Search Documents

By Linda Frederick

In July 1997, Krupp Canada obtained the contract to design and supply the conveyor system for Chile's Los Pelambres copper mine expansion project. Progress on the overland conveyor system is currently on schedule. It is a challenging task to convey copper ore from an open-pit mine located on a mountain site 3,000 m (9,840 ft) above sea level down 1,300 m (4,265 ft) to the processing plant at the valley floor below. The Los Pelambres conveyor system moves copper ore at a rate of 8.7 ktlh (9,600 stph) and at a speed of 6 ml sec (1,180 ftlmin) for 12,750 m (41,830 ft). The distance is divided in three conveyors, each 1,800 mm (71 in.) wide. The largest conveyor is 6 km (3.7 miles) long. To protect against avalanches and rockslides, the conveyors run through a 12-km- (7.4-mile-) long tunnel system. The lowest of the three conveyors is equipped with a shuttling head end. With this, the conveyor discharge point can be moved back and forth by 100 m (330 ft), allowing it to build up a longitudinal stockpile at its end. To meet the extreme design parameters, the limits of conveyor design had to be pushed to record-setting marks. For instance, the ST-7800 steel cord conveyor belt is the strongest belt ever installed in a conveyor system. A total drive power of 25 MW (33,535 hp), consisting of 10 2.5-MW (3,352-hp) drives, is included in the design plans. In loaded condition, the electric motors act as generators and feed electric energy back into the power grid. The motors are controlled by variable frequency inverters that provide an infinite adjustment of motor speed. This technology allows starting and stop- ping the conveyors precisely along predetermined acceleration and deceleration ramps. This is done so harmful belt jerking and stress waves can be avoided.

Jan 1, 1999

By R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (K088) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron-and steel making and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By E. Oraby, S. Garcia, A. Thurgood, D. Bertoldi, G. O’Malley

Mining and Process Solutions (MPS) most advanced process, GlyCatTM is the only process that can be easily adapted to existing cyanidation plants in the market today whose real advantages over cyanidation are when treating copper containing ores, concentrates or tailings. With such complex material, GlyCatTM requires 70-90% less cyanide addition to achieve the same precious metal extraction. However, GlyCatTM is not simply cyanidation with added glycine. It is a completely different process where the solution chemistry and conditions needed to effectively leach the precious metals are quite different. Downstream however, the process is largely unchanged as the recovery of the leached gold and silver uses existing known processes such as conventional activated carbon or zinc cementation (Merrill-Crowe process). Another advantage is lower SCN, OCN, WAD and no free cyanide in the effluent which can substantially reduce cyanide detoxification requirements and decrease the OHS and ESG risk of the operation. This paper outline some of these differences and presents testwork, piloting and process examples to highlight the advantageous of this new process over conventional cyanidation.

Feb 1, 2023

By Gregg R. Bierei

Arch of Illinois is a mining complex comprised of two surface and two underground mines located in Perry County, in southern Illinois. The company a division of Apogee Coal Co. of St. Louis, MO. Arch of Illinois' two surface mines, the Captain and Horse Creek Mines, use large stripping shovels and cross-pit bucketwheel excavators to remove overburden from three seams of coal, the Herrin No. 6, Harrisburg No. 5 and Danville No. 7. All are considered high sulfur reserves. The two underground operations are managed by Arch of Illinois. They are the Kathleen Mine and the newly constructed Conant Mine, which began production in 1991. Both underground mines are continuous miner operations. They mine the No. 6 coal, which is about 1.8 m to 2.1 m (6 to 7 ft) thick. All coal is currently transported by truck to a central preparation plant located at the Captain Mine. This preparation plant produces 27 kt/d (30,000 stpd) of clean coal. Production in 1992 reached 5.9 Mt (6.5 million st) of saleable coal. Of that, about 66% or 4 Mt (4.4 million st) are produced by the surface mines and the rest the by under ground operations. Change is in the wind for Arch of Illinois. In 1988, 100% of all production (6.2 Mt or 6.9 million st) came from surface operations. By 1995, only 38% of production is scheduled from surface mines. And by the year 2000, 100% of production will from underground mining methods. Dwindling low ratio reserves, compounded by increasing environmental and land acquisition costs, coupled with more efficient underground mining equipment, have started an evolutionary trend toward development of underground reserves. For Arch of Illinois to maintain profitability of remaining surface reserves and to compete effectively mining underground, it must improve efficiency, productivity and cost reductions. These efforts are essential for maximizing current surface reserves and to ensure a continued existence in the presence of clean air legislation and the softening of the high sulfur coal market.

