Search Documents

By M. A. D. Azevedo

The effect of pulping reagents on the flotation de-inking of laser printed wastepaper was investigated with regard to the removal efficiency of toner and mineral filler particles for different pH values. These results show that caustic pulping causes the toner to be released from the fibers at larger particles sizes. On the other hand, acid pulping not only causes the toner to be released at smaller particles sizes but also increases the concurrent flotation removal of mineral filler particles. It was experimentally observed that the froth generation and stability during flotation were improved for acidic pH values.

Jan 1, 1997

By Paul E. Richardson, Edwin E. Maust

Cyclic voltammetry and surface potential (photovoltage) measurements have been carried out on galena electrodes in sodium tetraborate solutions with added HC1 and NaOH to adjust the pH over the range 2 to 13. The first technique shows that the surface species formed on moderate anodic polarization and reduced on subsequent cathodic polarization are the same over the entire pH range. At anodic potentials, a soluble metal species and excess sulfur are formed; at cathodic potentials, sulfur is reduced to a soluble species. More importantly, excess surface sulfur is formed spontaneously under zero current conditions in alkaline solutions. This has been shown to occur on both polished surfaces and on virgin surfaces produced by in situ cleavage under the electrolyte. The photovoltage gives some insight into the charge and potential distribution at the galena surface. This is found to depend on past electrochemical history and the n- or p-type semiconducting character of the electrode and is interpreted in terms of changes in the surface stoichiometry that occur during reduction or oxidation. The effect of surface stoichiometry on subsequent xanthate interactions is discussed.

Jan 1, 1976

By J. Sulaiman Lubis

Indonesia is a developing country in Southeast Asia with a population of some 180 million people. It has a stable political environment and currently enjoys high rates of economic growth. Indonesia has abundant reserves of natural resources, ample for its own needs and for export. Energy resources include oil, gas and coal. The oil and gas industries are well established domestically and for export. In the last few years, though, coal industry development has been rapid. Coal resources from bituminous to lignite amount to more than 30 Gt (33 billion st). That is more than enough to meet domestic needs and provide significant amounts for export. Figure 1 shows coal basins in Indonesia. Coals in Indonesia are generally young steaming coals. They are very low ash and sulfur, high volatile, bituminous B and C. The Indonesian government's state coal company is called Perum Tambang Batubara. The company has actively promoted the development of its coal for domestic and export markets. In particular, the government has placed priority on non-oil exports of which coal is a major element. The government strives to honor all contractural commitments for the export of Indonesian coal from contractor, private and government mines. From 1987 through 1989, coal production has increased from about 3 Mt (3.3 million st) to 9 Mt (9.9 million st). Exports have grown from I Mt (1.1 million st) to 3 Mt (3.3 million st). These are significant increases for a small industry with limited infrastructure. But with growing investment and development, these production and export levels will increase substantially, and Indonesia will be a significant world supplier of coal in the 1990s.

Jan 1, 1990

By LaPoint D. J.

Copper deposits in sandstones are excellent targets for open pit mines using SX-EW extraction and processing methods. The mineralogy consists of chalcocite as the primary sulfide and copper carbonates and sulfates in the zone of oxidation. Two general deposit types are recognized: early diagenetic copper deposits that are associated with the reddening of the surrounding sediments, and epigenetic deposits that are associated with the migration of copper-rich basinal fluids along faults into permeable reservoir beds with a source of reductant. Epigenetic copper deposits are more likely to contain enough tonnage to be economic.

Jan 1, 1996

By Hassan El-Shall, El-Sayed A. Abdel Aal

The major goal of this study is to decrease iron content in wet-process phosphoric acid. Reducing the amount of post-precipitated sludge in the acid is another important objective in this investigation. In order to achieve these goals, research efforts have focused on bench scale testing of an iron-chelating reagent to remove iron from phosphoric acid produced from South Florida high-iron and -magnesium phosphate concentrate, and plant testing using freshly produced concentrated acids for reducing the post- precipitated sludge. The data obtained in the above studies suggest that the addition point of the precipitating reagent is very important, as the precipitated iron compound has higher solubility at higher P2O5 concentrations. Up to 60% Fe2O3 removal efficiency is achieved depending on the amount of the reagent, concentration of acid used, and operating conditions. The addition of precipitating reagents to freshly concentrated phosphoric acid leads to a decrease of up to 84% in sludge volume percentage depending on acid type and clarification conditions. Decreasing the volume percentage of the sludge facilitates acid handling as well as decreases the adherent water- soluble P205 leading to lower total P2O losses.

