Search Documents

By B. J. Arnold

Utility coal specifications usually contain a requirement for a maximum moisture content in order to prevent coal handling problems and to minimize evaporative losses in the boiler. As most coal cleaning processes are water-based, dewatering and sometimes drying steps are required to meet moisture specifications. Screens are often used for dewatering, with centrifuges and filters used to further reduce moisture in many cases. Algorithms to predict the performance of screens were developed for the Coal Cleaning Simulator running under Aspen Plus during a project sponsored by the U.S. Department of Energy and the Electric Power Research Institute. These algorithms include calculations for the size separation and a calculation for moisture content of the oversize product based on particle size and specific gravity distribution. This paper discusses the algorithm for predicting the moisture content of coal dewatered by screens.

Jan 1, 1997

By Bjørn Nilsen

"INTRODUCTION/BACKGROUND Weakness zones or faults containing clay-rich gouge represent one of the most challenging rock mass conditions to be encountered during tunneling. In Norway, such conditions count for a large part of the rock support costs, and in cases where the rock support has been insufficient, serious instability and cave-in have in many cases been the result. Most commonly, such cave-in has occurred after water filling of hydropower tunnels, but in some cases it has also occurred in tunnels under excavation and in completed “dry” tunnels. To avoid instability, two important requirements have to be fulfilled: 1) The location of the weakness zone and its character have to be identified in time. 2) The rock support has to be sufficient to withstand the loading caused by the zone. An incident which really brought the problems related to swelling clay into focus was the cave-in at the Hanekleiv road tunnel in 2006. Here, rock fall from the roof as shown in Figure 1 occurred unexpectedly about 10 years after the tunnel was completed. Fortunately this happened at a time with very little traffic, and nobody was injured. This incident emphasized the significance of the issue of swelling clay, although it was found to be caused also by gravitational collapse of the clay-rich gouge material of the weakness zone, and not related to swelling only (Nilsen et al. 2007).In this paper, main focus will be on discussing the characteristic features of swelling clay, test procedures which are being used for characterizing swelling clay, and the reliability of the results from testing for use in support evaluation and design in conditions with swelling clay. It is generally well known that swelling clay may cause considerable pressure on support elements, but quantifying this pressure for reliable analysis and design of rock support is still a great challenge."

Jan 1, 2016

"Above ground, elevated belt conveyors that span more than 200 m (656 ft) between support points can cross valleys, rivers, forests and buildings with a minimal footprint. The cable bridge conveyor (CBC) is a new type of suspension bridge based belt conveyor system that has long spans between support points. It combines a typical belt conveyor and an improved simple suspension bridge to form a conveyor bridge. The improved simple suspension bridge places a widened bridge deck directly on suspended cables, without the need for high truss towers. The benefits include reduced cost and increase aerodynamic stability compared to conventional suspension bridges. The CBC’s compatibility with current belt conveyors allows versatility in application.A belt conveyor is a ubiquitous material handling system. Conveyors can be placed directly on ground or elevated above ground by support structures. Considerations of cost, design, environment, civil work, safety and process requirements are all factors in choosing the ground-based or elevated conveyors (Zhang, 2014). The ground-based conveyor has the lowest structural cost when the conveyor is placed on an existing road. Maintenance access is easy and straightforward. Compared to the groundbased conveyor, the elevated conveyor can cross existing buildings and structures, give passage to traffic beneath the conveyor, has a smaller footprint and requires less civil work to pass mountainous areas. The drawback of the elevated conveyor is higher structural cost, which can be compared with savings in civil work and other benefits. Conventional elevated conveyors are supported by rigid truss-type structures, with a typical span of 15 to 25 m (50 to 82 ft) between concrete support bents or steel trestles. Triangular truss, using steel pipes instead of hot rolled steel sections, is more efficient. The typical span of a triangular truss-supported conveyor is around 30 to 40 m (100 to 130 ft), while the weight is about 10 percent less than conventional box truss with a shorter span (Jennings, 2013).Long-span elevated structures based on suspension bridge is another step forward in increasing the distance between support bents, reaching 100 to 400 m (330 to 1,312 ft) and beyond. The wide distance between the support points of an elevated conveyor offers unique benefits. The conveyor can cross rivers, valleys, highways, forests and other obstacles with minimal footprint and reduced civil work. The versatility from long-span conveyors makes bulk material transportation over previously impossible terrains now a feasible option."

