Search Documents

By James F. Albus, Vincent C. Grimshaw

High pressure fluid energy grinding, or jet milling, is a versatile method of continuously fracturing solids into fine particles to gain substantial increases in exposed surface area Applications in industrial minerals grinding include calcium carbonate, talc, barytes, mica, diatomaceous earth, bauxite, rutile, coal, kaolin, sepiolite, diamonds, etc The basic principles can be extended to provide continuous drying and delivery of discrete par¬ticles from a wet process slurry The main design and operational features of jet mills and dryers are described, relating energy consumption for both air and steam milling and hot air drying techniques Mean particle sizes in the order of 1 micron are achievable from pre-milled feeds, or maintained from similar slurries in the drying mode Aspects of feed preparation and multi-stage processing are discussed

Jan 1, 1983

At present the feasibility of developing underground facilities for the storage of a number of products including toxic waste, oil, nuclear waste and low pressure gas is under investigation in e number of countries. A possible method of storage is in large excavations, Preliminary ventilation design work has identified that the climatic conditions encountered within these large excavations are a limiting ventilation pollutant within the ventilation system. This paper examines the design of a variety of sizes of excavation from a ventilation viewpoint. The main phases of an excavations lifetime can be divided into four main phases, these being construction, civil and mechanical fitting, storage, full and sealed. The paper details ventilation design options for the first two phases of e vaults lifetime, giving climatic simulations to assess the likely climatic conditions within the excavations for e number of facility depths. The options for climatic control are given and analyzed by means of climatic simulations techniques. l. INTRODUCTION The feasibility of developing underground facilities for the storage of a number of products is under investigation at present in a number of countries. This paper details a possible design for such a facility where the product is to be stored in large underground excavations. A facility layout has been designed with the aim of allowing concurrent construction and storage operations. Thus from a ventilation perspective the facility consists of two circuits , a construction ventilation circuit and a product ventilation circuit both of which are served by an intake and a return surface connection The construction and storage circuits are considered as independent of each other , any interaction in the form of leakage must be from the construction to the storage circuit. From the facility design a ventilation network was developed to assess the ventilation requirements of the facility. In analyzing the pollutant loads for the construction circuit two pollutants were recognised to be critical to the ventilation design , these being diesel exhaust fumes and heat end humidity. In this paper ventilation design options for the construction and civil and mechanical fitting phases of the excavations are analyzed by means of climatic simulation and options for climatic control within the vaults are outlined . 2. FACILITY DESIGN A schematic diagram of a facility design is illustrated in Figure 1. There would be two distinct ventilation circuits , one to service the construction operations and the second to serve the storage operations which occur concurrently with construction , the circuits are separated by ventilation bulkheads . Access to the facility for intake air is provided by two drifts, one to serve each circuit. Two shafts act as returns to surface. The facility consists of two distinct zones for the storage of two types of product. One type is to be stored in smell linear excavations. The second zone is for the storage of a second product in larger excavations. The maximum cross-sectional area and perimeter for the smell linear excavations are 456.25 m2 and 83.2 m, while for the larger excavations they are 440.1 m2 and 86.4 m. Excavation construction consists of three phases: 1. Initial pilot tunnel development between main intake and return to provide through flow ventilation. 2. Enlargement to produce the required finished cross-section. 3. Civil and mechanical engineering work to fit out the excavation ready for storage. It is proposed to excavate the excavations using drill and blest methods utilising diesel equipment. Spoil is to be transported to surface by a conveyor belt system. At any one time the maximum number of working places requiring ventilation will consist of ; 3 storage sites, 2 excavations under construction, 2 excavations undergoing civil and mechanical fitting. [ ]