Jan 1, 2002

By Marie-Antoinette Dziurla, Barrie Johnson, Åsa Kolmert

Acidophilic bacteria are well known for their role in accelerating the oxidative dissolution of sulfide minds, such as pyrite. Other acidophiles, however, are able to catalyze dissimilatory reductive reactions. Bacteria that reduce ferric iron to ferrous, and sulfate to sulfide, were isolated from ARD-impacted environments and immobilised onto porous beads made of recycled glass. Column bioreactors containing colonized beads were constructed and peacolated with synthetic and actual ARD, and evaluated for their capacities to promote iron or sulfate reduction, and pH amelioration. Iron reduction did not require strictly anoxic conditions in bioreactors, and rates of up to 800 mg Fe3+ reduced/(l*day) were achieved, with a conversion efficiency of up to 98%. Using mixed populations of acidophilic fungi and iron-reducing bacteria, the bioreactors were capable of promoting iron reduction using paper pulp as sole carbon and energy source. Reduction of sulfate in pack bed bioreactors was observed with acidic wastewaters of pH 3 and above, though average rates of 300 mg sulfate reduced/(l*/day) were less than those recorded for circum-neutral pH systems. Bioremediation of ferric iron-rich ARD was assessed using coupled iron-reducing and sulfate reducing bioreactors.

Jan 1, 2000

By Norm Greenwald

The Environmental Protection Agency ("EPA") has been attempting to develop a federal regulatory program for mine waste under Subtitle D of the Resource Conservation and Recovery Act since 1986. Recent regulatory and legislative events are now bringing this goal closer to reality. This paper discusses the mining industry's perspective on a number of the issues currently being addressed at EPA's Policy Dialogue Committee and in Congressionally-sponsored negotiating sessions.

Jan 1, 1992

By M. J. Richards

Spontaneous combustion caused by the movement of air through the waste is a major problem. Combat methods attempt to exclude oxygen rich air, but little is known about airflow through the waste. The use of a tracer gas technique to monitor the flow of nitrogen from an injection hole during inertisation is described. Correlations are drawn between barometric pressure changes and the nitrogen entering the waste. As no information was obtained about airflow and oxidation zones, a second experiment was conducted to sample from the waste, but the results were inconclusive. A finite element method developed to model the pressure and airflow distribution, under steady state and nitrogen injection conditions is outlined

Jan 1, 1987

By N. N. Manu

In the Central African Copper Belt, sulfidization flotation is the standard practice for dolomitic copper oxide ores. It is a delicate process, and its plant application requires close control of the reagent addition. This paper presents the results of a thorough laboratory investigation. It features the monitoring, during sulfidization, of the pulp pH, the residual sulfide ion concentration and redox potential. Variables examined during the process were: retention times, sulfidizer additions, pH, collector type, dispersant dosage and reducing agent addition. Implications of the findings for plant application and process control are also briefly examined.

Jan 1, 1994

By Eugene F. Casey, William H. Hansmire, J. Ghaboussi, Randall L. Lentell, Harvey W. Parker

INTRODUCTION Construction of a major intercepting sewer in Brooklyn, New York involved tunneling in soil over several subway lines. In two instances the clearance between the subway and sewer was sufficiently close that concern was raised about the influence of the new construction. Prior to each critical crossing, analytical studies were performed which characterized the tunneling influence. It was demonstrated that with adjustments in construction procedures the crossings could be made without affecting the integrity of the subway linings. A comprehensive program of instrumentation and full-time monitoring was undertaken to ensure that any unforeseen adverse developments during crossing would be recognized. The successful crossings were subsequently made with minimal influence. Reported herein are the special construction conditions for the two crossings, the analytical simulation of behavior, and the results of monitoring on the subway linings. SEWER TUNNEL CONSTRUCTION AND EXISTING SUBWAYS The Red Hook Intercepting Sewer is a 2600 m (8600 ft) long tunnel which is part of a major water pollution control project in New York City. For clarity of nomenclature, the sewer is termed a 'tunnel' while the rapid transit structures are termed 'subways'. For routine construction, the tunnel was mined by hand with a 3.2 m (10 ft-5 in.)