Jan 1, 2014

By MARK J. VANARELLI

Estimating groundwater inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies for estimating steady-state groundwater inflows into deep rock tunnels. The case studies included the Chattahoochee and Nancy Creek tunnels. In this paper, statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations. A semi-empirical procedure was utilized for estimating groundwater inflows into these deep rock tunnels. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels which exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semi-empirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Packer test data plotted in histograms were observed in all cases to be log-normally distributed for the radial flow condition. Modeling using Monte Carlo simulations was observed to be an effective tool for removing irregularities in the distribution of the data and incorporating high-end permeability data to derive reasonable groundwater inflow estimates.

Jun 13, 2021

By B. M. Kunar, C. S. N. Murthy, B. Rao K

Rock particle size has a very important significance in the mining industry, starting from blasting till the mineral processing. The present study was carried out to understand the particle size distribution in various sieves after conducting the ball milling process. The time of the grinding process was varied at different intervals. It was observed that 80% of the particles of both granite and marble rock samples passed through the 4800 μm sieve when subjected to grinding time of 40 minutes. Also, it was observed the number of particles that were retained in the smallest sieve of <75 μm was higher in the case of granite sample when compared to a marble sample. INTRODUCTION India is a major exporter of granite and marble stones. The major use of marbles and granites are constructing walls and floors. There are several machining processes that are applied before it is used as floors and walls. During this process, wastes are produced these wastes are used in various ways. These include use of powders for clay products (Segadães, Carvalho, & Acchar, 2005), as an additive in cement production (Aruntaş, Gürü, Dayi, & Tekin, 2010), to enhance the properties of brick ceramics (Saboya, Xavier, & Alexandre, 2007), in constructing bricks (Bilgin et al., 2012) and as an additive in concretes (Aliabdo, Abd Elmoaty, & Auda, 2014). Usually, the powder form of marble and granites are used as an additive in the above-mentioned applications. Powders of marble and granite are obtained through the grinding process. One such process of grinding is the ball milling process. In the ball milling process, a quantity of samples along with the charge quantity consisting of steel ball is subjected to a grinding process within a closed chamber as shown in Fig. 1. An even particle size can be obtained through sieving the material after subjecting it to grinding. The present study is planned to understand the particle size distribution in various sieves due to varying time and charge quantity in the experiment. Only time was varied to understand the amount of particle distribution in the case of granite and marble rock samples and a comparison is drawn. A statistical model was developed for marble rock specimen considering the data obtained by varying time and charge quantity in the ball mill experiment.

Jan 1, 2019

By Ernest E. Thurlow

The Geology Division of Northern Pacific Railway Company has adapted to its exploration efforts field procedures for geochemical sampling and semi-quantitative analysis which have been developed through research by the U. S. Geological Survey. The sampling is done in conjunction with reconnaissance geologic mapping on aerial photographs or during field checking of maps which have been prepared largely by photogeologic interpretation.. Stream sediment or soil samples are taken and readily soluble combined heavy metals are extracted with ammonium citrate followed by colorimetric titration with dithizone at the sample site. The effectiveness of this approach has been demonstrated both in positive and negative results, thereby assisting in the elimination of large areas of land from further immediate attention and in providing targets for followup exploration. An occasional sample is submitted for spectrographic analysis as a check on the possible presence of other elements of economic significance. Field laboratory procedures are also being implemented for determining molybdenum, mercury, and other metals which may be valuable in themselves or useful as pathfinder elements in outlining mineralized areas. A lead-zinc occurrence in Oregon and a copper deposit in Montana were readily detected and outlined by stream sediment and soil sampling and a heavy metal anomaly that lacks obvious interpretation has been found in northwestern Montana. Detailed mapping and additional sampling are followed by other exploration techniques if warranted.

Jan 1, 1964

By Bo-Hyun Kim, Mark K. Larson

"Bumps remain a critical safety concern in underground coal mining, despite significant advancements in engineering controls. These events occur when relatively high stresses in a coal pillar in conjunction with low confinement exceed the pillar’s critical capacity, causing the pillar to rupture without warning. Floor failure often occurs and can be an indicator of bump risk, as it is strongly associated with brittle failure known as spalling under a lower confinement. Significant floor heave at a western U.S. coal mine has been observed where the pillar width in a three-entry gate road system was 53 m, while no significant floor heave was observed where the pillar width in another gate road system was 22 m. This phenomenon was widely reported in the region and at another mine in another western coal field it has been reported that larger pillars are always associated with floor heave. In this study, a spalling model based on the S-Shaped brittle failure criterion and associated with the anisotropic characteristics of the materials was used in FLAC3D. The observed floor heave phenomenon associated with the larger pillars was demonstrated using this modeling approach.INTRODUCTIONFloor failure in a coal mines often inhibits longwall mining operation, as large displacement of floor strata, known as floor heave, interferes with travel, access, ventilation, and equipment operation. Aggson (USBM 1978) investigated floor heave in West Virginia where underclay is relatively strong and high horizontal stress is present. It was reported that the failure mode is mainly by buckling rather than by plastic flow.This study was developed as part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to better understand rock mass behavior in longwall coal mines in highly stressed, bump-prone ground. More specifically, this study attempts to explain through numerical models small energy releases in the form of floor heave. The authors believe that brittle rock failure is associated with both floor heave and some bump mechanisms, if not directly involved in their cause."

