Search Documents

By S. R. S. Sastri

By using the data of E.A. Hersam and F.C. Bond's equation for energy consumption in comminution, a method was developed to analyze the performance of industrial jaw crushers. The study showed that industrial jaw crushers are generally operated below capacity. The study also showed that industrial jaw crushers generally have sufficient installed power to operate at, full capacity. The method presented can be used to estimate the capacities and power requirements of jaw crushers.

Jan 1, 1995

By B. Mishra, A. Staley, D. Kirkpatrick

The major waste product of the alkaline extraction of alumina from bauxite [Bayer Process] is known as red-mud. Approximately, a ton of red-mud is produced for every two tons of bauxite mined. The red-mud produced from Jamaican bauxite is rich in hematite, alumina and titanium oxide. It has been shown that over 90-wt. pct. alumina can be recovered from red-mud by soda-ash sintering and caustic leaching. Hematite can be carbothermically reduced with a degree of metallization of over 94 pct resulting in attempts for magnetic separation. These separations are desirable in the notion that there is no waste product generated from this type of processing and consequently an opportunity for complete utilization of the waste material. Conversely, the pre-separated material could be charged through the tuyeres in an iron blast furnace or smelted to produce pig iron. If smelted, the concentration of titanium oxide in the slag will be significantly high justifying its recovery by established acid-leach process. This paper describes the results of alumina recovery and the plans for titanium oxide recovery from red-mud. In addition, the situation of ongoing efforts in iron extraction, particularly, the method of magnetic separation of the reduced material. The problems associated with the use of reduced red-mud as an alternative to direct-reduced iron [DRI] has also been discussed. Critical assessment of the recovery sequence chosen for the products has been described based on economics.

Jan 1, 2001

By Rolf B. Pedersen, Ana Filipa Marques, Ingunn H. Thorseth, Ingeborg Okland

"Deep sea mining of polymetallic sulphides will change the physical and chemical conditions at the seafloor by creating scars when sulphides are removed, and potentially also by deposition of mine tailings at the seafloor. These changes will impact the existing ecosystems at the seafloor in and around the mined areas. Seafloor Massive Sulphide deposits that have been exposed to oxic seawater weather into Fe-metal-oxyhydroxides. However, the rates of weathering and release of heavy metals and other toxic compounds to the environment from freshly exposed sulphides in a deep-sea environment are not well studied.During a cruise to the Arctic Mid-Ocean Ridge in the Norwegian-Greenland Sea in July 2014 we will initiate in-situ experiments investigating the microbiological and geochemical processes involved in the weathering of freshly exposed massive sulphides deposits in a natural environment. This will be done by creating scars in naturally occurring sulphide deposits and by deploying weathering experiments at the seafloor. The sites will be revisited and re-sampled in 2015. The mobility and fate of heavy metals will be one of the main concerns of the study as well as constraining the time it will take for exposed sulphides to return to the chemical state present prior to mining. In this presentation we will present the experimental framework and the preliminary results from the July 2014 cruise. This project is part of the EU funded MIDAS (Managing impacts of deep sea resource exploitation) project."

Sep 1, 2014

By Roger L. King

Working in gassy ground conditions is an everyday occurrence for the U.S. coal mining industry. As tunneling operators begin to venture into projects that expose them to the additional hazard of potentially explosive atmospheres, lessons learned by the mining industry over years of experience should be transferred into this industry. This paper will present practices developed by the U.S. coal mining industry for dealing with the problem of excavating material in potentially explosive atmospheres. Procedures will be discussed that can be used to detect and quantify gas prior to mining that have application to the construction industry. Degasification or drainage practices, including predrainage from vertical and horizontal boreholes, will be discussed. Also, ventilation practices commonly used in the mining industry will be presented.

