Search Documents

By Y. J. Wang

This paper describes a procedure for solving the generalized system of n network equations in n unknowns considering the following ventilation variables and parameters: (a) air quantities, (b) pressure losses or gains caused by the control devices (i.e., fans or regulators), (c) resistance factors, (d) natural ventilation pressure, and (e) fan pressures (as a function of air quantities). The air quantities and pressure losses for all branches in the network are grouped into dependent and independent variables. The branches with an independent quantity are contained in a chord set, and the branches with a dependent pressure loss are contained in a chord set. In addition to the problem formulation, the solution procedure, applying the Newton method, is discussed and illustrated with a numerical example.

Jan 1, 1989

By Ryan Marsters, Adam Pring, Robin Dornfest

Raw water supply in the central Rocky Mountains often relies on trans-basin conveyance. Many of these older diversions incorporate high-elevation, miles-long tunnels driven over a century ago in hard rock. Tunnels were excavated using conventional drill-and-blast mining and weak ground was supported by timber sets and other various means. Over time, timbers rot and fail, rock quality deteriorates, and the timbers are gradually replaced by more timber, steel patches and braces, formed concrete, rock bolts, split sets, shotcrete, and other means which are commonly applied over existing support, thereby reducing tunnel cross sections, obscuring previous support systems, and rarely addressing the failing rock itself, leading to further deterioration of both the rock and the existing support. Traditional investigation techniques to assess compromised areas are often unfeasible due to access, depth, rubble and voids behind weight-bearing existing supports, confined space, poor invert conditions, poor ventilation, and flowing water. This presentation will discuss design procedures for assessing obscured ground conditions, assigning support classes which accommodate for unknowns, and implementing contractual means to address inevitable surprises or quantity overruns. Case studies include raw water supply tunnels in the Rocky Mountain region constructed between early to mid-20th century.

Dec 1, 2022

By T. P. Meloy

The packed column flotation cell is an awesome separation device. Virtually unknown and untested, the packed column flotation cell is one of the ten most important developments in mineral processing of the 21st century. Though experimental and industrial data is limited, it is clear that the packed column flotation cell is two to three orders of magnitude better than the conventional flotation cell and one to one and a half orders of magnitude better than the open column flotation cell. With the modern packing taking up less than one percent of the packed column, column blocking does not occur. For a packed column operating 24 hours a day, 365 days a year, the estimated mean time between failures (MTBF) is one hundred thousand hours or roughly twelve years. With no moving parts, lower maintenance costs, lower power consumption and inherent operating stability, the packed column is a powerful separating machine. Because there is little meaningful data for comparing the packed column to the conventional flotation cell and the open column flotation cell, much of the material presented in this paper are guesstimates. They are disinterested guesstimate made by the authors after extensive theoretical work and reviewing the known facts. In the authors' opinion, no available data contradicts the guesstimate. The authors expect that there may be errors as large as three hundred percent. Even three hundred percent errors will not change the conclusions of this paper. The packed column flotation cell is a formidable separating device. To understand the problems of comparing the three types of flotation cells, consider the fact that the three cells may have different modes of separation. One of the authors, Meloy, believes that in the conventional cell, the primary particle separation takes place in the liquor with secondary separation taking place in the froth, while for open column flotation, all the separation takes place in the froth. However, he believes that in the packed column a large part of the separation may take place on the walls of the packing. If this is true, not only is the method of modeling each type of cell different, but the method of particle selection in the cell is different. This means that one type of cell may be better at differentiating between two different types of particles. There is a growing body of literature on open and packed column flotation. Suggested reading: (Clarke et al; Hucko et al; Li; Smith & Warren; and Yang).

Jan 1, 1994

By Donald L. Bott

A computer model called the Quality Compliance Model was developed to optimize the mine planning and sequencing in area coal mining with respect to the limit on pounds of sulfur dioxide per million BTU imposed by regulations. The objective of the model is to maximize the amount of high sulfur coal mined from various benches while meeting the specified compl'ance standards. Given multiple seams and multiple benching operations, the mining sequence from each pit is simulated. The rate of mining is controlled such that the in-pit blending will maximize the usage of high sulfur coal and meet compliance standards. The compliant coal can be stockpiled for usage at a later date, or it can be disassociated. This calculation can be based on any given rate of production, i.e., from as small a unit as a unit train to as large as monthly or yearly production.