Jan 1, 1981

By Rudolf E. Greuer

Modeling a mine ventilation system is a formidable mathematical problem requiring the solution of twice as many equations as there are airways with half of these being quadratic equations. The addition of a mine fire to the problem adds many more complexities. The U.S. Bureau of Mines and Michigan Technological University attacked this problem in stages. During the 1970's and 80's, a series of computer simulation programs were developed which offered progressively increasing levels of modeling capability and accuracy. The current version of this software, MFIRE 2.0, was released in 1993. This programs provides for full dynamic state mass flow-based modeling of a mine ventilation system, and includes natural ventilation, mechanical ventilation, air reversals and recirculation, methane and fire contaminant spread, and moisture condensation and evaporation in the mass flow and heat exchange calculations. This program is a useful tool for routine ventilation planning and can significantly improve mine safety by enabling detailed quantitative analysis for mine emergency preplanning. This paper reviews the evolution of the MFIRE program from its infancy as a simple digital network simulator replacing analog computers to the present version.

Jan 1, 1994

By Patti J. Best

The Southern Powder River Basin (SPRB) now commands 30% of the US utility, coal market due to the region's low mine production costs, competitive rail rates and low sulfur content. In 1997, production exceeded 240 Mt (265 million st). This was an in¬crease of 104 Mt (115 million st) since 1989 and 4.5 Mt (5 million st) above 1996. Continued growth is expected as the second phase of the Clean Air Act Amendments (CAAA) approaches. This growth will be the greatest in the southern part of the Basin where coal quality is higher. Coal characteristics SPRB coal is classified as subbituminous due to its low heating value and high moisture content. The coal is characterized by low sulfur and ash contents, low ash fusion temperatures and high reactivities. In 1997, the average heating content was 8,593 Btu/lb, with an average sulfur and ash content of 0.79 lbs S02/million [ ] Btu and 5.13%, respectively. The distinguishing characteristic of SPRB coal is its low sulfur content. Most SPRB coal contains less than 1.2 lbs S02/million Btu. This is the approximate definition of "compliance" coal for Phase II of the CA AA. Much of the coal, particularly in the southern part of the Basin, is referred to as "super-compliance" coal due to SO2 contents of between 0.4 and 0.7 lbs SO2/million Btu. The SPRB is divided into three geographic clusters based on coal quality. Mines located in the southern part produce coal with the lowest average sulfur content and highest heating content, almost 400

Jan 1, 1998

By B. Das

Most coals are susceptible to spontaneous heating which in turn creates problem to mining, storage and transportation of coal. It is impossible in actual practice o eliminate spontaneous heating but spontaneous combustion can effecively be controlled through a clear understanding of its mechanism and the factors affecting it. There are altogether six stages in the process of spontaneous combustion. This includes the water adsorption stage and six oxidation stages: chemi-sorption (upto 70°C), decomposition of peroxygens (70°C-150°C), oxy-coal formation (150°C-230°C), combustion initiation (230°C) and active combustion (> 230°C). Heat is produced in all these stages. On the other hand heat is also dissipated so that some equilibrium temperature is reached. If this temperature exceeds a certain critical value (generally about 70°C), coal oxidation may advance to spontaneous combustion. The major factors influencing spontaneous combustion of coal are: coal rank, maceral composition,, water, mineral matter, joints and fissures, seam depth and thickness, mine Layout, method of ventilation, etc. Susceptibility is high for low rank coals and generally decreases with increase in rank. Of the macerals, the exinites are generally most susceptible, the inertinites least and the vitrinites somewhere in between. Water plays a major role on the spontaneous heating of coal, assisting in someways and inhibiting in other. Unrecovered coal in the gob (generally in thick seams) is a major source of fire hazards and this is specially important in shallow mine. Proper design of mine ventilation system can substantially reduce the risk of mine fire. Panel layout and load transfer can affect the development of induced cracks which in turn influence spontaneous heating. Finally, the difference between the spontaneous heating of coal in a seam and that in storage or transportation is mainly due to the change in moistured content, air circulation through the coal and coal fragmentation. These aspects have been analyzed in this paper with a view o reducing the risk of spontaneous combustion.