Jan 1, 1985

The US Constitution provides for regulation by the states for protecting the public's safety, health, and welfare. Hence, in the eyes of the law of all states today, this is the sole justification for registration of professional engineers. Wyoming was the first state to register professional engineers in 1907, to correct abuses of incompetent or fraudulent practices in surveying and real estate. Public safety and health are most directly affected by civil, electrical, and mechanical engineering. Other branches of engineering have a profound effect on the public welfare, including investors, and safety and health of employees. No arguments, pro or con, are valid except in relation to the registration laws of various states. Code of Ethics Few would argue the desirability of requiring conformance with a code of ethics. A major problem lies in enforcing compliance, since protecting the public demands a high standard of competence, yet assessing competence gets confused with restraint of trade. Bidding engineering work on price competition can lead to pressure to cut corners on engineering quality, and was therefore discouraged by codes of ethics. The Supreme Court, in a suit against the National Society of Professional Engineers (NSPE), barred any engineering society from such bidding restriction. It has, however, upheld the right of states to impose codes of acceptable practice as part of registration laws. For example, Texas Canon I reads, "The engineer's paramount professional responsibility should be the safety, health, and welfare of the general public." Anything less makes the code practically meaningless, but there are potential conflicts of interest in many engineering organizations. How can conflicts be handled? Any corporation could improve its public image by adopting a policy that each employed PE should, without fear of recrimination, record in writing over his seal any problem or flaw in any design that comes to his attention. The policy should further require that his superior provide him a written reply pointing out that the "flaw" is accepted as requiring correction or as a calculated risk, or overruled as erroneous or as a difference of opinion. Errors in calculation of judgment are inevitable. Despite this, there are limits to how much time and money should be spent to eliminate them. It is difficult, however, to see any excuse for failure to conscientiously evaluate the opinion of a PE. This may be an impossible ideal, but how else can the profession or the industry have credibility? The National Council of Engineering Examiners (NCEE) has a code of ethics one presumably subscribes to by signing an application to write a Principles and Practices examination. However, NCEE has none of the power of enforcement that is available through state boards of registration. Registration Qualifications Qualifications are set by the laws of the states. In general, they require passage of an eight-hour examination in fundamentals, preferably at graduation, and, later, one in principles and practices. The examinations are compiled and distributed by NCEE. This system provides for a high degree of uniformity and reciprocity. States set the education and experience levels (typically four years after graduation) required by those desiring to write the principles and practices examination. Examinations The principles and practices examination calls for answering eight of 20 equal weight questions; one on engineering economics, 19 on engineering. Economics may enter into engineering questions, but only provided the question is not answerable by an economist without engineering training. In preparing examinations, NCEE strives to use questions that require some judgment and can be more effectively answered by someone with four years experience beyond college. The aim is to assess entry-level professional

Jan 2, 1984

By T. C. Pool

Physical and chemical conditions permitting, in-situ leaching (ISL) of uranium offers a variety of advantages over conventional production methods including less surface disturbance and less solid waste. Commercial production of uranium by in-situ leaching techniques was initiated in 1963 in the Shirley Basin of Wyoming by Utah Construction. On a world-wide basis, ISL uranium production amounted to about 13.2 million pounds U3O8 in1999, approximately 16% of world output. Both acid and alkaline systems are used, the selection of which is primarily dependent upon groundwater quality and related reclamation requirements. ISL offers low capital costs per unit of annual capacity and is particularly flexible in adapting to changing market conditions.

Jan 1, 2000

By R. P. Stahura

Conveyors are the lifeline of mining and processing operations. They continuously supply materials to and carry finished products and waste away from operations. When conveyors are running at less than maximum efficiency, the operation's productivity is in trouble. Inefficient conveyors suffer carryback, leading to the buildup of materials on idlers and other expensive components. They spill and leak material at loading zones and conveyor transfer points. This causes accumulations that can damage the belt, wear moving components and increase both clean-up labor and maintenance expenses. They wander or mistrack, spilling material and endangering personnel and conveyor components. And through these inefficiencies, they multiply the operation's hidden costs. These added expenses occur in lost production, increased downtime for service and maintenance and replacement costs for prematurely worn equip¬ment. In addition, the attitude that inefficiency is "good enough" is recognized elsewhere in the organization. As a result, other departments relax or operate at less than peak performance. Quality goes down along with employee morale. Costs of inefficient conveyors A key to efficiency is handling a product as few times as is necessary. That means conveyors should be loaded, track true to the unloading point and then be unloaded, all without material escape or waste motion. An inefficient conveyor is often signaled by accumulations of DURT - material that has escaped from the system and is now at large in the plant. This DURT adds costs to an operation that are uncounted and, perhaps, uncountable.

