Search Documents

By Xuezhong Wang, Hao Guo, Tao Tu, Qingsheng Liu

The scheelite concentrate was leached with a mixture of sulfuric and oxalic acids. Chemical compositions, mineral phases, and morphology were characterized by XRF, XRD, and SEM–EDS. Based on the results of the single-factor experiments, the response surface methodology (RSM) was chosen to optimize the leaching parameters: temperature, time, and concentrations of sulfuric and oxalic acids. The RSM results indicate that the optimum values for those parameters are as follows: temperature 72 ℃, sulfuric acid concentration 1.48 mol/L, oxalic acid concentration 0.96 mol/L, and reaction time 2 h. Under the optimal leaching conditions, the model predicts a maximum leaching yield of 99.5%, compared to the value of 99.1% obtained experimentally, that is, a discrepancy of only 0.04%. This good correlation shows that the quadratic polynomial equation obtained by the RSM optimization is reliable. The importance on leaching parameters of scheelite is, in decreasing order, temperature, time, sulfuric acid concentration, and oxalic acid concentration.

Oct 11, 2021

By Shenghui Chu, Zhibiao Guo, Dongshan Yang, Yuanxin Zhao, Xiaohui Kuai, Jingwei Gao

The technology of automatically formed roadway without pillars (AFRP) via roof cutting and pressure releasing (RCPR) is a reformatory method for gob-side entry retaining, which automatically creates a roadway by utilizing the fragmenting and expanding properties of rock strata and the mining pressure, to realize a novel technique for coal mining without coal pillars. The Anju Coal Mine is the first kilometer-deep mine where this technology is applied. To conduct a geomechanical model experiment, this research uses the 5307 working face in this mine as its backdrop. The experimental results show that this technology can efficiently decrease the pressure of the AFRP surrounding rock. The roof maximum stress of the AFRP is 21% lower than that of the belt roadway, while the side abutment pressure of the former is 13.4% lower than that of the latter. The comparison of model experiment data and field monitoring data shows that the roof and floor approaching deformations on the roof-cutting side and solid coal side of AFRP differ by 8.8% and 9.6%, respectively. The model experiment results and field monitoring data show good agreement, and the deformation of the AFRP surrounding rock can be successfully managed by this technique. The study’s findings can serve as a guide for using this technology in kilometer-deep coal mines.

Jul 31, 2023

By Shuchen Sun, Ganfeng Tu, Chuan Liu, Xiaoping Zhu

The hydrometallurgical residue generated during the hydrometallurgical processing of waste automotive catalysts is valuable as a secondary resource. In this study, a process of platinum recovery from the hydrometallurgical residue by high-temperature smelting process was proposed. Results of lab- and pilot-scale experiments show a high recovery of more than 98% of platinum and glass slag was successfully obtained by controlling the Fe3O4 addition, C/Fe3O4 mass ratio, CaO/SiO2 mass ratio, smelting temperature, and holding time at 15 wt%, 0.4, 0.6, 1500 °C, and 120 or 60 min, respectively. Results from the pilot-scale show that the platinum contents in the glass slag and alloys were less than 4 g/t and more than 0.6 wt%, respectively. Therefore, the process proposed in this study is a prospective and effective approach for reutilization of hydrometallurgical residue containing platinum.

Oct 12, 2020

By Henry J. Schwellenbach

The New York Trap Rock Corporation has four plants located along the Hudson River, all within 70 miles of New York City. The company produces crushed stone for use as construction aggregate, with a total annual production amounting to 6 million tons. The crushed stone is moved to markets in metropolitan New York, New Jersey and Long island areas by water transportation. There are daily deliveries of approximately 35 scowloads to the market area. Its customers are contractors with ready-mixed concrete and asphalt plants located on the water, where the aggregate is unloaded for its ultimate use. For a number of years capital equipment was replaced only when the current operating machinery was no longer serviceable, or when' a need was apparent for a different type of equipment. There was no particular regard for efficiency or for operating and maintenance costs. Such lack of system often resulted in the emergency purchase of equipment which was later found to be unsuitable for the job. A few years ago it became apparent that a systematic procedure was necessary. After evaluation of several systems, an individualized plan was evolved from the basic pattern developed by the Machinery and Allied Products Institute. The system adopted by New York Trap Rock has proved wholly satisfactory.

