Chance fault, strongly influenced the shape and location of the deposit. The juxtaposition of host rocks across the Last Chance fault reflects significant offset spanning at least three different periods. Wallrock alteration associated with the deposit includes potassic, phyllic, and propylitic zones in noncalcareous rocks and garnet and anhydrite-diopside zones in the carbonates. All +0.2% Mo mineralization is within the potassic and garnet zones. Premineral faults that intersect the deposit contain the only surface molybdenum, tungsten, and fluorine anomalies. Dispersion halos of the indicator elements were defined by drilling in the discovery phase of exploration, and are particularly well-developed in the hanging wall of the Last Chance fault.

Jan 1, 1987

By Numan Elmas

Barite deposits located in Dinek and surrounding region have important economic features with their large reserve capacity for Turkey. The objective of this study is to elucidate geological and depositional characteristics in terms of. site investigation and chemical analysis. In order to do this, geological area of about 300 km2 was examined and detailed geological map was constructed. It was observed that Barite mineralization in these deposits was occurred in carbonate and pelitic rocks of Lower Cambrian-Lower Ordovician. Deposits were exposed to advanced diagenesis regional metamorphism and tectonics that rotated and deformed the barites; therefore, barites shows secondary veins, brecciate and fracturing structure. Even though, a few light isotope values of barites may suggest hydrothermal and exhalative sedimentary characteristics or possible mixing with magmatic fluids, generally heavy isotope values indicate that the sulfate ions were supplied from coeval seawater and, many of sedimentary features and petrological, geochemical characters support dominantly sedimentary origin.

Jan 1, 2005

By C. A. Rowland

Comminution efficiency can be expressed in three different ways. Theoretical Efficiency: actual energy consumed, in a comminution machine compared to the theoretical energy required to make the size reduction. Operating Efficiency: compares the operating work index, calculated from production comminution machinery operating data, to the Bond Work Index from bench scale comminution tests or calculated from pilot plant operating data. Economic Efficiency: income compared to planned income. Using the Bond Work Index and operating work index, this paper explains how to determine operating efficiency.

Jan 1, 1998

By J. J. Schwoebel

Resource Enterprises, Inc. (REI) is exploiting the coalbed gas resource by working in unison with active underground mining operations. At REI?s pilot project at the Soldier Canyon Mine, Carbon County, Utah, REI has drilled nearly 15,250 m of horizontal in- seam and slant boreholes during the initial two years of drilling activity. Produced gas has been sold to a natural gas transmission company on a continuous basis since mid 1983.

Jan 1, 1986

By D. Maxton

INTRODUCTION This paper traces the application of High Pressure Grinding Rolls (HPGR) at industrial and pilot scale in Australia. The Argyle Diamond Mine installed the first of two smooth segmented HPGRs during 1990 in an open-circuit secondary-tertiary crushing application to increase throughput. In 2002 a third HPGR was added to improve liberation and so increase the recovery of smaller diamonds. The latest improvements in wear technology (tyre with tungsten carbide studs) were incorporated in the design of this machine. Extensive HPGR pilot-plant trials were undertaken during the 1990s at both the Kalgoorlie Consolidate Gold Mine and the Boddington Gold Mine. The purpose of these trials was to evaluate HPGR as a method to increase throughput, as an alternative to SAG milling, and also to ascertain if downstream benefits existed. One of the challenges for HPGR circuit designers is to translate what occurs at small laboratory and pilot scale into what is likely to happen in a full-scale circuit. Scale-up from pilot machine results is normally recommended by manufacturers. However, such tests need relatively large quantities of material, particularly if meaningful data on wear are to be obtained. Laboratory tests are preferable, as they need relatively small quantities of ore, but may be questioned in terms of how they relate to full-scale operation. Modelling and simulation have played a particularly important role in this respect in Australia. Models are available which have proven to be very accurate at being able to scale throughput and specific energy response from laboratory to industrial machines. More recently, work in Australia has also been done in developing a model which has the potential to scale laboratory wear data as well.

Jan 1, 2004

By K. Y. Haramy, E. C. Westman

Anomalous geologic or stress conditions ahead of a longwall face have the potential of causing great harm to both the individual miner and the mining operation as a whole. NSA Engineering has been developing seismic tomography techniques to image the panel ahead of the face. This paper presents the results of afield effort in which a 60-m (200-ft) segment of a longwall panel containing a fault zone was surveyed daily as the face approached. Stress distribution, geologic structure and dynamic elastic properties within the panel were plotted and compared to static laboratory measurements. The surveys successfully imaged an anomalous stress concentration that was likely influenced by the presence of the fault zone. The calculated dynamic physical properties generally agreed with the laboratory measurements.

Jan 1, 1997

By Francis W. Brown, Philip R. Hunt, Douglas N. Halbe

Refractory arsenopyrite ore from Western Mining Corporation's Lancefield deposit in Western Australia is treated by fluosolids roasting of a flotation concentrate followed by cyanidation of calcine and flotation tailings. The project development is reviewed from original testwork through circuit design, operating experience, and subsequent expansion.

Jan 1, 1990

By J. D. Miller

Fluid flow phenomena and therefore the flotation efficiency of air-sparged hydrocyclone (ASH) flotation are strongly dependent on operating and design variables such as air and slurry flow rates, underflow and overflow opening areas, percent solids of the feed, reagent levels, particle size and ASH length. Time-averaged multiphase flow characteristics, as determined by X-ray CT (described in a previous publication), are used to understand and explain the steady-state ASH flotation of quartz. A detailed parametric study of quartz flotation by a nominal 2in. diam. air-sparged hydrocyclone (ASH-2C) revealed the influence of these variables on the flotation response, which is discussed in terms of the multiphase flow characteristics. Thus, a phenomenological description of quartz flotation has been established to assist in the further development and utilization of the ASH technology.

Jan 1, 1996