Search Documents

By Michael E. Karmis

New and developing communication systems en-able underground miners to, not only connect to the surface from an increased communication coverage area, but also to be discovered in the event of an emergency. Communication and tracking systems are required by the U.S. Mine Safety and Health Ad-ministration (MSHA) regulations, aiming to enhance health and safety and routine production in underground operations. Modeling a mine?s potential communication coverage area will increase overall coverage and efficiency of the communication network itself. Modeling the propagation of wireless communications enables ideal broadcast locations to be found when designing a communications network. Strategic placement of broad-cast devices results in a reliable communication network that can better withstand disruption in daily operation and during a time of emergencies. Research on wireless communication in mines has been ongoing since 1922, when the U.S. Bureau of Mines performed experiments in its experimental mine in Bruceton, PA (Schiffbauer & Brune, 2006a). Ac cording to Dobroski and Stolarczyk (1982), ?as early as 1922, Bureau of Mines experiments showed that radio propagation in mines was possible but not practical.? In 2006, the underground communication technologies available to the mining industry had inherent problems that limited communication capabilities. Because harsh underground mine environments significantly reduce line of sight and propagation range and introduce power and safety concerns, the overall effectiveness of underground communication technologies were limited. After several coal mining accidents in early 2006, the U.S. Congress responded with the Mine Improvement and New Emergency Response (MINER) Act, enacted

Jun 1, 2010

By J. MacFadyen

The U.S. cement industry, including Puerto Rico, again set a record in terms of production and shipments. The increase in shipments came primarily from imports of portland cement as domestic production from produced and imported clinker gained only 1.9 Mt (2.1 million st). Clinker production as reported to the U.S. Geological Survey (USGS) was 88.6 Mt (97.6 million st), an increase of 1 percent. Gray and white portland cement production from domestic and imported clinker, estimated at 93.5 Mt (103 million st), was up 1.9 Mt (2.1 million st). Masonry cement shipments of 5.5 Mt (6 million st), which equates closely to production, was up 6.3 percent. Blended ce-ment shipments were up 35.9 percent from 2004 at 2.35 Mt (2.6 million st).

Jan 1, 2006

By Ashley Woodward, S. Katharine Hammond, Mayela Padilla-Salas

This paper presents a scalable framework for worker safety assessments. The paper focuses on uranium mine reclamation in underserved communities, specifically Cove Chapter of the Navajo Nation. By integrating field observations, OSHA data analysis, systems mapping, and a hierarchical occupational health pyramid, this framework identifies site-specific hazards while addressing broader socio-cultural dynamics. The approach improves upon existing safety programs by suggesting actionable, locally sensitive solutions that prioritize higher-order controls such as hazard engineering interventions and administrative controls. This study contributes to enhanced worker safety, efficient environmental restoration, and engagement in marginalized communities with abandoned mine lands.

Feb 22, 2026

By James Corcoran, Richard McLane, Joseph DeMello, Eric Carlson, Hans van de Vrugt

The Los Angeles County Transportation Authority’s Purple Line Extension Phase 1 is a $3.12 billion (USD) design-build, underground heavy rail project, connecting an existing station at Wilshire Boulevard and Western Avenue and extending west 3.92 miles under Wilshire Boulevard and terminating approximately 550 feet west of Wilshire/La Cienega Station. The project alignment runs through the heart of the world famous La Brea Tar Pits and one of the world’s largest urban oil elds. This paper presents a case history of the planning, design, and construction efforts to achieve successful construction of the bored tunnels through Reach 3 of the alignment. Further, this paper outlines the proactive partnership between the owner, Los Angeles County Metro (Metro), the Design Builder, Skanska-Traylor-Shea oint enture (STS), and Southwest Geophysics who provided the geophysical services. Specically, the project included background review of historic site data (e.g., oil eld maps, building foundation plans, historic aerial photographs, etc.), geophysical demonstration testing to ascertain the capability of borehole magnetics to detect oil wells, directional drilling of thousands of feet of horizontal and vertical boreholes, collection of high resolution magnetic gradiometer data along vertically and horizontally cased boreholes as well as the collection of surface magnetometer data, discovery (“ground truthing”) of detected geophysical anomalies, and abatement of potential obstructions within the tunnel alignment.

