Search Documents

If the communication/tracking system of an underground mine is severely damaged in a large mine accident or explosion, a surface based seismic system could be the only available tool for locating any trapped miners. This paper documents a field test of a seismic system at a room-and-pillar coal mine in Eastern Kentucky. Testing was performed at 6 different depths (450, 575, 750, 1175, 1525 and 1700 ft) above the mine. For each location underground, the miners pounded a ?set? of 5 ?repetitions? on the roof with each repetition being about one second apart. Over the 3 day field test, 63 sets of underground miners? pounding were detected by the seismic system at depths up to 1175 ft and at horizontal offsets up to 890 ft. Also during the testing, the observed signal strength generated by pounding with a crib blocks was seen to average 180% stronger than the observed signal strength generated by pounding with a sledgehammer. Ultimately, this field test was very successful and definitively demonstrated the ability of the seismic system to detect potential trapped miners? pounding up to a depth of 1175 ft.

Feb 23, 2014

By J. S. Lee

Alkyl hydroxamates are well known collectors for oxide copper minerals as evidenced by the large amount of published literature. Our studies on a wide variety of copper ores from around the world have shown that alkyl hydroxamates will recover most of the "floatable" oxide copper minerals from an ore. They are available commercially, and they offer many advantages over alternative technologies for oxide copper recovery. In spite of this, the full potential of hydroxamates has not been exploited in the industry. The objective of this paper is to provide relevant practical aspects and guidelines to facilitate successful application of hydroxamates in operating plants. A critical analysis of the available information and data, based on several case studies, notation testing, and microscopic analysis indicates that alkyl hydroxamates can effectively recover well-defined oxide minerals of copper, but not copper occurrences such as Cu-bearing goethite (often misidentified as cuprite) which report as Acid Soluble copper in chemical assays. Prior to any notation testing with hydroxamates, it is necessary to assess the various modes of occurrence of Acid Soluble copper using microscopic and microprobe analysis.

Jan 1, 1998

By A. Khan

The effect of sulfur dioxide on collectorless and collector induced flotation of chalcopyrite was studied by cyclic voltammetry on a rotating disc electrode. Contact angle measurements were made to determine the effect of sulfur dioxide concentration and electrochemical treatment. The benefits of sulfur dioxide in enhancing the selectivity of separating chalcopyrite from complex sulfide ores are discussed.

Jan 1, 1996

By S. C. Suboleski

In a high risk venture such as mining where capital is committed and contracts are signed on the minimum of information, decisions are based primarily on production forecasts derived through consideration of such factors as management-labor relations, mining practice, variations in physical conditions and the equipment applied. Among these factors, the physical conditions offer the least opportunity for control and, due to the wide range of mining conditions that may be experienced, little effort has been made to develop objective methods for measuring their effects on mine out- put. The aim of this paper is to demonstrate a method for assessing these relationships that can be applied under a wide range of conditions both in new mines and in working sections where there is a need to determine the impact of proposed operational modifications. psing empirical data from active underground mines, a mathematical model was developed to derive a set of regression equations for predicting production as a function of mining conditions

Jan 1, 1980

By Lyle A. Hale

The subject area known as upper Dry Valley is located 15 miles due east of Soda Springs in Sections 14 and 23, Township 9 South, Range 44 East, Caribou County, Idaho. The railroad extending from Soda Springs to its terminus at El Paso's Maybe Canyon mine is 8z miles to the north in lower Dry Valley. Initial data derived from trench work in 1962 revealed a variety of econom¬ically significant alterations of the phosphatic beds related to the rather unique geomorphic development in the northern part of phosphate lease 1-012989. It was apparent that such conditions, while valid for near-surface beds in a strike direction, would be misleading if projected to the proposed depth limits of strip mining. Consequently, a subsurface mapping program was initiated in 1963 to determine: (1) the depth and horizontal extent of weathering and related phe¬nomena, (2) the depth, thickness, and quality of ore beds and intervening strata, and (3) structural geology as a guide for mining procedures. Successful use of a scintillometer in 1956 to detect the subcrop position of phosphate beds in the Smokey Canyon area of southeastern Idaho led to the conclusion that gamma radiation surveys of drill holes could be a useful aid in subsurface mapping. The objectives of this paper are: (1) briefly to describe geologic features characteristic of the phosphate lease area and (2) to demonstrate the practical application and theory behind gamma radiation logging as an effective tool in the economic evaluation of a phosphate lease.

