Search Documents

By Sunil Vytla, Agus Sasmito, Akash Adhikari, Srivatsan Jayaraman Sridharan, Purushotham Tukkaraja

Previous studies on blast fumes (carbon monoxide and nitrogen dioxide) clearance and workplace reentry time have overlooked the effects of toxic gases trapped in the muck pile. The currently available models for calculating the mine reentry times assume that all post-blast fumes are emitted upon detonation. However, recent studies reported that as much as 60 to 70% [1–5] of the fumes or gases produced during an underground development blasting could remain trapped in the adjacent rock mass or in the muck pile. Trapped fumes are slowly released [1–5], and when disturbed, high concentrations are released, representing a possible risk during the loading and transportation of the muck pile. In this study, mathematical models were developed using computational fluid dynamics to understand the behavior of the trapped fumes and their effect on mine reentry time. The three scenarios considered for this study include (i) gas emission source with no muck pile volume, (ii) gas emission source with non-porous muck pile volume, and (iii) gas emission source with porous muck pile volume. The estimated reentry times in all three scenarios were compared to see how porous media affects dilution time. It was observed that scenario 3, with fumes trapped in the muck pile, took a significantly longer clearance time (more than double) as compared to scenarios 1 and 2.

May 17, 2022

By H. Yen, D. E. Walsh, H. K. Lin

"Comminution circuits are widely used in nonferrous and precious metals milling. Steel crushers, grinding mills and grinding media are typically used in comminution circuits. Comminution circuit wear products, in the form of metallic iron (steel) fines, are unavoidably produced and report to undersize products in the classification circuit, i.e., flotation or leach feed, while tramp grinding steel (TGS) reports to classification oversize products and returns to the grinding mill, building up in the circulating load. In laboratory studies, TGS reduced grinding efficiency significantly, the impact being dependent upon the size of the TGS present in the mill. Because iron fines adsorb flotation reagents effectively, iron fines increase reagent consumption and reduce flotation recovery. Iron fines are also capable of reducing gold recovery in cyanidation circuits via a cementation reaction. When using filtered gold solution from the cyanidation circuit of an Alaskan gold mine, the gold concentration in solution was reduced by 0.2 to 2.6% over various reaction periods when iron fines were present in the solution.IntroductionComminution circuits are widely used in copper, lead, zinc, nickel, cobalt, molybdenum and precious metal mills. Flotation and leaching processes are usually preceded by comminution (crushing and grinding) circuits in order to liberate valuable minerals for effective separation, concentration or dissolution by the subsequent flotation or leaching processes.Steel crushers, grinding mills and grinding media are typically used in comminution circuits. Comminution circuit wear products, in the form of metallic iron (steel) powder, are unavoidably produced and report to undersize products in the classification circuit (flotation or leach feed), while tramp grinding steel (TGS) reports to oversize productions during classification and returns to the grinding mill, building up in the circulating load. Variables affecting the amount of metallic iron powder and TGS produced in a comminution circuit include ore hardness, grinding mill operating conditions, comminution circuit design and the metallurgy of the steel used for manufacturing crusher liners, mill liners and grinding media. As one example, a comminution circuit product of 80% passing 200 mesh at the Pogo Mine, AK is estimated to contain approximately 2 kg/t of metallic iron. A finer grind will generally produce a comminution circuit product with higher metallic iron fines content."

Jan 1, 2015

By O. Babak, O. Leuangthong, M. A. Cuba

Integration of data from multiple sources and/or multiple scales is a common, yet challenging aspect of geostatistical resource modeling. Common approaches to data integration are based on a cokriging framework that assumes a consistency of scale in the information that leads to a requirement to composite the data prior to model construction. It is well known that the geostatistical model parameters are scale dependent. In particular, the volume variance of integrating these various scales has a direct impact on the semivariogram that should be used in model construction and/or the assessment of volume-variance relations as it affects resource estimation. This paper reviews and compares two different approaches for semivariogram upscaling. The first approach is the scaling laws. It is an empirically derived approach, involving several simplifying assumptions, one of which is a strict assumption of invariance of the semivariogram shape. The second approach is a theoretically derived direct upscaling of the semivariogram. This approach has been around for a number of years, but is seldom implemented due to software limitations. In this paper, we present a numerical integration approach to facilitate direct semivariogram upscaling. The advantage of direct upscaling over the scaling laws approach is shown by considering a synthetic example and a case study. Further, in the case of multiple codependent random variables, the extension of the direct semivariogram upscaling to the cross semivariograms is derived and an upscaled consistent linear model of coregionalization is presented.

