Search Documents

By T. McDonald

Test work indicated and plant operation has since confirmed that SAG milling is a viable option for INCO's Sudbury Operation milling rationalization project only if pebble crushing is included in the SAG/ball mill circuit. Throughput increases more than fifty percent with pebble crushing incorporated into the comminution process. The finer product of high speed pebble crushing provides further energy savings. The unconventional approach of pumping the pebble crusher product, while simplifying plant layout, has produced challenging wear problems.

Jan 1, 1992

By G. Bonifazi

In the present work the possibility to utilize the morphometrical and morphological characteristics of an articulate solids system in a slurry flow to monitorate and to control a continuous process is considered. This goal has been reached by mean of an optical system able to acquire, to handle and to process the pictorial information derived by a suitable hardware architecture designed to realize the best lighting, focusing and sampling conditions for the examined flow stream domain. The procedure has been tested using different flow stream slurries coming from different sections of a beneficiation plant. A suitable strategy and a consequent software architecture has been set up in order to assure to the system the necessary speed and the stability to achieve correct on-line measurements and control.

Jan 1, 1994

The viability of physico-chemical purification methods such as selective flocculation for separation of two components having similar chemical composition and same crystal structure but different surface properties is demonstrated. Loss of selectivity was observed in a dolomite-dolomite mixture with Polyethylene Oxide (5 million molecular weight) as the flocculant. Hetero-flocculation was minimized using a low molecular weight PEO (MW -105) as the site blocking agent (SBA). Near complete separation was achieved at pH 10.5 at 100% recovery level.

Jan 1, 1993

Little knowledge is available that considers the effects of continuous miner position on the possible respirable dust exposure of the remote mining machine operator. Such information could be very useful for increasing the awareness of the remote operator as to those parts of an extended cut that generate higher levels of respirable dust. This data could be used to develop guidelines for positioning the remote operator to reduce his potential exposure. This work details the effects of continuous miner position on dust levels measured on the machine and at the remote continuous miner operator location.

Jan 1, 1998

By R. B. Elver

The level of steel consumption per capita is one of the principal indicators of a country's standard of living. It is no coincidence that the materially advanced nations possess viable iron and steel industries to provide a reliable and economic source of steal for the manufacturing industries. No other metal is as dominantly important in manufacturing as steel. The blast furnace - steel furnace complex based on coking coal, ferrous scrap and iron ore - continues to be the principal steel-producing method. Less important is the electric furnace method based on scrap, In recent years, there has been considerable interest in the many direct reduction processes that are not dependent on coking coal but usually produce a product for further refining in steel furnaces. No matter which series of processes are used, iron ore is essentially the only source of virgin iron units. Thus, to such a vital and capital-intense industry as steel, access to a relatively inexpensive, long- term supply of iron ore is essential.

Jan 1, 1964

By F. H. Nehl

The U.S. Bureau of Mines investigated the selective electrowinning of Ag and Au from cyanide solutions contaminated with Cu with the goal of decreasing the amount of Cu co-deposited. Decreasing Cu co-deposited will reduce refinery costs. Direct current was applied to the cell in pulsed and square wave voltages at 0.7 A?h per 150 mL of solution. Times tested for each cycle ranged from 1 to 10,000 ms. Graphite, lead, and stainless steel were evaluated as electrode materials. Square wave e1ectrowinning at 70? C gave the best separation of Ag and Au from Cu. Applying 2.5 V during the duty cycle, 0.0 V the rest of the period, a duty cycle of 10 to 30 pct, and a period of 100 ms to 1,000 ms gave the following results: Ag concentrations decreased from 34 µ g/mL to 0.1 µ g/mL, Au concentrations decreased from 54 µ g/mL to 0.2 µ g/mL, and Cu concentrations remained almost constant at 560 µ g/mL.

Jan 1, 1993

By K. J. Shoop

This study investigates the use of a horizontally-baffled column (7.6 cm inside diameter by 344.2 cm high) to reduce the ash content of a high ash bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feed rate, reagent dosage, and feed quality, and to compare its performance with a conventional column installation in an operating plant. In this paper, the results of this investigation will be reviewed and discussed.

