Search Documents

By E. G. King

This paper reports measurements of low-temperature heat capacities and entropies at 298.15° K. of two copper ferrites (CUFe204 and CU0.75Fe2.2504). These substances, which occur in copper-smelting slags, have not been sujected to any previous direct thermodynamic investigation. The two copper ferrites are spinel minerals of the variate class. In previous investigations similar data were obtained for 13 other spinel minerals -7 of the normal class and 6 of the variate class. The entropies at 298.15° K. of these minerals have been compiled and revised as necessary in the light of present knowledge regarding structural randomness; entropy values, recommended for use in thermodynamic calculations, are listed.

Jan 1, 1959

By Wilbur I. Duvall

In this report, the Bureau of Mines presents a theoretical solution for the stresses and displacements in an infinite elastic plate containing a circular hole the boundary of which is loaded by applied radial stresses over four separated arcs. The problem solved is a two-dimensional approximation of the stresses and displacements developed by a large tunnel-boring machine anchored in a circular tunnel. Analysis of the solution shows that the tangential tensile stresses induced on the boundary of the circular opening can be minimized in the roof and maximized in the floor of the opening by proper spacing and loading of the four arcs.

Jan 1, 1967

By G. Nuñez, M. A. Pathak, C. F. Stanley

"A 1986 report by the U.S. National Committee on Blomechanlcs (1) describes lung disease as a major national health problem. The report cites three areas that would benefit from a better understanding of the vibratory patterns of the lung. These areas are outlined below.1. In cases of respiratory distress, pressure driven artificial respirators are used. A new technique using high frequency respiration is quite promising, but the pressure distribution in the lung as a function of frequency is not yet known. At these frequencies of 1 to 60 Hz, the lung expands asynchronously (2) and a better understanding of these expansion nonunlformltles could provide valuable Information about the mechanics of high frequency ventilation.2. Listening to the sounds In the lung can yield valuable Information about the state of the lung. To improve the technique, a better understanding of how acoustic waves propagate through the lung is needed.3. The response of the lung as It Is subjected to acoustic excitation, dynamic loading or shock waves is not well understood. A better knowledge of these responees can lead to improved treatment for patients subjected to either explosive pressure waves or car crashes.4. Researchers are measuring the acoustic Impedance of the Iung to detect early states of dysfunction. Sneckenberger and Whitmoyer (3) have reported Impedances obtained at acoustic frequencies up to about 6000 Hz. However, It la not certain which parts of the lung are responding to the acoustic excitation.To Investigate the vibratory characteristics of the lung, excised rat lungs were excited via the trachea with acoustic waves at frequencies up to 6000 Hz. Thie paper describes an Instrumentation system, utlllzlng time-averaged holographic Interferometry, to detect and quantify the response of the lung surface to the acoustic excitation."

Jan 1, 1989

Determine safe practices for surface mine blasting near pressurized gas, oil, and water transmission pipelines. Background Surface mine blasters regularly have to address the issue of how blasting affects transmission pipelines that run near and sometimes through their permit areas. Regulatory approaches to blasting have ranged from no regulation at all to strict limits intended to prevent cosmetic cracks in plaster interior walls of homes, but they have not directly addressed the impact of blasting on nearby pipelines. Concerned with both productivity and safety, the mining industry and its regulators have requested guidance on safe practices for mining near pipelines. The Pipeline Research Group of the American Gas Association has sponsored studies of the effects of small close-in blasts because of vibration concerns related to the installation of new pipes into existing pipeline right-of-ways. By contrast, the recent study in which the U.S. Bureau of Mines (USBM) took part is the first addressing large-scale mining blasts.

Jan 1, 1995

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

5. General Escapeway Requirements 5.1 Escape Routes Present escapeway regulations state "Every mine shall have two separate properly maintained escapeways to the surface which are so positioned that damage to one shall not lessen the effectiveness of the other, or a method of refuge shall be provided when only one opening to the surface is possible." "Escape routes shall be a. Inspected at regular intervals and maintained in safe, travellable condition, b. Marked with conspicuous and easily read direction signs that clearly indicate the ways of escape." "Application. "Regular" intervals means at intervals no greater than monthly where conditions are stable and oftener where conditions may change." "Designated escapeways inclined more than 30* from the horizontal shall be equipped with stairways, ladders, cleated walkways, or emergency hoisting facilities." As can be noted in present and proposed regulations there must be two separate properly maintained escapeways. In most operations, the escapeways will consist of one route that is the normal travelway used in day to day operations. The second route is usually a return airway through old work areas. Based on this generally accepted practice, we will designate the two types as primary and secondary.

