Search Documents

By G. Nino de Guzman, L. C. Woollacott

The isotherms that are usually taken to represent the force 'driving' the adsorption in carbon-in-pulp processes may change from contactor to contactor. This paper reports on an investigation into the extent to which this Isotherm shift is Influenced by the changes in oxygen and cyanide concentration that occur in operating plants. The impact of the isotherm shift on the reliability of simulation results is examined.

Jan 1, 1993

By P. King

In considering the available reserves of coal, the author points to the importance of improved recovery, and defines three extraction ratios: the geological extraction ratio (or exploitation factor), the economic extraction ratio (or mining factor), and the geometrical extraction ratio (or volumetric extraction factor). He discusses the factors affecting each of these ratios, and concludes that, although geological factors cannot be considered in isolation from technical and economic factors, the geological extraction factor is the most significant criterion of whether the best use is being made of coal resources.

Jan 1, 1980

To B. K. Martus I discussed several points raised by Mr Martus in my reply to Professor Krige*. Mr Martus discusses several possible interpretations of optimum South African sales, but in my paper these sales refer to the sales level that maximized the working profit of the whole South African gold-mining industry over the past eleven years. Mr Martus also seems to be under the impression that the paper deals with the future. While there may be references to the future, and some implications for the future may be obvious, the paper deals essentially with the past eleven years.

Jan 1, 1984

Two column flotation cells have been installed as single-stage rougher cleaners at Batu Hijau. The objective was to provide additional residence time in the cleaner circuit to maintain maximum recovery during high mill throughput and high feed grade periods. Installation of the columns has allowed the relatively coarse, well-liberated rougher concentrate and the relatively fine, low-grade scavenger concentrate to be treated separately, improving metallurgical performance in the cleaner circuit. Plant results show that the columns produce a high-grade concentrate at an average stage copper recovery of approximately 80 per cent. There is also indication of increases in both overall plant copper recovery and final concentrate copper grade. In addition, the operability and stability of the cleaner circuit has greatly improved.

Jan 1, 2007

By J. A. L. Napier

An analytical solution to the best choice of cutoff grade for a mine is deduced for an assumed model of selective mining. It is found that this choice is determined by the constancy of a special function, the Hamiltonian, over the life of the mine. It is suggested that the appropriate constant value for this function should be determined by the expected long-term average of the paylimit. In that case, the optimum profile can be calculated at each point in time according to the prevailing working cost and product price. In particular, a decision can be made between operation at the true paylimit or at the subsidized paylimit implied by either the lease and tax formulas or the assistance formula for gold mines. It is also shown how the basic formulation can be extended for 'use in the determination of the optimum joint paylimit for two products over the life of the mine.

Jan 1, 1983

John Keith Elers Douglas recently retired from active participation in the activities of the South African Institute of Mining and Metallurgy after over forty years of diligent and valuable service to the Institute. This account of his contributions to the mineral industry and associated organizations is presented as a tribute to all his hard work and dedication. Mineral processing The Fourteenth International Mineral Processing Congress, sponsored by the Canadian Institute of Mining and Metallurgy, is to be held in Toronto from 22nd to 27th October, 1982. The theme of the meeting is 'Worldwide industrial application of mineral technology'.

Jan 1, 1981

The above paper is an important contribution to the field of physicochemical studies in ferromanganese production. The authors are to be congratulated on the well planned and competently executed experimental work and on the interpretation of the data. Although the paper is essentially descriptive, the results lend themselves to thermodynamic interpretation (but in such a complex system as that studied this cannot be done rigorously), as well as to an examination of the probable reduction mechanisms that operate at various stages.

Jan 1, 1979

By D. J. C. Taylor, R. A. Kruger

Unbridled mining operations can have a serious negative impact on the surroundings. With the recent increased awareness of the need for environmental conservation and the resulting advances in environmental control, the mine planner has new tools at his disposal for the successful implementation of mining projects while avoiding negative environmental effects. This paper discusses the environmental strategies adopted in the planning and commissioning of a trial underground coal mine. The minimization of negative environmental effects is demonstrated and, where applicable, environmental benefits are examined.

Jan 1, 1986

By D. D. Marsden

The paper briefly outlines the history of the successful development of vegetating techniques for mine-residue deposits. It seeks to place on record the major roles played by M.J. Mrost, who initiated and systematically developed the concept, and W.H. Cook, who continued the trials and successfully directed a stupendous large-scale project. The vegetating techniques currently practised are outlined, and it is concluded that vegetating is still the only surface-stabilizing technique of any significance that is employed throughout the world.

Jan 1, 1987

By A. W. de Villiers

This paper explores the behaviour of methane in the goaf during longwall mining, together with some methods for the control of methane emissions into the goaf, the working face, and the ventilation system. Experimental work done at Twistdraai Colliery, Sasol Coal, is referred to, as well as the gas-drainage system being practised at West Cliff Colliery in New South Wales, Australia. Gas drainage is discussed briefly, and certain suggestions are made in regard to coal mining in South Africa.