Jan 1, 1969

By B. S. Crocker

Introduction Pebble mill grinding can be defined as wet or dry grinding in a tumbling mill with pebbles used as grinding media instead of metal balls. To clarify the terminology, which may differ in the various mineral industries, it is essential to point out the differences between grinding with partially sized and carefully sized grinding media. When grinding with partially sized media (limited top size only), sizing is usually the setting of the primary crusher and there is no bottom sizing-all fines, chips, sand, and small sizes are included. This is often called run-of-mine or primary autogenous grinding. In this case the entire crusher discharge is fed into the mill and part of it becomes "charge" and the rest is "sand feed." When grinding with carefully sized media (i.e., media that is sized both at the top and bottom of the size range), no fines or chips should be present in the charge to the mill. This is pebble milling and the grinding media consists of ore, rock, Danish pebbles, gravel pebbles, or ceramic pebbles-media that is appreciably lighter than steel balls. The grind¬ing charge is fed to the mill to maintain a load and it does the grinding usually on a classified sand product of suitable size. If the grinding media is the same as the raw material being ground, this type of grinding is also called secondary autogenous grinding. Pebble milling was in common use in the gold mines of South Africa in the early 1900s. It is by far the oldest form of autogenous grinding. It may be used to grind crushed ores from a maximum size of about -% in. to all -10 µm. Pebble milling differs from "run of mine" grinding in many ways, but two big differences are: I) The ore itself is crushed to approximately t/4 in., or it may be further reduced to 8 or 10 mesh in a rod mill or fine crusher. 2) Then carefully screened ore of the correct size is placed in one or more stages of pebble mills to grind the ore to its desired final size. The media size is carefully selected to be the most efficient for the particular size reduction required in each stage. This is a precise practice, and pebble mills can be designed as easily and accu¬rately as can rod mills or ball mills by those skilled in the art. A pebble mill is a rotating cylinder in which the grinding media has been carefully sized for the job in hand. If the mill is doing coarse grinding, the media will be correspondingly large and the mill might be called a primary (or intermediate) pebble mill or a lump mill. If it is to do fine grinding, the media selected is proportionately smaller and the mill would be called a secondary or tertiary pebble mill. The media itself is normally rounded pebbles made from screened ore from the primary-crusher discharge. The charge could be rounded pebbles of the correct size removed from a primary autogenous mill, or the pebbles could be carefully sized gravel, sized beach pebbles, or sized flint pebbles. Usually the specific gravity of a pebble is from 35 to 55% of that of steel balls. It commonly varies from 2.66 to 4.2, depending on the specific gravity of the ore. Primary pebble mills, or lump mills, would be charged with pieces of rock up to 10 in. maximum and 5 in. minimum and would grind crusher discharge with a maximum size of 1/4 in. on hard ores and 3/8 in. on softer ores. Secondary pebble mills could be charged with pieces of rock screened on 4 x 4-in. square mesh and retained on 1 1/2 x 1 1/2 in. These mills would grind material with a top size of 8 to 10 mesh. Tertiary pebble mills could be charged with screened rock that would pass 3 x 3 in. and be retained on 1 x 1 in. and grind 35 to 48 mesh sands. Principles of Operation Media Size To operate a pebble mill efficiently it is imperative that great care be taken in screening the rock feed that is fed into the mill to round up into a range of pebble sizes that are suitable for grinding of the sands that are also being fed into the mill, having regard to the top size and the average size of such sands. Since most mill operators know from experience the correct size of steel balls to be used in a mill to handle different sizes of sand feed, it is convenient to relate the pebble size to a ball size. If the correct ball size is not known, it is relatively simple to conduct batch laboratory tests in 12- to 18-in. laboratory mills to determine the optimum size of steel ball. Also, Bond and others have published formulas for calculating the optimum ball size. When the correct size of the individual steel ball is known, then a pebble of the same weight will perform the same grinding if used in the proper size of mill and under the proper conditions, which will be defined later. This media size, as defined by the average weight of the individual pieces, is most important. The following tests will serve to clarify this point. Laboratory Tests Using Steel Balls or Pebbles. Several labora¬tory grinds were made to compare a given size and weight of steel ball with a pebble of the same weight but larger size, and of the same size but lighter weight. The following loads were used in the 12-in. laboratory mill: All 1 1/4-in. steel balls weighing 122 ± 10 g. All 1 3/4-in. pebbles weighing 123 ± 5 g. All 1 1/4-in. pebbles weighing 45 ± 3 g. To equalize capacity, the test with the steel balls was run only 34% as long as the tests with pebbles. In each case, 2,500 g of primary sands were ground at the optimum gravity for the media being tested at a speed 78 1/2 % of critical speed, and for 170, 340, and 680 revolu¬tions for the steel balls, and 500, 1,000, and 2,000 revolutions for the pebbles. The first test is summarized in Table 74 by showing the 80% passing size in microns for the feed and for each of the grinds. Two other tests are summarized in Table 75 showing the screen analyses