Jan 1, 1993

By M. L. Free, N. Dhawan, M. S. Safarzadeh, J. D. Miller, M. S. Moats

"The drum agglomeration of nickel laterite and gold ores has been optimized through the design of experiments (DOE) using a Taguchi L16 (45) orthogonal array to determine the optimum conditions for maximizing average agglomerate size and minimizing the amount of fines. The effects of controllable operating factors including moisture content (nickel laterite ore: 34-37%; gold ore: 7-10%), retention time (2-3.5 min), drum speed (15-45% critical speed), drum load (nickel laterite ore: 8-32 %; gold ore: 6-22%) and acid concentration (150-600 g/L) on the performance of the agglomeration process were studied.For nickel laterite ore, maximum average agglomerate size and minimum percent fines (-1 mm) occurred under the following conditions: drum load (23.7%), moisture (36.5%), time (3 min), drum speed (30% critical speed) and acid concentration (150 g/L). Under the studied nickel laterite ore conditions, the most effective parameters for maximizing average agglomerate size and minimizing the amount of fines were found to be drum load and acid concentration, respectively. Drum speed had a statistically significant effect on minimizing the amount of fines. Maximum average agglomerate size and minimum percent fines (-1 mm) for gold ore occurred under the following conditions: drum load (19.3%), moisture (8.5%), time (2 min 15 s) and drum speed (40% critical). The most significant factors for maximizing average agglomerate size and minimizing the amount of fines for gold ore were found to be drum load, time and moisture.IntroductionSeveral heap leach operations have experienced problems in terms of poor recovery due to percolation issues caused by low-grade complex ores, tailings and clayey deposits. Poor percolation can lead to low metal extraction due to solution channeling or the development of impermeable/dead zones within the heap (Dhawan et al., 2012; Kappes, 2005). Improper heap building practices such as the use of loose agglomerates and inadequate attention toward the presence of clay minerals have been among the main reasons for percolation issues. During the transport of ore material, severe segregation of the material can occur. To overcome percolation problems, a major improvement was made through the introduction of agglomeration prior to ore placement. If the ore particles and agglomerates are of similar size, segregation can be avoided to a great extent (Dhawan et al., 2013; Kinard and Schweizer, 1987; McClelland and van Zyl, 1988). Agglomeration improves the uniform percolation of solution through ore heaps and is applicable to many ores, wastes and milled tailings (Bouffard, 2005; Dhawan et al., 2013). Manning and Kappes (2005) reported agglomeration/ stacking accounts for ~14% of the total heap leaching operating cost. The cost of binder is a primary contributor toward the total cost. Also, the lack of consistent quality control tests for agglomerate often leads to operational problems. The details are mentioned elsewhere (Dhawan et al., 2013). Considering the significant contribution of the agglomeration/stacking step toward the total heap leach operating cost, it is appropriate to study the agglomeration behavior and its optimization for two different ores. The reason to study the same parameters for different ores is the fact that significant variability in the agglomeration behavior of different ores has been reported to exist in industrial operations."

Jan 1, 2015

By M. Moats, I. E. Paschalidou, K. Awuah-Offei

Tellurium (Te) is a rare metalloid that is predominantly produced from the treatment of anode slimes formed during copper (Cu) electrolytic refining. The US Government lists Te as one of the 50 critical minerals, partly, because of its use in thin-film photovoltaic (PV) technology. Given policy initiatives to increase Te production, it is important to evaluate the life-cycle environmental impacts of Te recovery as a by-product of Cu processing. The literature contains a few specific life cycle assessment (LCA) studies of groups of metals that include Te without proper regard to impacts per life-cycle stage of Te production or the effect of allocation on the results. This study builds an LCA model of the production system of Te from anode slimes treatment to evaluate the effect of allocation on life-cycle impacts. We build life cycle inventories using data from the Ecoinvent v3.7.1 database, literature, and engineering calculations and allocate impacts in proportion to products’ mass and economic value. The results show that economic value-based allocation yields greater impacts than mass-based allocation indicating the significant effect of the allocation approach on life-cycle impact estimates.

