Search Documents

By L. C. IlsLey

In the normal operation of mines, the aggregate effect of many seemingly minor op rations may be very important as respects economy and safety. Anion: these operations is the method employed in coupling and uncoupling mine cars. For economic reasons the equipment in mines has not been protected as well as railroad equipment. It is pertinent that haulage accidents rank second in severity among mine accidents, and that manual coupling of cars has been one of the most frequent causes of such accidents. One study4/ revealed that coupling was responsible for about 20 percent of haulage accidents underground. A review of early conditions on steam railroads, which were responsible for the introduction of safer methods of coupling cars, indicates how conditions in might be improved. THE STORY OF RAILROAD COUPLING As any considerable improvement in mine-car coupling probably will follow lines somewhat similar to those that brought order out of chaos for the railroads, it seems appropriate to review briefly the steps taken to improve railroad coupling from the days of link and pin couplings of various types to the adoption of the standard ?M.C.E? automatic coupler.

Jan 1, 1943

By Wing G. Agnew, Albert E. Long

"SUMMARY AND CONCLUSIONSTests conducted at Mount Weather indicate that clear water is the best bit coolant and cuttings-removal medium for diamond drilling. All of the mediums tested did show that drilling speed increased when drilling with the faster feed ratios (greatest pressure on the bits). In no case, how¬ever, did the increased drilling speed amount to over 16 percent, and even in a long hole the slight increase in drilling speed would be more than offset by the extra time consumed in setting up.Bit wear was excessive when lubricating agents were used, the most footage per bit was obtained when drilling with clear water in the normal manner, and the next best footage was obtained when drilling with circulated water containing no lubricating agent. The diamonds showed little or no wear in any of the bits, and all bits cut well throughout the tests. They were only taken out of service when erosion of the cast metal had progressed to the point where the diamonds were about to roll out. The lubricating agents evidently hold some of the cuttings in suspension, which in turn help to cut the rock but also wear the metal of the bit.No hard-matrix bits were tested, and it is possible that one or more of the lubricating agents might increase the efficiency of such a bit by keeping it sharp and doing away with the necessity of sharpening by sand blasting. Some tests are planned with hard-matrix-type bits and the same lubricating agents used in the tests under discussion, but it is realized that any drilling advantage gained by the bits sharpening themselves may but at least partly offset by excessive wear of the Pump parts."

Jan 1, 1945

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Colombia has been prepared from the best available information in Washington, but is released subject to correction and amplification; if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State. SYNOPSIS OF LAW Minerals in Colombia belong to the owner of the soil unless otherwise provided in the law. The following lands and deposits, however, are described as fiscal property of the State: Class 1. The public lands, mines, and salines which belong to the individual States (now Departments) prier to the adoption of the present constitution (1886).

Jan 1, 1929

By John E. Pahlman

The Bureau of Mines investigated the feasibility of removing heavy metals from mineral-process waste streams by precipitation with lignochemicals and humic acids. Lignochemicals are by products from the paper industry, while humic acids are obtained by caustic treatment of peat, subbituminous coal, and lignite. These high-molecular-weight organic materials have many functional groups, which can coordinate and form innercomplex salts with heavy metals that are crystalline precipitates. Filtering of a humic-acid-or lignochemical-treated solution or waste stream containing these precipitates removes the heavy metal sequstrates. Tests were conducted with two lignochemical samples, three humic acid samples, lime (CaO), and sodium hydroxide (NaOH) in which increasing amounts of these additives were reacted with 50 mL of solution containing Fe3+ , Al3+, Cr3+, Pb2+, Cu2+, Cd2+, Zn2+, Co2+, Ni2+, Mn2+, and Hg1+. At the appropriate pH, greater than 90-and 99-pct removal was achieved for these 11 heavy metal ions from the 10-and lOO-ppm solutions, respectively, using lignochemicals and humic acids. Removal efficienC)' with these organic materials is better than that with CaO, especially for the more toxic ions, Hg1+, Cd2+, and Pb2+. Unlike the precipitates formed with NaOH or CaO, those with lignochemicals and humic acids are compact and noncolloidal. The volume of their sludge is sharply lower than that of the finely dispersed lime or soda precipitates; thus, their removal in settling tanks or by simple filtration is enhanced.