Jun 23, 2024

By J. Kern, T. F. Torries

Identifying high value areas of unmined coal when large quantities of coal are available relative to annual markets is difficult because of the uncertainty of when the coal is to be mined. A GIS based methodology developed to value reserve coal in a producing coal region for the purpose of ad valorem taxation also identifies high value areas for mining investment. The methodology is unique in that it accounts for most mining, environmental, and market factors to determine when specific properties are to be mined. The methodology and data base are useful for directing regional exploration and acquisition activities toward most favorable areas.

Jan 1, 1999

By D. Potter

Freeport Exploration initiated regional reconnaissance exploration programs in Irian Jaya, the easternmost province of the Republic of Indonesia in 1990 (see figure 1). Irian Jaya occupies the western half of the island of New Guinea. Freeport was awarded an initial contract of work which totaled 2.6 million hectares (6.4 million acres) and was subsequently awarded additional?concessions which added 1 million hectares (2.5 million acres). The concessions require work commitments and periodic relinquishments. Due to these relinquishments Freeport?s current land position totals l. 9 million hectares (4.7 million acres).

Jan 1, 1998

By J. Armstrong, J. Bourgeois, S. Warren

The application of statistical analysis software programs has proven useful for investigation of rockfall runout distance along a designed slope. Rockfall modeling programs are continually being upgraded with more sophisticated analysis tools, such as the use of the rigid body versus lump mass models. Engineers at mine sites utilizing the software may have varied experience related to these models, their associated input parameters, and how to interpret the generated results. To address this concern, researchers at the Spokane Mining Research Division (SMRD) of the U.S. National Institute for Occupational Safety and Health (NIOSH) investigated the influence of slope height, slope angle, slope material, and rock size for both rigid body and lump mass models in a 2-D statistical analysis program. Based on a literature search and industry input, specific ranges common to that of an open pit mining environment were chosen for each of the input parameters to determine 90% rock runout distance as well as their sensitivity to change. Data collected from this numerical analysis and simulation will be compared to empirical rockfall data gathered through the duration of the Highwall Safety project conducted by NIOSH from 2022–2026.

Mar 2, 2022

By F. Maciosek, D. Denton, J. Johnson

Researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health and personnel from Coeur Silver Valley, Wallace, ID, conducted tests using rock strain strips and Split-Set rock bolts instrumented with strain gauges to monitor wall rock strain at the Galena Mine, Osburn, ID. The objective of the test was to identify whether strain on the rock bolts increased prior to a rock burst. Although results were inconclusive, researchers learned that the Split-Set rock bolts yielded in stick-slip fashion in the highly jointed walls of the stope. The bolts were also bent as stress was redistributed following blasting and subsequent movement along joints in the wall rocks.

Jan 1, 2004

By SANDEEP KUMAR JENA

This paper reviews the recovery of potassium from different rocks and mineral sources. Global demand for potassium is rising steadily due to the growth of agricultural production. Fertilizer manufacture consumes the majority of the world’s potassium production, with other uses including those in the pharmaceutical, glass, ceramic, food and detergent industries. The availability of soluble potash (K2O) minerals, such as sylvite, kainite and carnalite, in countries like Canada, the United States, Israel and Russia makes them major potash producers, whereas agriculture-based countries like Liberia, Somalia, Central African Republic, Thailand, Indonesia, Malaysia and India meet their potassium requirements through imports only. In these countries, the huge availability of potassium-bearing rocks/minerals like nepheline syenite, feldspar, mica and glauconitic sandstone, containing around 4 to 17 percent K2O, brings up the prospect of commercial production of potassium. Potassium recovery from minerals/rocks is complicated due to the uniform distribution of potassium throughout the crystal structure. Different physico-chemical separation methods like bioleaching, chemical leaching, flotation and roast-leaching have been discussed for the successful recovery of potash values from these rocks/minerals. Although seawater is vastly available, the recovery of potassium from seawater using chemical precipitation, solvent extraction, membrane separation and ion-exchange methods is not cost-effective due to low concentration of potassium.

