Search Documents

By Alan Bye, Megan Little

Geology, and the detailed understanding of its properties, are fundamental to the optimal design and successful operation of any mine. To that end extensive fieldwork has been conducted at Anglo Platinum?s PPRust operation to collect geotechnical information both from exploration boreholes and in-pit mining faces. Since 1998, geotechnical data has been collected from over 337 km of exploration core, 7 km of exposed mining faces and more than 15 600 field and laboratory tests, in order to define the complete set of geotechnical properties for each rock type in the mining area. The geotechnical information collected is stored in two databases, SABLE Warehouse and MineMapper3D before it is imported into the Datamine mining software package. The geotechnical parameters, mining rock mass rating system (MRMR), uniaxial compressive strength (UCS), fracture frequency per metre (FF) and rock quality designation (RQD), are modelled using geostatistics to generate a 3D geotechnical block model. Data is interpolated between exploration boreholes and exposed mining faces and modelling is constrained, using wireframes, by rock type and structural features. By having detailed geotechnical information available in a 3D model that can be readily accessed and interpreted, significant production optimisations, feasibility studies and planning initiatives can be implemented. From a slope design perspective the model is used to target data deficient zones and highlight potentially weak rock mass areas. As this can be viewed in 3D, the open pit slopes can then be designed to accommodate the poor quality area before it is excavated. It also follows that geotechnical zones can be readily identified and the slopes optimised accordingly. Rather than viewing the drill and blast department as an isolated cost centre and focussing on minimising drill and blast costs, the fragmentation requirements of the comminution and load and haul business areas are studied. It is well understood that chemical energy is the cheapest form of comminution and that major downstream benefits can be derived by increasing drill and blast expenditure. 238 blasts were assessed to determine the optimum fragmentation requirements for ore and waste. Based on the study a mean fragmentation target of 150 mm was set for delivery to the crushing circuit and a mean fragmentation of 230 mm was set for waste loading from the pit. Substantial benefits have been realised in the drill and blast department by developing empirical correlations that relate the MRMR values in the geotechnical model to a blastability index, fragmentation, required powder factor and costs. As the geotechnical model can predict changes in geotechnical conditions, the blasting

Jan 1, 2007

By M. K. Elmouttie, G. V. Poropat

The analysis of structure using joint set statistics is well known. Other data such as the position of discontinuities and the contacts between rock mass units cannot be easily incorporated in simple statistical analysis based on orientation alone. Algorithms to model the structure of rock slopes using measurements of the orientation and position of discontinuities are being developed by CSIRO Exploration and Mining. These algorithms provide a capability to model the structure of a rock slope and estimate the likelihood of the formation of hazardous blocks in existing or proposed rock slopes and identification of the location and size of these blocks. The algorithms provide the basis of structural modelling to identify potential failure mechanisms in rock slopes.

Jan 1, 2006

By A. B. Fox, R. P. Thackray, K. C. Mills

The role of mould fluxes in continuous casting is reviewed. The main functions of the flux are described and the importance of the flux in providing lubrication and the right level of heat transfer between the shell and the mould is described. The major problems of longitudinal, transverse and star cracking, gas and slag entrapment and deep oscillation marks in the steel product and ?sticker breakouts? are analysed. The important physical properties of the flux in combating these various problems are identified. Physical property data for the fluxes are given.

Jan 1, 2004

By P. Gonzalez, C. Ariyo, L. Holappa

Oxidation state of titanium was determined in CaO-SiO2-TiOxslags in the composition range25–53 per cent CaO, 27–46 per cent SiO2, 10–55 per cent TiOxat 1873K using gas equilibration method. In the experiments, slags with different titanium oxide contents were equilibrated with a known carbon monoxide and carbon dioxide ratio. The results were used to determine the Ti3+and Ti4+contents as well as the activity coefficient ratio of corresponding oxides in the slag. The dependency of the activity coefficient ratio as a function of oxygen partial pressure was determined. Keywords: titanium, titanium oxide, activity, activity coefficient, slag iron, carbon monoxide,carbon doixide, gas, equilibrium.

