Search Documents

By John H. Canterford

The adsorption of uranium onto Wyoming bentonite was measured in carbonate media over the range pH 8-11. Uranium was removed from solution onto the solids by a rapid reaction, proposed to be adsorption of the anionic uranyl tricarbonato complex onto edges of the clay platelets, and a slow reaction which may be precipitation of a hydroxide. The changes in uranium content of the aqueous and solid phases of a uranium ore carbonate leach slurry were also measured as the slurry was progressively diluted. There was an increase in the uranium content of the solids as the pH of the suspension was lowered, as was observed with the Wyoming bentonite. The results indicate the conditions that should be met with respect to pH control in order to prevent the problem of excessive uranium adsorption in the counter-current decantation washing circuit of a conventional leaching process, as well as in the leaching and restoration phases of carbonate solution mining.

Jan 1, 1983

By Z. Hyder, A. Urquidez

"INTRODUCTION The Waste Isolation Pilot Plant (WIPP) is located approximately 26 miles southeast of Carlsbad, New Mexico and is the nation’s first underground geologic repository for transuranic (TRU) and TRU-mixed waste (see Figure 1). The WIPP facility was opened for operation in 1999 when the first TRU waste shipment arrived at the WIPP facility for disposal.WIPP facility does not employ typical production aspects of a conventional mine. Instead, the mining focus is on the quality of the excavation to ensure safe disposal of TRU and TRU-mixed waste (Walls, 1991). GEOLOGY WIPP underground repository is mined within a 2,000 feet-thick bedded-halite formation (Salado Formation) (see Figure 2). The WIPP underground repository is located approximately 2,150 feet beneath the surface near the center of the Salado Formation. Geologic criterion and site-selection factors evaluated for the selection of the repository included topography, depth, thickness, lateral extent, lithology, stratigraphy, structure, erosion, dissolution, subsidence, surface water, aquifers, hydrologic transport, climatic fluctuations, manmade penetrations (U.S. Department of Energy, 1980).FACILITY DESIGN Profit did not play a major role in the WIPP’s conception like in a conventional mine. This was due to the extensive amount of additional regulations and safety controls that had to be built into the WIPP facility. Since it is nuclear and hazardous waste disposal facility, it must meet certain federal and state requirements for TRU-mixed waste. One of the major regulatory drivers for the WIPP facility is defined in the WIPP Land Withdrawal Act (LWA). One of the requirements in the WIPP LWA requires the DOE to submit documentation of continued compliance with Title 40 CFR Part 191, Subparts B, and C. These standards are regulated by the Environmental Protection Agency (EPA). The DOE must submit documentation of continued compliance (recertification) with these regulations every five years. In addition to the LWA, the Resource Conservation and Recovery Act (RCRA) is another major regulatory driver for the WIPP facility. Since the WIPP facility is categorized as a “Miscellaneous Unit” under 40 CFR, it must meet extensive environmental performance standards. These standards are defined in the WIPP Hazardous Waste Facility Permit (HWFP). The HWFP defines the terms and conditions that the Secretary of the New Mexico Environment Department has determined necessary to protect human health and the environment (U.S. Department of Energy and Nuclear Waste Partnership LLC, 2015)."

Jan 1, 2017

By S. D. Van Nort

The Grasberg porphyry copper-gold deposit of Freeport Indonesia Inc., an 81% owned subsidiary of Freeport-McMoRan Inc., lies within the Ertsberg Mineral District in central Irian Jaya, Indonesia. The Grasberg deposit was discovered during a drilling campaign initiated in early 1988. Production at the open pit Grasberg deposit commenced in December 1989. The Grasberg copper-gold orebody is contained with a young igneous complex of dioritic composition which intrudes limestones of the Tertiary New Guinea Group. Alteration is typical of porphyry copper deposits worldwide except that higher grade primary chalcopyrite with significant gold values is associated with a centrally located zone of strong quartz stockwork.