Jan 1, 1992

By T. Tafi

The Ute-Ulay project area is located approximately five miles west of Lake City, in Hinsdale County, Colorado. The Ute-Ulay Mine site is approximately one mile east of the project area. The elevation of the site is 9,200 feet and is adjacent to Henson Creek (Figure 1) [ ] The Ute-Ulay Mining complex is an inactive gold, silver, and zinc mining/milling operation, that operated from the 1880?s until the 1970?s, and sporadically into the late 1990?s. The mining complex comprises several levels of underground mines, a flotation mill, and an abandoned town site. Due to the narrow, steep sided canyon, milled tailings were pumped upstream one mile in a sluice box to a wider section of the canyon, and deposited into five tailings impoundments and one berm located between the impoundments. An estimated 9,000 cubic yards (yd3) of fine grained tailings were located in the impoundments adjacent to the creek. The Ute-Ulay project area consisted of the mill tailings impoundments located upstream from the historic mine.

Jan 1, 2011

By G. Duncan, K. Winther, R. Ericsson

Distinct trends in grinding mill technology have emerged in recent years. In an effort to optimize overall mill performance for the needs of the End User, broad measures of logistical speed, process flexibility, operational risk, and overall costs now exert greater influence on the specification of grinding equipment. As a result, innovative alternatives to conventional grinding mill structures, supports, drives, feed, and discharge configurations are now being offered and selected with greater frequency. This paper investigates these trends in grinding mill technology, utilizing optimization and decision-theory techniques. In particular, the paper considers how specific advances in process design, product engineering, manufacturing techniques, and mining operations continue to relax technological constraints, enabling further mill innovation. In this context, a methodology is presented, illustrating how proper selection and specification of grinding mill components and configuration can target an optimization of the four End-User performance measures listed above.

Jan 1, 1999

By Antoni Kalukiewicz

From 1997 through 2000, a team of Polish experts headed by the author studied the prospects of mining newly discovered emerald deposits in Afghanistan. This article describes the scheme for mechanization of the mining operations, along with improvements made to the ventilation facilities and lighting. The required equipment was flown to Afghanistan and the Afghan miners were trained in machine operation and maintenance.

Jan 1, 2005

In conjunction with steady increases in production levels, longwall operators have applied greater quantities of ventilating air and spray water in an effort to control respirable dust and/or methane. Air velocities greater than 7.6 m/s (1500 fpm) have been measured on longwall faces. Operators have expressed concern over the potential entrainment of respirable dust at these high velocities. The greatest likelihood for entraining dust into the high velocity airstream may occur as shields are advanced allowing relatively dry particles to fall from the shield canopy directly into the airstream. Laboratory tests to simulate dust liberation during shield movement were conducted at the Pittsburgh Research Laboratory of NIOSH at velocities ranging from 2.0 to 8.2 m/s (400 to1600 fpm). Airborne dust samples were obtained with personal impactors to quantify the size distribution and concentration of the dust entrained at the various air velocities. Statistically significant increases in both total and respirable dust concentrations were measured as test air velocities were increased.

Jan 1, 2001

By William M. Gleason

Hard times continued to plague the industry when the calendar rolled over to 2000. During 1999, the United States economy had grown vigorously, capping the longest economic expansion in United States history. However, the mining industry was not so fortunate. Commodity prices remained in a slump in the “new-economy” that was fueled by excitement and speculation about the power of the Internet during the infancy of the Information Age. Much of the investment money that once went to mining and exploration was now headed to the world of virtual gold mines. SME President Donald E. Ranta implemented new technology into his plans for SME. His two major goals were new membership growth and to foster the establishment of the comprehensive Internet presence for the Society’s technical information. His strategic priorities included enhancing the quality and quantity of publications, programs, meetings and short courses. “The Internet is the vehicle that will advance the priorities,” he said.

Jan 1, 2007

By Debbie Laney

DOUG HALBE: Second in our quick run-through on "Operating Ideas That Have Saved Me Some Bucks," was Debbie Laney of Rayrock Mines. Debbie apologizes. She can't be here. But she said, "Doug, don't worry. I've asked Mary Korpi to present the paper. We're both short, blond, and wear glasses. Nobody will know." [laughter] Mary, I caught it right away. You ladies can't fool us. Debbie, who wrote the paper, has spent almost her entire career in operations. She is currently metallurgical manager of Rayrock Mines in Valmy, Nevada. Mary Korpi is also a real operator (that doesn't sound right). She has been responsible for a number of operating areas at Newmont's Nevada operations, and she is currently taking a break from operations as manager of public relations/employee communications for Newmont Gold in Carlin. MARY KORPI: They told us this year at Newmont that we were going to have to work twice as hard. I had no idea it meant I would have to work for another company, too. Over the years, and many times in association with work for mid- to small-size mining companies, there have been two areas that seem to have been the focus of cost savings when looking at new facilities or new processes.