Jan 1, 2004

By J. M. Lottering

Paper written on project work carried out in partial fulfilment of B Eng (Chem) degree Operational factors influencing the electrostatic separation of mineral sands were investigated in a laboratory separator. Measurements were collected online by means of an optical sensor using diffused reflectance spectroscopy to determine the mineralogical composition. The results have shown that the roll speed and potential were the dominant operating variables, collectively explaining more than 83% and 68% of the product grade and yield, respectively. In contrast, the feed rate, temperature and position of the plate did not affect separation. The effect of the ambient relative humidity, ranging from 10% to 45%, could not be assessed conclusively and at best appeared to have a weakly beneficial effect on the product grade. Keywords: process modelling, high tension roll separator, mineral sands

Jan 1, 2006

By A. Hiltunen, R. Hiltunen

The utilization of blast furnace and BOF slags has long traditions and well-known applications in the building and road construction industries and in soil conditioning. The starting point for product development has been the basic physico-chemical properties of slags. This development has led to the almost 100% utilization of blast furnace slags and also considerable amounts of steel slags. While new methods and applications are continuously being looked for and developed in order to recycle and utilize all types of slag, there is at the same time an increasing debate over the exact nature of the slags, whether they are products or waste material, and whether they should be considered substances or preparations. These questions have emerged as a consequence of the environmental effects of the slags and current environmental legislation. The environmental effects of slags can be seen to be both beneficial and less beneficial. There is no doubt about their benefits in the road construction industry, as they allow significant savings in terms of natural materials and in transportation. It is also a known fact that using slags as fertilizers and in the cement industry leads to reduction in CO2emissions. The less favourable effects are the possible harmful emissions into the soil and groundwater. In this paper we describe the properties of slag products and their environmental effects according to investigations carried out in Finland. Keywords: utilization, blast furnace slag, steel slag, properties, solubility, environment

Jan 1, 2004

By J. Ekengård, H. Srinath, M. Andersson, P. Jönsson, D. S. Sarma

The present paper deals with mixing between the metal and slag phase during the ladle refining process, including vacuum degassing. Dispersion of metal drops in ladle slags has been studied. The results show a larger quantity of metal droplets in ladle slag during the alloying and stirring phase than during the subsequent vacuum degassing phase. The thermodynamic and kinetic aspects of the interaction between metal drops and the slag matrix have been considered and probable reasons for the observed distribution discussed.

Jan 1, 2004

By J. Drzewiecki, J. Kabiesz

Coal mining using longwall methods of mining can lead to intense disturbances of undermined roof strata. The disturbances may extend beyond the extraction area and the resulted rock mass deformations will appear differentiated. In the case of stiff and undermined roof strata, the energy stored in these rock masses may be frequently dissipated in the form of high-energy seismic tremors. Such events can occur if these strata should fail or „free themselves” either from the constrainment of rock environment or from adjacent strata. It has also been found that the amount of the stored energy closely depends on the size and/or slenderness of these strata. Thus, it would be possible to apply specific preventive measures to reduce the energy of mining – induced seismic tremors. The methods are based on artificial disintegration of the structure of energy – storing strata. One of the most efficient methods is a method of directional hydraulic fracturing, which is regarded as an alternative solution from the traditional blasting and hydraulic methods.

Jan 1, 2003

Council for 2005/2006 President W.H. van Niekerk President-elect R.P.H. Willis Vice-presidents Senior R.G.B. Pickering Junior A.M. Garbers-Craig Immediate Past-president F.M.G. Egerton Honorary Treasurer J.A. Cruise

Jan 1, 2006

By I. A. Minaev

The conditions of a stability of metallurgical films on a surface of solid on the basis of classical regularities of a thermodynamics are considered. For specific conditions of metallurgical processes the basic equations relevant to non-metallic inclusions (product of steel killing) migration and transfer through the interface boundary of metal-slag are obtained. The basic criteria equations of conditions of stability of metallurgical dispersed systems are developed in view of films formation. The probable thermodynamics reason of wetting due to formation of stable films are discussed. The experimental measurement of thin and thick films elastic resistance for metallurgical systems are carried out and the results are discussed. The presence of a wetting thick film increases stability of dispersed systems (facilitates an inverse implication of non-metallic inclusion in a melt) due to a barrier effect of wetting films. The quantitative evaluations of non-metal inclusion stability for steel in contact with any metallurgical slag are carried out. The results are in accordance with technological experience. Keywords: Inclusion removal, Film thermodynamic, Slag-metal dispers system