Jan 1, 2013

By Xiaolong Bi, Shaohua Luo, Longjiao Chang, Shiyuan Cao, Jianan Liu

iliary agent was proposed. The mineralogical transformation and silicon extraction kinetics of laterite nickel ore in alkaline hydrothermal treatment were studied. The effects of reaction temperature (175 ~ 250℃), molar ratios of sodium hydroxide to ore (1.05 ~ 1.2:1), and laterite nickel ore particle size (44 ~ 178 μm) on the extraction ratio of silica were investigated by using the shrinking core model. The results show that the extraction ratio of silica increases with the increase of reaction temperature, sodium hydroxide to ore molar ratio, reaction time, and the decrease of raw ore particle size. The kinetic analysis shows that the separation of silica in laterite ore can be described by internal diffusion model. The apparent activation energy (Ea) of the reaction was 8.87 kJ mol− 1, and the kinetic modeling was established.

Dec 2, 2021

By Erik Klohn

The El Soldado copper deposit occurs in volcanic rocks of alkaline affinity of Lower Cretaceous age. The orebodies are discordant and show strong structural and lithological control. The mineralizing event was accompanied by hydro- thermal alteration expressed as carbonatization, silicification, and chloritization. Individual orebodies contain bornite-chalcopyrite cores which are surrounded by haloes dominated by chalcopyrite and pyrite respectively. The sulfur isotope composition of copper sulfides strongly suggests the sulfur is of magmatic origin. Fluid inclusion studies show the mineralizing fluid to be a highly saline NaC1-CaC12, brine. No evidence of boiling was found. The deposit is most likely of epigenetic origin. Hydrothermal fluids were produced during crystallization of a sodium rich trachytic magma during the waning stages of an episode of alkaline magmatic activity. Similar copper deposits along the Chilean Coastal Range may also be associated with alkaline host rocks.

Jan 1, 1986

By E. Tarshizi

Research was conducted to develop a simulation and animation model for an aggregate (sand and gravel) mine operation. This model can assist the mine engineers to investigate and consider the various options of haulage systems which are critical for the mine operation productivity. Discrete-event system simulation studies can be used for the typical haulage issues that mining engineers are often faced with: using truck fleet haulage, conveyor belts, or a combination of both. The simulation has identified some strengths and weaknesses in the current loading and hauling fleet of the mine, and has resulted in some suggestions for improving the system. The simulation includes animation of the operation. Animation is needed to enhance the benefit of any mine simulation model. By combining the visual power of animation with a mine simulation, a complete picture of the mine system is obtained and displayed. The mine is modeled and animated using GPSS/H® and PROOF Professional®, both of which have shown great applicability in discrete mining simulation projects.

Feb 23, 2014

By B. M. Davis

Characterizing exploration prospect potential has aspects that differ from those encountered during ore reserve estimation. One problem is determination of the ore reserve potential prior to acquisition of significant volumes of hard data. The evaluation is subjective and data are usually sparse and of uncertain quality. However, estimations of the ore reserve potential are commonly demanded by management before project funding will be approved. The estimations from several prospects, along with the uncertainties inherent to the estimation, are then used to compare and contrast the potential of several prospects, often with widely varying geologic models.