Jan 1, 1982

By K. Hanumantha Rao, K. S. E. Forssberg

The limestone deposit of Gâsgruvan, Sweden contains around 89.2 per cent of calcite. Conventional and column flotation studies have been carried out using sodium oleate and modified fatty acid collectors in the presence of sodium silicate modifier. The effects of collector and silicate concentrations, and particle size on the flotation response of calcite have been investigated. The results have been discussed in comparision to the performance of conventional and column flotation cells. The feed size is found to be a significant factor to achieve a high grade calcite concentrate either by conventional or by column flotation. The loss of selectivity at fine particle sizes is examined using a modified DLVO theory.

Jan 1, 1995

By Jean-François Boucher, Ernest K. Yanful, Mei Lin Shelp, Lionel J. J. Catalan

Shallow water covers for preventing acid production in tailings are based on the principle of minimizing oxygen availability. Resuspension of material from the tailings bed may result in increased oxidation and metal releases since dissolved oxygen is at near saturation levels in the water cover. Resuspension can be caused by waves and currents strong enough to mobilize the surface of the tailings bed. Tailings resuspension was measured with sediment traps in the Upper Cell of the Heath Steele site near Mirarnichi, New Brunswick Canada. Although significant amounts of resuspended tailings were collected in all traps, analysis of resuspended solids and bed tailings suggests that for the observed wind conditions resuspension did not occur at locations where the water cover depth was greater or equal to 1.0 m. Currents were likely responsible for the transport of resuspended tailings from shallower areas to locations where the water cover was deeper than 1.0 m.

Jan 1, 2000

By R. C. Gilmore, A. Juganda, Jr. Bogin, S. Saki, S. A. Lolon, J. F. Brune, Jr. Zipf, J. W. Grubb

"Methane-air mixtures form explosive gas zones (EGZs) in underground longwall coal mine gob ventilation systems. Such EGZs have caused a number of fatal mine explosions, including the 2010 disaster at the Upper Big Branch mine, where 29 miners lost their lives. Researchers at the Colorado School of Mines use Computational Fluid Dynamics (CFD) modeling to predict EGZ locations. In this paper, a model of a bleeder-ventilated gob system includes two adjacent panels, an active longwall and a mined-out gob. Boundary conditions for the simulations match statutory ventilation conditions for methane concentrations and air flow rates at common measurement points throughout the mine. The modeling results predict the persistence of EGZs in the gob that may compromise the effectiveness of the bleeder ventilation system. INTRODUCTION Mine operators must maintain statutory air flow and air quality requirements at various locations throughout the mine ventilation network. U.S. regulations generally require mine operators to establish bleeder ventilation systems surrounding longwall gob areas (30 CFR §75.334.) Gilmore et al. (2015) documented that explosive gas zones (EGZs) exist within bleeder-ventilated gobs and may extend into the bleeder entries that must be examined weekly, presenting an immediate fire and explosion hazard to mine examiners. In a project funded by the National Institute for Occupational Safety and Health (NIOSH) under contract 200-2009-31409, researchers at Colorado School of Mines have developed a tool for modeling gob air quality using Computational Fluid Dynamics (CFD). This CFD model is capable of examining a wide range of longwall mine ventilation systems. Marts et al. (2014a, 2015) studied progressively sealed gobs with U-type ventilation and using a back return. Saki et al. (2015) examined the impact of gob ventilation boreholes and face air quantity effects on tailgate methane concentrations. Gilmore et al. (2014) modeled bleeder-ventilated gobs and Gilmore et al. (2015) studied the effects of bleeder regulator settings on EGZ volume and locations in the gob. CFD studies for progressively sealed gobs were generally carried out using 5000 ft (1500 m) panels because the gob atmosphere remains largely unchanged from about 500 m (1,500 ft) inby the face. A modular meshing methodology (Gilmore, 2015) permitted researchers to extend bleeder models to 10,000 ft (3050 m) to include the full extent of bleeder entries. This paper further expands the bleeder CFD model to study the gob atmospheres of two adjacent longwall panels, each 10,200 ft (3100 m) in length, with the active face located 6,700 ft (2040 m) from the startup room."