By J. Fritz, V. Gangrade, J. Briton, K. M. Ajayi, M. L. Harris, G. Cole, M. Young

Mine workers using diesel-powered equipment experience the highest occupational exposure to diesel particulate matter (DPM). This problem could be aggravated in underground stone mines due to their unique ventilation challenges with the large openings for airflow. Hence, adequate ventilation in these mines requires a combination of effective ventilation planning and delivering needed air quantities using auxiliary fans and stoppings. To meet this challenge, the National Institute for Occupational Safety and Health (NIOSH) developed the Air Quantity Estimator (AQE) software as a mine planning tool to help underground mine operators estimate the air requirements necessary to dilute DPM in the main air stream to statutory levels. The major parameters required for the calculations are the engine’s horsepower, DPM emission rate, the percentage operating time, catalytic converter efficiency, and filter efficiency. In efforts to provide major updates to this software, this study describes the recent development of a revised version of the Air Quantity Estimator (AQE 2.0). With the revised version, users have access to a comprehensive database of over 40,000 pieces of equipment, can define their specific target DPM level, and can create specific equipment for a customized database, in addition to having an improved easy-to-use interface. The software output provides an estimated total airflow necessary to dilute DPM based on the projected emissions, and the user can generate a related results report. The results also provide the mine personnel with a tool to identify vehicles that are high DPM contributors and could further be used to optimize the ventilation requirement by making changes to the percentage operating time of the engine. This software provides the mine with a user-friendly tool that could help reduce the DPM exposure of workers.