Jan 1, 1988

By M. G. Zabetakis

This publication presents a simplified graphic method for determining the explosibility of mine atmospheres under mine-fire conditions from mine- atmosphere composition data. Sometimes it is necessary to seal part of a mine during a fire to exclude air and thus extinguish the fire. Unfortunately, liberation of methane and formation of hydrogen and carbon monoxide in the sealed area may create an ex- plosive or flammable atmosphere if enough oxygen is present to support combustion. On the other hand, the oxygen concentration may be reduced through combustion processes and the concentration of inert gases (nitrogen and carbon dioxide) increased enough to render the atmosphere within the sealed area non-explosive. Before an area is unsealed, it is extremely important to know if the sealed atmosphere contains Flammable gases in proportions that might form explosive mixtures when air is introduced. If an explosive mixture forms and the fire is rekindled, a gas explosion will result. Various experimental methods may be used to determine the explosibility of a particular mine atmosphere; however, these methods usually are impracticable in the field.

Jan 1, 1959

By L. W. Kelly

The purpose of this circular is to show that, under the conditions prevailing in the Stony Point mine, wooden bolts were just as satisfactory as steel bolts or conventional timbering, with a reduction of approximately 80 percent in cost of material. This one fact alone is enough to justify an experiment with wood. This circular will show that production records have remained constant with both wooden and steel roof bolts. INTRODUCTION The successful use of steel roof bolts is now an accomplished fact in the coal industry, but the use of wooden bolts in place of steel is a rarity. The first experiment with wooden roof bolts was mane in 1949 in the Rio Verde mine, Norton Coal Corp., Nortonville, Ky.2/ This experiment was successful; the company obtained excellent results, but operations in the mine were suspended before enough time had elapsed to prove the value of wooden roof bolts conclusively. It is obvious that, if wooden roof bolts could be used in place of steel bolts or conventional timbering-methods, every mine operator would use word, as the cost is only a fraction of the other two methods. The Stony Point experience has proved conclusively that, under certain conditions and with a certain type of roof, wooden roof bolts can be used successfully.

Jan 1, 1952

By R. V. Ramani, A. S. C. Owili-eger

The quantity of methane emitted into the mine atmosphere and the movement of gas through solid coal and the adjoining country rock are dependent on the physical properties of the medium, boundary con¬ditions, the initial gas pressure distribution, and the combination of natural and mining factors. Functional relationships between these factors are not yet known. Consequently, the development of rigorous mathematical models to predict methane flow into the mine air is difficult and to date no model has been reported which is capable of such a function. Thus far, empirical formulas available for the calculation of gas quantity released from underground sources require too much his¬torical data, not currently available. Again, these estimations are at best only crudely approximate. The numerical methods available have not been made practical enough for industry wide application. Therefore, the development of a relationship amenable to numerical analysis and practical enough for use in the industry would provide the flexibility lacking in analytical approaches. The mathematical models given in equations (7) and (8) are further attempts in presenting practical models for predicting the quantity of methane emission into the mine environment. Equation (7) is the steady state model and equation (8) is the unsteady state model.

Jan 1, 1974

Provide reliable, early-warning fire detection instruments, telemetry, and control systems for noncoal underground mines. Approach Industrial-grade fire detection instruments and signal telemetry equipment were modified for long-term exposure to harsh underground mine conditions, then were installed in four mines to evaluate long-term performance and reliability. How It Works The elapsed time between the onset of a fire and its detection is critical because fires tend to grow in size and intensity with time. Early fire detection and warning permit the initiation of a mine's emergency plan (evacuation, fire fighting, etc.) while the fire is still small, or ideally, while it is still in the incipient stage. Fire detection and warning systems, utilizing sensitive heat, flame, smoke, and gas analyzers, provide the most rapid and reliable indication of a developing fire.

Jan 1, 1987

By N. H. Coates

A small, special-purpose centrifugal compressor was developed to circulate 60 pounds per hour of helium at 1,000° F and 250 psig because standard, commercial units were not available. Performance characteristics of this compressor were determined at helium flows of 2,000 to 18,000 std cu ft per hour, pressures of 100 to 250 psig, and temperatures of 100° to 1,000° F. This range is 2 to 90 actual cu ft per minute. Several graphs show the adiabatic head developed by the compressor over this wide flow range at various combinations of temperature and pressure. A compressor performance map relates pressure ratio to mass flow, temperature, pressure, and speed. This map can be used to accurately predict compressor performance factors within the range of operating conditions covered by the experiments.