Jan 1, 2016

By J. J. Kellar, W. M. Cross, H. Du, C. D. Struckman, D. A. Boyles

Silane coupling agents have been used in the filler industry for years. One particularly unique feature is the ability of the coupling agents to enhance the adhesion between filler and polymer matrices. This paper will review the use of coupling agents for polymer matrix composite applications and discuss a new approach to coupling agent chemistry, namely, direct formation of a silicon-carbon non-hydrolyzable linkage between glass and coupling agent. The grafted silane monolayers were evaluated by infrared spectroscopy to ascertain their surface coverage and relative stability. Finally, composite specimens were fabricated and their mechanical properties were compared with traditional silane coupling agent treatment.

Jan 1, 2003

By G. I. Karydakis

Geothermal energy is an important energy asset which can play a significant role in providing energy resources to cover energy needs of a country while it can play a primary role in a particular region where it is abundant. Greece is especially rich in geothermal energy. The collision of Euroasiatic and African plates coupled with the strong tectonic tension, particularly in north Greece, resulted in the formation of important geothermal fields of low, medium and high enthalpy. These fields are in the Aegean islands, in central and east Macedonia, in Thrace and in central Greece. This work presents and analyzes information about the drilling activity for exploration and production of geothermal fields of low, medium and high enthalpy in Greece for the past thirty years. The number and type of wells drilled together with the spatial and the yearly distribution are given. Depth data has been analyzed according to the fluid temperatures and to the geological formations. Cost data are presented and analyzed for the total number of wells drilled giving also the cost per meter drilled.

Jan 1, 2006

By Victor F. Hollister

Porphyry copper deposits can be categorized into three models for purposes of prospect evaluation: Breccia-pipe, modified Lowell and Guilbert, and diorite models. The modified Lowell and Guilbert model is normally associated with a quartz-bearing intrusive and a potassic, phyllic, argillic, and propylitic alteration sequence. Variations can occur in the alteration zones of this model that range from orthoclase-rich (Kalamazoo, Silver Bell, and Mineral Park) to ortho- clase-deficient (Petaquilla and Bougainville) potassic zones. The unifying features of the model are the presence of a phyllic zone and a quartz-bearing intrusion. The breccia-pipe model (Toquepala) is characterized by structure and alteration related to or controlled by breccia. Where tourmaline occurs in the breccia, the identity of the model is usually clear. However, if tourmaline is not commonly developed in the breccia (La Caridad), the deposit can be misidentified as to model. Porphyry copper deposits associated with quartz-deficient intrusives, whether these are calc-alkalic diorites or alkalic plutons, are characterized by alteration suites distinct from those of the modified Lowell and Guilbert model. These have been generalized as diorite model porphyry deposits. Because alteration and mineralogical development in diorite model deposits is distinct from that of the modified Lowell and Guilbert, ore guides and exploration tactics differ for the two models. The reprint that follows describing the three prospecting models summarizes their features. It is to be emphasized that these are models used in exploration for specific deposit types and are not genetic, tectonic, or geographic models. Porphyry copper deposits can be metamorphosed. Gibralter is an example of a Lowell and Guilbert model deposit that has undergone regional metamorphism.

Jan 1, 1991

By C. Maltesh, P. Somasundaran

The ever increasing need for treating fine complex mineral bodies has led to the evolution and rapid development of advanced processing techniques for fine grinding, classification an if mineral separation and purification. With the introduction of these new technologies and understanding of underlying fundamental principles, mineral processing is now being applied to materials ranging from ceramics and composites to superconductors. In this review, current and potential applications of mineral engineering techniques to advanced materials processing are discussed. Particularly, material processing involving ultrafine grinding, dispersion and flocculation and thin film formation is examined. Novel techniques of solid/liquid separation involving manipulation of interfaces and use of high intensity high gradient superconductor magnetic equipment for solid/solid separation are discussed.