Jan 1, 2004

By C. Maree

Paper written on project work carried out in partial fulfilment of B. Eng (Chem. Eng.) This paper describes the development and use of a process simulator to optimize gypsum recovery at Afmine, a small plant near Yzerfontein on the South African West Coast. The simulator consisted of models of the major plant equipment, viz. hydrocyclones, surge bins, settling tanks, a primary sieve and a dewatering screen. Experimental data suggested that the equipment could be modelled satisfactorily from data published in the open literature. Simulation studies have indicated that gypsum losses on the plant could be reduced substantially by means of some relatively minor modifications to the plant layout. Moreover, sensitivity analyses of the plant have indicated that optimization of the settling tanks should receive priority over the other process units.

Jan 1, 2005

By L. Chen, G. A. Brooks, S. A. Nightingale

The dissolution of alumina and magnesia has been investigated using laser scanning confocal microscopy (alumina) and a rotating finger apparatus (magnesia) to assess the effects of temperature, composition and forced convection on the rate of dissolution in CaO-SiO2-Al2O3based slags. The two techniques have differing strengths and limitations, and provide complementary methods for studying dissolution. Alumina dissolution was studied for temperatures from 1477 to 1577°C. Based upon the data, the rate controlling mechanism was thought to be mass transfer control in the slag. The diffusion coefficients for the alumina particles are estimated to be in the range 10-11to 10-10m2.s. MgO degradation for sample rotation speeds of 50 to 800 rpm at 1500 and 1530°C was studied for both congruent and incongruent dissolution. The results show that the rate of dissolution for this is primarily controlled by a diffusion mass transfer mechanism for congruent dissolution except at the highest rotation speed. For incongruent dissolution, the mechanism is much more complex, with the morphology and distribution of the spinel reaction product having a significant effect. At high speeds and prolonged times, mechanical forces played a major role in the degradation process. Keywords; kinetics, corrosion, refractories, dissolution rate, inclusions, mass transfer, slags, steelmaking

Jan 1, 2004

By L. Li

The performance of microemulsified diesel and conventional diesel collectors in coal flotation was compared by flotation indicators, including combustible recovery, ash content of the clean coal, and the flotation index. An efficient separation with lower dosage was obtained using the microemulsified diesel collector. Under optimum separation conditions, the microemulsion consumption was 100 g/t less compared with diesel. The saving in diesel consumption using the microemulsion reached about 70%, disregarding the consumption of the surfactant and cosurfactant. Frothing tests showed that the frother dosage was decreased by using the microemulsion collector, because of the surfactant and cosurfactant added during preparation. The microemulsified diesel collector is superior to the conventional diesel collector in terms of diesel consumption and separation efficiency, but the selectivity requires further improvement. Keywords froth flotation, microemulsified collector, coal.

Nov 1, 2013

By K. Ding

The thermodynamic activity of MnO was measured in MnO-CaO-MgO-SiO2slags that are typically encountered in the production of manganese containing stainless steels. Gas equilibration-quenching technique was employed in measuring the activities. Activity of Mn in Pt-Mn alloys were redetermined at 1600°C which reconfirmed earlier results of strong negative deviations. MnO activities were then measured by equilibrating slags of various compositions based on a statistical experimental design procedure with Pt-Mn alloys under controlled partial pressure of oxygen in MnO saturated platinum crucibles at 1600°C. Activities of MnO were found to increase with increasing concentration of MnO, basicity and CaO to MgO ratio. Two multi-coefficient repression models were developed to predict the activities and activity coefficients of MnO in slags at 1600°C. Keywords: activity, MnO, slag.