Jan 1, 1976

By Richard L. Lewis

This is a discussion of the application of the zonal harmonic series to problems involving dipole sources in the vicinity of spherical boundaries. The application of a formal zonal-harmonic series solution to directly obtain numerical results involves two distinct problems: namely, the convergence of the series solution and the accurate calculation of the special functions involved in the series solution. Some interesting techniques will be introduced which help to improve the convergence properties of the series solution.

Jan 1, 1973

By Charles L. Kimbell

This study is intended to serve three roles. First, it represents a global overview and summary to supplement and complement the five regional companion volumes of the 1991 edition of the Minerals Yearbook International Review. In this regard, it also extends previous time series under this title that appeared as the introductory chapter to the international volume of the Minerals Yearbook from the inception of that volume in 1963 until it was subdivided into separate regional volumes in 1989. The basic statistical presentations herein generally contain data through and including that for 1991, although in a few instances the most recent statistics are those for earlier years because more recent, comprehensive global statistics simply are not yet available owing to delays in data collection and processing in some countries and continued governmental suppression of data in others. The second role of this study is to provide an update to the coverage of events impacting the world's mineral industry that have occurred between the end of 1991 and the preparation of this study. Inclusion of this update is almost essential because of the potential effect of some of these events on global mineral industry activities.

Jan 1, 1993

By B. Dimitriades

Exploration of the photochemical reactivity of diesel-exhaust hydro-carbons is described. A smog chamber was built, and reactivities of diesel exhaust, gasoline exhaust, and propylene were measured at two chamber temperatures. Experimental data indicated the problems caused by instability of diesel-exhaust hydrocarbons. With reservations due to these problems, the results are interpreted to reflect comparable reactivities for diesel and gasoline exhaust.

Jan 1, 1971

By D. R. Tesarik, R. W. McKibbin, J. B. Seymour

Displacement and stress changes in cemented backfill and ore pillars at the Buick Mine, near Boss, MO, were monitored by engineers from the U.S. Bureau of Mines and The Doe Run Co., St Louis, MO. A test area in this room-and-pillar mine was backfilled to provide support when remnant ore pillars were mined. Objectives of this research were to evaluate the effect of backfill on mine stability, observe backfill conditions during pillar removal, and calibrate a numeric model to be used to design other areas of the mine. Relative vertical displacements in the backfill were measured with embedment strain gauges and vertical extensometers. Other types of instruments used were earth pressure cells (to identify loading trends in the backfill), borehole extensometers (to measure relative displacement changes in the mine roof and support pillars),and biaxial stress meters (to measure stress changes in several support pillars and abutments). Two- and three-dimensional numeric codes were used to model the study area. With information from these codes and the installed instruments, two failed pillars were identified and rock mass properties were estimated.

Jan 1, 1995

By J. J. Geraghty

U.S. Bureau of Mines researchers investigated the development of an innovative transport system for underground coal mining. A one-half commercial-scale bench model was constructed. Novel magnetic levitation (mag-lev) technology was developed. Frictionless and contact-free transport of a prototype materials container and payload has been demonstrated.

Jan 1, 2010

Objective To develop and evaluate the effectiveness of safety training tools specific to underground metal/nonmetal mining. Background In a series of stakeholder meetings held in the western United States beginning in 1998, participants identified a critical lack of appropriate training materials applicable to metal/nonmetal mining. Participants in the meetings provided many insights into what types of training materials are most effective in dealing with both experienced and inexperienced miners. Most important was that the materials should be realistic and interesting and that some way should be found to capture the wisdom and expertise of older miners before they retired. In response, training videos that focus on safe practices during the mining cycle are being produced. Two videos one on handling explosives underground and one on identifying roof hazards and proper scaling techniques were completed during1999, and a third video is now available. This video, entitled “Ground Support...It’s Important, or Miner Mike Saves the Day,” presents information on why ground supports work and how to install them properly. Approach The new video, “Ground Support…It’s Important,” presents a scenario in which two young miners make a bad decision to leave some supports out in order to catch up in their mining cycle. An expert miner, “Miner Mike,” sees this potentially disastrous situation and educates the young miners about what could happen if they continued to leave supports out. He introduces the young miners to several expert miners, who explain how to install different types of supports correctly, as well as share what experience has taught them over the years. How It Works All footage was taken in operating, underground mines, using14 experts to provide the teaching. Because of the wide variety of supports used underground, it was necessary to focus on those types more common to hard-rock mining. While more complex support systems, such as shotcrete and cable bolts, are mentioned, detailed material is not included. In the course of educating young miners Jeff and Jason, Miner Mike provides information on— •Why supports are necessary in underground mines. •The main types of supports commonly used in underground hard-rock mines. •How supports work. •How holes for bolts are drilled correctly using jacklegs, drill jumbos, and bolting jumbos.• How wire mesh, wire panels, metal mats, and different types of bolts, including mechanical bolts, friction bolts, grouted bolts, and cable bolts, are installed properly. •How to recognize that supports have failed and what to do about it.