Jan 1, 1998

By Jon Y. Kaneshiro, Sean A. Menge, M. Luis Piek, Brian Barker

The Lake Hodges to Olivenhain Pipeline project is part of a 40-megawatt pumped storage project linking two reservoirs as part of the San Diego County Water Authority’s $939 million Emergency Storage Project. Seeking to expedite project completion, the project was advertised as Design-Build, a first for the owner. Awarded to Kiewit Pacific with Parsons as designer, the 1,750m (5,700ft) long, 4.25-m (14 ft) horseshoe tunnel was excavated with conventional drill-and-shoot technique. The mining method was well suited to deal with the shear zones, the very abrasive rock, and 13.3% and19.6% grades. At the apex of the alignment, a 60m (200ft) by 3.6m (12ft) diameter raisebore shaft with surge chamber to protect against pump malfunction was constructed. Upon completion of mining, the tunnel was lined with a 3m (10 ft) diameter high strength steel pipe. Scheduled to come on-line by January 1, 2008, the Lake Hodges to Olivenhain pumped storage project is valued at $108 million, delivering a reliable source of water in emergency situations and electricity-generating capability to meet the growing demands of the San Diego region.

Jan 1, 2007

By George A. Mealey

Caving mining methods that are based on a planned caving of rock above and/or at times surrounding the material being mined can be classified in three broad categories: longwall mining, sublevel caving, and block caving. Each of the three methods involves a distinct technology as well as art of operation. Each requires a relatively large, regular, and predictable ore body. As a rule, the effect of mining results in some form of impact or change on the surface. Operationally, underground caving methods are characterized by high productivity as well as a high percentage of extraction of the mineral being mined. A key element for the productivity of this form of mining is the ability to standardize the various elements of work taking place underground. Therefore, work-men may perform a specialized role rather than function as all-around miners. Further, the nature of the mining methods lend them to a high level of mechanization. Operations and manpower can be centralized into a relatively small area where supervision can be concentrated and therefore be more effective. Productivity as well as safety benefits thereby. The caving method is unique in that the exploitation openings are deliberately destroyed by the process of mining. Rock mechanics principles focus on the ensurance and the propagation of the cave as well as the continuance of the mine openings designed to extract the broken ore. As a rule, production operations are designed to maintain a steady, continuous flow of ore from the extraction areas. This steady flow rather than an intermittent flow tends to promote good caving action as well as reduce hangups.

Jan 1, 2008

By A. J. Wainwright

The Coffee Creek lode gold discoveries are located in the White Gold district (Dawson Range), west-central Yukon, 130 km south of Dawson City and 30 km south of the Golden Saddle gold deposit (Figure 1). Extensive structurally-controlled gold mineralization has been discovered during the 2010 and 2011 exploration drilling campaigns, highlighting this part of the Dawson Range as a significant emerging gold district. [ ] In this contribution we review the geological framework and describe the mineralization styles and metal signatures observed to date on the Coffee project. The main Coffee area is underlain by a 15 km by 4 km geochemical footprint, characterized by discrete linear gold-in-soil anomalies that correspond to various mineralized corridors. Of several mineralized areas tested in the past two drill seasons by diamond core and reverse-circulation (RC) drilling, we focus on the Supremo, Double Double, Latte and Kona zones; areas with the most information obtained from drilling thus far (Table 1; Figure 2).

Jan 1, 2012

In February 2001, Kalgoorlie Consolidated Gold Mines (KCGM) commissioned its first full-scale ultra fine grinding (UFG) plant to supplement existing roaster concentrate treatment capacity. This process involves the fine grinding of refractory pyritic concentrate to 10µm, followed by direct cyanide leaching for the recovery of gold. By this means gold is economically extracted from the concentrate without the need to first oxidise the host pyrite. This paper details the history of the project from initial laboratory testwork comparing possible treatment options, to current performance of the 12 tph plant. This includes the cost comparison of the major treatment options, the laboratory and pilot scale UFG performance, the UFG mill selection, cyanide leaching of UFG product, commissioning and plant performance to date.