Feb 1, 2023

By Gordon Miner

GENERAL DESCRIPTION At the Star mine, Hecla Mining Co., located in Burke, Shoshone County, ID, the mining method is horizontal slicing (timbered or untimbered) cut-and-fill using hydraulic sand backfill. Back stoping as well as breast stoping is used; see Fig. 1. The annual produc¬tion from all cut-and-fill mining is 259 816 t (286,400 st). The average depth ranges from 366 to 2408 m (1200 to 7900 ft). A majority of the tonnage comes from an average depth of 2240 m (7350 ft). Average travel time to the stope is 1 hr. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size and Ground Conditions The ore body is 610 to 1219 m (2000 to 4000 ft) along the strike and 2408 m (7900 ft) on the dip, with an average vein width of 2.6 m (8.5 ft). The dip is essentially vertical. The ore body is heavily sheared and broken on the main fault structures; it is more competent on the wall veins but everywhere subject to rock bursting at depth. The hanging and footwalls are strongly fractured on the main fault structures, again more competent but still fractured on the wall veins. All host rock is Revett quartzite. Value and Production Requirements The ore value is $56 per ton. Production require¬ments are 1089 t/ d (1200 stpd), five days per week. Why Cut-and-Fill? The slusher extraction method is the most satisfac¬tory and practical for narrow vertical veins with sheared walls. The method must be quite selective to be com¬mercial. The veins are too narrow for rubber-tired ex¬traction and the grade is not high enough to make resuing practical. DETAILED DESCRIPTION Development Access to the main shaft is by the 3.2-km (2-mile) main haulage tunnel. The level intervals in the vertical timbered shafts are 61 m (200 ft). Vein development is by crosscut and laterals located 30.5 m (100 ft) into the vein wall. Vein crosscuts are on ±61 m (200 ft) centers. Access to the vein is by raises carried up with the stope. The raises are equipped with four wood¬cribbed chutes (two orepasses reinforced with angle irons, one manway, and one timber slide, Figs. 2-6). The initial cut is located 6.7 m (22 ft) above the main level (Fig. 1). Stoping Cycle Detail Sampling: Grab samples are taken from the mine cars. Channel sampling of the faces and backs is done when necessary. Drilling: For stope drilling, Ingersoll-Rand 300M percussion drills are used, with Ingersoll-Rand 300M and Gardner-Denver RB83M stopers, used for back stoping. Breasting down is done with Gardner-Denver S83FM jacklegs. The back stoping rounds are 0.9 to 1.8 m (3 to 6 ft) and the breast stoping rounds 1.5 to 3m (5 to 10 ft). Blasting: For stope blasting DuPont Tovex 100 watergel with fuses and igniter cord is used primarily. Approximately 60% of the blasting is done with am¬monium nitrate-fuel oil (ANFO). For development headings and shaft sinking, DuPont Drivex watergel with Ensign Bickford Nonel Primadet primers is is used. Mucking: Broken ore is removed entirely by slusher in the stopes. These are mostly 3.7-7.5-kW (5-10-hp) Ingersoll-Rand air-powered or 7.5-37.3-kW (10-50-hp) Ingersoll-Rand electric-powered. In the horizontal de¬velopment headings Eimco 12B and 21 and Atlas Copco LM-56 overshot mucking machines and a 0.76 (1 cu yd) hydroelectric Wagner HST-1 LHD (load-haul-dump) unit are used. Rockway for Extraction: The cribbed chutes (Fig. 7) are nearly vertical and hexagonal in shape and are made of spaced 152 x 203-mm (6 x 8-in.) timber, reinforced with varying weights and sizes of angle iron, depending on wear requirements. Rectangular cribbed chutes are used where ground pressure is not a problem. Cribbing is added in 2.4 or 3-m (8 or 10-ft) extensions accord¬ing to the floor height (whether timbered or untimbered). See Figs. 8 and 9. Backfilling: Backfilling is done with hydraulic sand consisting of classified mill tailings at 65% solids. The fill contains approximately 20% 325-mesh fines. The tailings are pumped 3353 m (11,000 ft) at 50-55% solids 22.7 dry t/h (25 dry stph) with a duplex piston pump. Cycloning increases the tailings density to 65% solids. Fill storage is in a 998-dry-t (1100 dry st) agi

Jan 1, 1982

By Ray Hutton, Darrell Liebno, Taro Nonaka

Background Population growth and increasingly stringent regulatory controls on water quality across North America have resulted in municipal governments investing heavily in infrastructure to control what are known as Combined Sewer Overflows (CSOs).These are events which occur when combined sewers exceed their conveyance capacity during periods of heavy rainfall or snowmelt. The city of Atlanta, Georgia is one such municipality; with a population of over450,000 within city limits and a sewer system servicing 1.2 million including adjacent jurisdictions, the City of Atlanta has a Combined Sewer System (CSS) encompassing approximately 15% of its total 3,540 km (2,200 miles) of sewers. Atlanta’s CSO discharges to local watercourses began to draw fire from environmental groups in the1980s. As a result, in the early 1990s, the City constructed a series of CSO control facilities which provided screening and chlorination at seven CSO discharge points across the CSS watershed. Unfortunately, these facilities were not capable of handling all of the overflows generated due to heavy storm events; frequently, untreated water was bypassed around the treatment facilities. The federal Environmental Protection Agency (EPA) deemed that water quality standards were being violated by these discharges, and a suit was brought against the City to force a higher standard of compliance. As a result, the City entered into a federal Consent Decree which would bring CSOs into compliance with federal standards by 2007. A critical component of this plan was the design and construction of the West Area CSO Tunnels and Pumping Station. In February 2003 the City’s Department of Watershed Management retained the services of Jordan Jones & Goulding/Hatch Mott MacDonald/Delon Hampton Associates (JDH Joint Venture) to design and provide construction management ser-vices for the project, which was designed to capture combined sewage from three of the City’s existing CSO facilities on the northern end of the CSS watershed. The design consisted of two connected tunnels which would convey the wastewater originating from the North Avenue, Clear Creek, and Tanyard Creek CSO facilities to a submersible wet well pumping station located at the R.M. Clayton Water Reclamation Center (WRC). Since the majority of the effluent stream consisted of storm water, the City elected to design and construct a separate treatment plant. This plant was designed under a separate contract, and is currently under construction.

