Search Documents

By L. H. McGuire

Many coal beds in the State of Washington, pitching as much as 90°, offer unusual mining conditions. This paper describes methods and safe practices of mechanized mining in pitching bituminous-coal beds that have attracted the attention of mining people from most of the coal-producing countries of the world. The development and use of continuous miners as part of the mechanized program apply particularly to the Roslyn-Cle Elum coalfield, Kittitas County, Wash. All three mines now operating in the field use continuous miners and during 1957 furnished 72 percent of the State's total coal production. Mining operations are now conducted in three coal beds of the Roslyn-Cle Elum field. The coal measures range from 3-1/2 to 20 feet in thickness and vary in dip from 5° to 45° in the localities where the coal is mined. Some safety measures adopted by-the principal operating company in the field during the past 30 years of mechanized mining follow: Use of only permissible electrical or compressed-air-operated equipment on other than intake air; providing and using an explosion gallery to test repaired permissible electrical equipment before taking it underground; use of only compressed-air-operated drill augers in preference to permissible

Jan 1, 1959

By Warren D. Stanford Stanford

Introduction The Sleeper mine is a near-surface gold mine located in a remote area 56 km (35 air miles) northwest of Winnemucca, NV (Fig. 1). The deposit was discovered in 1984 by an Amax exploration geologist. Favorable drilling results led to feasibility studies and metallurgical testwork. Final evaluation of the mine potential proceeded very quickly. The project received Amax board approval in July 1985. Eight months later, the process plant was fully operational. The first gold ($1 million) was shipped one month later, in March 1986. Total plant capital was $27 million. Payback was achieved in six months. The Sleeper mine was expected to produce 1.6 t (53,000 oz) of gold and 1.3 t (41,000 oz) of silver annually. However, the ore body exceeded all expectations. Production for the first 10 months of operation amounted to 4 t (128,000 oz) of gold and 2.9 t (94,000 oz) of silver. Direct cash operating costs are in the $1.77/g ($55 per oz) range. Amax is actively conducting exploration nearby for additional reserves to extend the mine's life. (See update on page 242.) Geology The Sleeper gold deposit is located on the northwestern flank of the Slumbering Hills and in the Awakening Mining District. Rocks exposed in the vicinity of the deposit are interbedded siltstones, sandstones, and limestones of Triassic age. They are overlain by latite lava flows and tuffs of Tertiary age. Dikes and sills of latite and andesite intrude the sedimentary rocks. Quaternary deposits of mostly sand with minor gravel and clay cover a pediment containing the gold deposit. The sedimentary and volcanic rock units have been transsected and offset by extensive north- northeast trending faults and less abundant northwest trending faults. Both fault systems fractured and prepared the ground for subsequent invasions of mineral-bearing hot spring geothermal waters. The hot spring systems produced widespread hydrothermal alteration and gold mineralization at silicified centers near feeder fault structures. The deposit is hosted by siltstone and latite that have been hydrothermally brecciated. The main breccia is elongated north-northeasterly. The hydrothermal breccia zones appear to dip steeply to the west. Gold mineralization consists of native gold and electrum deposited in two or more high-grade quartz-breccia veins. Lower grade gold mineralization occurs

Jan 4, 1987

By R. J. Sweigard

One possible alternative for disposal of flue gas desulfurization (FGD) by-products is use as backfilling support material in highwall mine adits. The finite element method was used to analyze the variation of stresses and displacements within and around a highwall adit backfilled with FGD materials. The engineering properties of the rock material and the optimum mix proportioning of the FGD materials were obtained from laboratory tests. Finite element analyses show that, for the case in question, the roof displacement would decrease about 48 percent and the peak stress could be decreased about 58 percent. The study indicates that fairly weak FGD materials can eventually lead to stability of backfilled highwall adits.

Jan 1, 1996

By H. S. Castro

The by-product molybdenite technology in Chile is reviewed. Flowsheets, reagents and some operation features for the actual six Chilean moly plants(Chuquicamata, El Teniente, El Salvador, Andina, Las Tortolas and Pelambres), are presented. The chemical and physicochemical factors involved in the depression of copper and iron sulfides during the selective flotation of molybdenite, with sodium sulfide, sodium sulfhydrate, anamol-D and LR-744, are discussed. Advances in technology to solve problems of excess of lime (precipitation with sulfuric acid); excess of residual flotation reagents (activated carbon and kerosene); and optimization of depressant consumption (Eh control, nitrogen and low-oxygen air), are discussed.