Jan 1, 1959

By Juan J. Monsalve, AMAN SONI, ALEX PFREUNDSCHUH, Nino Ripepi

Ground control failures are one of the main causes of accidents in the underground stone mining industry. Some of the fundamental tools for rockfall hazard identification are related to rock mass characterization and geotechnical discontinuity mapping. Recent technological advances in these methods are related to remote sensing techniques and point cloud processing software for automated discontinuity mapping. Remote sensing techniques, such as LiDAR and photogrammetry, generate multimillion point clouds with millimetric precision, capturing the structure of the rock mass. The automated point cloud processing tools offer alternative algorithm-based methods to characterize and map these discontinuities. However, their applicability is constrained by multiple factors such as site specific conditions of the rock mass and the parameters used within the mapping algorithms. This paper evaluates the performance of automated discontinuity extraction software compared with manual virtual discontinuity mapping. Sampling windows from laser-scanned sections in an underground limestone mine are defined and mapped using discontinuity set extractor (DSE). Results from the virtual discontinuity software are compared with manually extracted fractures from I-Site based on reviewing orientation, trace length, spacing, number of extracted discontinuities, and processing time. The analysis determined that the automated mapping algorithm was able to identify the same discontinuity sets that had been manually mapped. The automated mapping software mapped an excessive amount of smaller fractures, which caused the comparison of both mapping techniques to be unsuccessful in terms of trace length and spacing.

Mar 19, 2021

By Staff

"In 2014, the estimated value of total mine production of nonfuel minerals in the United States increased. The quantity of production increased for most mineral commodities mined in the United States, as did prices. Notable exceptions were the declines in prices for most precious metals. Minerals remained fundamental to the U.S. economy, contributing to the real gross domestic product (GDP) at several levels, including mining, processing and manufacturing finished products. Following the reduction in construction activity associated with the 2008- 2009 recession that continued through 2011, the construction industry continued to expand in 2014, with increased production and consumption of cement, construction sand and gravel, crushed stone and gypsum, mineral commodities that are used almost exclusively in construction. Other segments of the nonfuel minerals industries increased as well. Trends in other sectors of the domestic economy were similar to those for industrial mineral production (Table 1).Discussion of mine production is frequently segmented according to the type of materials produced within the broad categories of metals and industrial minerals. Industrial minerals can be further subdivided as construction aggregates and other industrial minerals. The materials with the highest unit values, usually metals, tend to have very low production rates compared with those of many low-valued materials, such as crushed stone or construction sand and gravel. Therefore, for discussion and analysis of the performance of the minerals industry in general, the value of production is used rather than tonnage produced. Although the value of metals and industrial minerals mined in the United States are similar, if tonnages are compared, construction aggregates dominate, dwarfing the production of all other minerals combined.Mineral industry performanceThe estimated value of nonfuel mineral raw materials, including metals and industrial minerals, produced at mines in the United States in 2014 was $77.6 billion, a 3.5-percent increase from $75 billion in 2013 (Table 2). Net exports of mineral raw materials and old scrap were $15 billion (Fig. 2). Domestic raw materials, along with domestically recycled materials, were used to process mineral materials worth $697 billion. These mineral materials, including aluminum, brick, copper, fertilizers and steel, and net imports of processed materials (worth about $41 billion) were, in turn, consumed by downstream industries with a value added estimated to be $2,530 billion in 2014.In the United States in 2014, mine production of each of 14 mineral commodities was worth more than $1 billion. These were, in decreasing order of value, crushed stone, copper, gold, cement, construction sand and gravel, iron ore (shipped), industrial sand and gravel, molybdenum concentrates, phosphate rock, lime, salt, zinc, soda ash and clays (all types)."