Jan 1, 2007

By J. G. Groppo, A. E. Bland, B. K. Parekh, W. F. Stotts

Many coal preparation plants discard fine coal (generally minus 100 mesh) because it is difficult to beneficiate economically. At the Kentucky Energy Cabinet Laboratory (KECL), the waste streams from several Kentucky preparation plants were evaluated for cleaning with counter-current column flotation. A series of performance evaluations were conducted using a 0.05 m (2 in.) internal diameter (I.D.) 7.9 m (26 ft.) high laboratory column. The objectives of these tests were to assess the performance in terms of recovery and percent ash in clean coal and to optimize the operating parameters relative to combustible recovery and grade. Refuse streams containing 30-50 percent ash were upgraded to 2-8 percent ash with Btu recoveries of nearly 90 percent. A pilot scale column flotation cell was installed at the Bell County Coal preparation plant. This pilot plant utilized a 5.79 m (19 ft.) high and 0.15 m (6 in.) I.D. column to verify the performance data of the 0.05 m (2 in.) I.D. column for two different waste streams. Performance evaluation and pilot plant testing results related to scale-up are discussed.

Jan 1, 1988

By Bill Tucker, Mike Black

"PROJECT OVERVIEW Crossrail, Europe’s largest construction project, will increase London’s transportation capacity by 10% when it opens in 2018. The Crossrail scheme is a combination of surface and underground railway that stretches 118km east-west through central London from Reading, Berkshire and Heathrow airport in the west to Shenfield, Essex and Abbey Wood in the London Boroughs of Greenwich and Bexley in the east. Crossrail will serve 40 stations, ten of which are new, and bring 1.5 million people within 45 minutes commuting distance of London’s key central business districts. 21km of the Crossrail route comprises twin-tunnels beneath the heart of central London. It is the central section of the route, and the challenges that had to be overcome to construct its tunnels under the historic capital that forms the subject of this paper. The route of the Crossrail tunnels can be seen in Figure 1. These tunnels weave their way through the city’s underground landscape, linking eight new underground stations which connect to the existing London Underground network, providing interchanges with nine existing lines as well as the National Rail and Docklands Light Railway networks.Crossrail began construction of enabling works in May 2009 and launched the first of eight tunnel boring machines (TBMs) in May 2012. 42km of major tunneling work was completed in May 2015, and included 11km of sprayed concrete lined tunnels at the five mined stations (Bond Street, Tottenham Court Road, Farringdon, Liverpool Street and Whitechapel) in addition to the bored tunnel sections. The remaining three sub-surface stations at Paddington, Canary Wharf and Woolwich were constructed as large open boxes prior to the TBMs passing through. Crossrail, Ltd. is a special purpose company formed by the project’s joint sponsors, Transport for London and the Department for Transport, to manage design, construction and commissioning of the project. In 2009, Crossrail engaged Bechtel Ltd. as its delivery partner and a joint venture, Transcend (comprised of CH2M, AECOM and the Nichols Group), as its programme partner. The project is being managed by an integrated programme management team which is staffed by Crossrail and its partners. The railway, when opened, will be operated by Rail for London. With tunneling completed in accordance with the project’s master control schedule, the new railway is scheduled to commence dynamic testing in late 2017, with a phased opening of the tunneled sections and stations through Central London in 2018."