Feb 1, 2023

By K. L. Gabby

Since mercury is chemically similar to silver, it tends to dissolve along with the silver and gold during cyanide leaching. Ultimately mercury is recovered along with the silver as mercury/silver/gold amalgam which requires retorting to remove the mercury prior to refining the silver and gold. A possible approach to separating mercury from silver and gold in cyanide leach solutions is to take advantage of the replacement reaction between [Hg(CN)4]2- and Ag2S, which results in precipitation of mercury as HgS while dissolving silver as [Ag(CN)2]-. Results are presented demonstrating that mercury can be removed from cyanide solutions with high effectiveness, while, at the same time, recovering additional silver in solution. Initial experiments with static flasks in the laboratory showed a high degree of mercury removal could be achieved. Results using actual metallurgical plant products in bottle roll tests indicate the process works on a larger scale, but also results in significant gold losses if the solution being treated has high gold levels, such as carbon stripping pregnant eluent solution.

Feb 23, 2014

By W. C. Hirt

Deposits of ferromanganese crust containing cobalt and nickel occur on the seafloor in the Pacific Ocean near the Hawaiian Islands and Johnston Atoll. This paper describes developmental flotation metallurgy to separate crust from its associated substrate gangue. Important variables in ferromanganese crust flotation include reagent type, aeration rate, conditioning time and agitation intensity, pH, temperature, water type, and feed size distribution. Flotation in seawater of minus 600 ~m (-28 mesh) material assaying 6.2% Mn, 0.2% Co, and 0.13% Ni with diesel fuel-crude tall oil-sulfonate collectors produces concentrates assaying 15% Mn, 0.6% Co, and 0.3% Ni with recoveries of 89-95% while removing 62% of the feed weight.

Jan 1, 1990

By S. Lu, J. P. Barta, T. W. Meikle

Three nutrient amendments and a biological seed inoculant were evaluated for use in establishing vegetative cover on waste rock substrates. Randomized blocks were placed on three substrates. Treatments included two types of organic fertilizer, mineral fertilizer, Azospirillum bacterial inoculant, plus controls. The seed mix consisted of native grass species adapted to low nutrient conditions. Canopy cover has been monitored for three growing seasons. Results indicate : 1) two of three substrates support plant growth following amendment with organic fertilizers; 2) organic fertilizers increase cover substantially over mineral fertilizer; and 3)Azospirillum had no effect on canopy cover.

Jan 1, 1999

By Subhas G. Malghan

The response of feldspar flotation to tallow diamine dioleate collector in the presence of sulfuric acid is studied using batch flotation experiments. Application of this non-hydrofluoric acid (non-HF) reagent system in the flotation of mineralogically and chemically different feldspar ores is compared with that of the conventional hydrofluoric acid system. The dependence of flotation recovery and concentrate grade on feed particle size distribution, conditioning time, pulp density, and pH, combined variation of collector and acid addition rates, sodium hydroxide concentration in the collector solution, and initial pulp pH prior to conditioning is studied. The results have been discussed in relation to applicability of the non-HF system to plant trials, and the nature of the collector adsorption in the selective flotation of feldspar.

Jan 1, 1978

By B. K. Cantrell

The use of diesel equipment in underground coal mines is controversial because "whole diesel exhaust" is regarded as "a potential occupational carcinogen" by the National Institute for Occupational Safety and Health (NIOSH). Threshold limit values (TLVs) are recommended for the gaseous pollutants; CO, CO2, NO, NO2, SO2' and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols. The University of Minnesota and the Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines using diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality.

Jan 1, 1991

By Roshan B. Bhappu

Stimulated by current $0.80 to $1.20 per pound price tag of copper, considerable interest and activity have been generated in the copper mining camps throughout the world, and especially in the Southwestern United States and Northern Mexico copper belt. Under these economically favorable conditions, many of the marginal oxide-copper deposits, as well as newly discovered prospects, are under scrutiny for possible exploitation. For both the known deposits and new prospects, the big question facing the mine operator is the selection of the best method for processing these economically attractive oxide-copper deposits. Several variations of the hydrometallurgical processes are currently available for treating oxide-copper ores which can be mined by the open-pit method. Basically, these processes involve preparing the ore for application of an acid solution, applying the solution to the ore, and recovery of the metal from the pregnant solution. Dump leaching, heap leaching, vat leaching, agitation leaching and, in more recent times, in situ leaching or solution mining in combination with well established cementation process or the newly developed solvent extraction-electrowinning system have all been employed or have been investigated for the recovery of copper from oxide ores. Of these processes, dump, heap and vat leaching have been successfully practiced for treating oxide-copper ores. Agitation leaching is a relatively newcomer and has been adopted from the experiences of uranium and gold processing. Finally, the inplace leaching technique is the latest process to be suggested for possible treatment of oxide-copper ores.