Jan 1, 1963

By G. L. Leumann

"INTRODUCTION AND SUMMARYThe Andover-Sulphur Hill iron mines in Sussex County, N. J., have a production record extending over 100 years. The last production recorded was about 1880. These mines produced high-grade ore of two types: Red ore (hematite) and blue on (magnetite). Some sulfides (lead, zinc, and copper) were found underlying the iron deposits. Data as to size and grade of these sulfide bodies are very sketch"",Howard J. Hewitt of Elizabeth, N. J., lessee of the Sulphur Hill mines from 1940-45, prospected for lead, zinc, and copper. .His only production was several hundred tons of low-grade iron ore, which was crushed and used as heavy aggregate to make concrete blocks for ship ballast.In October and November 1942 made a magnetic survey of this area and bored six-diamond-drill holes with the dual objective of prospecting for sulfides and testing for extensions of the iron-are deposits indicated by the magnetic survey. 2/ In 1944, an iron-mining company examined this property and diamond-drilled seven holes. Between December 1949 and March 1950, the Bureau of Mines in search of sulfide deposits, bored three additional diamond-drill holes. Two of these were on the Sulphur Hill tract and one on the adjoining Tar Hill tract."

Sep 1, 1952

By R. E. Head

[Surveys of the manganese situation conducted by the Geological Survey any other agencies have definitely established the, fact that the tonnage of high-grade manganese or in the United States is relatively small. It is therefore obvious that large-scale production of manganese is possible only through beneficiation of low-grade material. Deposits of low-grade manganese ore are being examined by engineers of the Mining Division of the Bureau of Mines to determine their size and possibilities as sources of manganese on a tonnage basis. The Metallurgical Division of the Bureau is developing and perfecting beneficiation processes with the objective of utilizing such low-grade ores. Microscopic study of these ores represents one phase of the research.]

Jan 1, 1941

By R. E. Head

[Surveys of the manganese situation conducted by the Geological Survey and other agencies have distinctly established the fact that the tonnage of high- grade manganese ore in the United States is relatively small. It is therefore obvious that large-scale production of manganese is possible only through beneficiation of low-grade material. ]

Jan 1, 1941

By Leonard Greenburg

The analytical procedure necessary when using this new impinger•bubbler eil)paratus is almost identical with that em:r;,loyed with the Palm0r a:pp8.ratua. As sugar is not employei, the new apparatus por.;sesses the advantage over the eug.r tube method in having vsry low control errors, being, therefore, much simple in laboratory manipulation during analysis.

Aug 1, 1922

By M. M. Jones

Natural brines are potential domestic resources of minerals. The brines of Searles Lake, CA, for example, contain an estimated one-fourth of our current reserve of tungsten. A key to Bureau of Mines research to recover this critical mineral is the ability to quantitatively measure concentrations of particular constituents in the large number of brine samples and process solutions produced under a multiplicity of test conditions. This paper describes procedures used to determine arsenic, boron, phosphorus, silicon, and tungsten in these solutions by simultaneous inductively coupled plasma spectrometry. A variable in-ternal standard method was used to compensate for tungsten interference on the other analytes in tungsten concentrates, and matching standards were used to determine tungsten in raw brine. Other solutions were analyzed using normal techniques. Analytes were determined down to 1 mg/L with an average precision of 2.5 pet relative standard deviation. Accuracy, estimated using synthetic solutions and by comparison with values obtained by other methods, averaged about 2.5 pet. The methods were rapid, required little sample preparation, and provided the needed sensitivity.