Jan 1, 1991

By W. Hustrulid

"In recognition of his inspiring dedication to the mining industry through education, research contributions and dissemination of practical knowledge, exceptional leadership and excellence in mining engineering practice and for his lecture, “You can't make a silk purse out of a sow's ear.” Recipient of the 2002 D.C. Jackling Award Introduction It is always difficult to decide on the most appropriate title to give to a paper or talk. It is a particularly difficult decision in the case of the Jackling Lecture, because the title becomes part of the award citation. I hope that the significance of this unusual title will become crystal clear as you read the pages that follow. However, to assist you in this journey, I will provide the following few words of guidance. In making a cake, you need the proper ingredients. If one or more of them are missing, it will not be a cake. In addition, the quality of the cake depends on the quality of the ingredients. In my lecture, the "cake" is the U.S. mining industry of the future. A national perspective President George W. Bush in his State of the Union Address (Bush, 2002) delivered on January 29, 2002, defined three national objectives: •win the war on terrorism, •protect the homeland and •revitalize the economy. Under the heading "revitalize the economy," he indicated the importance of "good jobs" and "energy production" by saying: "Good jobs begin with good schools. Good jobs also depend on reliable and affordable energy. This Congress must act to encourage conservation, promote technology, build infrastructure and it must act to increase energy production at home so America is less dependent on foreign oil." I wish that he would have broadened his focus and stated instead that: "This Congress must act to encourage conservation, promote technology, build infrastructure, and it must act to increase materials production at home so America is less dependent on foreign sources." With regard to jobs, all jobs are not equal. To paraphrase John Reeves of MidContinent Resources (Reeves, 2002): "If our nation is to prosper, we all cannot make a living by doing each other's wash. Some of us, at least, must be actively engaged in the primary production of raw materials from the riches of the earth and other Americans must turn those materials into consumer products." The unfortunate trend in our country has been to neglect the primary production of basic materials, even those coming next in line. We have left those responsibilities to others while we concentrate instead on performing various services, i.e., doing each other's wash and flipping burgers. This cannot continue. It must be remembered, especially by those in leadership positions, that all "jobs" are not created equal. Some jobs are much more essential to the security and wellbeing of our country than others. We must be sure that the important ones are in place. We cannot produce the basic materials that our nation requires without access to those materials. This leads to my Proposition 1: You cannot have a viable mining industry without a clearly enunciated, positive U.S. materials policy. Background regarding U.S. materials policy Resources for freedom. In January 1951, President Truman created the President's Materials Policy Commission, with William S. Paley as chairman. As expressed in the invitation letter from the president to Paley: This commission, within the executive office of the president, is to study the broader and longer-range aspects of the nation's materials problems as distinct from the immediate defense needs. The task of the commission is to make an objective inquiry into all major aspects of the problem of assuring an adequate supply of production materials for our long-range needs and to make recommendations that will assist me in formulating a comprehensive policy on such materials. The commission should study, together with any other aspects deemed by it to be pertinent, such questions relating to production materials as: - the long-range requirements outlook; - the long-range supply outlook; - the prospect and estimated extent of shortages; - the consistency and adequacy of existing government policies, plans and programs; and - the consistency and adequacy of private industry practices.

Jan 1, 2003

By Y. C. Kim

This paper describes the implementation aspect of a blast hole kriging system which has been developed for the purpose of daily ore-waste control in an open pit mine. The primary goal of blast hole kriging is to improve the ore-waste delineation procedure. A complete computer program package called Blast Hole Kriging (BHK) System was developed for IBM/PC AT or XT computer, using Fortran language and supplemented by a few Assembly language routines for bit-map manipulation. The emphasis of this paper is on the implementation aspect of the developed system. For this reason, the requirements for practical implementation and the system design considerations are discussed in the paper, as well as the main features of the University of Arizona's BHK System.

Jan 1, 1990

By R. Sellaro, E. Sarver

It has long been understood that extended occupational exposures to respirable mine dusts can lead to chronic lung disease. In underground coal mines, coal workers pneumoconiosis (CWP) and silicosis are major concerns. While many efforts have been made with the aim of understanding the mass-based concentrations and silica contents of respirable dusts under a variety of mining conditions, little research has been completed in characterizing dust at the individual particle level (by composition, size and shape). This study employed scanning electron microscopy with energy dispersive x-ray (SEM-EDX) to analyze dust samples collected from an underground coal mine in Central Appalachia. The results indicated that particle characteristics can vary widely between locations, though many trends might be explained based on knowledge of mining conditions. A continuous personal dust monitor (CPDM) was also used during the collection of some samples to determine respirable dust concentrations, which were compared against estimated concentrations based on the particle-level analysis.

Jan 1, 2014

By Carl Rampacek

Laboratory and small-scale continuous pilot-plant investigations made at the Tucson Metallurgy Research Laboratory of the Bureau of Mines have demonstrated that the copper segregation process is applicable to the treatment of oxidized and mixed oxide-sulfide copper ores regardless of the gangue constituents. The process comprises heating the ore to a temperature of 750° C. with small quantities- of sodim chloride and coke to produce metallic copper, which then is recovered by flotation. Tests were made on' 23 copper ores of different types containing 0.8 to 5 percent Cu, .The copper recoveries ranged from 73 to 96 percent in concentrates assaying 10 to 62 percent Cu, depending on the grade and type of ore, The direct operating cost for a 1,000-ton-per-day furnace and flotation plant is estimated at about- $3 per ton of ore.