Jan 1, 1974

By L. J. Vincze

The program of study of pellet binder materials was begun by the ORF in 1963 to examine various Canadian materials as substitutes for bentonite which is imported in large tonnages (199,270 tons in 1969) from the U.S.A. for Canadian pellet plant operations. Most of the raw bentonite used in Canada originates in Wyoming, North Dakota and more recently Greece, resulting in relatively high transportation costs to pellet producers. Some Canadian bentonites available in Western Canada (Alberta) can be beneficiated for uses as pellet binders but could not compete in cost with U.S. sources due to the cost of beneficiation and the higher rail transport charges to Eastern Canada. It is difficult to find a substitute for bentonite, and many materials have been investigated by research groups but, so far, no economic substitute is in use. However, some success is apparent in studies of low cost materials such as clays, sea weed, peat moss and low grade coal, The work done by the ORF over several years has covered systematic test¬ing of Ontario clays, lignite, some types of tree bark, waste sulphite liquors of various kinds, and peat moss as binders for iron ore pellets. The major effort has been concentrated on peat moss and has included a study of the influence of different additives. Since analysis of peat moss for humic acid is difficult and time consuming, a certain amount of time was devoted to development of improved methods, the most useful of which was a spectrophotometric method based on extraction of peat by sodium pyrophosphate for determination of humic substances. In the present paper, only the most recent work concerning the use of peat moss with suitable additives is discussed in detail, since it is the most conclusive and best documented portion of the program.

Jan 1, 1971

By I. WILKOMIRSKY, J. BECKER, F. Parada

Purification of molybdenite concentrate from copper concentrates was performed by sulfation. The sulfation of molybdenite concentrates was carried out with pure sulfuric acid (> 96%) at 160–190 °C to study the influence of the reaction temperature and reaction time on the residual copper in the molybdenite concentrates. A purified concentrate with less than 0.1 wt% copper and low levels of other metals were obtained. For up to 7.1 wt% copper, the conditions required are a temperature of 190 °C, a reaction time of 14 h, and a moly/acid weight ratio of 1/1. Furthermore, several designs of sulfation reactors were evaluated in order to obtain the desired level of copper in the product and to analyze the influence of the operational and design parameters on the reactor dispersion number (Le). The basic design for an 80-t/day plant fed with 4 wt% copper molybdenite concentrate requires five backmixed reactors in series, each measuring 8 m3, operating at 190 °C and with a reaction time of 10 h. The reactor must be protected against severe corrosion by the hot sulfuric acid with either Teflon, glass or ceramic.

Jun 14, 2022

By W. W. McClintock

A column flotation system was designed to conduct release analyses of a very finely disseminated, stratiform, copper ore from the Denali Copper Prospect, Alaska. Chalcopyrite is finely disseminated in a carbonate matrix and pyrite is disseminated in both the chalcopyrite and gangue, requiring grinding to 20 microns for adequate liberation. A 25 mm x 2.4 m glass flotation column was designed. The ore and its flotation tailings were repeatedly floated to obtain a rougher concentrate, which was repeatedly floated to produce release fractions. These were analyzed for copper, iron calcium and magnesium. Release curves were plotted. The procedure was replicated at each of two grinds; 99% and 88% passing 37 microns (400 mesh), and should find application for flotation characterization and process selection. Bond grindability work was also conducted.

Jan 1, 1994

By A. G. Fonseca

The effects of coal cleaning, coal combustion and flue gas particulate removal systems on the partitioning of 12 trace elements were investigated. This study was prepared to help document the fate of trace elements in modern coal preparation plants and coal-fired utility boilers. The coal cleaning data were obtained from several coal preparation plant operations. The CONSOL 1. 5 MM Btu/hr pilot combustion and electrostatic precipitator (particulate removal system) test facility was used to develop the combustion systems data. A comparison with the very limited amount of published data from utility boilers is presented.