Jan 1, 1985

By W. M. Myers

Water has been commonly used as a collecting medium in many instruments employed in the sampling of dusty atmospheres in mines** add industrial plants, and for this purpose has much to recommend it, particularly the following factors:1.,Water is a very efficient dust collector.2.,Distilled water of great purity may be readily obtained at slight expense. The analytical error introduced by the extremely small amount of foreign matter in carefully distilled water is very small,3.,Water is a very convenient medium with which to work as all the analytical operations of diluting, aliquoting, and filtering are readily and speedily carried out. Water has therefore been used extensively in such instruments as the Palmer apparatus, the Greenburg-Smith impinger, and the dust collector recently described by Drinker, Thompson, and Fitchet. The Bureau of Mines has conducted investigations in many metal-mining districts of the country, determining of dust the nature and amount of dust present in working places, its effect the health of workers, and what precautions may be taken to decrease the hazard of exposure to dangerous dusts. The Bureau is therefore interested in any factor that affects the accuracy of dust sampling.

Nov 1, 1923

By V. F. Parry

 The amount of energy required to support a unit volume of industrial production appears to depend on the volume of industrial production, effi- ciency of utilization of fuel, the form of energy used, climate, and popula- tion served. Previous to the first World War, industries of the United States were learning how to use the vast resources of energy that were available. From 1895 to 1900 the total amount of energy produced was equivalent to 3.7 tons of 13,100 B.t.u. coal per capita, but from that period until 1920 the energy used increased steadily until it reached an average of 7.7 tons per capita. Since that time the amount used has fluctuated with business con- ditions and has averaged 6.9 tons per capita.

Jan 1, 1943

By H. W. Wainwright

1. A schematic diagram and a description of the apparatus are presented. 2. Five runs were made using gas having a hydrogen-carbon monoxide ratio of about 2:1 and sulfur concentrations ranging from nil to 1.53 grains per 100 std. c.f. 3. At constant space velocity of synthesis gas the product of the sulfur concentration and days of operation, with conversion of H2 + CO above 97 percent, was constant. With a gas containing 0.04 grain of sulfur ac carbonyl sulfide per 100 std, cu. ft ,, the conversion of H2 + CO remained over 97 percent for 40 days. During that time the heating value of the product gas (on a C02-free basis) remained relatively constant at 940 B .t .u. per c.f., based on dry gas measured at 600 F. and 30 inches Hg.

Jan 1, 1954

By J. P. Rider

Health surveillance efforts indicate that the development of lung disease and overexposure to respirable dust in underground coal mires continues to afflict mine worker. Results from the most recent round (1992 - 1996) of the Coal Worker's X-ray Surveillance Programs indicate that approximately 8% of the examined miners who had at least 25 years of mining experience were diagnosed with Coal Worker Pneumoconiosis (CWP) (category 1/0+). During the period between 1995-1999, mine operators and MSHA inspectors collected 9968 and 1365 dust samples respectively, from longwall designated occupation (DO) personnel. Analysis of these samples showed that 1970 (20%) of the mine operator samples and 25.8 (19%) of the MSHA samples5 exceeded the 2 mg/m3 dust standard. The continued development of CWP in coal mine workers and the magnitude of respirable dust over-exposures in longwall mining occupations illustrate the need for improved dust control technology on longwalls. Figure 1 illustrates the major longwall dust sources as determined in the early 1990's.4 This article describes the ongoing research to find ways to minimise shearer dust levels as a function of changes in dust control parameters, and research to determine the impact of high air velocities on shield dust entrainment.

By L. D. Wyant

[A convenient method for the, analysis of oil-wax mixtures has bean developed in the petroleum laboratory of the Bureau of Mines. This method has been found useful in studying the characteristics of the products obtained in petroleum refineries during the manufacture of ?wax distillate?, "foots oil", ?intermediate wax", and commercial paraffin. In this method ac-to-au is used as a selective solvent.]

Jan 1, 1924

By A. G. Starliper

Laboratory studies were made to produce whiskers of tungsten over a wide range of operating temperatures. Hydrogen reduction of tungsten hexachloride in a vacuum furnace at temperatures from 2,7000 to 3,3000 C yielded a small quantity of tungsten whiskers, provided a low degree of supersaturation was maintained. Direct measurements of 3,000,000 to 4,000,000 psi were obtained for the ultimate tensile strengths of individual whiskers averaging 3 to 4 microns in diameter with average aspect ratios of 1,000. This compares with strengths of 300,000 to 400,000 psi for 13-micron-diameter commercial filaments.

Jan 1, 1968