Jan 1, 1960

By Magnus Ericsson

The unexpectedly quick recovery in world crude steel production in the second half of 2009 was due almost entirely to increased production in China that began in late 2008. Previous peaks in monthly production in China were matched by April 2009. The rest of the world had still not reached pre-crisis production rates by May 2010. Chinese production drives growth, but there has been some growth in most other larger crude steel producing countries as well, compared to production in 2009. If the production rate of the first four months of 2010 continues, the total output of crude steel in 2010 will be somewhere around 1,410 Mt (1.5 billion st), the same as in the record year of 2007.

Jan 1, 2010

By Elimame Elaloui, Kais Elghniji, Constantin Virlan, Aurel Pui, Chaima Ouled Amor

Separation and identification of minerals composing the Tunisian silica sands have been conducted by acid etching and hot filtration/sedimentation (HFS) without affecting the quartz component. It was found that the hot acid etching process is an effective method to separate quartz and clay minerals in the silica sand. The SEM micrographs of the silica sand show rough surface and some cracks with irregular shapes. The surface becomes clean and smooth after acid etching process. After chemical dissolution, the clay minerals were recovered by hot filtration following by sedimentation at low temperature. FT-IR, EDS maps, and secondary electron (SE) analyses of separated clay minerals reveal the presence of Fe2O3, montmorillonite, and kaolinite minerals. The LIBS analysis of clay minerals shows the presence of Al, Fe, Ca, Al, and Mg. The sequential etching process can be introduced in the purification methods as an effective way to separate quartz from clay minerals.

Jul 29, 2020

By Ali Ahmadi, Andreas Rausch, Angela Binder, Stefan von der Mark, Dhananjeyan Jeyaraj, Jana Thomas, Nils Nöther, Stefan Wittek, Thomas Ulrich, Eleni Gerolymatou, Mario Kolling, Helmut Mischo, Michael D. Martin, Tugba Sen, Jens-André Paffenholz, Erik Farys, Oliver Langefeld, Wilfried Ließmann

This paper outlines the MOVIE project, which is dedicated to the development of a digital twin for an underground laboratory at the research and education mine “Forschungs- und Lehrbergwerk Reiche Zeche” in Freiberg (Germany). Data from induced rock deformations and temperature fluctuations is collected using fiber-optic sensors. The objective of the project is to establish a virtual laboratory for real-time analysis of the interactions between geology, geomechanics, geometry and ventilation. This will be achieved by integrating models from these disciplines with artificial intelligence, creating a sophisticated hybrid model. The insights gained will enhance safety and efficiency in mining through improved digital planning options, ultimately contributing to more effective resource management and operational decision-making in different mining environments.

Feb 1, 2025

By Arash Dahi Taleghani, Pooyan Asadollahi

Slurry walls, also known as diaphragm walls, are commonly used as temporary and/ or permanent support of excavation for construction of shafts in soft ground. Through case history, this paper demonstrates economical benefits of disregarding long-term structural contribution of the slurry walls particularly in severe environmental condition. In addition, for temporary slurry wall shaft systems, possibility of using steel fiber, synthetic fiber or additives in lieu of temperature/shrinkage reinforcement is discussed with detailed analysis. Finally, the paper will be concluded by introducing unreinforced slurry wall shaft system using newly developed/patented concrete additive.

Jun 13, 2021

By I. Iwasaki

Differential flotation of bulk sulfide concentrates from Duluth gabbro into copper and nickel concentrates could be implemented by first destroying the hydrophobic coating with ozone and then by recovering the copper concentrate with a copper-selective collector. A number of parameters involved in the use of ozone; such as the sequence and the conditioning time of ozone treatment, the pulp pH, and the level of xanthate addition, were investigated.