Jan 1, 2016

The 28th annual American Mining Hall of Fame Awards Banquet and fundraiser sponsored by the Mining Foundation of the Southwest will be held at the Marriott University Park Hotel, Tucson, AZ on Saturday, Dec. 4, 2010. The Mining Foundation of the Southwest is a nonprofit organization whose objectives are public education about the mineral industries, and recognition of outstanding accomplishments in and contributions to the fields of mineral and fuel resources. Funds are being raised to the support the foundation?s educational programs. Among these is the Educational Outreach Program operated jointly by the foundation and the Arizona Department of Mines and Mineral Resources.

Jan 1, 2010

By T. Y. Yan

O2, NaCl03, H202, NaOCI and Ce+4 have been examined as oxidants in an alkaline carbonate system for uranium in situ leaching. The South Texas and New Mexico ores contained up to 2.6 meq/g of reducing compounds that consume oxidants in the leaching operation. Leaching rates did not increase linearly with the oxidation potential of the oxidants. A mild oxidant can be used to maximize uranium oxidation selectivity and oxidant efficiency. 02 can oxidize most of the uranium mineral with an adequate rate and high oxidant efficiency.

Jan 1, 1993

By Paloma Lazaro, Moe Momayez

Heat-related illnesses (HRI) are relatively common in both hot surface and underground mining operations. When workers are exposed to extreme heat or strenuous work in a hot environment, they become prone to heat stress. Heat strain is the result of the body’s response to external and internal heat stress. It is therefore vital for the conditions leading to heat strain be detected and treated in a timely manner. Heat-related illnesses are manifested by exhaustion and heat stroke. The predicted heat strain (PHS) [ISO 7933 (2004)] model has been developed to predict the health condition of the worker in terms of core body temperature and water loss. The PHS model tested in this study is based on eight physical parameters that are measured at different intervals during a work shift. They include air temperature, humidity, radiation, air velocity, metabolic rate, clothing insulation, posture, and acclimatization. The model predictions are then compared with a direct physiological measurement, such as core body temperature. We present the results of an extensive study that monitored and predicted body’s response to heat stress under different environmental and working conditions. The PHS model provided reliable results in most instances in comparison with other prediction methods currently in use in the field.

By A. E. Isaacson, D. B. Dreisinger, G. A. Kordosky

The U.S. Bureau of Mines is researching the application of solvent extraction technology to highly acidic (pH < 1) copper leach liquors. As increasingly complex copper ores are mined for leaching, use of highly acidic leach solutions maybe necessary to effectively recover the contained metal values. A mixture of two commercially available extractants, based on aldoximes and substituted 8-hydroxyquinoline, which has a high transfer efficiency has been identified. A synthetic leach liquor, containing 5 g/L Cu at pH 0.9 was processed utilizing the mixed extractant and a laboratory SX circuit. The loaded organic was stripped with a synthetic barren electrolyte compatible with electrowinning technology.

Jan 1, 1993

By G. Goellner

The thick alluvial sand and gravel deposits along the base of the San Gabriel mountain range in Southern California area have been mined for construction aggregates for over 100 years. Encroachment of high-density urban populations in this area has led to concentrated mining in a handful of open pit mines with single production faces reaching up to 55 m (175 ft) in height, and long transportation distances from the pit to the processing plant. Aggregate producers have responded to these challenges by developing innovative mining systems which enable low-cost, full-face mining of the alluvial material, and low cost delivery of this material to the plant.

Jan 1, 2004

By Paweł Stefaniak, Natalia Duda-Mróz, Sergii Anufriiev, Wioletta Koperska

Due to the high environmental risks and negative impact of a failure, tailings storage facilities (TSFs) need constant monitoring. Advanced mathematical models have been developed in the past to predict the behavior of TSFs and raise alerts if needed. To be precise and reliable, such models need a spatial distribution of soil types within the dam as an input. Getting this data from laboratory measurements is time and costconsuming. In this article, we propose an ANN-powered algorithm, which allows us to accurately estimate the soil distribution based on a cone penetration test (CPT).

Jun 25, 2023