Jan 1, 1990

By Erik Westman, BEN WESTON, SETAREH GHAYCHI AFROUZ, KATHRYN DEHN

One of the most difficult challenges in underground mining is to forecast significant seismic events prior to their occurrence in order to support the safety of miners and to minimize damage to the underground operation. Passive seismic tomography is a tool to image the seismic velocity changes in a rockmass, which can potentially reveal the rockmass behavior before and after a significant seismic event. In this paper, the changes in seismic velocity of the rockmass before and after three major seismic events are investigated to determine whether there are identifiable precursory velocity changes associated with the major seismic events. Conventional mechanics imply that the induced stress at the hypocenter would continue increasing until failure, in the form of an induced seismic event, occurs. With passive seismic tomography we can image changes to the seismic wave velocity distribution within a rockmass and hence infer the changes to the induced stress near the hypocenter. This paper evaluates the hypothesis that induced stress at the hypocenter (as inferred by the p-wave velocity) increases until the seismic event occurs. In addition to analyzing p-wave velocity changes near the hypocenter, changes to the p-wave velocity at “zone centers” were also analyzed. These “zone centers” are regions within the rockmass that consistently have a p-wave velocity that is much higher than the average p-wave velocity for the rockmass. It is found that the p-wave velocity did not increase at any of the three hypocenters prior to the seismic event occurring, however the p-wave velocity did increase in the closest “zone center” for two of the three events.

Oct 12, 2020

By J. W. MacDonald

Two coal mine shafts recently completed in Franklin County, Ill., afford experience and accomplishment to warrant review, These shafts provide access to a tract with a potential recovery of one hundred million tons. This work provided the initial sinking by other than a contractor's organization since 1918. Four additional shafts required during the interim were sunk under contract arrangement with others. Supervisory contact and inspection afforded experience to govern planning and conduct of the recent work.

Jan 1, 1960

By N. Dashbold, E. Rudnik

"Waste electric and electronic equipment currently comprises the fastest-growing waste stream in the world, but at the same time it is seen as an important source of metals for the recycling industry. E-waste is usually treated pyrometallurgically, with hydrometallurgical methods used to a lesser extent. This paper reports the results of research on the selective recovery of copper from smelted low-value electronic waste. Pyrometallurgical pretreatment of the scrap allowed the removal of plastics and the increase of metal content in the material. The obtained alloy of copper, zinc, tin and silver was a multiphase solid consisting of two brass phases and inclusions rich in iron, lead and silver. Copper alloy was further anodically dissolved in ammoniacal chloride solution. It resulted in high degradation of the material and accumulation of the metals mainly in the slime. The slime was then leached in acid or ammoniacal chloride and sulfate solutions followed by selective copper electrowinning. Hydrochloric acid was the most efficient solvent for the slime, but ammoniacal solutions were more selective for copper. Copper could be leached with 96 to 100 percent and 87 percent efficiency from the slime by the chloride and sulfate solutions, respectively. Copper with 90 to 99 percent purity at current efficiency of 42 to 76 percent was obtained from the acid solutions, while copper with 98 to 99 percent purity at current efficiency of 60 to 86 percent was deposited from the ammoniacal baths. IntroductionObsolete electrical and electronic equipment makes up the fastest-growing waste stream in the world (Baldé et al., 2015), due not only to the introduction of wider ranges of new types and models of a variety of electronic products but also to the shortening of their life-spans, sometimes referred to as planned obsolescence by producers (Keeble, 2013). About 42 million tons of electronic waste, or e-waste, are estimated to have been generated globally in 2014 (Baldé et al., 2015), and it is expected that in the European Union alone the waste electrical and electronic equipment (WEEE) stream will reach more than 12 million tons by 2020 (European Commission, 2015). Accurate evaluation of e-waste generation (Wang et al., 2013) and its global transport (Breivik et al., 2014) is difficult, mainly due to a lack of high-quality data related to its market and socio-economic dynamics.Many countries introduced legislation to control e-waste flow, collection and recycling. For example, Directive 2012/19/EU on waste electrical and electronic equipment (European Parliament and the Council of the European Union, 2012) obliges all E.U. members from 2016 to maintain a minimum collection rate of 45 percent of the total weight of WEEE collected. From 2019, the minimum collection rate to be achieved annually shall be 65 percent of the average weight of electronics placed on the domestic market in the three preceding years, or alternatively 85 percent of WEEE generated in the territory of the particular member."