Jan 1, 1985

By Robert E. Thurmond

With modern exploration techniques, it seems likely that an increasing number of the orebodies to be found in the future will be under alluvial fans or valley fill. As a result, a larger proportion of open pit mines will be confronted with the necessity for removal of substantial quantities of alluvial overburden; whereas in the past, for the most part, the open pit mine operator has dealt mainly with hard rock. If this proves to be the case, methods, equipment, and costs for alluvium stripping will become an increasingly important factor in open pit mine planning. Several operations are now faced with this situation, and various methods and equipment are used. At Pima Mining Company's operation the stripping ratio is in the range of 6/1 Well over half of the stripping volume is alluvium. The alluvium is removed almost entirely by carryalls hauling direct to a waste dump. Some removal has been accomplished by shovel and truck operation; more will be done by this means in the future. At American Smelting and Refining Company's neighboring .Mission Mine, nearly all alluvium removal is by large shovels and, trucks. U. S. Borax's Boron operation is accomplishing alluvium removal with carryalls but has been investigating other methods and equipment. The various operations in the Gas Hills Uranium District in Wyoming are stripping mainly with carryalls, although some small draglines are employed. The M. A. Hanna Company in the Mesabi Range employs large draglines and conveyor systems for removal of glacial fill. Nchanga Consolidated Copper Mines in Northern Rhodesia strips overburden with a large excavating wheel and conveyor system. There are no doubt other open pit operations with which the writer is not familiar, that are handling large quantities of alluvial overburden.

Jan 1, 1963

By G. Roy, C. B. Pettersson, S. Nandagiri, D. J. Ivor-Smith

The Coastal Water Authority's 2,740mm/2,590mm (108 in./102 in.) pipeline, known as the Northwest Lateral Project, will transport raw water from an existing pipeline over 14.3 km (8.9 miles) to the City of Houston's East Water Purification Plant. The new pipeline crosses under Houston Ship Channel and Greens Bayou in tunnels at approximately 30.5m (100 feet) and 25.9m (85 feet) depths, which present unique experiences in tunneling under open bodies of water in the Gulf Coast's soft ground conditions. An earth pressure balance TBM is being used for the deep tunnel sections where the ground demonstrates high overload factors and variable conditions ranging from clays to silty sands. This paper discusses the design approach for the tunnels and shafts, ground conditions, constructability, and selection of the primary lining system.

Jan 1, 1989

By C. RAMADINI, F. NURJAMAN, A. SHOFI, B. SUHARNO

In this work, the selective reduction of lateritic nickel ore was carried out using sodium sulfate, sodium carbonate, and sodium chloride as additives. The 5 wt% of anthracite coal, which contains 60.35% of fixed carbon and 1.9% of sulfur, was used as a reductant. All raw materials were mixed homogenously prior to the pelletization process into 10–15 mm of diameter. The reduction process was carried out to 50 g of pellets at 950 °C, 1050 °C, and 1150 °C for 60 min in a muffle furnace at atmospheric pressure. It continued with a wet magnetic separation process to separate ferronickel (concentrates) and impurities (tailings). Iron and nickel grade analysis was performed using XRF, while phase transformation and microstructure were analyzed with XRD and SEM–EDS. The results showed that the sodium sulfate was superior, resulting in the highest nickel grade in concentrate, i.e., 15.06%. The sulfidation mechanism, which could inhibit the metallization of iron, effectively increased the nickel grade in concentrate than decomposition of carbonate and chloridization process. The sulfur content in the reductant also influenced the selective reduction process. It promotes more sulfidation of iron, thus increasing the nickel grade in concentrate.

Jul 7, 2021

By Peter G. Chamberlain

Domestic mining will not produce a significant portion of the manganese consumed in the United States unless new mining and processing techniques are implemented that will enable domestic lean ores to economically compete with rich foreign ores. One mining-processing technique that appears promising for certain deposits is in situ and/or heap leaching with aqueous SO2. Since leaching offers economic advantages of low capital costs, low operating costs, and short start-up times as well as environmental and safety improvements over conventional mining-processing, the Bureau of Mines studied the leachability of manganese deposits from several districts. Manganese oxides, hydroxides, and carbonates were leached to 80 to 90 pct recovery in 7 to 40 days of leaching with a solution containing 5 pct SO2 in column leaching tests. Preliminary cost analyses of surface mining-heap leaching, block caving-in situ leaching, and shrinkage stoping-in situ leaching indicate that the products of manganese leaching may be economically produced for the chemical and electrolytic manganese industries. The easiest marketable product to obtain would be a manganese sulfate commonly used as a fertilizer amendment. Manganese carbonates and hydroxides could also be precipitated from the pregnant leach solutions.