Jan 1, 1993

By Richard J. Adams

Coal jigs have played a predominant role in U. S. coal preparation for fifty years. Recently, an improved fine coal jig has been used to prepare the middle size range coal. These efficient machines are changing the historical thinking about jigs and is consistent with trends in coal preparation throughout the world. The performance achieved and operating cost savings are causing a change in fine coal cleaning strategy. With the exception of a handful of operators, fine coal jigs are generally not well understood by the industry. The objective of this paper is to provide some insight into the past use of fine coal jigs and their potential in the future. Improved Fine Coal Jig Since the mid 701s, an improved fine coal jig has been employed to an important niche in preparation, the 19 mm x 100 M range of cleaning. Several factors due to mining and liberation considerations have caused an expansion of this middle range of coal resulting in a host of challenges for coal preparation engineers. Fine coal jigs have been commissioned in several installations in North America to handle these important applications as shown in Table No. 1.

Jan 1, 1988

By X. Wu, M. Karfakis, E. Topuz

The generalized ventilation network problems encompassing both natural and controlled splitting networks, is formulated using a nonlinear nonconvex programming model, which has not yet been solved satisfactorily. This paper presents a methodology which can deal with the problem. The proposed methodology converts the nonlinear problem into a linear problem, by using special ordered sets of variables, and optimizes it by a modified branch and bound technique. The global optimality of the methodology and its applicability to different cases are investigated

Jan 1, 1991

Bigger is indeed better in today's surface mining operations. That is especially true regarding haul trucks. Building larger, "supersize" trucks, however, means designing more powerful engines and drive systems that are also more efficient and environmentally friendly. And miners are demanding that these trucks have longer service lives with minimum maintenance. So truck makers are teaming with engine manufacturers and mining customers to design these larger trucks that will ultimately lead to reduced mining costs. About 180 of those truck makers, engine designers and miners gathered in Tucson, AZ in September to discuss the state of haul trucks in today's mining environment. Haulage 2000 was sponsored by World Mining Equipment and attracted attendees from around the world. Manufacturers described the latest in haul truck advancements. These included the design of more powerful engines, improvements to mechanical and ac and dc drive systems and suggestions on how to reduce maintenance spending. Technology improvements in tires for larger struck was discussed as was the cost efficiency of new, lighter-weight bed liners. The following is a summary of a handful of the presentations.

Jan 1, 1997

By Rush H. Spedden

Antoine M. Gaudin was a vigorously creative man and throughout his career an internationally respected leader of his chosen profession of mineral engineering. To his professional colleagues and clients and to his former students he was both "Professor Gaudin," their wise, inspiring, and enthusiastic teacher, and "Tony," their warm and beloved personal friend. Thus, his teachings and his unique inquisitive-creative approach to problems live on and grow in the accomplishments of his students. Antoine Gaudin was born at the turn of the century in Smyrna, Turkey, where his father was general manager of a French-owned railroad. It was there that he spent his earliest years, literally in the shadow of classic marbles from diggings at the site of Aphrodesias, which his father had rediscovered. From this, Tony developed an appreciation of the arts. He eventually surrounded himself with art treasures; he reveled in the beauties of nature, and he cherished his choice collection of rhododendron and azaleas. His artistic traits led him to take up painting when his daughter, Elinor, sought his help in blending her tints for a water color. In typical fashion he was not satisfied until he had become adept with pastels in capturing the muted tones of distant landscapes and the technical properties of light and color. Unfortunately not many paintings were produced. His paternal grandfather was Marc-Antoine Gaudin, for many years secretary of the Academie des Sciences in Paris, and a well known chemist and mineralogist whose primary interests included the synthesis of precious stones. In an autobiographical sketch written in 1939, Dr. Gaudin recalled: "As a child I saw many of the original synthetic sapphires and rubies which my father had inherited. This, coupled with my father's avocation of mining ventures and archaeology, early decided that I would become connected with the mineral industry." One can speculate that the archeological activities of his father, the mineral systhesis experiments of his grandfather, and his own early studies of mineralogy and geology formed a base from which his special talents as an experimentalist were to develop. Laboratory research under Professor Gaudin's personal guidance was often an intensive, fast- moving, and exciting experience--especially to a new graduate student. First of all, Professor Gaudin was a highly skilled observer with seem-