Jan 1, 2014

By Paul M. Jr. Musgrove, Thomas D. Henderson, Mark B. Nesbitt

Introduction History. Vat leaching operations began in October 1953. Since that time, about 4.2 million tpy of oxide ore averaging 0.72% copper have been treated. Economic conditions, improved operating methods, and increased production facilities have allowed the ore grade to be reduced over the years. The average ore grade was 0.84% Cu during the 1950s, 0.68% in the 1960s, and was 0.50%, or below, during the 1970s. By 1961 some 35 million tons of oxide ore had been removed from the mine, exposing the underlying sulfide ore body. A 5,000¬ tpd concentrator was constructed and put into operation to treat the sulfide ore in November 1961.1 The original crushing plants were used for both oxide and sulfide ores, but by adding a third crushing shift, six days per week, the total ore treated was raised from 12,000¬17,000 tpd. Dwindling oxide ore reserves prompted expansion of the concen¬trator to 13,500 tpd in 19672 so that exhaustion of known reserves of both ores would occur at nearly the same time. Again, no additional crushing facilities were added during the expansion. It was anticipated that the treatment rate of oxide ore would be reduced from 12,000 to about 9,000 tpd. Instead, the addition of two crushing shifts per week and improved operating procedures have increased the treatment rate to 26,500 tpd-13,000 tpd to the leaching plant and 13,500 tpd of sulfide ore treated in the concentrator. Geology. The Yerington ore body is a disseminated porphyry copper deposit where a quartz monzonite porphyry intrusive contains the major part of the ore values, with some copper mineralization found in the adjacent granodiorite and other rocks. The geology of the Yerington Mine was aptly described by J. R. Wilson (Mining Congress Journal, June 1963). The ore body is one of few porphyries where geologic conditions were optimum for the formation of an important concentration of oxidized ore with minimum economic effect of secondary enrichment. The principal mineral in the oxidized zone is chrysocolla, which irreg¬ularly occurs dispersed throughout the rock and as narrow seams along fissures. The grade of the ore in the oxidized zone is generally the same as in the primary sulfide below, although some massive concentrations do occur as vein-like fissures and as filling of breccia zones. Cuprite, tenorite, melaconite, malachite, and azurite occur but are not abundant. Lying between the chrysocolla horizon and the primary sulfide is a transition zone whose limits are irregular but seldom with vertical range exceeding 50 ft. Chalcocite, cuprite, melaconite, native copper, and chrysocolla occur superimposed on the primary sulfides. Chalcocite replacement of chalcopyrite, as well as secondary chalcocite, do occur. The primary sulfide minerals are chalcopyrite and pyrite, with minor amounts of bornite and covellite. There are no appreciable gold or silver values, and molybdenite has rarely been noted.