Jan 1, 1986

By John J. Simmons

Federal and state regulations, in an effort to reduce acid rain, are becoming increasing more stringent regarding sulfur content of fossil fuels. Whereas coal from Illinois and Ohio contains between 1.5 and 37. sulfur, Wyoming has billions of tons of coal reserves containing less than O.5/% sulfur. However, much of Wyoming's coal is high in moisture, 25-30%, and low in energy, 8,200 to 8,900 BTU, vs. 10,500+ BTU for Illinois and Ohio Basin coals. Wyoming currently ships in excess of 130 million tons of coal to utilities as distant as Michigan, Wisconsin, Minnesota, Iowa, Nebraska, Louisiana, Oklahoma, and Texas. With freight charges ranging from $12.00-$20.00/ton, more than $1.5 billion a year is spent to transport water. A test shipment of more than 50,000 tons of Wyoming coal has recently been made from Mobil's Cabello Rojo Mine, south of Gillette, by Burlington Northern to the Robert's Bank British Columbia coal terminal for transloading and shipment to Taiwan Power Company. This coal assayed approximately 8,400 BTU/lb. and 277. moisture. Carbontec Energy Corporation feels the future availability of dried coal containing 11,000+ BTU could substantially enhance the potential export as well as the domestic market for Wyoming coal. Large and small utilities, along with industrial furnaces require tens of millions of tons of Wyoming, West Virginia, and other Eastern The federal government is encouraging the expenditure of hundreds of million of dollars by utilities to retrofit their boilers to allow them to burn higher sulfur coal. This program, if carried to completion, would cost many tens of billions of dollars, with the net result being high power costs sustained by the utilities. These costs will be passed on and paid for by the American consumer. A sensible alternative would be the burning of low sulfur coal by the utilities, without costly capital and operating expenditures. Carbontec Energy feels the successful operation of a Carbondry Coal Drying Plant in Wyoming will be the forerunner to other similar and larger operations in the State. CARBONTEC RESEARCH The activities of Carbontec's personnel to develop a viable process to dry sub-bituminous and lignite coal goes back some 14 years; in fact, for some of us it goes back to 1962 when we were involved in a program under which lignite coal from Truax Trayer's Velva mine was placed in low sulfur coal, which are burned alone or blended with high sulfur, Midwestern coal. Carbontec believes that a high BTU. reasonably priced, shippable coal fuel produced in Wyoming and delivered at costs competitive with Eastern low sulfur coal, could offer substantial benefits to Wyoming coal producers, utility customers, and to the State of Wyoming.

Jan 1, 1989

By K. A. Natarajan, M. K. Yelloji Rao

Significance of grinding media wear and its effect on chalcopyrite flotation are discussed. Laboratory marked ball wear tests were conducted grinding chalcopyrite ore and quartzite dry, wet, and with collector added during grinding. The effects of oxygen and nitrogen on ball wear were evaluated by the addition of chalcopyrite mineral while grinding quartzite. The effect of dry and wet grinding on chalcopyrite flotation was also studied. Results show abrasive wear is greater in quartzite grinding than in grinding chalcopyrite. Oxygen increases the corrosive wear of high carbon low alloy steel balls in the presence of chalcopyrite ore. Chalcopyrite flotation was retarded due to wet grinding in the presence of oxygen. Though collector reagent increased the media wear, it improved the flotation of chalcopyrite. Probable electrochemical reactions encountered in a grinding mill are outlined.