Jan 1, 2004

By W. Stumpf

Mill log analyses and complementary hot deformation studies were carried out on the as-cast structure and on a hot rolled structure of the same low carbon steel (SAE 1006) that had been processed according to the direct or hot charge route in a compact strip plant. The main softening mechanisms during hot rolling were found to be complete dynamic recrystallization during each pass above about 1000°C for the as-cast structure with an austenite grain size of 277µm and, secondly, incomplete static recrystallization after each pass with a finer austenite grain size of about 26 µm and tested below 1000°C. A two-stage hot working mechanism has also been found by others on a similar steel also processed by the hot charge route and this may appear to be a characteristic of this type of material. Constitutive constants determined from hot working studies were combined with other constants from the literature and incorporated into a grain size development model that correctly predicts the final ferrite grain size in the hot rolled strip steel. The predicted incomplete static recrystallization during the last three finishing passes in the plant appears to result in some retained strain in the hot rolled austenite as it transforms to ferrite on the run-out table. Analyses with the model predict relatively little sensitivity of the final ferrite grain size to process and product variables such as temperature and strain per pass for the last three passes and also the starting austenite grain size in the slab. Keywords: Low carbon steel, hot rolling of strip steel, rolling mill log analyses, austenite grain size, ferrite grain size, grain size modelling.

Jan 1, 2003

By X. H. Zhang, J. G. Cai

This paper discusses the behaviour of large-span tunnels and caverns in hard rock in a major underground storage project. In-situ stresses were measured using hydraulic fracturing during site investigation and 3-D overcoring during construction, with both showing a horizontal stress ratio of 2-3 times the vertical stress. Rock reinforcement design was based on the Q-system combined with numerical modelling for special design cases. Tunnel design and performance were checked and monitored by in-situ instrumentation during rock excavation, including measurements of deformation, convergence, and load on rock bolts. Deformation measurements using borehole extensometers included one borehole drilled into the virgin rock before rock excavation, which provided a direct and very insightful comparison with the various deformation measurements made during rock excavation. These measurements coupled with numerical calculations have proven that the high horizontal stresses to be very favourable to the stability of the large openings.

Jan 1, 2003

By J. Björkvall, S. Ångström, L. Kallin

In this paper results from industrial trials of CaC2 injection during stainless steel production in an electric arc furnace at Sandvik Steel is presented. The main purpose of the investigation was to analyse the effect of the injection on slag foaming and final chromium oxide concentration in slag. The results show that both an increase in slag foaming and a decrease of the final chromium oxide could be obtained during the charges with CaC2injection. On the basis of the results, the economical requirements are also discussed. Both the technical and economical requirements could be achieved for steels alloyed with Mo. In order to secure the economical requirements for all steel grades of interest, the injection technology must be further developed. It would also be important to utilize the positive effect of the slag foaming on the electric energy consumption. The work has been performed as a part of MEFOS frame research programme with participants from Sandvik Steel, AKZO Nobel and Avesta Polarit. Keywords: stainless steel, EAF, slag foaming, injection, CaC2