Jan 1, 1985

By L. Xia, B. Hart, V. Sidorkiewicz

Sodium silicate(s), also known as “water glass”, are one of the oldest and most widely used industrial chemicals. Its first use in North American mining operations can be traced back to around 1925, which coincided with early use of xanthates in mineral flotation. Silicate functions as a sulphide and non-sulphide gangue mineral dispersant, depressant and modifying reagent in grinding and flotation operations. It is believed that soluble sodium silicate promotes selectivity of value added sulphides against gangue minerals, resulting in both grade and recovery improvement. This paper seeks to link improved grade/recovery to the interaction characteristics of minerals and the sodium silicate. A systematic study was performed with individual mineral species, an artificially designed model ore and the feed ore from a copper metallurgical operation. The function of sodium silicate was evaluated in the context of colloidal chemistry and linked to mineral surface chemistry. Measurement of pulp rheology and mineral zeta potential identified that sodium silicate works as a dispersant. The dispersion is accomplished by increasing a mineral’s net surface charge, resulting in a mineral variable change in viscosity. Bench scale laboratory flotation tests suggest that better dispersion leads to a diminished interaction of chalcopyrite with gangue. The improved Cu grade and recovery then are likely in response to an increased accessibility to collector along with a linked increase in particle bubble attachment resulting in better separation efficiency. ToF-SIMS surface chemical analysis of the flotation samples found a higher proportion of sodium silicate on minerals from the flotation tailings relative to the concentrates. Moreover, attachment of sodium silicate appears to be mineral specific; the data indicates that sodium silicate favours the surface of gangue phases over the value sulphides. INTRODUCTION Mineral processing involves enrichment of valuable minerals from an ore, where the separation process utilizes differences between the properties of the value-added and gangue minerals. The properties of minerals, for example composition, specific gravity, particle size, magnetic properties etc., in any flotation feed ore, can vary significantly between the various minerals present. In flotation seperation surface chemistry and wettability is a significant component promoting selective separation of the various mineral phases [1,2] Mineral surface wettability can be changed, advantageously or deleteriously, by many factors including: surface layer alteration through oxidation; galvanic interactions; attachment of secondary precipitates; the adsorption of various reagents [3] In the flotation context the wettability of a minerals surface can be manipulated by various reagents. Collector reagents may selectively attach to specific minerals in the mineral/water slurry enhancing their surface hydrophobicity, increasing bubble-attachment efficiency and improve flotation kinetics and mineral recovery [4]. In contrast, depressant reagents may selectively reduce a minerals surface hydrophobicity resulting in poor particle-bubble attachment and non flotation. In essence, a mineral flotation flow sheet is designed to induce/promote a hydrophobic surface to the value mineral and a hydrophilic surface to all others. Therefore, the versatility of the froth flotation process lies in the selection of different flotation reagents.

Jan 1, 2019

By David B. McWhorter

Conventional analyses of seepage through saturated media do not apply when tailings impoundments are located above a partially saturated zone. Three stages of seepage are identified and methods for estimating the seepage rates and duration of each stage, based upon flow in partially saturated and saturated porous media, are demonstrated. The effectiveness of earthen liners is discussed and procedures for estimating the required properties of the porous media are provided.

Jan 1, 1978

By Robert E. Kirby

The potash mine and refinery of AMAX Chemical Corporation is located 26 miles east of Carlsbad on the north end of the potash producing areas. This property was developed between 1949-1952 and production of muriate began in August 1952. Two shafts, located 400 feet apart, were sunk to the ore zone 900 feet below the surface. A 15-foot diameter ore hoisting shaft equipped with a 1000-ton ore pocket, crusher and automatic skip loading equipment plus a 20-foot diameter service shaft with a curtain wall for exhausting air were provided. Sylvinite production to date has been from the first ore zone, stratigraphically, the lowest of ten identified mineralized zones in the salt section. This first ore zone has been the top producer of Muriate of Potash over the years. In our area we do have some very marginal mineralization in the third ore zone some 35 feet above the first. We have not mined from this seam as yet but we are investigating the economics very closely with access slopes and an experimental mining panel. Our ore seam is generally flat lying but does have local gentle rolling with grades from 2% to 5%. The mine was designed and developed from the beginning with conventional mining practices and rail haulage from the mining section to the ore pocket. As mining progressed in the early years, production increased from less than one million tons annually to a maximum of 3,935,000 tons in 1964. Efficiency also kept pace with the increasing production and continually improved until the efficiency of the production crews reached an average of 100.3 tons per manshift in 1964.