Jan 1, 1990

By John W. Conn, Harry C. Verakis

An explosion in an underground coal mine can have a devastating effect on the main fans used to provide mechanical ventilation. The Code of Federal Regulations, Title 30, Part 75.310 (CFR, 1992), specifies that each main mine fan shall be offset by at least 15 feet (4.6 m) from the nearest side of the mine opening unless an alternative method of protecting the fan is approved in the ventilation plan. Also, each main mine fan shall be protected by one or more weak walls or explosion doors. This paper presents venting and fan configuration designs which provide a comparable degree of safety for explosion protection. Design flexibility is enhanced and a means for consistency in safety judgements is afforded.

Jan 1, 1993

Introduction Surface mining is a business, and the objective of most businesses is to make as much money as possible within certain responsible constraints. Businesses normally measure their potential to make money by estimating the discounted cash flow rate of return on new projects or the net present value for ongoing projects. These estimators of profitability are calculated using the following well-known equation: [ ] where i is the year, n is the total number of years, A, is the after tax net cash generation in year I, r is the discount rate and NPV is the net present value. In its simplest form, when the value of r makes the NPV equal to zero, the discounted cash flow-rate of return (DCF-ROR) is defined. The maximum economically recoverable reserve is identified at the point where the NPV or DCF-ROR is at a maximum. Depending on the measure used (DCF-ROR or discount rate) for calculating the NPV, the definition of recoverable reserve will be different for exactly the same deposit. Maximization of the measure of profitability and the economically recoverable reserves should not be separated from the mining method and sequence of exploiting the reserve. The surface mining methods may involve multiple-pass development of the resource, mining to the ultimate limit in one pass or a combination of the two methods with backfill. Multiple-pass development When planning a multiple-pass mining operation, it is important to determine the width of pit expansions that are appropriate for a specific situation. Production personnel typically want wide, open work areas where operations can be set up to run at peak efficiency. While this is understandable, the trade-off between highly efficient production operations and an overinvestment in stripping should be carefully weighed. As long as safety is not compromised, a few cents per bank cubic yard increase in operating cost due to lower productivity by working in more confined spaces may well be offset by a decrease in the overall short-term stripping requirements. A mini study on productivity and cost should help quantify this cost before deciding on minimum phasing requirements. The bigger challenge associated with establishing smaller work areas is securing operations and management buy-in to marginally lower productivity when reporting results. When cost reduction is the important management goal and everyone is focusing on unit costs, one sometimes loses sight of the goal of total cost management and, even more importantly, maximum profitability. The first pit should be defined by the first grouping of recoverable mineral that has the highest after-tax unit value and forms a feasible mining unit. The assumed mining of the first pit should be followed by the assumed mining of the second most profitable practical pit or pit expansion. If this process of grouping and sequencing is followed until the profitability approaches zero, the general sequence required to extract the maximum economically recoverable reserve is identified. The curve in Fig. 1 is constructed for a rate of production, R, and a quality management strategy, Q, by calculating the NPV for a series of sequences, with each sequence assuming that the operations are terminated on successively lower profit pits. These values are plotted to form the curve in Fig. 1. If the operation ceases on a pit that has too high of a profit, opportunity is lost, and the NPV is lower than the maximum. The NPV curve peaks and starts to decline before the zero-profit pit is assumed mined. This occurs because the money invested in advanced stripping would have made more money invested at the discount rate than by mining the next pit expansion. Therefore, the maximum economically recoverable reserve is defined by the pit limit corresponding to the maximum NPV. There may be an opportunity to refine the definition of the "ultimate pit" around the maximum-value point. The precise definition of the ultimate pit early in the mine life may or may not be important today, depending on how far off in the future these limits will be reached. By the time an operation must decide on its last increment of economically recoverable reserve. much of the

Jan 1, 2000

By A. Bayer, T. Klopfer

"As a leading global strategy consultancy, Roland Berger Strategy Consultants firmly believe that the issue of sustainability is at the core of every business activity. Thus, strategies to enhance corporate sustainability (CS) are an essential cornerstone in the consultancy's approach to develop and implement new strategic concepts for the clients. In this paper, the authors conclude that innovation is the only solution possible to guarantee growth and welfare gains while achieving sustainable development. More efficient and effective ways are necessary to enable technical and social breakthroughs. To illustrate Roland Berger Strategy Consultants's vision on CS, four selected cases from the basic resources, energy and utilities sectors are presented. They demonstrate that the implementation of a CS strategy does not only refer to CEO spheres and are by no means just a moral justification for current business practices. Rather they show that the decision to opt for these new ways also opens up multiple opportunities."