Jan 1, 1991

By Mark H. Johns

Leaching of waste material at Kennecott's Chino Mines Division at Santa Rita, New Mexico, has been accompanied by increasing difficulty in circulating leach solutions through the dumps. As a means of recognizing existing problems and considering alternative applications of the leaching concept, a leaching research program was proposed which could be applied to a specific, typical waste dump. Conclusions derived from the area could then be applied to other leaching areas at Chino. Associated with the program was an evaluation of the physical characteristics of the area using Chino's drilling and radiation logging techniques.

Jan 1, 1970

By S. K. Kawatra, T. C. Eisele

Production of highly-cleaned coal for advanced utilization schemes requires close control of the coal ash content at very low levels. For this purpose, a sensitive, low-cost, robust on-stream ash analyzer is needed. The development of such an instrument based on x-ray backscatter and fluorescence is described, including features to improve its sensitivity at low ash levels. The performance of the resulting device in testing a real coal sample is discussed.

Jan 1, 1990

By P. M. Keyser

Column flotation continues to make inroads into applications traditionally dominated by mechanical flotation cells. For example, columns are becoming more visible as rougher flotation devices. At Royal Mountain King Mine in California, two 2.9 m (9.5 ft) diameter columns are used for rougher flotation of carbon from a gold ore (Orlich et al, 1992). In addition, work performed at BRGM in France demonstrated the superiority of column flotation over mechanical flotation with respect to design of new plants (Morizot et al, 1991). With the mounting evidence, columns can succeed in any flotation application. The primary reasons for this acceptance of columns are a general improvement in design, scale-up and operation as well as improvements in sparger design and performance. With these advances, the full benefits of column flotation can be realized. The benefits of properly designed, aerated and operated flotation columns include: ? Lower Capital Costs ? Reduced Operating Costs ? Fewer Processing Stages ? Improved Metallurgical Performance

Jan 1, 1993

By B. Mishra, A. Staley, D. Kirkpatrick

The major waste product of the alkaline extraction of alumina from bauxite (Bayer Process) is known as red mud. Approximately one ton of red mud is produced for every two tons of bauxite mined. The red mud produced from Jamaican bauxite is rich in hematite, alumina and titanium oxide. It has been shown that more than 90% (by weight) alumina can be recovered from red mud by soda ash sintering and caustic leaching. Hematite can be carbothermically reduced with a degree of metallization of more than 94%, resulting in attempts, for magnetic separation. These separations are desirable because there are no waste products generated. Consequently, there is an opportunity for complete utilization of the waste material. Conversely, the preseparated material could be charged through the tuyeres in an iron blast furnace, or it could be smelted to produce pig iron. If smelted, the concentration of titanium oxide in the slag would be high enough to justify its recovery by an established acid-leach process. This paper describes the results of alumina recovery and the plans for titanium oxide recovery from red-mud. In addition, the situation of ongoing efforts in iron extraction, particularly, the method of magnetic separation of the reduced material. The problems associated with the use of reduced red mud as an alternative to direct-reduced iron (DRI) is also discussed. A critical assessment of the recovery sequence chosen for the products is described based on economics. Key words: Red mud, Waste product utilization, Alumina recovery, Titanium oxide, Iron

Jan 1, 2003

By T. M. Barton

Coal mine bumps the violent failures of over-stressed coal', present a safety hazard to miners when mining is conducted in deep, bump prone coal mines. Two different longwall gate entry systems were evaluated in a Southern Appalachian coal mine located in the Pocahontas No. 3 Coalbed under approximately 610 m of overburden which included a massive sandstone member. Both gate entry systems employed a center abutment pillar flanked by yield pillars. The original design employed a 24.4 m square abutment pillar' while the new design employed a 36.6 by 54.9 m' abutment pillar. Rock mechanics instrumentation data analysis and in-mine observations indicated that this increase in abutment pillar size significantly decreased bump potential. The new design in worse case conditions increased effective bearing area 62 pct with only a 9 pct increase in gate entry system width and eliminated face bumps that wer7 experienced with the original gate entry design.

Jan 1, 1991