Jan 1, 2019

By L. Yuan, J. H. Rowland, D. Bahrami, R. Thomas

Blasting is the main method of production in many non-coal underground mining operations and produces multiple toxic gases as a result. The Mine Safety and Health Administration (MSHA) requires mine operators to measure the level of toxic gases in mines as frequently as necessary to ensure they are below regulatory safety limits. The current practice uses portable gas monitors to check the concentrations of toxic gases after a fixed post-blast time. This paper studies the application of a gas monitoring system in the return entry of a limestone mine to determine a safe re-entry time. The National Institute for Occupational Safety and Health (NIOSH) conducted such a monitoring program in a limestone mine from September 2016 through May 2018. NIOSH/PMRD (Pittsburgh Mining Research Division) is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions. This study showed that the use of gas monitoring in the return air can be a useful tool at the mine operator’s disposal to detect and reduce the risk of hazardous conditions and also to reliably estimate the re-entry time.

By B. C. Haydon

Manganese silver ores are well known to be refractory towards cyanidation. Various processes have been suggested for improving the amenability of these ores. A sulfurous acid pre-leach is one such process. This paper traces the development and implementation of the sulfurous acid pre-leach process for the retreatment of manganese silver tailings at Tonopah, Nevada. An account of the test work program is presented, followed by a description of the operating plant and specimen metallurgical performance. The paper also summarizes the history of the Tonopah tailings, their mineralogy and makes reference to previous application of the sulfurous acid pre-leach process.

Jan 1, 1984

By William G. Pariseau

The purpose of this paper is to present a discussion of the various approaches that can be utilized in the study of mine subsidence phenomena. Attention is focused upon the rational selection and use of laboratory models. Broadly interpreted, mine subsidence is the deformation of the rock mass enclosing the mine. Depending upon a number of factors, the movement of the subsiding rock mass may be such as to disrupt gas and water lines or other buried utilities, to damage surface structures such as buildings and bridges, to dislocate streams, roads, and rail lines, to aggravate acid mine drainage and fire problems, and to generally mar the landscape. It is clearly a problem that no mine manager can safely ignore. It is also a problem that will grow with the general population increase. In the following, a summary review of past and present approaches to subsidence studies is given. The possibilities of duplicating subsidence phenomena in laboratory models are examined, and an analysis of a particular type of model is presented. Some preliminary results obtained from a model of the particular type analyzed are then discussed.

Jan 1, 1968

By B. W. Cavender

The operating lifetime, or production rate, selected for a mining project is among the most important factors influencing the design and ultimate economic success of the project. An incorrectly-determined lifetime can lead to the erroneous rejection of projects as uneconomic as well as the suboptimal exploitation of producing properties. This paper examines the calculation of the optimal lifetime using both traditional discounted cash flow and recently-proposed option pricing techniques. Using each method, the production rate is determined as that rate at which the net present value of the project is maximized.

Jan 1, 1992

By M. Z. Rashad

The purpose of this work is to determine the influence of sample length or size on the value of variance (Semivariogram) to select the suitable length that is required to the geostatistical computations of ore evaluation. Three cases in Ghorabi Iron Ore were studied. The first one was on the iron fraction (Fe%) at which the semivariogram gave an evidence to good continuity of the fraction in the ore. In this case, the length of sample has not important influence. The second case was for the Mn% component of the same area where the semivariogram has a nugget effect. The selected length for this case was 4 meters. The Cl% fraction of the ore was the third case where the anisotropic phenomena was appeared and the suitable length is 3 meters.

Jan 1, 1992

By L. Lichty, R Bhappu, R. Rowan, G. Ramadorai

Treatment of refractory gold ores containing arsenic have always presented a major problem in their processing to recover the contained precious metal values. The major difficulties are concerned with lower recoveries, production of hazardous fumes, effluents and residues. Because of&apos;these arsenic related problems, many otherwise economically attractive precious metal deposits and dumps all over the world are not exploited. In recent years, treatment processee for refractory gold ores and concentrates have been explored and a few commercial operations employing roasting or pressure leaching have resulted. Roasting has limitations due to environmental constraints related to off gases. Pressure leaching involving high temperatures (180% to 200%) and pressures (400 psi) is accompanied by high capital and operating costs. An alternate route to roasting for treating pyrite and arsenopyrite ores and concentrates ia the "lime-oxygen hydromet" process carried out at a moderate temperature (100%) and pressure (100 psi). A simplified process for treating such arsenic containing ores and concentrates utilizing low temperature and pressure oxidation is presented. This low cost treatment with compressed air and lime renders arsenic as an inert component in the residue, meeting all the requirements of the EPA Toxicity Test. The precious metal values are then extracted from the autoclaved residue by standard cyanidation. This paper discusses this new development.