Jan 1, 2002

"The National Mining Hall of Fame and Museum (NMHFM) announced the 2018 National Mining Hall of Fame inductees. This year’s inductees, selected by the National Mining Hall of Fame’s Board of Governors, represent exploration, extraction, management, education and research and development in the U.S. mining industry. Their contributions have had significant and lasting impacts on the mineral and mining industry; these individuals were selected for being mavericks, thought leaders, researchers, educators, mentors, wealth builders and philanthropists.Professor John M. Guilbert, Dr. Leo J. Miller, Robert E. (Bob) Murray and Douglas (Doug) B. Silver will join 240 other mining industry luminaries when formally inducted into the National Mining Hall of Fame on Sept. 29, 2018. Additionally, the Prazen Living Legend of Mining Award will be presented to the Freeport- McMoRan Foundation. The 31st Annual Induction Banquet and Ceremony will be held at the Ritz-Carlton in Denver, CO.2018 National Mining Hall of Fame inducteesProfessor John M. Guilbert was a renowned geologist and professor of economic geology at the University of Arizona; he had a distinguished 50-plus year career in academia and business. Guilbert, together with J. David Lowell, worked on the most important breakthrough in mineral exploration in the last 100 years, the Porphyry Copper Model. This work, known as the Lowell and Guilbert Model, was utilized by exploration geologists worldwide over the next four decades to discover hundreds of millions of tons of copper metal and numerous profitable mines including the prosperous Bajo de la Alumbrera copper mine in Argentina. Guilbert was a founder of The World Museum of Mining in Butte, MT. He was the recipient of countless awards including the Society of Economic Geologists (SEG) R.A.F. Penrose Medal as well as the D.C. Jackling Award from the SME.Dr. Leo J. Miller was a maverick in the mining industry and no armchair geologist. He believed that active fieldwork, on foot with a rock pick, was indispensable for exploration. His basic tenet was to absorb as much information about an exploration target up front, formulate ideas – sometimes novel ones — and then get out into the field to prove those ideas. Miller was known to diverge from the standard interpretation of the geological processes, which formed the mineral deposits, and to apply innovative applications of high-tech tools to more usual exploration programs. This approach resulted in a 50-plus year career that included the discovery of the Kidd Creek massive sulfide deposit and the development of the Lee Creek phosphate deposit; which other explorers had previously given up on, believing whatever phosphate might be present would be too difficult and expensive to mine. The recipient of many honors and awards, Miller received the SME Robert M. Dreyer award in recognition of outstanding achievement in ore discoveries."

Jan 8, 2018

By Jim Baumann

Deposited millions of years ago in irregular paleokarstic channels, Jamaica’s extensive bauxite deposits provide good quality ore for alumina production and subsequent aluminum smelting. Bauxite mining operations are critical to the Jamaican economy. It accounts for a large percentage of Jamaica’s export earnings. Bauxite production in Jamaica accounts for about 10% of the world’s output each year. Bauxite deposits in Jamaica lie close to the surface. They can be extracted using standard surface mining techniques. The deposits occur in scattered pockets across the country’s rugged landscape. So it was necessary for two of the country’s major mining and refining operations to implement cost effective methods for the acquisition and management of bauxite reserves and surface ownership distribution rights.

Jan 1, 2002

By G. A. Grandy, P. F. Thomas, C. D. Danecki

When considering the mill drive system for a grinding application, a large number of questions must be answered. Depending on the mill size and type, the mill can be driven by several configurations of drive systems: a single low-speed motor connected to a pinion driving a ring gear, two low-speed motors connected to two pinions and driving a ring gear, or a gearless motor mounted directly. In addition, a gear drive system can have a reducer placed between a high-speed motor(s) and pinion(s) or a power path splitting pinion stand. In some designs the reducer is integral with the pinion stand driven by a high-speed motor. The technical and commercial implications of several mill drive options are presented. Initial cost, cost of installation, cost of commissioning, and cost of operation and maintenance are presented for each drive option considered. The impact of each drive system on the design, cost and operation of the overall plant electrical system is discussed. Also, consideration is given to mill drive availability, and the potential cost resulting from delays in plant production.

Jan 1, 2001