Jan 1, 2017

By Frank E. Sullivan

The separation of liquids from granular materials has been widely studied by a number of: investigators over a period of years in an effort to more fully understand the physical phenomenon which occurs. Liquid may be removed from solids, or partially removed, by gravity separation, mechanical separation' or heat drying. Mechanical separation is advantageous when compared to heat drying principally from a cost saving standpoint and also on certain materials which are heat sensitive. It is realized however that mechanical separation of liquids has certain practical limitations. In order to evaluate the efficiency of mechanical separation and predict the extent of, liquid removal, it is first necessary to study the forces which hold the liquid to the solids. From a very practical observation using gravity drainage, it is soon obvious that a pile of coarse solids will drain faster and retain less liquid than a pile of finely divided solids of the same material. For commercial operations it is important to estimate the residual liquid which will remain after a mechanical separation. Batel (1) explored the various quantities of liquid present in the interstices of the bulk granular material. From his work and other authors which he has correlated in one of his recent papers, various formulas are now available which permit an empirical relationship to be developed showing residual moisture versus mechanical separating forces.

Jan 1, 1965

By Ronald M. Hays

The White Pine Copper Division of Copper Range Company is a large copper producer operating an underground mine, mill, and smelter on Michigan's Upper Peninsula. Principal water discharges are from the tailings basin where these discharges are high in dissolved solids because of mine water pumped into the basin. Principal air emissions are from the smelter where SO2 emissions are uncontrolled. Although water discharges and air emissions have not had significant environmental impacts, environmental regulations could require additional control procedures. Because of low copper prices and poor profitability, cost of compliance with possible new environmental regulations could have serious impact on White Pine with no apparent significant beneficial environmental impacts.

Jan 1, 1979

By Luzheng Chen

The study aimed to evaluate the separation performance of a full-scale continuous centrifugal concentrator in the reconcentration of fine hematite from high-gradient magnetic separation (HGMS) concentrate in a tailings recovery plant, and to investigate the usefulness of the technology in industrial applications. The effect of changing the operating variables on concentrate grade and recovery was studied. The results indicate that among the variables considered in the study (water spray pressure, centrifugal acceleration, feed volume flow rate, feed percent solids and the reciprocation and spacing of water sprays), the change in centrifugal acceleration affects the recovery the most and continuous concentration can be achieved only when the water spray has a sufficient pressure. In addition, the reciprocation and spacing of the water sprays have a significant influence on the concentrate grade. Although performance of the full-scale concentrator is slightly inferior to pilot-scale trials, due to limitations in the scale-up design and the fluctuations of feed material characteristics, this concentrator provides a potential way to achieve continuous concentration and obtain a high-grade concentrate from tailings.

Jan 1, 2010

By E. W. Greig

This paper is an account of exploration for bauxite in the Amazon Basin, Brazil, and particularly of the discovery, exploration and development by Alcan of the Trombetas deposit so a general account of the Trombetas Project has already been published in E/MJ (Anon. 1975) to which the reader is referred for details on owner-ship, infrastructure and construction as well as the proposal for mining and treating the bauxite. It is impossible to consider the Trombetas deposits in isolation. A regional account of bauxite in and around the Guyana Shield and the northern portion of the Brazilian Shield is included and it is suggested that these deposits all formed during Tertiary time under similar conditions.

Jan 1, 1977

By Jack G. Crump

Nuclear radiation systems for gauging solids content in process slurries and level in crushers has demonstrated acceptance in ore processing. The use of nuclear radiation for moisture analysis of bulk materials is presently receiving acceptance in beneficiating and agglomerating processes. On the horizon is the use of nuclear activation methods for continuous, qualatative and quantitative analysis of concentrate. The common characteristics of these uses of radiation is the non-contacting nature of the measurement. Unquestionably, this is the dominant reason for acceptance of nuclear methods in level and slurry-gauging. Moisture activation analysis of a product using nuclear methods retain this advantage. However, and: more importantly, they offer new solutions to old problems. The nuclear method in addition to being non-contacting, is non-destructive and provides a continuous measurement of the process variable. The system responds: to the fundamental makeup of matter, mass and elemental composition, not to secondary properties such as temperature, resistivity, or dielectric constant. Measurement is a volume rather than a surface phenomenon, thus the results can provide a truer pricture of the measured variable.