Jan 1, 1985

By Paul W. Johnson

Chemical mining is the in situ extraction of metals from ores located within the confines of a mine (broken or fractured ore, stope fill, caved material, ores in permeable zones) or in dumps, prepared ore heaps, slag heaps, and tailing ponds on the surface. These materials represent an enormous, untapped, potential source of all types of metals. The field of chemical mining, now in its infancy, encompasses the preparation of ore for subsequent in-place leaching, the flow of solutions and ionic species through rock masses and within rock pores, the leaching of minerals with inexpensive and regenerable lixiviants under prevailing conditions of the in-place environment, the generation and regeneration of such solutions, and the recovery of metals or metal compounds from the metal-bearing liquors. It is not inconceivable that eventually our ore reserves will consist largely of low-grade, refractory, and inaccessible new deposits and low-grade zones near previously worked deposits, caved and gob-filled stopes, waste dumps, tailing ponds, and slag-heaps. Chemical mining promises economic recovery from these types of deposits. Before it can come of age, however, a much better understanding is needed concerning its chemical and physical aspects.

Jan 1, 1967

In order to overcome some of the deficiencies associated with conventional fine coal cleaning methods, a novel process known as microbubble column flotation (MICROCEL?) was developed at Virginia Tech. This article provides an overview of recent commercialization efforts and in-plant testing of this technology. The results of the in-plant test work indicate that the MICROCEL technology offers several advantages for the upgrading of difficult to clean coals. The test data have also been used to develop guidelines for the design of coal flotation columns and to validate existing scale-up procedures.

Jan 1, 1991

By Jose M. S. Ramos

This paper describes the slope stabilization procedure at Cauê Mine, Companhia Vale do Rio Doce - CVRD, Itabira, State of Minas Gerais, Brazil. Cauê Mine, is a large open pit, to produce about 41 million tons of iron ore during 1974, and an intensive program of investiga Lion was carried out to provide the basic data for stabilizing its slopes, The ultimate rock slope in the W area will be about 400 m high with dipping angles decreasing gradually from top to bottom of the pit. The investigations started in 1969 and since then many geologists and engineers, from both CVRD and Geotécnica S/A., assisted by international consultants, have given their contribution to the achievement of solutions. It is hoped that this paper may contribute to the slope stability of other mines in tropical climate.

Jan 1, 1974

By D. A. Peterson

A research program is currently in progress at the University of British Columbia to determine the potential of composite cable bolt reinforcement in Canadian mines. Several prototypes of glass fibre cable bolts have been tested. Their evaluation consisted of lab testing at the University of British Columbia, United States Bureau of Mines (Spokane) and trial installations at Detour Lake, Winston Lake, and Myra Falls Mines. A market analysis of cable bolts within the Canadian mining industry has been completed. Fibre reinforced polymer composites have a high potential as cable bolt reinforcement in mining applications. They prove to be a viable alternative to steel cable bolting.

Jan 1, 1993

By Ilmar J. Martens

The statistical information and cost data used in this report has been made available by NICKDATA INC. Since 1982, NICKDATA INC. of Toronto, Canada, has produced an annual comprehensive nickel industry cost study. Up to date information on 22 mines, 21 smelters, and 16 nickel refineries representing 30 nickel production operations in 17 countries are included in the computerized cost analysis. The report is compiled from information obtained through regular annual visits to major nickel operations and continuous monitoring of information on all nickel producers. The 1984 report which was completed this summer, reveals drastic changes in the nickel industry cost structures.