Jan 1, 1997

By H. Maleki

Interwest Mining Company has been collecting geologic data within the last decade in preparation for underground mining of extensive coal reserves in its Bridger Coal property in southwestern Wyoming. During a preliminary data collection program in 2000, Interwest Mining completed geologic investigations, including surface mapping, drilling, aerial photography, rock testing, and limited groundwater investigations. Core from 12 exploration boreholes in the area of interest was tested to determine the mechanical properties of the coal seam and the immediate roof and floor for evaluation of the feasibility of underground mining. Geologic investigations identified the presence of one 7-to-17-ft-thick coal seam throughout the reserve under 1400 ft of cover. During a geotechnical feasibility study in 2002, the authors reviewed available data while completing comparative analyses identifying critical deficiencies in these data. The study projected moderate-to-difficult mining conditions, considering the weak nature of near-seam strata and depth of cover, and thus recommended limiting the longwall reserves to an overburden depth of less than 900 ft. These shallow remaining reserves were located at depths within regional mining experience to justify longwall mining methods. Based on a critical examination of available data, Bridger proceeded with more detailed data collection to improve understanding of the depositional and structural setting of the reserve, hydrogeologic conditions, overburden strength, and premining stress conditions. Additional data was collected during 2003 and 2004 field programs. Since 2003, Bridger has had the opportunity to observe ground behavior in a series of up to 1200-1600-ft- long rectangular openings created during highwall mining. These narrow unsupported openings remained stable in the short term in large areas but the overburden subsided locally in the long-term depending on geologic and panel layout designs. These localized subsidence events allowed an examination of in-situ coal strength based on back analyses of stress. The unextracted highwall areas near Ramp 17 provided an ideal location to access the underground reserves using a 6-entry set of mains. The existing north-south oriented longwall layout for the Bridger Coal was selected by Bridger to maximize resource recovery from the D41 reserves while considering operational and geotechnical constraints. At 45-degrees deviation from preexisting joints and mild horizontal stress field, this orientation was considered beneficial for overall stability while using both sets of joints for facilitating the caving process. The present layout utilizes pillars on 80- to 90- by 200-ft centers, 17-ft entry spans and 750-ft wide longwall panels (Figure 1). Gate pillars are on wide spacings and are intended to act as abutment-abutment pillars to limit strata deformation over the gateroads during longwall mining.

Jan 1, 2008

By M. S. Klima

A 25-mm diameter dense-medium cyclone was tested to investigate the effects of geometry and operating conditions on cyclone performance when processing -150 I'm coal. The emphasis was on examining those variables (e.g., flow rate and inlet velocity) which impact the separation kinetics (specifically the number of g's and the mean retention time) and the occurrence of apparent bypass. Apparent bypass, indicated by partition curve "tails", results from the short circuiting of the feed coal to one or both of the product streams and represents a loss and/or contamination of the clean coal. This paper presents the results for this series of tests.

Jan 1, 1993

By D. E. Healy

In 1989 an Autogenous Grinding Task Force was formed to study potential autogenous grinding circuits to replace the existing semi-autogenous grinding at the National Steel Pellet Plant located in Keewatin, Minnesota. Pilot plant test work performed by the Hanna Research Center (HRC) indicated that fully autogenous grinding with pebble extraction and crushing could feasibly be incorporated into the existing circuits. In 1990, one of the existing ten grinding mills was converted for an in-plant test incorporating pebble crushing. The full scale test work conducted in 1990 and 1991 verified the pilot plant projections with primary mill throughputs from the fully autogenous circuit utilizing pebble crushing being greater than throughput of the existing SAG mill circuits.

Jan 1, 1992

By George C. Hawley

Historically, mica usage has been low because of limited availability; as a by-product of many small processors, who have lacked motivation for extensive R & D. The discovery of a 30 million ton deposit of 85-90% pure phlogopite, when existing markets are only 300,000 tonnes annually, forced the search for large volume new markets. Increasing costs of energy, petrochemicals, plastics and glass fibers, and environmental constraints on asbestos usage, have led to new opportunities for mica as a reinforcing filler. Extensive research and developments; in beneficiating, processing and treating mica, has been necessary to satisfy these new markets.

Jan 1, 1981

By S. S. Peng

High horizontal stress has been well recognized as a significant factor in roof control. It can adversely affect roof stability if the panel is designed improperly. Mining experience has shown that it can cause a cutter roof. The effects of high horizontal stress on roof stability depend on many factors such as magnitude and direction of the maximum principal horizontal stress, ratio of the maximum to minimum principal horizontal stress, structure and mechanical properties of the immediate roof and mining sequence. However, little is known about the intrinsic mechanism of high horizontal stress effect on roof stability except some conceptual explanations. In order to design a stable entry, the redistribution and concentration of high horizontal stress around the openings must be fully understood. Using the 3-D finite element analysis technique, this paper presents the redistribution and concentration of high horizontal stress field for a three-entry system with different orientations of horizontal stress. Based on the horizontal stress redistribution, possible roof failure for different orientations of horizontal stress is analyzed.

Jan 1, 1996

By A. K. Bhowmick

Size reduction is very energy intensive and is the single most power-intensive operation in mineral processing plants. Research has shown that only a small part of the energy is utilized efficiently. One of the major thrusts of all equipment manufacturers has been to improve this efficiency. Choosing the right equipment to maximize energy utilization in any comminution application has always been the utmost criteria. Due to the high energy cost and depletion of good grade minerals, it is becoming essential to optimize all the subsystems within a given comminution system for the overall economic success of such ventures. Bradley Pulverizer Company of Allentown, Pennsylvania recognized this and started offering its Feeder Controller in 1988 for automatic feed control. After its first successful operation, Bradley made this as a part of all of their grinding system standard offering. It was also recognized that the Feeder Controller was just a beginning and more automation and controls would be required for an overall, efficient grinding system.