Jan 1, 2005

By R. F. Harig

Designing an underground nuclear waste repository is a complex process. Although many decisions are involved before the design is complete, the first three--what the target horizon is, what the underground boundary is, and where the entry point will be located--are important because they establish the basis for the entire repository design. Even more important than these decisions, however, is the data on which the decisions are based. Because the current data are limited, an aggressive data gathering program is needed during the next design phase to augment information about the intricate interplay among all facets of the repository design and the geologic medium in which the proposed repository is to be developed. Although unique to modern engineering enterprises, the challenges involved in designing a repository in the unsaturated zone are within current technology and engineering practices.

Jan 1, 1991

By G. C. Van Bever, J. J. Zaluski

Introduction The Surface Mining Control and Reclamation Act (Public Law 9587) (hereinafter the "Act" or "SMCRA") passed by Congress in August 1977 represents a comprehensive federal scheme for controlling surface coal mining and the surface effects of underground mining through permitting requirements, performance guidelines and reclamation planning. While the provisions of the Act have been the subject of numerous legal challenges and court battles over the years, it is difficult to identify a more controversial program within the Act than the provisions for designating lands as unsuitable for surface coal mining operations. The lands unsuitable designation process provides for the acceptance and review of petitions submitted by citizens or organizations seeking to have specified land areas designated unsuitable for all or certain types of surface coal mining activities. In filing these petitions, the interested parties or petitioners are required to make allegations about potential adverse impacts on people or the environment and submit evidence supporting their allegations. In 30 U.S.C. § 1272, Congress provided that "[a]ny person having an interest which is or may be adversely affected shall have the right to petition ... to have an area designated as unsuitable for surface coal mining operations." Under the Act, an area can be designated as unsuitable where the mining operation will (1) be incompatible with existing state or local land use plans, (2) affect fragile or historic lands, (3) affect renewable resource lands where mining operations could result in substantial loss or reduction of long-range productivity, or (4) affect natural hazard lands where such operations could substantially endanger life and property. In enacting SMCRA, Congress mandated that each state establish a process to determine which, if any, lands within the state are unsuitable for all or certain types of surface mining operations. In response to this federal legislation, the Kentucky General Assembly adopted a state regulatory program for surface mining that included provisions direct¬ing the Secretary of the Natural Resources and Environmental Protection Cabinet to establish a program for designating lands as unsuitable for surface mining as required by the Act. In recent litigation in Kentucky, several environmental groups filed a lands unsuitable petition, later joined by the University of Kentucky, challenging a proposal by Arch Mineral Corporation to surface mine over 3 million tons of recoverable coal. The petition sought to designate over 10,000 acres of land adjacent to Arch's proposed operations as unsuitable for surface mining operations, basically alleging that the mining would disturb an outdoor laboratory. The filing of the petition activated Kentucky's regulatory scheme for reviewing lands unsuitable petitions that can result in an absolute prohibition against surface mining on the petitioned land for historical, environmental and other related reasons. The designation process involves vague petition requirements creating a situation that Arch argued is devoid of constitutional due process and subject to abuse by the petitioner on many fronts. Arch maintained that the lands unsuitable regulations do not grant adequate protection to Arch's legitimate property rights under the due process clauses of the United States and Kentucky Constitutions and are thus void and unenforceable. The entire process resulting in a decision on the petition took just under 12 months in the Arch case, and although Arch was ultimately successful in preserving its right to mine, Arch's surface mining permit was held up for this period of time. This delay led to the cessation of mining operations by Arch and the idling of over 250 workers. This paper will review the lands unsuitable designation process and the significant implications the process has for existing surface mining operations, currently proposed operations and even those long-range operations not yet contemplated. Special emphasis will be given to Kentucky's lands unsuitable program. Finally, the recent litigation involving Arch Mineral Corporation and its effort to surface mine 81.5 acres of Arch controlled property will be utilized to illustrate this very unusual regulatory scheme. Regulatory background Chapter 30, Subchapter F of the Code of Federal Regulations (C.F.R.) promulgated to implement the provisions of SMCRA, requires that each state establish procedures under the state's surface mining program for designating non-federal and non-Indian state lands as unsuitable for all or certain types of surface coal mining operations. 30 C.F.R. § 764.1. The C.F.R. establishes minimum standards for state lands unsuitable programs and sets out requirements for filing a Lands Unsuitable Petition (hereinafter "LUP"), processing LUPs, decision-making guidelines and hearing requirements. Kentucky has adopted regulations providing for the implementation of the lands unsuitable process as part of the state's regulatory program under SMCRA. The following discussion summarizes the principle components of the Kentucky lands unsuitable program.