Jan 1, 1974

By T. C. Vogt

The past history of uranium production has been dominated by strip and shaft mining methods, but recently in-situ leaching has emerged as a viable alternative for uranium recovery. (1-8) Mobil was the first company to start in-situ uranium leaching in New Mexico. Mobil's Crownpoint project areas are in Mdinley County and are part of the Grants Mineral Belt. The major uranium deposits in this area occur in the Westwater Canyon Member of the Jurassic Morrison Formation. (9-11) The ore depth at the Crownpoint project is about 2000 ft. In an earlier paper we discussed the uranium mineralogy of an areally broad sampling of Crown- point ore. (12) The organic carbonaceous material often associated with the coffinite ore was characterized in some detail. The organic material appeared to be a very mature, coaly-type kerogen derived from plant components. This result was consistent with other studies on such carbonaceous material. (13-15)

Jan 1, 1981

By Wenjun Ju, Xiaodong Sun, Jianwei Zheng, Bingding Yi, Zhaorui Ma, Pengfei Jiang, Lingfu Zhu, Yangfa Zheng

The presence of hard roof poses a significant threat to the safety of underground coal mining. In this study, a mechanical model is established for underground stopes to analyze the overburden structure with the advancing of the mining face. It is indicated that the load-bearing arch structure (LBAS) is formed above the stope for roofs with regular hardness, whereas the reversed-basin bearing structure (RBBS) is formed for hard roofs. Compared with the LBAS, the RBBS can induce an additional pressure at the foot of the bearing structure, and this effect becomes less as the distance between the hard roof and stope increases. The ultra-deep borehole hydro-fracturing technique (UHT) is proposed to weaken the hard roof for pressure release, and the associated equipment and procedures are also presented. The UHT is based on horizontal drilling along the axial direction of the roadway in the roof, and then the receding segmented hydraulic fracturing technique is used to achieve the purpose of fracturing (weakening) of the surrounding rocks. Field tests are carried out in 3022 roadway of Daliangwan coal mine in Yulin to assess the developed technique, equipment, and fracturing procedures. To evaluate the fracturing effect, deep borehole stress-meters are installed at different depths of the fractured and un-fractured zones of the roadway, along with hydraulic support pressure sensors placed at the mining face. The results show that compared with the un-fractured zone, the pressure on the wall and pillar sides is lower than that in the fractured zone, and the associated weighting duration and weighting area ratio of the fractured are reduced by 53.23% and 33.59%, respectively. This indicates that the presented UHT can provide a new solution for the prevention and control of mining disasters induced by hard roof failures in underground coal mining.

Nov 2, 2020

By JESSICA W. A. AZURE, Kansake A. Bruno, Samuel Frimpong, AZUPURI G. A. KABA, FORSYTH A. KADINGDI, PROSPER E. A. AYAWAH

Blasting generates undesirable ground vibration with adverse effects on humans, the environment, and structures. Numerous studies have used various techniques including machine learning (ML) to predict the peak particle velocity (PPV) caused by blasting in surface mines. These studies used the validation-set approach to evaluate the performance of their predictive models. In this study, Random Forest (RF), Gaussian Process (GP), and Gradient Boosting Machine (GBM) were applied for the prediction of PPV using data from a large open-pit gold mine in Ghana. An ensemble model based on a stacked generalization approach was then built on these three base models to significantly improve the PPV prediction performance. The model evaluation was done using repeated tenfold cross-validation which resolves the challenges with the validationset approach for small datasets. The dataset used in this study comprised a total of 196 measurements taken from different blasting operations. R-squared ( R2 ), mean absolute error (MAE), and root mean square error (RMSE) were used to evaluate the model performance. The results obtained from these models revealed that all the base models did not significantly outperform each other. However, the stacked generalization approach had a better performance, with RMSE = 0.12, R2 = 0.96, and MAE = 0.07. This approach presented an improvement over the existing methods and will be useful for highly accurate predictions of ground vibration during blast design. The application of this model will be useful for efficient and effective blast design.

Nov 8, 2022

Computer programs commonly used to simulate mining operations generally require a fair amount of data. The common data input methods have been by either creating an ASCII data file or answering numerous questions during the data input phase. Both methods of data entry are tedious, time consuming, and inflexible. A screen handling system has been developed to drive FORTRAN-77 application software for the MS-DOS environment. The system utilizes keyboard functions with an aid of extended ANSI codes. It also allows a multi-view input data entries.