Jan 1, 1976

By Gill G. Geesey, Michael R. Hankins, Paul L. Wichlacz, Anita Gianotto, John G. Jolley, Randy B. Wright

Thin films of copper [2.0 nm on germanium internal reflection elements (IREs) and 3.4 nm on germanium discs] were exposed to 10% gum arabic (aqueous solution) , 2% alginic acid (aqueous solution), 1% bacterial culture supernatant (BCS, simulated seawater solution) and 0.5% Pseudomonas atlantica exopolymer (simulated seawater solution). The IRES were monitored in situ, in real time using fourier transform infrared/cylindrical internal reflection/attenuated total reflection spectroscopy as a function of time at ambient conditions. The discs were characterized (pre- and post-exposure) by X-ray photoelectron and Auger electron spectroscopies. Ancillary graphite furnace atomic absorption spectroscopy was used to monitor the removal process of the copper thin film from the germanium substrates. Results indicate that Cu was oxidized by gum arabic, alginic acid and BCS. Furthermore, Cu was removed from the Cu/Ge interface by all four polymers. The Cu was found associated with the polymer solutions.

Jan 1, 1989

"Foreword by Ren BryceSenior engineer, Freeport-McMoRan, Oro Valley, AZ, USAThe eighth annual Mineral & Metallurgical Processing Division (MPD) student poster contest was held in February at the national SME Annual Conference & Expo in Denver, CO. A total of 33 students presented their work at the poster competition. The competition started in January when the students submitted a one-page abstract for judging. In February, they prepared and presented a poster that explained their research. A panel of judges went to each student and listened as the students explained their research in five minutes.The students worked hard at their research and then set aside time to complete all the necessary steps to enter the competition. The MPD recognizes the effort required to enter and as a result, provides monetary rewards to all participants. The first-place winner receives $1,000; the second, $500; the third, $250; and the fourth through seventh, $200. All remaining students receive $100. All of the students also receive a complimentary ticket to the MPD Luncheon. As in past years, there are separate levels of competition for undergraduates and graduates.Graduate winnersKaustubh Shrimali won first place for researching “The influence of starch in amine adsorption by quartz in the reverse flotation of iron ore.” Venkata Atluri received second for studying “The effect of polysaccharides on bubble attachment at talc surfaces.” Jennifer Galvin placed third for investigating “A novel approach to alkali pug bake for the extraction of rare earth elements from monazite concentrate.” In the fourth through seventh places were Amy Richins, Sumedh Gostu, Brett Carlson and Chris Vass.Undergraduate winnersNestor Santa earned first place for exploring “Copper recovery from waste printed circuit boards.” Cassidy O’Connell received second place for conducting “Performance analysis of CMC in high talc copper sulfide flotation systems.” Catalina Vanegas won third place for examining “Cyanidation tests and pretreatments to recover gold from a refractory ore in Colombia.” Kylie Boyce, Michael Archambo and Pritam Sinha were in the fourth through sixth places.Everyone benefits from attending the student poster competition. The students are able to display their work to future employers, and industry professionals can talk to up-and-coming engineers. Next year, there will be another competition for more posters and networking. Come and enjoy the event and the posters."