Jan 1, 1993

By Fernando Muge

A complex pyrite orebody located in the South of Portugal (MO INHO) was exploited in the past by cut and fill methods until a certain level. It was decided to design a new plant for non ferrous metal extraction and the rate of production and exploitation method was modified accordingly. So, a sub level stoping (SLS) method was en visaged for the exploitation of the deepest part of the orebody (under 265 m level). For the planning of this SLS method, it was decided to perform a geostatistical study of the orebody, on the basis of the available information, which consists mainly of channel samples assayed for Cu, S, Zn and Pb.

Jan 1, 1979

By Stephen Stone, Kerby Dobbs, G. Richard Whittecar, W. Lee Daniels, Zach Agioutantis, Tess Thompson

A common result of Environmental Impact Assessments associated with mining projects is the construction of new wetlands in areas disturbed by mining operations. Where appropriate, this mitigation may be considered an integral part of the mine reclamation process under the principles of sustainable development in the minerals industry. Wetbud is a new tool for estimating wetland water budgets using available weather data and site-specific topographic, soil and geohydrologic data, coupled with mass balance mathematics. Wetbud is primarily intended as a planning tool for use in the design of created wetlands, but it can also be applied to native wetlands or wetland restoration sites where the required input parameters can be specified. Wetbud can be run in its basic form where wetland topography, soil parameters and groundwater flux are simplified, or in the advanced form, where these parameters are included in a more complex approach via integration of the MODFLOW package, a free 3D program that was developed by the United States Geological Survey. Both versions can also include overbank flow hydrology sources and the advanced form can also model sloping and irregular topography. The program downloads weather data from the nearest applicable station and selects appropriate wet-normal-dry (W-N-D) years following a modest user data clean-up step. Wetbud also has the ability to utilize existing short-term (e.g. 6 to 9 months) groundwater data from an up-gradient well to simulate longer-term groundwater level inputs for the selected W-N-D years. In addition, Wetbud features a “Wizard” version that comes pre-loaded with 14 pre-selected weather data sets for all areas of Virginia that can develop a simple monthly water budget in less than 15 minutes – a feature that could be expanded anywhere geographically with historic weather data.

Jan 1, 2017

By Donald E. Zipperian

It has been recognized that froth flotation of mineral particles utilizing rising flow of micro size air bubbles, counter-current to quiescent falling flow of particles in a column type cell, provides a unique mechanical atmosphere conducive to extension of froth flotation process to much coarser and finer particles sizes than possible with mechanically agitated and aerated cells. 1,2,3,4. This paper describes metallurgical results obtained at several plant installations of large capacity commercial size Deister FLOTAIRE® Column Flotation Cells. These cells utilize air aspiration into surface tension lowered water to generate micro size bubbles. Operating costs, power, wear, and scaling characteristics of rougher, cleaner, and scavenger units are compared with mechanical units. Problems encountered and scale up criteria developed when increasing from 0.20m(8inch) diameter pilot cells to 2.42m(96inch) commercial cells are discussed.

Jan 1, 1985

A major Brazilian iron ore producer, SA Minerayao da Trindade (Samitri), has recently completed modifications at two operations which involve the use of Derrick high frequency vibrating screens. Details of these modifications are presented, together with a review of product quality improvements.

Jan 1, 1997

By B. S. Hulvey

Thin support liners are becoming more accepted and being developed with improved properties because the mining industry as a whole has been offering underground safe test trial sites. This is because of the huge potential for such products. Recent developments tend to indicate that the technology is “coming of age” and these are discussed in this paper.

Jan 1, 2003

By E. F. Draskovich

In 1984 a high temperature heat recuperation system was installed in the pellet plant of the National Steel Pellet Company located in Keewatin, Minnesota. The system is similar to those of Cleveland Cliffs Empire and U.S. Steel's Minntac operations. It recovers hot process air from the cooler by induced flow, and directs it to an intermediate zone between the drying and preheat zones on the grate machine. This system recently underwent further modifications in April 1985, following initial operation in 1984. The M. A. Hanna Company, which manages the property, developed the design criteria and made the subsequent recommendations for modification through its research facility in Nashwauk, Minnesota.

Jan 1, 1986

By Vijenac Quarry, A. Iljazagic, t. Knezicek, T. Omeragic

Limestone quarry Vijenac, is one of the key limestone producers in B&H. Conventional massive drilling and blasting is the technique applied for limestone exploitation. Utilized blasting scheme causes appearance of large oversize stone pieces, uncontrolled flying stone and undesirable seismic effects. In order to reduce or eliminate exposed disadvantages and to improve environment in the area of Vijenac quarry, an innovative blasting scheme was tested. Conventional blasting scheme was changed from single row, deep inclined blast holes combined with two lines short horizontal holes to multi row, inclined blast holes combined with a single line short horizontal blastholes. Applied innovative blasting scheme reduces negative blasting impact on the environment through safer working conditions, reduced amount of dust after blasting, reduced explosive and energy consumption, reduced appearance of explosive gasses and reduced earth and air vibrations as the result of seismic effects.

Jan 1, 2005