Jan 1, 1990

By J. A. M. Cano

Pot Grate tests were carried out in the pilot plant at Samarco producing pellets containing SiO2 between 2.0% and 2.2% in a wide range of basicity to be used in blast furnace. These pellets were submitted to tests in Samarco's laboratory and another laboratory in Germany to evaluate the metallurgical properties. The pellets in the binary basicity range (CaO/SiO2) from 0,87 to 0,95 were those that presented the best results in the Pot Grate tests. Based on the results, these pellets are being routinely produced?on industrial-scale confirming the results observed in laboratory tests.?

Jan 1, 1994

By Jaeheon Lee, Jai‑Won Byeon, Junmo Ahn, Jun‑Jae Lee, Eun‑Woo Kim, Yoo‑Jin Kim, Jiajia Wu, Jae‑Yeon Kim

Growing demand for valuable battery materials and environmental issues from battery disposal make the recycling of spent lithium-ion batteries (LIBs) essential. Specifically, the green approaches using organic reagents have garnered many attentions for battery recycling. In this study, a synergetic organic leaching system using methanesulfonic acid (MSA) of strong organic acid and citric acid (CA) with good chelating ability was investigated to extract valuable metals from LiCoO2. Hydrogen peroxide was used as a reducing agent to enhance leaching kinetics. Cobalt extraction of 98% and lithium extraction of 97 % were achieved in the optimized condition; 2.4M MSA, 1.6M CA, 1.0 vol% H2O2, S/L ratio 80 g/L, 85 °C, and 1 h. The optimal leaching condition of the MSA-CA mixed leaching system exhibited good applicability to various cathode scraps, such as LiCoO2, LiNixMnyCo1- x-yO2, and LiNixCoyO2. The dissolved Co and Li ions in the MSA-CA leachate were selectively recovered with high recovery efficiencies of 99 % and 97 % as Co3O4 and Li3PO4, respectively. The recovered Co3O4 and Li3PO4 were utilized to regenerate cathode materials. LiCoO2 and LiFePO4 were also synthesized through a solid-state reaction and hydrothermal method. The recycling process based on the MSA-CA-H2O2 synergetic leaching system was proposed, and it might be applied as a green and economical organic leaching system for the recycling of various types of spent LIBs.

Sep 20, 2023

By David W. Wisecarver

Kennecott Copper Corporation and the U. S. Bureau of Mines cooperated in a full-scale slope stability research project at the Kimbley Pit near Ely, Nevada. The west wall of the Kimbley Pit was mined from an over-all slope angle of 45° to an over-all slope angle of 57° and the pit was deepened nearly 50 feet. Mining was begun February 10, 1966, and completed October 30, 1966. Approximately 2.55 million tons of ore and waste were mined. The project was designed and carried out to learn more about the behavior of a pit wall as its slope angle is steepened and to obtain a possible insight into engineering parameters for use in design of future slopes. Data from this project are presented as obtained from (1) instruments installed in two adits for deformation and displacement measurements, (2) a subsidence network installed on the surface above the steepened wall, (3) pre- and post-mining observations of stress in rock, (4) sonic-velocity measurements, and (5) seismic and microseismic investigations. Changes occurred in measured quantities as the slope was steepened but stopped when mining was completed. Agreement was noted between the measured changes and predicted changes obtained from calculations using the finite element technique. Subsidence surveys and microseismic studies show the steepened pit wall to be stable.

Jan 1, 1968

By J. P. H. Steele, T. Vincent, C. Debrunner, M. Whitehorn

For a variety of reasons, the need for automation of underground mining equipment is growing dramatically, e.g., improved safety and health, availability of labor, deeper mines, and desire for more focused excavation. While there has been tremendous progress made in this direction, much needs to be done to reach the holy grail of an autonomous mining machine. This paper reviews a number of technological developments and presents research and development needs for future development. A report on our current project for the Western Mining Resource Center at CSM is included.