Jan 1, 1993

By Howard L. Hartman

To concede that I am the most surprised - not to mention the least likely - recipient of the Daniel C. Jackling Award is a true confession I must share with you. Quite honestly, I've asked myself, "Why me?" The Jackling Award has a well-deserved reputation of being a practitioner's, a doer's, a CEO's award - not kudos for a retired school teacher! While at least five of the previous recipients have taught in universities, to my knowledge I am the first to earn the award for "alleged" academic accomplishments. It is humbling enough to keep me livable for a long time. If you glance over the roster of Jackling Award lecture topics, you will spot another anomaly: The lectures last year and this deal with the subject of education - the only two in the 37-year history of the award. The two complement one another rather well, too, C. Allen Bom of Amax addressing critical needs of public education, while I am going to look at the post-high-school years. But I want to focus on more than engineering education. The training role of industry - the principal consumer of our product-also warrants examination. As I hope to establish, there is something unique about mining engineering - education and practice - that is both strength and weakness. We need to recognize that, if we are to cope with the weaknesses in order to capitalize on the strengths. We look at five premises that relate to the uniqueness of the mining engineer and his or her preparation for a professional career.

Jan 1, 1991

By A. T. Weber, G. T. Adel

Earlier studies on the hydrodynamic interactions between fine particles and air bubbles have shown that fine particle flotation can be improved by using small air bubbles. In the present work, microbubbles ranging in size from 70 to 250 microns have been used in a flotation column for the processing of fine coal. The performance of the microbubble column has been studied as a function of wash water addition rate, aeration rate, feed rate and column length to diameter (L/D) ratio. The information collected from these tests has been used to analyze column behavior and to develop scale-up criteria. The results of this investigation suggest that mixing within the column may not be as significant as bubble size and residence time in determining column performance. Improved recovery can be obtained by decreasing bubble size which increases the flotation rate constant, and also by increasing L/D which increases residence time for a fixed column volume. The increase in residence time with L/D is due to a decrease in the volumetric flow rate of wash water with column diameter.

Jan 1, 1988

By M. E. Lewellyn

A lower moisture content for a clean coal product means increased Btu content, or increased yields at the same Btu content, and lower operating costs. The conventional surfactant-based dewatering aids effeciently lower the moisture content but often the presence of residual surfactant in the filtrate and recycle water causes problems downstream. ACCOAL-DRI 1000, a surfactant-based dewatering aid, was developed to solve this problem by minimizing the downstream effects while efficiently lowering the moisture content. The theory of the use of surfactants in filtration will be discussed as well as the development and field evaluation of this new product.

Jan 1, 1988

By Marie-Josée Banwell, Cyriac Sebastian, Giacomo Falorni, Sara Del Conte

Interferometric Synthetic Aperture Radar (InSAR) is a satellite-based monitoring technique that complements other in-situ methods for detecting and measuring surface displacement. Recent advances in data processing algorithms, coupled with the use of high-resolution satellite systems, make it possible to now provide high-frequency InSAR monitoring services, with updated results delivered every time a new satellite image is acquired. The advent of large, continuously updated data sets, however, brings new challenges, including the need to rapidly sift through the data to identify only those points showing relevant ground displacement information. This has been achieved by using trend variation analysis tools, that quickly isolate and highlight only areas of anomalous behavior. The paper focuses on project case studies where continuous InSAR monitoring has proven to be key in identifying displacement trend changes near tunnel alignments.

Jun 13, 2021