Jan 1, 1998

By Perry N. Halstead

The primary objective of the structural geology portion of the Kennecott Copper Corporation-U. S. Bureau of Mines Pit Slope Stability Study was to determine the attitude, geometry, and spatial distribution of geologic structures of the west wall of the Kimbley Pit for use in designing a maximum stable slope for the pit. A corollary objective was to develop and refine techniques for collecting and analyzing geologic structural data with emphasis on numerical methods that could be integrated with other aspects of pit design. Surface mapping techniques used were a modification of conventional joint set mapping and a detailed linear sampling method. For subsurface investigations both oriented core and a borehole camera were used. It was determined that the major faults in the area were favorably oriented for mining a steep stable slope. The jointing or natural fracturing, although complex, was not random in attitude and consisted of several persistent fracture sets and a number of secondary sets. The attitude of the persistent fracture sets was favorable for steeper slope angles, and these attitudes were used in the design considerations. There was no significant difference between the attitude of the fracture sets determined from the former and new slope face.

Jan 1, 1968

By Z. Rogovin

In order to develop more accurate procedures for scale-up and design of semi-autogenous-grinding mills through detailed mathematical models, a better understanding of the charge motion and rock/ball segregation is needed. To achieve this a 0.61 m (2.0 ft) diameter x 0.305 m (1.0 ft) length plexiglas mill was constructed as a scale model of a commercial SAG mill. Rock motion in the rotating mill was simulated using various sizes of ceramic balls. Quantitative measurements of dynamic angle of repose, water and slurry motion, holdup and size segregation of the charge were taken. In addition, a video-presentaiton (available to the public) was prepared to elucidate charge and water motion at various mill speeds, charge volumes, rock size distribution and flow rates.

Jan 1, 1985

By S. S. Peng

A well designed mining plan is one which minimizes the cost and the mining induced problems and maximizes the recovery of the coal reserve. In order to minimize the negative effects on surface structures caused by ground subsidence process due to underground mining activities, two kinds of practices are commonly employed by the mine operators. One is the support techniques which leaves an area of coal un-mined or partially mined beneath the structure to be supported. The other is the protection techniques which protect the structure when it is subsiding with ground taking advantage of the ground subsidence process (Luo et al., 1992). In designing the supporting techniques, the only currently available method in the U.S. is the one stated in the Pennsylvania Underground Coal Mining Rules (1985). However; The size of the support area designed by this method will be excessively large resulting in wasteful use of coal reserve when the overburden depth is more than 350 ft. A more scientific method is proposed in this paper for de-signing the support area. This method is based on a large amount of subsidence data collected throughout a number of major U.S. coal fields and the authors' experience with monitoring and protecting surface structures undermined by longwall panels. It considers the critical deformation in-dices that a structure can tolerate, and depth and height of underground extraction. The support area designed by this new method will not only assure the safety of the structure to be supported but also maximize the extraction of the coal reserve.

Jan 1, 1993

By G. S. Dobby

High-intensity wet magnetic separators have been successfully introduced into the mineral processing field over the past ten to fifteen years, due largely to rapid advancements in magnet design. Wet magnetic separation, until recent years, was applied solely to the concentration of minerals of high magnetic susceptibility, such as magnetite, at relatively coarse sizes. Now, however, high-intensity separators are capable of treating weakly paramagnetic minerals and have extended the range of treatable particle size down to about one micrometre(1,2). . One of the more recent-high-intensity separators developed is the Kolm¬Marston Marston type high-gradient magnetic separator (HGMS) (3,4) It consists basically of an iron-clad solenoid surrounding a matrix material - a fine, ferromagnetic steel wool or expanded metal lath. A schematic diagram of the device is shown in Figure 1. Large, highly localized, pertebations of the magnetic field are created by the ferromagnetic matrix. It is these field gradients that are instrumental in developing large magnetic forces which act on the mineral particles. Operation of the separator is simple. Slurried sample is fed through the matrix and, depending upon the mineral parameters of particle size and magnetic susceptibility and. the operating parameters of flow rate, field strength and feed weight, some particles will be attracted to and adhere to the magnetized matrix, while the others will flow through the matrix. The separation is completed by later removing the background magnetic field and flushing the captured mineral particles into a separate container. The process can also be applied on a continuous basis (S).