Jan 1, 1989

By A. Montini, M. H. Moys

A technique for the measurement of slurry consistency inside a grinding mil is described. The rate of slurry drainage from a sensing probe mounted through the mil shell is measured and correlated with the percentage solids of the slurry discharging from the mil. The response time of the measurement(obtained on a pilot bal mil) is compared with the response time of the viscosity of the mill discharge. It is shown that the new measurement should allow much tighter control of the mil behaviour, with concomitant savings in the consumption of power and steel.

Jan 1, 1988

By F. P. A. Robinson, J. W. Fourie

Austenitic stainless steels are welded using low-heat inputs. However, owing to differences in the physical metallurgy of austenitic stainless steels and duplex stainless steels, low-heat inputs should be avoided for duplex stainless steels. This paper highlights the differences in solidification mode and transformation characteristics of these two types of alloys. Recent work on the effect of heat input on the properties of weldments of duplex stainless steels is reviewed.

Jan 1, 1990

By M. G. Spengler

Mr More O'Ferrall must be complimented on a paper that will be a useful reference for the re-working of previously abandoned workings. His paper so closely mirrors experiences at East Rand Proprietary Mines, Limited, that it could well have been based on occurrences in that mine. Corrosion The Scientific Society of Mechanical Engineers is organizing the 115th event of the European Federation for Corrosion in Budapest, from 18th to 22nd October 1982.

Jan 1, 1981

By G. V. R. Landman

Changes in the explosion behaviour of mixtures of coal dust, methane, and air when exposed to different energy sources are discussed. Changes to the lower explosive limits, minimum ignition energies, and rates of pressure rise when the same hybrid mixture of coal dust, methane, and air is exposed to ignition sources which are either spatially extended or spatially concentrated, are examined. A diagram is presented from which coal-dust loadings and methane presence can be determined which are below the lower explosible limits, and stated as a safety factor.

Jan 1, 1995

By H. E. James

GOLD 100, the most comprehensive international conference on gold ever held anywhere in the world, took place in Johannesburg from 14th to 18th September, 1986. The Conference was followed by a series of one day visits and an extended technical tour. The Conference was organized jointly by the Council for Mineral Technology (Mintek), the Chamber of Mines of South Africa, the School of Business Leadership of the University of South Africa, and The South African Institute of Mining and Metallurgy.

Jan 1, 1986

By E. J. Boome, A. C. Schmidt

Pert, and how Pert techniques can be used in modern mine management By E. J. Boome, A. C. Schmidt C.A. (S.A.) This paper covers the stages of planning required to be performed and the implementation of the plan from grass roots to the partial completion of the sinking of a mine shaft system. The various steps involved in the planning are also examined in some detail. The experience gained in this project and the conclusions reached convince the authors that Pert Planning is a valuable aid to top management.

By L. Dison

This technical note is issued in two parts, as follows: Part I, after a brief introduction, discusses the value of patents and the law of patents, including patent applications and the exploitation of inventions. This is followed by some comments for the benefit of would-be inventors and potential users of patents. Part II, which will appear in the February issue of this Journal, focuses on the mining industry and then discusses views on patents that were Quoted in Part I. The last section makes recommendations as to how II1ventors and users (including mining authorities) should handle patents.

Jan 1, 1992

By J. A. Cox, R. P. H. Willis, J. R. Dixon, A. D. Pooley

The paper describes the issues that should be considered when introducing mechanization to a mining operation. In South Africa, traditional methods of mining are well entrenched after more than a century of mining. To successfully change from these methods requires an integrated holistic approach that considers all aspects of a mining operation including setting of objectives, selection of personnel, recruitment, training and remuneration policies, organizational design, mine design, equipment selection, maintenance philosophy, standards and procedures, and monitoring and control. The paper makes reference to experience gained during a variety of on-mine case studies in drawing generic conclusions and making recommendations.

Jan 1, 2004

By W. Bleloch

In the process described, hydrogen is used to generate high-temperature steam and oxygen in the molten bath. Steel is decarburized to low levels to produce a pearlite-free steel suitable for deep drawing. The process makes use of the favourable thermodynamics in the reactions between steam, carbon, and iron, as well as providing high-temperature oxygen for the decarburizing reaction. The process can easily be incorporated in existing BOF (basic oxygen furnace) plant but can also be contemplated as a greenfield process.

Jan 1, 1987

By Colin M. Spence

If one is to discuss sensibly and beneficially the whole spectrum of education, training, and employment of engineers, it is not possible to confine oneself to Professional Engineers because the profession of engineering embraces also technologists, technicians, and those people known in South Africa as certificated engineers. It would therefore be imprudent if this seminar were to be limited to certain sectors of the profession and industry. I hope that it will review the full situation from top to bottom and from side to side. New President of FAPA Mr Douglas H. Mills took office as President of the Federation of Societies of Professional Engineers on 1st July, 1985.

Jan 1, 1985