Jan 1, 2017

By John Greenhalgh, Benoit De Rivaz

"1.INTRODUCTIONThis paper is based on the Lee Tunnel project, which is part of the Thames Water’s Tideway Project.The client Thames Water has employed a Joint Venture of Morgan Sindall/Vinci Grand Projets and Bachy Soletanche to undertake the design and construction of the project under the management of CH2M Hill at a value in excess of £635 million ($990 million). The 3 main elements of the tunnel project are the permanent lining to the shafts, the precast segmental lining, and the secondary tunnel lining. All 3 are reinforced with different types of Dramix steel wire fibers and each element will be described in this paper. This paper will explain the basic structural design of FRC (Fiber reinforced concrete) based on the post cracking residual strength and will describe all the steps of this project, the testing program realized to support innovative design and the main technical learning point. 2.BASIC CONCEPT OF STRUCTURAL DESIGN OF FRCStructural design of FRC elements is based on the post-cracking residual strength provided by fiberreinforcement. Other cases, like early age crack-control or fire resistance, are considered non-structural use of FRC. For structural use, a minimum mechanical performance of FRC must be guaranteed. Fibers can be used to improve the behavior at SLS (Service Limit State) since they can reduce crack spacing and crack width, thereby improving durability and they can be used to improve the behavior at ULS (Ultimate Limit State) where they can partially or totally substitute conventional reinforcement in most conditions. In the design process, the definition of the performance expected from the material is a key factor and the mix-design of the material has to be optimized for the required structural performance.2.1 Testing Method In order to ascertain the structural requirements requested for the FRC segments, preliminary testing on samples will be required and the effectiveness of the proposed solution will also be assured by the testing of full scale specimens. Structural design of FRC elements is based on the post-cracking residual strength provided by fiber reinforcement. For structural use, a minimum mechanical performance of FRC must be guaranteed. Nominal values of the material properties can be determined by performing a 3-point bending test on a notched beam according to EN14651 (figure 1) or by performing the ASTM C1609 beam test:"

Jan 1, 2016

By Euler De Souza, Jason Chew, Aldrich Philip Dirige

Sillmats are structural elements upon which the safety and economics of underfill mining or sill pillar recovery in stopes of moderate width with steeply dipping ore zones, depend. The traditional stability design of cemented sillmats appears to have developed from experience and from standard static physical model tests such as uniaxial and triaxial compression. Such standard static physical model testing approach arrives at some approximate parameters, normally used to describe or predict the behaviour of sillmats in analytical or numerical models. This approach offers inherent limitations and generally results in conservative designs. Centrifuge modeling studies are combined with numerical modeling in this paper to provide insights into sillmat strength behaviour. The results of both modeling techniques suggest that, in stopes with smooth rock wall conditions, sillmat failure is driven by the fill self-weight and has minimum dependency on the fill binder content. In stopes with rough rock wall conditions, however, the wall roughness contributes significantly to the stability of the sillmat during underfill mining. This study indicates that the stability of paste fill sillmats can be designed with confidence using centrifuge physical modeling in combination with numerical modeling.

Jan 1, 2001

By Sadatoshi Ohmori, Karen Shinoda, Nobuharu Isago

Method of tunnel excavation is generally classified such as full-face excavation, bench-cut excavation, diaphragm with center pillar excavation, center drift advancing excavation and so on. These excavation methods should be selected properly in terms of ground condition, the area of tunnel section, the arrangement of construction. Center drift advancing excavation method in mountain tunnel construction, is often applied under quite weak ground condition, prior to the main tunnel widening excavation. Recently, the advancing drift is for the excavation of extreme larger section in main tunnel to confirm the stability of face. In addition, we make advancing deformation occur in drift when the construction was done in poor ground like squeezing and swelling ground, and the force occurred in main tunnel was expected to reduce by the effect of ‘dodging’ for support structure. Mechanical relation between drift and main tunnel has been mainly grasped on past experiences in Japan. However, the characteristic of tunnel enlargement was partially discussed by using the three dimensional analysis and the result was grasped by past experiences on the basis of each tunnel construction. It is considered that the natural ground stress is normally released as the advance displacement, but it was released after the main tunnel widening, causing a displacement and deformation increase. Up to now, the construction practice has shown the reduced displacement during the main tunnel widening excavation by the drift, and the numerical analysis agreed with above observation. However, there is no report found that the displacement and deformation at the time of widening excavation of the main tunnel become larger in case of a drift application. In Kyusyu area, western part of Japan, the northern part of Yoshinomoto tunnel was applied an advancing bench-cutting method for a center drift for the purpose of obtaining the geological information for support selection of the main tunnel in widening excavation. The shape of center drift was a perfect circle with a diameter of 4.0 m or 6.0 m and the same temporary support regardless of the geological situation. As a result, the displacement and deformation of the main tunnel after widening excavation were larger than the section where the center drift was not applied. Furthermore, the displacement and deformation of the main tunnel after its widening excavation was considered larger in the section where the cross-section of the center drift with 4.0 m diameter was applied than one with 6.0 m. Therefore, the center drift with a high rigidity support structure had the effect of suppressing the advancing deformation prior to the main tunnel widening excavation.