Jun 1, 2000

By Irven A. Jacobson

The thermal reactions of l-methylindole were studied in the temperature range of 525° to 627° C in a flow reactor. The major products consisted of 2-methylindole, 3-methylindole, indole, quinoline, hydrogen, and methane. 2-Methylindole is formed from 1-methylindole by an irreversible isomerization reaction. The 2-methylindole isomerizes in a reversible manner to 3-methyl-indole, the equilibrium favoring the 3-methyl isomer. Indole is formed directly from 1-methylindole. Quinoline is formed from l-methylindole, 2-methylindole, and 3-methylindole.

Jan 1, 1971

By H. W. Frevert, A. C. Fieldner, S. H. Katz

"The Bureau of Mines, in its investigations of as masks for use in mines and allied industries tests masks that are voluntarily submitted by manufacturers for examination, and issues approval certificates for masks that meet the bureau's specifications. This paper describes the tests that were conducted on an ammonia gas mask by the Bureau of Mines, which successfully met all requirements and tests for ammonia, masks. The mask tested, known as the GMD ammonia gas mask, is manufactured by the Mine Safety Appliances Co., Pittsburgh, Pa. This ammonia gas mask, which forms a pocket over the face and allows breathing through the nose, consists of a face-piece with non-shatter eyeglasses; this is attached by means of a corrugated rubber tube to a canister supported on wearer's chest by a harness. The canister is green in color and is of tinplate construction. It was a disc valve at the bottom to prevent exhalation through the canister. The filling of the canister consists of a specially impregnated activated charcoal, about 750 c.c. in volume and weighing about 520 grunn. The material is supported above the check valve by a dome of wire screen covered with toweling. Above the granular material is a filter of absorbent cotton screens, and all materials are hold firmly in place by pressure from strong"

May 1, 1926

By W. W. Adams

"Fatal accidents at coal mines throughout the United States killed 234 employees during January 1924, according to reports from State mine inspectors to the Bureau of Mines of the Department of the Interior, Included in the number of fatalities are 68 deaths caused by two explosions during the month, one explosion occurring in a mine at Johnson City, Ill., and causing 32 deaths, and the other in a mine at Shanktown, Pa., and causing 36 deaths. The fatality rate for the month was 3.94 per million tons, based on a production of 59,435,000 tons of coals In January 1923 the fatality rate was 3.52, based on 206 deaths and an output of 58,458,000 tons.Bituminous mines in all States reported 202 fatal accidents, the production being 51,170,000 tons., and the fatality rate being 3.92, as compared with 3.28 for January last year, For the anthracite mines in Pennsylvania, the reports covered 32 fatalities, which, on the month's output of 7,955,000 tons, indicated a fatality rate of 4.02 per million tons, as against 4.89 for January 1923.As compared with January 1923, the reports for January of the present year indicated lower fatality rates per million tons for all of the main causes of accidents except explosions. For falls of roof and coal, the fatality rate per million tons declined from 1.85 in January 1923 to 1,68 in January 1924; for haulage accidents the rate declined from 0.62 to 0.42; for explosives, from 0.19 to 0.12; for electricity, from 0.12 to 0.07. The rate for explosions increased from 0.21 to 1,31 per million tons. -- Reports of Investigations, Department of the Interior, Bureau of Mines."