Jan 1, 1983

By Stacey Leichliter

The Cripple Creek and Victor (CC&V) Gold Mine (Cresson Project) (Fig. 1) is undergoing an expansion to extend production to the year 2025. This expansion involves building a high-grade ore mill, another valley leach facility (VLF) for heap leach operations and expanding the overburden storage areas. The current operating pits are progressing downward from the oxide ore into a more sulfide and telluride-rich orebody. There is still oxide ore present in the current pits and planned pits not yet mined. There is an increased need for two recovery processes for these two different types of ore. The key component to this expansion is the high-grade ore mill, which has gravity, flotation and carbon-in-pulp (CIP) circuits. The mill will be the main recovery process for the higher grade, more sulfide/telluride-rich ore. This ore type does not recover well on the heap leach pad due to its refractory nature. Geometallurgy is vital for ore characterization for the two recovery methods. Geometallurgy helps develop indices that are used to predict parameters that influence overall recovery and production, such as hardness, crushability, grindability, pH fluctuations, gravity (coarse) gold, flotability and cyanidability. Using geology and mineralogy along with other analytical data, geometallurgical models are constructed and applied to the resource block model for proper planning and extraction of the gold. Geometallurgy aims to analyze the variability in the different responses to the parameters to help reduce risk (costs) and optimize recovery (profit).

Jan 1, 2013

By A. Noble

"A supply of sustainably sourced rare earth elements (REEs) is critical for several high-tech industries, renewable energy technologies, and defense applications. Recent studies have shown that REEs exist in coal and coal combustion byproducts at elevated concentrations and in quantities that could meet domestic demand. Despite these promising findings, declines in rare earth prices, volatile commodity markets, and challenging geo-metallurgical conditions have jeopardized this potentially valuable REE resource. While the dilute REE concentrations inherently necessitate low-cost separation technologies, the ultimately operating cost threshold for economic extraction must be based on commodity price projections and market demand. In this paper, the micro-pricing principle is used to develop a rigorous economic model assessing the inherent value of REEs in coal materials. This model is based upon basket pricing of individual elemental oxides, and elemental distributions of coal samples from various basins. These results may be used to assess the economic viability of potential REE concentration and refining technologies INTRODUCTION Recent efforts by US Department of Energy (DOE) and the National Energy Technology Laboratory (NETL) have suggested that rare earth elements (REEs) may exist in coal and coal byproducts at concentrations suitable for economic extraction and processing. While the knowledge of REE occurrence in coal material dates back over 50 years, recent supply restrictions and material criticality considerations have prompted a national interest to establish a sustainable domestic supply of REEs. REEs are not “rare” in the sense of crustal abundance; however, few natural processes lead to concentrated ore deposits. As a result, the elevated concentrations found in coal material may provide a potentially promising resource for these materials. While the term “rare earths” is often used to describe a singular concept, the 15 rare earth elements actually have varying and sometimes contrasting scarcity and cost profiles. Various authors have proposed classification systems to provide information on REE criticality (e.g. Seredin and Dai, 2012, Zhang et al., 2015). The most straightforward classification is provided on the basis of geochemistry with designations for “light”, “medium” and “heavy” rare earths. Light rare earths (those to the left of the periodic table: Ce, Pr, Nd, and Sm) tend to be more common and less valuable when compared to their medium (Eu, Gd, Tb, Dy, and Y) and heavy (Ho, Er, Tm, Yb, and Lu) counterparts. While light rare earths are often found in traditional ore deposits at economic concentrations, the heavier rare earths are almost exclusively found as ion-absorbed clays (Seredin and Dai, 2012)."

Jan 1, 2016

By J. Sanko

When faced with the task of designing a process control system the control engineer must consider the following: 1. The type of process to be controlled and the manner in which the process must be controlled (the algorithm). 2. The type of equipment to be used to implement the control system. 3. A means of describing the control system for use in the following areas: a. Project engineering. b. Procurement of the control system equipment. c. Plant startup. d. Operator training and reference.

Jan 1, 1981

By F. Segobia, H. Lozano, M. Portal, F. Ysla, L. Goicochea

This case study evaluates the long- term physical stability of various historical mining structures remediated by the Center for Mining Environmental Research and Studies (CIEMAN) in Hualgayoc, Cajamarca, Peru. The region has a long history of mining activity, with remnants dating back to pre-Inca times. CIEMAN has assumed responsibility for remediating 286 environmental liabilities in the area, including adits, shafts, pits, tailings, and waste rock dumps. The study analyzes the methods employed to stabilize these structures, including geotechnical engineering techniques and revegetation. Long-term monitoring results are presented, assessing the effectiveness of remediation measures and predicting the future stability of the structures. This study highlights the importance of responsible remediation of mining environmental liabilities to ensure the safety and sustainability of communities and ecosystems affected by historical mining.

Feb 1, 2025