Jan 1, 1990

By Osvaldo A. Bascur

Most mining and metallurgical plants have developed predictive maintenance policies based on statistical analysis and special techniques, like vibration analysis, oil and lube analysis for critical equipment. Process control strategies have also been installed in several metallurgical sites. These control strategies require instrumentation maintenance from local personnel. The availability of real time and process history to identify the most critical part of the processing system from mechanical integrity is a must for global plant optimization. Specialized performance control monitoring algorithms are required to justify their existence and contribution to the bottom line. Emerging technologies are combining these techniques into a single total plant system. Tools are required to assist in troubleshooting and adapting these process control instruments and strategies. The key is the plant equipment and process control availability and utilization rather than just maintenance.

Jan 1, 1997

By H. Dho

The role of sodium silicate in the anionic flotation of a Florida phosphate ore was investigated using laboratory continuous flotation tests, frothability tests and SEM observations. In the absence of sodium silicate, Ca++ promoted the unwanted activation of quartz by forming calcium bearing precipitates. The addition of sodium silicate enhanced the flotation efficiency through: (1) the removal of impurity minerals and calcium-bearing. precipitates from quartz surfaces by dispersion, (2) drier and more persistent froths stabilized by oily droplets containing calcium silicate precipitates, and (3) higher specific flotation rates of phosphate relative to quartz, leading to faster flotation rates and increased selectivity of separation.

Jan 1, 1990

By R. R. Sacrison

The Barrick Mercur Gold Mine lies in the Oquirrh Mountains of northern Utah. Limestone, sandstone, shale, and chert are the predominant rock types being mined. Recent expansion has encountered rhyolite. Lithology and structural attitudes control most mechanical behavior. Slope steepening, mine planning, and site selection are presented as means by which geological engineering has contributed to the economics of the operation. Geomechanics investments of approximately $700,000 have resulted in cost savings or additional production worth over $16,000,000.

Jan 1, 1990

By J. L. Parks

Designs, installation procedures, and performance characteristics of martensitic cast steel concaves are reviewed. Longer wear life, fewer pieces to install, and eliminating the need to scarf joints are the principal benefits of using martensitic steel to replace austenitic 12% Mn (Hadfield&apos;s) steel, the traditional concave material for large gyratory crushers. Installation procedures that reduce the risk of breakage are described. Operating practices that affect concave performance are also discussed.

Jan 1, 1992

By Satya Harpalani

An investigation was carried out to study the microscopic structure of coal in order to understand the phenomenon of methane migration. A Scanning Electron Microscope (SEH) was used to study the surface and pore structure of bituminous coal taken from an underground mine. Micrographs obtained showed the highly porous nature of coal which explains the large quantities of gases that remain within the pores in the compressed and adsorbed forms. These micrographs further showed that most of the pores within the coal matrix are the &apos;dead-end&apos; type and do not contribute much towards the flow of gas. The most important finding was that solid coal has a network of cracks and fractures indicating that it is these cracks that are primarily responsible for the gas flow, rather than the pores. The size and distribution of the pores within coal influence the capacity of coal to retain methane but movement of the gas molecules is the responsibility of the microfractures. Any mathematical modeling to simulate gas flow through coal must take this into account. For purposes of modeling, the structure of coal can be considered to have dual porosity. First, the gas molecules are released from the pores and there is a gradual migration towards the fractures. Once the gas reaches the fractures, its movement is eased greatly along these fractures.