Jan 1, 2000

By D. A. Peacock

"INTRODUCTION Outer space technology and exploration have reached a tipping point so that mining and mineral processing in outer space is now a certainty and not a dream. Several competing companies, worldwide, are well on the way to building spaceships to land on the Moon and eventually mine the Moon and asteroids for volatiles, rare earth metals and Helium-3. The Google Lunar XPrize offers a $30 million prize1. China has recently landed a spacecraft on the Moon. The European Space Agency, with cooperation from the United States, has landed a spacecraft, Philae, on a comet. And, Mars One is planning a one-way trip to establish a settlement of humans on Mars. How and why are the Moon and asteroids and their resources of interest to private space industry and companies? Why are the Moon and asteroids viewed as a potential business venue? GEOLOGY OF THE MOON AND ASTEROIDS –WHY DO WE WANT TO MINE THERE? Space enterprises are actively working towards establishing and operating lunar and asteroid mining locations for resource extraction, resource processing, conversion to salable products, and distribution of the products and services in space and to Earth and beyond2. Forty-five years ago, the Apollo manned missions to the Moon returned rocks and regolith to Earth, which were studied and analyzed. What they found was that the Moon contains valuable minerals and resources. These minerals are largely due to meteor and asteroid impacts, which have, over eons, created this mineral rich regolith. These impacts have occurred on Earth as well, for billions of years, particularly early on in the history of the solar system. However, on Earth, wind, water, and vegetation have erased most of these impacts. On the Moon, in contrast, the only weathering is caused by subsequent impacts and the solar wind. The Moon regolith contains valuable rare earth minerals, platinum-group minerals (particularly where the Moon has been impacted by asteroids), volatiles (useful for processing and habitation), Helium-3 and titanium. Almost non-existent on earth, Helium-3 is abundant and accessible on the Moon and can be used in nuclear fusion power plants, producing much more energy than fission reactions and with much less radioactive waste. One of the main reasons Helium-3 is sought after as a fusion fuel is because there are no neutrons generated as a reaction product. Governments and private companies focus on mining of Helium-3 on the Moon as a basis for their economic models. Moon Express, one of the private companies who is planning on mining on the Moon, will recover moon rocks to fund its early operations25. Subsequently, it will recover Helium-3, platinum, and rare earth metals, as it engages in surface mining operations."

Jan 1, 2016

By Jonathan K. Hrica, CASSANDRA L. HOEBBEL, Jennica L. Bellanca

Accidents involving powered haulage and mobile equipment such as haul trucks often account for the greatest number of fatalities in the mining industry each year. Despite previous analyses that have identified root causes and other contributing factors, there is still a need to better understand the events leading up to these types of accidents, what lessons may be learned, and what strategies can be employed to prevent fatal accidents from occurring. This study examines Naturalistic Decision Making (NDM) using the critical decision method (CDM). The CDM is a retrospective interview approach used to explore timelimited, high-stakes, decision-making. In this study the CDM is used to obtain more information about what happens prior to, during, and after a potentially fatal situation such as a near-miss event, loss of control, or minor accident involving equipment damage. Researchers captured firsthand accounts from 21 haul truck operators involved in near-miss events from mine sites of various sizes and commodities throughout the United States. These accounts provide rich and detailed narratives from the perspective of haul truck operators themselves and reveal insights into what decisions haul truck operators make, what sensory cues they perceive, and what strategies they employ during challenging and non-routine situations. Decision-related themes that emerged from the data are presented and discussed. These results, along with potential solutions offered by study participants, can help to inform future research, raise awareness about hidden hazards, and build more creative interventions and realistic training scenarios for use by the industry to address haul truck safety issues.

Feb 1, 2024