Jan 1, 2004

Colloquium and General Meeting were held at Kelvin House on 19th May, 1971, the theme being 'Modern trends in coal mining practice.' Mr V. C. Robinson (President) was in the Chair. The Colloquium was attended by 205 delegates and was opened by the President at 9 a.m. OBITUARY The President: 'It is my sad duty to announce the death of C. C. Cullen, Fellow, who joined the Institute in 1946 and passed away on 15th March, 1971. As a mark of respect to the memory of the deceased and in sympathy with the bereaved I would ask you all to rise and observe a few moments silence'. ELECTION OF SCRUTINEERS The President: 'In terms of Clause 9.4 of the By-Laws I now call for the nomination of seven Corporate Members to act as scrutineers of the ballot for Council'. Messrs V. C. Robinson, Prof D. D. Howat, Dr J P Hugo, D. G. Maxwell, J. K. E. Douglas, R. J. Adamson and P. Lambooy were nominated by P. W. J. van Rensburg and seconded by P. A. von Wietligh. The President: 'Are there any further nominations? If not I declare these gentlemen elected.' MEMBERSHIP The President: 'I have much pleasure in announcing that the names of candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades: Members: Douglas Edward King, Bryan Rudolph Scott, James Gregor Phimister, Anthony David Walters. Graduates: Cornelius Johann Muller, Marthinus Stephanus Mulder. Associates: John George Everson, Colin Robert Llewellyn Davies. Students: Francois George Enslin Beetge, Ewald Boshoff, Christiaan J. Cloete, Christopher John Davies, Cameron George Elvin, Kenneth Eric Field, Johannes Louis Fourie, Hans Gert Gastrow, Peter John Ledger, James Robert William Lindsay, Kynaston Lloyd McDonald, Richard Peter Mohring, Arthur Leslie Painting, Matthias Arthur Pascall, Ian Neil Sinclair, Donald Allan James Ross-Watt. MEMBERS TRANSFERRED TO A HIGHER GRADE From Member to Fellow: Peter Norman Roberts. From Associate to Graduate: Alfred Eric WaIter Fletcher. From Student to Graduate: Wilfried Pierre de Villiers, Edward Emile Eichenberger, William Alan Nairn, Lodewyk Johannes de Jager, Colin Henry Obray, John Grenig Rees. COLLOQUIUM The President opened the proceedings and introduced Mr N. W. S. Schumann as the overall chairman for the day. The following papers and contributions were presented: FIRST SESSION: Chairman R. C. J. GOODE. Paper: 'Problems encountered in the operation of a new colliery' by P. M. C. Wilson and A. A. Oakes. Contributors: D. J. Moloney, G. R. Canny, I. G. Evans, R. B. MacGillivray, Dr F. G. J. de Jager, M. J. Deats, and N. Zolezzi. R. B. MacGillivray Mr President and gentlemen, I would like to congratulate the authors on presenting a most interesting paper on a very important subject. After several attempts at finding suitable reserves to extend the life of Welgedacht Exploration Company's Utrecht Colliery a block of coal rights was acquired south west of the town of Utrecht. A study of these reserves showed that they would enable a satisfactory return on capital invested to be achieved. It was decided therefore to open up what is now called the Zimbutu section of Welgedacht Exploration Company, to produce 41 000 metric tons of coal per month. The decision to open this section was taken in August, 1968 and due to certain allocation requirements it was necessary to bring it into production by the 1st of January, 1970. Fortunately a fair amount of statistical data had been collected prior to August, 1968 from the old Utrecht Colliery in anticipation of opening a mine and a fairly detailed rechnical report had been prepared. As a result the dead line was only missed by four days. Main features of the Design A feasibility study was carried out on three possible shaft positions and the final position was selected from these three on economic grounds. As the coal seam at the selected shaft position was only 21 metres below the surface it was decided to sink two twin incline shafts to enable rapid establishment of through ventilation and alternative hauling arrangements for quick development. This also allowed the final vertical ventilation shaft to be placed at some distance away to avoid the nuisance of fan noise. Second outlet requirements are also very well met by these twin inclines. Again on the basis of economics and also due to the uncertainty of roof conditions it was decided to use hand loading methods underground. However, to allow for future possible conversion to mechanised loading, should this become economical through rising wages, a conveyor belt was installed in the hauling shaft. This conveyor belt is fed from an endless rope haulage in the east companion by means of tipplers, a bin and a feeder. The main development heading was left clear for the future installation of a conveyor belt which would afford easy conversion to mechanisation.

By Yijun Caoa, Xiuxiang Taoc, Zhongbo Hub, Yinfei Liaoa

A new preparation scheme for a difficult-to-float coking coal from the Kailuan Mine, Tangshan, China was investigated. The results showed that grinding followed by column flotation was beneficial for obtaining products with low ash content. The positive effect of grinding on the coal floatability is attributed to the liberation of intergrowths and coal surface improvement. Tests indicated that 10 minutes was the optimum grinding time, and over grinding resulted in a deterioration in flotation performance. With a grinding time of 10 minutes, conventional flotation had potential to yield a product with around 12.42% ash content and 69.15% combustible recovery. Column flotation can reduce the product ash content to 11.15%and increase combustible recovery to 74.47%. Consistently better flotation results reveal that column flotation is more efficient than conventional flotation for such fines.

Jan 1, 2015

By W. C. Joughin

Problems with the stability and performance of rockpasses in deep-level mines are common. This paper presents the results of an investigation into the recorded performance of rockpasses in deep-level gold mines. Records relevant to the geological environment in which the passes are excavated, their excavation details, and their historical performance are not at all well documented on mines. In general, the quality of data available from mines is poor. The investigation showed that very large spans frequently developed in passes during use, and that rock mass quality, the orientation of the pass with respect to the dip of the strata, and the magnitude of the stress acting normal to the axis of the pass were the main factors of influence. From the historical information obtained, the risks of instability in rockpasses are identified.

Jan 1, 2005