Jan 1, 1977

By J. Y. Hwang

Alunite has been utilized as raw materials for producing alumina and potassium sulfate fertilizer in Russia for many years. In the United States, this mineral has not been commercially processed though reserves of 5 to 10 billion tons of alunite ore have been estimated. Major constituents of these ores include quartz and alunite. The minerals are finely intergrown and liberation occurs below 10 microns. Adequate separation techniques for such fine particles have not been developed. A new method for the beneficiation of alunite ore is proposed in this study. 'Ibis method utilizes a small amount of fine magnetite upon which the liberated quartz is selectively flocculated. The co-flocculated magnetite and quartz are then separated from the alunite in a high gradient magnetic separator. Clean products, e.g. an alunite concentrate of 90% grade with 80% recovery, has been obtained from an Utah ore. Techniques for the selective co-flocculation of magnetite and quartz, the separation of the carried quartz, and the recovery of magnetite after separation are discussed.

Jan 1, 1985

By V. Gall

The three-dimensional finite element technique combined with the progressive failure approach was utilized to simulate stress distributions in a mine section which occur in response to a longwall mining operation. Due to the availability of the Cray supercomputer, a large-scale three-dimensional finite element model was developed for the analysis. The Hoek-Brown failure criterion, which describes a realistic behavior of rock masses, was used for the simulation of progressive failure. A comparison of calculated and monitored stresses in the mine has shown that the model gives a good representation of stresses in the mine structure.

Jan 1, 1990

By V. Rajaram

The Parachute Creek Member of the Green River Formation in the Piceance Basin, Colorado, contains vast reserves of oil shale, nahcolite, dawsonite, and other accessory minerals. The dry alkali process of sulfur dioxide removal using nahcolite (naturally occurring sodium bicarbonate) has great potential. A room and pillar mining scheme has been designed to extract a nahcolite zone occurring at a depth of 472 m, from the lease application area of the Yankee Gulch Joint Venture. Geotechnical parameters affecting mine design will be discussed. A preliminary development plan for mining at the rate of 1000 t/d will be described in detail.

Jan 1, 1977

By R. K. Singhal

This new tool can be used for the proper assessment of the potential economic wealth of any risky capital project. It does provide an unambiguous recommendation of the type "go or no go" to the decision-maker simply by comparing two different ratios profit/investment. One ratio determines the minimum value required to at least break-even while the other measures a probable value based on the asymptotic theory of statistical extremes (weakest link concept). Its application is briefly illustrated by means of an underground gold mine project, an oil sands mine project and a poly-metallic open pit project.

Jan 1, 1993

The initiation of a panel cave is an extremely important and infrequent event in the life of a large underground caving operation. A new cave was initiated at the Henderson Mine in 1991, 15 years after its first cave had been developed in 1976. The original cave was started after a half billion dollars had been invested in the development of the mine, mill and 23 km haulage system. Many things had changed since 1976, the most significant of these being much lower realizations for molybdenum. In 1976 the high demand for molybdenum and uncertainty of caving characteristics, formed the basis for a very conservative cave initiation sequence with miles of boundary weakening and inspection drifting. In 1991 the highly competitive molybdenum market in conjunction with 15 years of caving experience made for a very different mining climate.

Jan 1, 1994

By R. Perez

The consumption of grinding media forms a significant part of the operating cost of a mineral processing plant. An estimated half billion pounds of steel in the USA and over one billion pounds in the world are consumed each year in wet grinding alone. However, there is some conjecture as to the interacting roles of abrasion and corrosion. In order to provide a more complete picture of the conjoint action of abrasion and corrosion, marked ball tests were conducted on different grinding ball compositions in a laboratory ball mill and the metal losses were measured on varying the conditions, i.e., pH, PO2, in wet grinding a Cu-Ni gabbroic rock and compared with taconite grinding. Ball wear rates ere discussed with respect to ball composition and microstructure and the varying conditions used in the grinding tests.