Jan 1, 1965

By Y. Akin, M. Hancer, M. S. Celik, J. D. Miller

Flotation pulps with boron minerals such as colemanite and borax using primary amine collectors, e.g. dodecylamine, exhibit collector precipitation above a critical pH depending on the amine concentration. This was earlier attributed to the formation of a mine hydroborate. However, results from this current study indicate that the precipitate is dode-cylamine, rather than dodecylamine hydroborate. A systematic study involving solubility, zeta potential, microflotation, adsorption, and surface tension measurements is presented to elucidate the role of a mine precipitates in boron flotation systems.

Jan 1, 2000

By Clement K. Chase

Since the dam of cyanidation leaching techniques for precious metals, certain manganese-bearing silver ores have been a problem due to low silver extractions. Since simultaneous occurrence of silver and manganese is common in nature, this situation has made many otherwise attractive silver deposits uneconomic in the past. Several older techniques have been useful but at $1.29 per ounce of silver, the economics were unfavorable. With the new look in silver prices and some improvements in processing technology, neglected silver districts offer new promise.

Jan 1, 1981

By R. J. Nankee

Coal is our most abundant, low cost energy resource. Expansion of its use is being challenged due to "SO2 emission" regulation with even more restrictive legislation pending. High quality coal reserves are becoming more limited due to greater use in recent years. Aids to allow more use of coal in today's environment include beneficiation of coal before combustion and scrubbing the emissions from coal during combustion. Dow's efforts to help meet these challenges by beneficiating coal include true heavy media gravity separations with chlorinated solvents and liquid/liquid partitioning processes and "Dow Solvent Recovery Technology" to recover the solvent from product (or floats) and rejects (sinks), The objectives of the efforts to clean coal are to reduce sulfur and ash. In this paper, the solvents will be described; a general flow diagram presented; some of the results on upgrading various coals will be described, and projected costs of full-scale plants using chlorinated solvents will be compared to conventional cleaning plants.

Jan 1, 1985

By L. Zhou, A. Martikainen, G. Goodman

Continuous airflow monitoring can improve the safety of the underground work force by ensuring the uninterrupted and controlled distribution of mine ventilation to all working areas. Air velocity measurements vary significantly and can change rapidly depending on the exact measurement location and, in particular, due to the presence of obstructions in the air stream. Air velocity must be measured at locations away from obstructions to avoid the vortices and eddies that can produce inaccurate readings. Further, an uninterrupted measurement path cannot always be guaranteed when using continuous airflow monitors due to the presence of nearby equipment, personnel, roof falls and rib rolls. Effective use of these devices requires selection of a minimum distance from an obstacle, such that an air velocity measurement can be made but not affected by the presence of that obstacle. This paper investigates the impacts of an obstruction on the behavior of downstream airflow using a numerical CFD model calibrated with experimental test results from underground testing. Factors including entry size, obstruction size and the inlet or incident velocity are examined for their effects on the distributions of airflow around an obstruction. A relationship is developed between the minimum measurement distance and the hydraulic diameters of the entry and the obstruction. A final analysis considers the impacts of continuous monitor location on the accuracy of velocity measurements and on the application of minimum measurement distance guidelines.

Jan 1, 2012

By T. A. de Almeida, M. de Paiva Bueno, M. Powell

The mining industry is one of the foundations of modern society, providing not only the raw materials needed to maintain a contemporary lifestyle, but also serving as a basis for the development of future technologies. From the most basic components of an appliance to the materials needed to design an electric car or a space rocket, each raw material has gone through a painstaking procedure of extraction and processing, and ways to make this process more efficient will be of great help to meet an ever-increasing demand for minerals. One of the biggest challenges when extracting mineral resources is to measure the variability of the mineral body prior to processing. Comminution is the most power-demanding stage, and the lack of geometallurgical testing, often for financial reasons, may result in an inefficient operation. The Geopyörä Rock Breakage test was developed with the objective of making mineral variability data more accessible by providing both standard comminution parameters and rock mechanical properties at low cost, and with a modest sample size, allowing a larger number of samples to be tested to reduce uncertainties and assure productivity. The objective of this paper is to present the results of an extensive validation of this new rock breakage method against two of the main tests currently in use, namely the SMC® and Bond ball mill work index tests. More than 100 samples have been tested and the results compared, showing that the new method can accurately estimate the parameters of the traditional tests. This confirms that the new test is a reliable tool for comminution and geometallurgical tests.

Feb 1, 2023