Jan 1, 1987

By Martin B. Hudson, John Yao, Matthew R. Crow, Yiming Sun, John T. Waggoner, Roozbeh Geraili Mikola

"The Wilshire Grand redevelopment project in downtown Los Angeles includes construction of a new 73-story tower. Construction required excavation up to 93 feet deep (28 m). The south side of the excavation, up to 57 feet deep (17 m), required placement of shoring within about 6 to 10 feet (1.8 to 3.0 m) horizontally away from a 400-foot-long (122 m) section of one of the existing Los Angeles Metro Red Line twin subway tunnels. These tunnels were constructed using a 22-foot-diameter (6.7 m) digger shield, and were initially supported with expanded, precast concrete segments, with final cast-in-place reinforced concrete lining. The temporary shoring system for the deep excavation consisted of soldier piles generally spaced at 8 feet (2.4 m) on center with multiple levels of tieback anchors extending above the subway tunnels. The lowest level of bracing consisted of rakers supporting walers attached to the soldier beams because installation of tieback anchors at that level would conflict with the tunnels. Numerical analyses were performed to predict tunnel movement caused by the excavation and its effects on the train operations. This paper describes the numerical modeling, tunnel and geotechnical instrumentation and monitoring program, and comparison of the computed and observed tunnel responses to the deep excavation and tower construction. With increasing urban redevelopment in major cities, the project is a valuable case history for excavation adjacent to existing tunnels. INTRODUCTION The Wilshire Grand redevelopment project includes the demolition of a 16-story hotel built in the early 1950s and the construction of a new 73-story tower in downtown Los Angeles (LA) that will be the tallest building in the western United States. The project site is situated on approximately 2.7 acres (1.1 Ha) of land bounded by Figueroa Street to the east, Wilshire Boulevard to the north, Francisco Street to the west, and 7th Street to the south (see Figure 1a). The new tower is being constructed by Turner Construction for Hanjin International Corporation. Construction of the basement and foundation of the new tower required excavation up to 93 feet (28 m) deep. Shoring was designed by Cefali & Associates and installed by Malcolm Drilling Company. Along 7th Street, an excavation up to 57 feet (17 m) deep required shoring to be installed within about 6 to 10 feet (1.8 to 3.0 m) horizontally from an existing 400-foot long (122 m) section of one of the LA Metro Red Line subway tunnels (see Figure 1b). The tunnels, extending from the 7th/Metro Station to the Westlake-MacArthur Station, were constructed in the late 1980s and early 1990s with an excavated diameter of approximately 22 feet (6.7 m). They were initially supported with expanded, precast concrete segments with a final cast-in-place reinforced concrete lining. The existing hotel was demolished in 2012 and 2013, with shoring installation and excavation for the new basement occurring as the demolition occurred. At the time of writing, January 2016, the structure of the building adjacent to the tunnels is largely complete."

Jan 1, 2016

By C. Newman, R. C. Ray

Originated and developed in the civil tunneling industry, the Ground Reaction Curve (GRC) has provided a robust methodology for evaluating and designing ground support in both tunnels and underground mining scenarios. This paper presents a preliminary assessment in the utilization of the GRC concept for the evaluation and design of the pillar-support system with respect to overburden stress and displacement. This initial assessment will be based on and backed by past research on this topic. Underground mine instrumentation is planned for a longwall mine in the Appalachian coal field based on the research and findings in this paper to support the postulated hypothesis. INTRODUCTION Since the early 1970’s, the mining industry has evaluated the structural stability of a pillar by dividing an approximated pillar load by an approximated pillar strength. While this design methodology has served the industry well in the past, as modern mining operations continue to develop in more complex geological and geometric conditions coupled with market economics, industry professionals are in dire need of a modified stability assessment approach which considers both the stress condition and material displacements. Within the civil tunneling industry, the GRC approach has been successfully utilized in designing underground support measures that enhance the stability of an underground excavation. Through the incorporation of current industry knowledge and understanding of ground and support behaviors this paper looks to investigate into preliminary assessment for the development of a Modified Support Response Method (MSRM) to further improve the analysis of local and global underground stability. CURRENT PILLAR DESIGN METHODS AND THEIR LIMITATIONS Globally, multiple pillar design methods have been utilized in the design of underground excavations. Each of these methods approaches the calculation of pillar stability a little differently with respect to material properties, underground geometries and stress conditions. Analytical solutions can be used to determine the strength of homogeneous materials like concrete, but not in case of non-homogeneous and non-isotropic mineral deposits in a mine. These equations are often derived using empirical methods. Pillar strength is defined as the maximum resistance of a pillar to axial loading (Brady & Brown, 1985). The strength of mine pillars is typically estimated through indirect methods. In the past, researchers have correlated the strength of a given size and width of a rock specimen to the strength of a mine pillar. The first study on the effect of geometry on rock strength was done by (Bauschiger, 1876) on Swiss sandstone samples. Since then several empirical equations to determine pillar strength had been published by many researchers like (Bunting, 1911), (Griffith & Conner, 1912), (Greenwald, Howarth, & Hartmann, 1939), (Holland & Gaddy, 1957), (Evana, Pomeroy, & Berenbaum, 1961) and (Holland C. , 1964).

Jan 1, 2019