Jan 1, 1984

By A. W. Khair

This paper presents an analysis of the dynamics of bit wear on the productivity of the continuous miners. Two field surveys have been carried out. The first survey was to assess the impact of bit wear on productivity and production cost. The second survey was to study the wear characteristics of the cutting tool (i.e. magnitude, forms, and mechanisms of bit wear). Primary factors affecting bit wear is identified and laboratory experiments were carried out to study the effects of some of these primary factors on wear in detail. Results indicate that bit wear has a significant effect on the productivity of the continuous miners. Furthermore under the severe geologic conditions (i.e. cutting rock partings and roof and floor rocks) bit wear not only hampers the productivity, but also increases the production cost due to a higher number of bit consumption. This study also indicated that bit wear accelerates beyond 20% of the conical height loss which corresponds to 7% of the weight loss. This increase rate of wear is an indicative of higher abrasion between bit body and cutting material, resulting in a dustier environment.

Jan 1, 1993

By Jerome E. Grader

Special-purpose analog computers are being profitably applied in the process industries to perform miscellaneoas online computing functions in situations where conventional measurement and/or control hardware cannot perform a required task satisfactorily. This paper will discuss the application of such equipment in the mining industry. It is divided into two parts, beginning with a description of operation of the hardware, followed by a discussion of several applications of the computers to mining industry control problems.

Jan 1, 1969

By Burke Trafton

An earlier paper1 introduced a rapid solution for mine ventilation network problems, employing the digital computer. In this paper, refinements and additions to the computer program which expand its scope of application and a solution to a ventilation network having a coal-mine configuration are presented. Specifically, the revised program--written in FORTRAN for the IBM 7074 computer in Penn State's Computation Center--is applicable to any mine ventilation network employing natural splitting and having its fan located externally. It accomplishes the following; 1. Distributes an assumed total quantity of air flow among all air- ways of the network, performing iterations until an acceptable level of error is attained and the flow in each airway is known. 2, Computes the pressure drop (head loss) in all airways and the overall network and mine head losses. 3. Determines the operating point for the mine and a given fan, adjusting all air flows and head losses to the actual values.

Jan 1, 1964

By K. S. Whiting

Elevated concentrations of copper, cobalt, and arsenic within the Panther Creek Basin sediments in north central Idaho prompted an evaluation of the sources of the metals. Potential tailings and waste rock source samples collected at the head of Blackbird Creek were compared to sediment samples in the Panther Creek Basin using electron microprobe techniques. The mineral types, degree of alteration, and the morphology of the metal-bearing sediment grains within Blackbird and Panther Creeks were found to consist of copper-, cobalt-, and arsenic-bearing sulfide minerals.

Jan 1, 1997

By J. P. Hanten, G. Ramadorai

This paper presents laboratory and pilot plant data on the removal of heavy metals and molybdenum from mining-milling waste water. Molybdenum is removed as an Fe-Mo precipitate by proper addition of ferric sulfate. Heavy metals are lowered by lime treatment. Solid-liquid separation was achieved in both cases by flotation techniques. The Lectroclear electrocoagulation-electroflotation process was used to achieve the desired degree of metals removal. Good correlation was obtained on the laboratory and pilot plant scales. A two-step process consisting of the sequential removal of molybdenum and heavy metals was tested successfully using a mobile pilot plant. Preliminary data on sludge characteristics was obtained and the feasibility of recycling the iron sludge for iron and molybdenum recovery was established on the laboratory scale.

Jan 1, 1987

By L. Bloom

In 1996, lack of confidence in assaying methods and sample handling affected companies as diverse as Bre-X and Timbuktu. Both share prices and the ability to raise financing are impacted when the quality of assay data is suspect. Overseas projects are subject to enhanced scrutiny when local facilities are used that are unfamiliar to brokers, financing agencies and banks. Quality control systems can be -implemented but there are associated costs. These costs should reflect the risk to the mining company, investors and financiers and the size of the proposed investment. In this regard, assay control call is considered a form of insurance to enhance the value of an exploration or mining project.

Jan 1, 1997