Jan 1, 1993

By O. Ozdemir

Soda ash, an essential raw material for major industries, such as the glass, chemicals, soap and detergents, pulp and paper, mining and water treatment industries, is traditionally produced by chemical and thermal treatment of trona ore. The treatment processes for trona ore are not only chemically expensive but also energy intensive. Hence, the production of a high-purity trona concentrate at a lower energy and operating cost is of considerable interest to the trona industry. In this study, we describe a possible two-stage process for concentrating trona ore, involving dry magnetic separation followed by flotation, to remove insoluble impurities from the trona ore. The results showed that a trona concentrate of 91.7% purity with a recovery 91.1% can be obtained by two-stage magnetic separation, which could be further improved to 98.1% purity at a recovery of 83.8% by subsequent flotation of the non-magnetic trona product. The purity of trona concentrate is limited by the particle size and impurity content of the trona ore. The operating parameters for magnetic separation and flotation have been identified to obtain an acceptable quality concentrate.

Jan 1, 2011

Fundamental results obtained from research on the properties of the edge surfaces of kaolinite particles (~500 nm) are reported. Of particular significance was the development of the experimental protocol. Well-ordered kaolinite edge surfaces were prepared as an epoxy resin sandwich structure having layered kaolinite particles in the center of the epoxy resin sandwich. Images of the sectioned kaolinite edge surfaces were examined by atomic force microscopy (AFM), and the average thickness of kaolinite particles in this study was determined to be 38.3 nm ± 11.7 nm. Furthermore, the surface charge of the kaolinite edge surfaces was evaluated with a super sharp Si tip. The point of zero charge (PZC) of the kaolinite edge surface was determined to be below pH 4, in contrast to the traditional view that the edge surfaces of kaolinite particles may carry a positive charge at pH 4. This lower PZC of the kaolinite edge surface was attributed to the lack of isomorphous substitution in the silica tetrahedral layer when compared to the PZC for the muscovite edge surface. Our results are consistent with the particle aggregation and flotation behavior of kaolinite, and should provide the basis for improved flotation strategies leading to the efficient recovery and utilization of mineral and energy resources.

Feb 23, 2014

By Laszlo Valentyik

Heavy media separation (HMS) is one of the most widely used gravity methods in the mineral industry. The feed is separated, according to the specific gravities, into two products; float (light) and sink (heavy) particles. The universal acceptance of the process is due to simplicity, efficiency and robustness for ease of control. However, if optimum separation is desired during the operation of heavy media plants, a delicate balance of a number of variables is essential. Among the variables, the two which are generally the most frequently checked and controlled are specific gravity and consistency of the medium. The latter is a function of the settling rate of the media. The medium is generally made up of finely ground ferrosilicon, magnetite, galena, shale, quartz sand, clay contaminants and water. The frequently present clay in the medium acts as a stabilizing agent, since the coarse heavy medium solids (called media) would quickly settle if they were mixed only in water. Clay concentration of the medium varies between 3-7% by height (1,2). Although clay is essential for reasonable media stability, clay concentration greater than 7-8% imparts too high a viscosity to the medium, and the feed cannot accurately stratify and therefore separate into the required products. To be on the safe side, plant operators clean the medium from most of the clays, and would rather work at a lower stability than have a very viscous medium on their hands. The most recent advance in the area of consistency control rlas made by the introduction of atomized (spherical) ferrosilicon (3). This extended the upper limit of the use of ground ferrosilicon from 3.3 to approximately 3.6, broadening the range of the optimum operating conditions. A viscosity control method was also worked out by the use of low cost additives which lower viscosity while retaining a favorable low setting rate (4). Recently (5) polymers have been successfully used in oil well drilling muds then the requirements were mainly to suspend and transport cuttings during the periodic shutdowns and dril1ings respectively. The rheological properties of these polymer suspensions are such that they present an infinite viscosity to

Jan 1, 1971

By F. Turatti

Rio Tinto is one of the world's largest mining companies, involved in every stage of metal and mineral production, producing aluminium, copper, diamonds, coal, iron ore, uranium, gold and industrial minerals. Operations are in more than 50 countries in multiple continents and vary in location between large urban centres, regional industrial complexes and remote regions. A risk-based strategy was developed by Rio Tinto to manage its air quality impacts on a global scale. The strategy consists of three objectives ? improving air quality performance, developing industry leading practices and engaging and influencing in air issues. This paper discusses three major successes achieved this approach. Firstly, how air shed resources are managed in constrained air sheds. Secondly, how financial modelling is used to value air quality constraints, and thirdly, how a rigorous and comprehensive e-learning course is used to improve the overall level of air management knowledge of Rio Tinto?s environment managers.

Feb 27, 2013