Jun 13, 2021

By David A. Roberts, Edward J. Cording, James W. Mahar, Robert A. Robinson, Noppadol Phienweja, Harvey W. Parker

Horizontal inclinometer and deflectometer casings were used to measure deformations up to 15.2 m (50 ft) ahead of and adjacent to the heading in highly fractured and sheared shales at the Stillwater Tunnel. The measurements were compared with borehole extensometer and tape extensometer deformations to evaluate ground movements in advance of, adjacent to, and behind an advancing tunnel heading. Ground deformations of up to 127 mm (5 in.) occurred during passage of the innovative "walking blade-gripper" TBM. Deformations were compared with curvometer/distometer and vibrating wire strain gage data from steel ribs to assess rock-support interaction.

Jan 1, 1985

By D. H. Lynch

This paper is a general description of current Central Florida phosphate mining, beneficiation and product transportation. It is directed and believed to be of interest to engineers not familiar with this industry.

Jan 1, 1978

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

INTRODUCTION The majority of ground water flow models have been developed for large computer systems. Most of these operate under a batch mode of operation, that is, the data are input with a deck of punched cards. The advent of micro- and minicomputers over the last few years opens the possibility of adapting many of these large flow programs to the smaller computers. In general, this adaptation will require more computer time to run the program, but in many cases if the small computer is in-house, the overall cost may be less than that required for a large computer. There are also a number of peripheral devices that can be used to make the data input much easier. As an example, the use of a digitizer with a finite element or finite difference mesh reduces the data input time considerably; the use of a graphics terminal for display of the mesh immediately after it is developed shows immediately whether there are errors in the location of node points. DEVELOPMENT OF AN INTERACTIVE SYSTEM The finite element program, UNSAT2, has been used over the past several years by the authors for several ground water flow problems (Bloomsburg, 1977; Bloomsburg and Wells, 1978; Zahl and Bloomsburg, 1980). In the past these programs have been run on an IBM 370/ 145 computer under the batch mode of operation. One difficulty that has been encountered has been in determining the length of time step that must be specified for operation of the program. The problem is that if the time steps are too large, the program becomes un- stable and operation ceases. If this happens in the middle of the problem, the only alternative is to reduce the length of time step and repeat the entire run. This problem has been alleviated in other pro- grams by using a subroutine that determines the time step automatically. If the solution becomes unstable, the time step is reduced automatically and that portion of the solution is repeated. With an interactive system this can be done by storing the output pressures and restarting the program with the new output pressures. Under the batch mode of operation, there is an option in UNSAT2 that allows restarting of the program from the last point of solution, but this must be specified when originally starting the program. The interactive computer system that we use currently consists of a PDP 1 1 /23 with hard disk drive, CRT terminal, plotter, graphics terminal, digitizer, and printer. The computer has 256 K bytes of core storage and the hard disk drive will accept a 5.2 M byte disk. To run a large program on a computer such as this, some overlaying must occur; that is, subroutines are stored on disk and put into core storage only when they are actually needed for running the program. UNSAT2 required very few changes to run on this computer but some changes were necessary to take advantage of the interactive capabilities of the system. One of these changes consists of the development of a program called DBUILD to build the data file for running the program. This program calls for each piece of data by prompt statement and gives instructions for using the digitizer. The data are then entered in completely unformated form. The node points must be entered in order and the coordinates are determined automatically by the digitizer. The pressure readings or initial conditions on each node point are entered through the terminal. All element information also is entered through the terminal. After DBUILD is run the mesh may be displayed immediately on the graphics scope whereupon any error in node point