Feb 1, 1924

By M. J. Brnich

The purpose of this U.S. Bureau of Mines study was to assess the ability of trainees to don an unfamiliar self-contained self-rescuer (SCSR) after having become familiar with how to put on a different type of apparatus. Prepractice instruction was the same for all individuals learning to put on a device: a step-by-step, hands-on talk-through using the "3+3" method. Subjects were assigned to groups that had their initial donning instruction delivered on either the Draeger OXY-SR60B or the CSE SR-100. Trainees' performances were then evaluated using the other model. Donning trials were analyzed using a number of measures. It was found that SCSR design had a moderate influence upon how well the donning task transferred.

Jan 1, 2010

Improve ground control in longwall gate entries by developing a practical method for evaluating longwall pillar designs. Background Longwalls have emerged as the most important technology to be applied to underground mining since the continuous mining machine. Longwall mines currently produce more than 30 pct of all the underground coal mined in the United States, up from less than 5 pct just 15 years ago. Safe longwall mining depends on maintaining ground control in the gate entries, the lifelines that provide access to the longwall face. In multientry retreat mining as practiced in the United States, rows of chain pillars are left to protect the gate entries (see figure 1). Chain pillars are subject to severe and complex abutment loads during the process of longwall panel extraction. The design of these pillars is often the single most important element in gate entry ground control and has been the subject of intensive Bureau of Mines research.

Jan 1, 1991

Crosson and Peters treat the errors that result in miner location due to errors in the overburden earth model used for computing location. A parallel effort by J. Powell of PMSRC is discussed here, where the location method used is that of the Westinghouse location program - "Miner". This location program was tested by Powell by using arrival times generated from the overburden earth model of Table l* rounded to the nearest millisecond. Location computations were then made using 3 geophones at a time. The average location is tabulated for all geophone triplets except when 3 geophones are in line. Geophone arrays were as shown in Tables 2 and 3. The manner in which the test was done is illustrated in Figure 1. I. SUMMARY OF RESULTS The arrival time differences, based on the Table 1 earth model, together with geophone locations based on the array geometries of Tables 2 and 3, were entered into the computer, together with a stated depth of 700 feet and an estimated overburden seismic velocity of 10,000 feet per second. These parameter values were processed by the location program - "Miner". Figure 2 illustrates the interpretation of the plots and data. The tabular data and plots of Table 4 and Figures 3, 4, and 5 illustrate the location error results obtained. These plots indicate that for sources within the array, the errors are considerably less than the measured errors obtained during field tests of the present location system. The possible reasons for this discrepancy are noted in Part Eight (Earth Models).

Jan 1, 1974

Enhance the critical skill of hazard recognition among miners by providing quality training that can help jot performance and lead to a higher degree of safety in the workplace. Background In mining, as in many other occupations, the safety of the worker depends on his or her ability to recognize hazards in the workplace. Some of the information needed by the miner for recognizing potential areas of danger is available in the form of visual cues found throughout the mine. One aspect of the dynamic mine environment it which the task of hazard recognition is critical for al workers is that of ground control. Regardless of job responsibilities, every worker is continuously exposed to roof rib, and floor hazards. Fatality injury data for the "underground coal" segment of the mining industry continue to show that about half of all fatalities are due to falls of ground each year. It is hypothesized that some of these accident, can be prevented if miners are better able to recognize visual cues that forewarn of potential roof and rib problems.

Jan 1, 1992

By Ann G. Kim

Methane in coal constitutes a serious hazard in coal mining. Draining the methane in advance of mining can mitigate this hazard, conserve energy, and offer economic benefits. This Bureau of Mines report evaluates the Pittsburgh coalbed in Greene County, Pa., to determine if advance drainage is feasible. The gas content of virgin reserves in Greene County is estimated at 100 to 200 ft3/ton, a total of over 370 billion ft3 of gas in an area approximately 310 mi2. Because of the similarity to natural gas, drained coalbed gas could be recovered and added to pipeline supplies of natural gas. The value of conserved gas would offset the cost of drainage and extend energy resources.

Jan 1, 1975

By L. C. Headley

Surface areas of two synthetic and three natural consolidated porous samples were obtained by the Orr low-pressure permeametry technique. The results suggest that the Orr technique is a useful substitute for the low-temperature gas adsorption (BET) method for determining the surface area of rock samples. It was more rapid than the BET method, and the surface-area values obtained were larger but agreed better with BET values than values calculated from the Kozeny-Carman equation. Efforts were unsuccessful to demonstrate the influence of channel-size distribution on pressure-flow rate curves by means of experimental data and a parallel channel model.

Jan 1, 1971