Jan 1, 1984

By P. Tsang

To gain insight into the current status of pillar design practice in the underground coal mines of United States, a survey has been undertaken in the late 1993 and early 1994. A total of 552 room-and-pillar mines and 75 longwall mines have been surveyed to collect general, geological and mine plan information. The collected information are critically analyzed with special emphasis on the pillar design criteria adopted in these mines. A safety factor analysis has also been carried out for the pillars in room-and -pillar mines.

Jan 1, 1995

By K. A. Wheeler

To evaluate the effects on groundwater of a proposed in-pit disposal operation at an east Texas lignite mine, the local geologic, hydrogeologic, and geochemical features were thoroughly characterized. Resultant data were used in a flow and transport model (SWIFT) to simulate migration of the ash leachate. Computer simulations indicate that the leachate plume will travel 61-152 meters from the disposal area in 100 years after resaturation of the spoils. A 61-meter buffer zone of mine spoils without ash will surround the disposal area. The proposed landfill operation received regulatory approval and is currently operating as a Class 2 non-hazardous landfill.

Jan 1, 1994

By D. Bhattacharyya

The adsorption and desorption of gold cyanide by activated carbon is significantly influenced by particle size of the activated carbon particles and the chemical environment. A series of adsorption and elution experiments have been performed with ten different particle size fractions. The tests indicate that although the ultimate adsorption capacity is independent of the activated carbon particle size, the adsorption rate is strongly affected by the particle size. Further, desorption characteristics using traditional Mintek and atmospheric Zadra procedures reveal interesting trends with variation in particle size and will be discussed in this paper.

Feb 23, 2014

By Roy A. Grancher

Construction materials indeed face a dilemma...as does the building industry as a whole. A stop & go economy; a severe drop; in housing starts; lingering indecision over just what corrective steps are to be taken or to their degree of commitment; no less basic disagreement in regard to which of the, Nation's problems is really the most pressing -- inflation or recession? Optimism has become a rare quality these days. At moat the cautious view is that this new year will see a long, hard struggle back, with hopes that 1976 at least can truly mark a dual anniversary celebration for the United States and its economic health. Yet the paradox is that once recovery does return, those very construction minerals and materials --which in recent years have experienced the ups and downs of overcapacity, shortage, and now declining demand again-- will once more face the spectre of mass inability to service revived and growing needs for its product. Mounting costs, present marginal expansion investment, and substantial lead times required for new facilities to come into production, could well form a bottleneck to economic upswing. The result again can be another cycle of shortage-induced inflation, and with it continued gyrations within the demand supply relationships of the country's building industries.

Jan 1, 1975

By John J. Stetler

The Companhia Vale do Rio Doce in Brazil operates one of the most extensive systems in the world for the mining, transportation, processing, pelletizing and shipping of high grade hematite iron ore and pellets. Current shipping of unbeneficiated, sized, high grade ore from its ports at Tubarão and Vitória is now at the rate of 17,500,000 metric tons annually. An increase in this annual rate is now under study. Using the technology and facilities of Lurgi (1) and Arthur G. McKee company CVRD undertook a program to process and pelletize two types of fines - "Blue Dust" and ?Itabira Fines?. Blue Dust is a high grade fine ore which was bypassed while mining the direct shipping ores and which, also, exists as a very large ore body called the Conceição Mine. Itabira Fines is a lower grade of fine ore which is comprised of in-situ fines and, also fines which are generated in sizing the direct shipping ores for a rigid specification market.

Jan 1, 1970

By William J. Stone

Large reserves of coal and uranium exist in the San Juan Basin of northwestern New Mexico. The mining and development of these resources necessarily also involves depletion of area water resources and disturbance of the hydrogeologic framework. In an effort to better define the water resources and hydrogeologic framework of this region, the New Mexico Bureau of Mines and Mineral Resources, the U. S. Geological Survey, and the State Engineer's Office are presently engaged in a cooperative study of the Hydrogeology and Ground-Water Resources of Northwestern New Mexico. The purposes of this paper are to introduce our project, review tine coal and uranium resources of the San Juan Basin, and discuss the various hydrogeologic considerations recognized in their exploitation.