Jan 1, 1986

By R. V. Ramani, R. Natarajan, A. Bhattacherjee

Industries in general, and mining in particular, have become safer than ever before. However, there is a need to increase the search for the causes of mining work-related injuries and to contribute to their reduction, as required, through job redesign, work procedures and worker training. Mine accident and hazard control must be practiced in a manner consistent with the overall objectives of the mine management, which include the optimum allocation and effective utilization of the resources. The purposes of this paper are to: • present a set of analytical tools to analyze injury experience data. • apply these tools on a case study example, • discuss the results of the case study, and • identify the application limitations and the future research needs.

Jan 1, 1993

By Ali Hafiz, Aidin Golrokh, Tom Iseley, Kaz Tabrizi, Saleh Behbahani

In the USA many highway tunnels were built during the 1930s through 1960s. This indicates that these tunnels have exceeded their intended design service life. Based on the initial tunnel inventory conducted jointly by the Federal Highway Administration (FHWA) and the Federal Transit Administration (FTA), more than 526 highway tunnels have been identified in the USA. For understanding the condition of the tunnels and risks associated with deteriorating conditions, comprehensive condition assessments are necessary to mitigate risk and remediate works as required. Monitoring the condition and rate of deterioration of tunnels is vital for timely tunnel maintenance and rehabilitation to avoid sudden tunnel collapse. This session will explain the necessary steps for tunnel inspection and review some of the state of the practice information on tunnel inspection techniques.

Jun 13, 2023

By Deepak Malhotra, Robert Dorfler

Modern engineering mill design has been refined over the years to the point where detailed ore and process specification criteria can be developed In the engineering design phase of the project. The plant Is then built to the detailed criteria and performance acceptance tested by the owner to see if the as-built mill meets the criteria, This performance testing is critical to the owner; the test must be systematic with sample collection coordinated throughout the plant. Despite the availability of systematic approaches to plant development, the new plants often fall short of design criteria. This paper discusses the key Issues a Project Manager/Process Engineer should Implement to ensure that plants meet design criteria.

Jan 1, 1991

By R. M. Campoy

In this review of the copper, lead, zinc, and molybdenum industries in Mexico, the author describes how the country's position in the world base metals market and the climate for foreign investment in Mexico have been affected by the nationalization of the banking industry in that country and by recent mining legislation and the current national debt crisis.

Jan 1, 1988

By Don L. Jensen

With the successful implementation of supervisory control on the Bagdad concentrator grinding circuits, steps have been taken to expand supervisory control to the flotation circuits. This paper discusses the design and installation of the slurry delivery systems, analyzing instruments, level control devices, reagent pumps and supervisory software. Emphasis is placed on the design and installation of a reliable slurry transport system to feed the Courier 30 online analyzing instruments. Total system availability has been measured at plus 95%. Phase 1 acceptance testing of the supervisory software indicates a notable increase in copper recovery with no significant change in final copper grade.

Jan 1, 1999

By S. K. Kawatra, M. T. Rusesky, T. C. Eisele

An on-line monitoring system for apparent slurry viscosity has been developed at Michigan Technological University. It utilizes a vibrating sphere viscometer in conjunction with a special slurry presentation system to reduce particle settling and turbulence effects. It has proven to give accurate, reproducible results in an on-line hydrocyclone installation. Its performance shows that it can be an effective instrument on an industrial scale, particularly in grinding circuits. Development of the sensor and the importance of rheology in grinding are also discussed.

Jan 1, 1992