Jan 1, 1976

By A. D. Hammond

Vanadium is a transition metal, ductile, silver-gray metal. It is harder than most metals and steels and it has a good resistance to corrosion, it is stable against alkalis, sulfuric and hydrochloric acids. Vanadium is oxidized in air about 660 °C, although an oxide layer forms even at room temperature. The chemistry of vanadium is noteworthy for the accessibility of the four adjacent oxidation states 2-5. In aqueous solution the colors are lilac V2+, green V3+, blue VO2+ and, at high pH, yellow VO42-. Considered to be as abundant as zinc, metallic vanadium is not found in nature, but it is known to exist in about 65 different minerals. Economically significant examples include patronite (VS4), vanadinite (Pb5(VO4)3Cl), associated to the uranium mineral carnotite (K2(UO2)2(VO4)2?3H2O) and in a vanadium mica called, roscoelite K(V3+,Al,Mg)[(Si,Al)4O10](OH)2. Other important vanadium ore oxides are montroseite (V,Fe)O(OH) and corvusite (Na,Ca,K)V8O2.4H2O. Much of the world's vanadium mine production comes from magnetite-hosted deposit and to a lesser extent, in sedimentary-hosted sandstone. Vanadium is also present in bauxite and in fossil fuel deposits such as crude oil, coal, oil shale and tar sands. In crude oil, concentrations up to 1,200 ppm have been reported. A significant vanadium production comes from the processing of petroleum residues, fly ash and recycling spent catalysts. In 2011, metallurgical applications accounted for 93% of the use of vanadium. Here, an alloy called ferrovanadium is utilized to strengthen steel to be used as rebar in the construction industry, in the manufacturing of axles, crankshafts, gears and chassis in the automotive and transportation industries and in the manufacturing of high-speed tools. In the aerospace industry, vanadium is utilized as a titanium alloy in the manufacturing of airframes and jet engines. The reason for the wide use of vanadium as alloy is its high strength-to-weight ratio, the highest of any engineered material on earth. The major non-metallurgical use of vanadium is in the production of catalysts for the chemical industry. The most commercially important compound is vanadium pentoxide (V2O5), which is used as catalyst in the production of sulfuric acid.

Feb 23, 2014

By Nikhil Dhawan, Shrey Agrawal

India’s most extensive renewable energy expansion program targets 280 GW of solar energy by 2030. Due to the massive generation of photovoltaic waste (expected 34,600 T by 2030), stringent recycling effort to recover metal resources from endof- life PVs is required for resource recovery, circular economy, and subsequent reduction in the environmental impact. The present study investigates the recycling potential of end-of-life silicon solar modules. The feed characterization reveals that most of the values in PV modules are concentrated in the frame (pure Al), Si wafer (72–84% Si, 9–12% Al, and 0.13–0.71% Ag), and electrical connections (Cu wire coated with Sn). The Si and Ag values in the feed were beneficiated using water fluidization, and concentrate with 90% Si and 2% Ag was attained in the underflow concentrate. Ag values were recovered in the form of AgCl by leaching in nitric acid and precipitation. After the purification step, the residue containing 99% Si can be further utilized to fabricate Si wafer and Al-Si alloy. The preliminary cost estimations suggest that the proposed process is economically viable for the recycling of solar panels with the maximum value generated from the AgCl precipitate followed by Al panels and Si wafers.

Nov 14, 2022

By P. R. Taylor

A reaction is evaluated by which heated and pressurized water is used to precipitate metal oxides from loaded Kelex 100 complexes. Pure copper oxide (CuO) and pure nickel (Nio) in powder form, and ranging in average size from 12 to 25 micrometers, were found to precipitate from copper and nickel loaded Kelex 100/kerosene complexes, by water heated and pressurized to between 374 and 400 °c and 2170 psig (148 atm) and 3500 psig (238 atm). The precipitation is suggested to result from hydrolysis of the metal, following exchange for the hydrogen in the phenolic hydroxyl of the Kelex 100 structure, enhanced by the conditions provided by heated and pressurized water. The reaction is believed to have the characteristics of homogeneous nucleation and heterogeneous growth. The effects of temperature, pressure, initial metal concentration and seed addition on the kinetics of the process were studied. In addition, characterization studies were performed on the reaction products. A detailed discussion of the experimental results is presented.

Jan 1, 1992